English dropdown-ico

Manual ADDER SV2

34 pages 1.76 mb
Download

Go to site of 34

Summary
  • ADDER SV2 - page 1

    SMAR T V V i i e e w w I N S T A L L A T I O N & U S E www .addertec.com SMAR T Vie w 2 SV2 SMAR T Vie w 4 SV4 SMAR T V V i i e e w w ...

  • ADDER SV2 - page 2

    SmartView Installation and Use Page 1 About this manual SmartView - Installation and Use Sixth edition (April 1999) Part No. ADD0026/6 (c) 1999 Adder Technology Ltd. All rights reserved. Whilst every precaution has been taken in the preparation of this manual, Adder Technology Ltd assumes no responsibility for errors or omissions. Neither is any li ...

  • ADDER SV2 - page 3

    SmartView Installation and Use Page 2 Radio Frequency Energy Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances. European EMC directive 89/336/EEC This equipment has been tested and found to comply with ...

  • ADDER SV2 - page 4

    SmartView Installation and Use Page 3 Contents 1. Introduction ..................................................................................... 5 1.1 Key features ........................................................................................... 5 1. 2 Package contents .................................................................. ...

  • ADDER SV2 - page 5

    SmartView Installation and Use Page 4 4. SmartView configuration options ................................................. 21 4.1 Screen saver time delay ........................................................................ 21 4.2 Display options ...................................................................................... 21 4.3 Autosc ...

  • ADDER SV2 - page 6

    SmartView Installation and Use Page 5 1. Introduction Thank you for purchasing the Adder SmartView. Your SmartView is a high performance keyboard, monitor and mouse sharing device which supports a wide range of PC hardware and software platforms. 1.1 Key features Control multiple PCs from a single keyboard, monitor and mouse. SmartBoot feature auto ...

  • ADDER SV2 - page 7

    SmartView Installation and Use Page 6 1.2 Package contents SmartView. Power s upply suitable for your country. This installation guide. 1.3 Product information Fig. 1(a). SmartView (SV4 version supporting 4 PCs) ...

  • ADDER SV2 - page 8

    SmartView Installation and Use Page 7 Fig. 1 (b). SmartView (SV2 version supporting 2 PCs) Fig. 1 (c) - Remote control pad / display (optional accessory for 4 port models) ...

  • ADDER SV2 - page 9

    SmartView Installation and Use Page 8 2. Installation 2.1 What you will need Cables to connect the SmartView to each of your PC keyboard, video and mouse ports. Cable specifications are given in appendix A. (You do not need to connect a mouse cable if you are not using the mouse). A monitor with a standard VGA/SVGA (15 pin) connector that will work ...

  • ADDER SV2 - page 10

    SmartView Installation and Use Page 9 Use of PS/2 and RS232 style mice with the SmartView - All of the mouse connections from SmartView to PCs support either a PS/2 or an RS232 mouse. SmartView automatically converts from the PS/2 mouse commands to RS232 serial mouse commands. Serial mice types are selected by using an adapter as described in Appen ...

  • ADDER SV2 - page 11

    SmartView Installation and Use Page 10 the monitor and each of the computers in turn. Failure to switch the SmartView and computers on in the correct order can lead to the mouse and/or keyboard not being recognised by the computers when they are switched on. 2.4 Configuring your PCs Configure you PC in the same way that you would if your keyboard, ...

  • ADDER SV2 - page 12

    SmartView Installation and Use Page 11 In configure mode, options are entered by typing a letter followed by a number followed by (enter). Use ESC to abort the entry of an option. The SmartView will remain in configure mode until you type 'E' (enter). For example: to set hotkey option 2 type the following at the 'C' prompt (at S ...

  • ADDER SV2 - page 13

    SmartView Installation and Use Page 12 T1 - 2 seconds autoscan delay time before switching to next port (default) T2 - 5 seconds autoscan delay time before switching to next port T3 - 7 seconds autoscan delay time before switching to next port T4 - 10 seconds autoscan delay time before switching to next port T5 - 15 seconds autoscan delay time befo ...

  • ADDER SV2 - page 14

    SmartView Installation and Use Page 13 P - Sets password - see section 4.7 for instructions. E - Exits configure mode and returns the SmartView to normal operation mode. 2.7 Other useful installation information PC boot up sequence - When your PCs are powered on they communicate with any attached keyboards and mice and setup parameters required by ...

  • ADDER SV2 - page 15

    SmartView Installation and Use Page 14 With the PS/2 mouse disconnected, change the channel using the keypad or keyboard hotkeys. The SmartView detects that the mouse has been disconnected and triggers the automatic recovery system. Plug in the PS/2 mouse and the SmartView will re-initialise it. 2.9 Hot plugging the SmartView into running systems a ...

  • ADDER SV2 - page 16

    SmartView Installation and Use Page 15 Type of mouse / system Driver ty pe Likely expected Suggested Connected at bootup data format restoration PS/2 PS/2 only PS/2 F5 PS/2 IntelliMouse PS/2 F5 IntelliMouse / SmartView PS/2 only PS/2 F5 IntelliMouse / SmartView IntelliMouse IntelliMouse F6 To restore lost mouse movement on a CPU connected to the Sm ...

  • ADDER SV2 - page 17

    SmartView Installation and Use Page 16 3. Using the SmartView This section explains the general operation of the SmartView. We recommend that you read this section before starting to use the product. 3.1 Power on status At power on the SmartView selects PC number 1 and displays '1'. If a password has been set then ‘P’ will be displaye ...

  • ADDER SV2 - page 18

    SmartView Installation and Use Page 17 3.4 Keyboard hotkey control SmartView can be conveniently controlled by selecting channel, autoscan mode or security locking from the keyboard. All of the hotkey control commands are invoked by holding down the two hotkeys and then pressing a command key. By default, the two hotkeys are ‘CTRL’ and ‘ALT? ...

  • ADDER SV2 - page 19

    SmartView Installation and Use Page 18 channels (see section 4.9) then only the active channels will be selected. Otherwise the SmartView will cycle through all channels when using HOTKEYs + TAB. The hotkey command are summarised below (note that the numbers on the numeric keypad do not form part of a valid hotkey) : ‘HOTKEYs’ and ‘1’ - sel ...

  • ADDER SV2 - page 20

    SmartView Installation and Use Page 19 To 'tab through' channels: press ba ba v v release v press v v release v press v v release vba 3.5 Mouse control The channels can conveniently be changed on ADDERview by using a three button mouse. In order to switch to the next channel simply hold down the central mouse button (the wheel mouse butto ...

  • ADDER SV2 - page 21

    SmartView Installation and Use Page 20 data booster and can each be up to 30 metres away from the next SmartView. The channel can be selected on remote SmartView units using an extension of the HOTKEY control function. For example, consider a situation where two SmartView 4 port units are connected together as shown below. To connect to the compute ...

  • ADDER SV2 - page 22

    SmartView Installation and Use Page 21 4. SmartView configuration options All the options described in this section are entered in SmartView configure mode - see section 2.5 for instructions on entering configure mode. 4.1 Screen saver time delay SmartView contains a programmable screen saver which will blank the display after the set time delay wi ...

  • ADDER SV2 - page 23

    SmartView Installation and Use Page 22 D1 - Display dot flashes to indicate activity, right handed auxiliary display (default) D2 - Display dot does not flash, right handed auxiliary display D3 - Display dot flashes to indicate activity, left handed auxiliary display D4 - Display dot does not flash, left handed auxiliary display D5 - Display dot fl ...

  • ADDER SV2 - page 24

    SmartView Installation and Use Page 23 Many modern monitors are fitted with automatic power save relays and will switch off after a few seconds if connected to an inactive PC. If you are using such a monitor you must not use the L2 feature. Constant switching on and off of your monitor's relay will eventually damage your monitor. 4.4 Mouse mod ...

  • ADDER SV2 - page 25

    SmartView Installation and Use Page 24 U1 - SmartView channels are switchable using a 3 button mouse or IntelliMouse (default) (SmartView reports 2 button mouse mode to PCs) U2 - SmartView channels are not switchable using 3 button mouse or IntelliMouse (SmartView reports 2 button mouse mode to PCs) U3 - SmartView channels are not switchable using ...

  • ADDER SV2 - page 26

    SmartView Installation and Use Page 25 4.6 Firmware functions (version query, mouse restore and reset) For technical support purposes, it may be necessary to find the firmware release version for the control software in your SmartView. For example, if the release version is v1.02 the response shown to F1(enter) will be a brief display of the digit ...

  • ADDER SV2 - page 27

    SmartView Installation and Use Page 26 keyboard (except ctrl, alt, shift and enter). Consequently the following 'password' would be valid: oFRED g g 4.8 Cascade query code The SmartViews use a special ‘query code’ to detect whether or not they are connected to another SmartView. By default your SmartView uses query code AD. SmartView ...

  • ADDER SV2 - page 28

    SmartView Installation and Use Page 27 Appendix A. Cable and connector specifications IMPORTANT NOTE The maximum cable lengths supported vary widely between devices and cables. It may be possible to use cables that are longer than those specified below with certain PCs and peripherals but this cannot be guaranteed. If you experience problems try us ...

  • ADDER SV2 - page 29

    SmartView Installation and Use Page 28 RS232 serial mice - these require a special converter to connect the RS232 lines present on the SmartView mouse ports to the RS232 port on a PC. The wiring is identical to that used by Microsoft for their autosensing mouse adapter and is shown below: Cables should be no longer than 30 metres. A3. Expansion por ...

  • ADDER SV2 - page 30

    SmartView Installation and Use Page 29 Appendix B. Problem Solving Problem: Poor video quality with smearing fuzziness or ripple. Action: Use screened coaxial video cables to connect your devices to the SmartView. Problem: Mouse does not move cursor on screen. Action: Ensure that the mouse and computer are both connected to SmartView before the pow ...

  • ADDER SV2 - page 31

    SmartView Installation and Use Page 30 Problem: Mouse causes channel to change. Action: Some cheaper mice are not fully compatible with the SmartView and can lose data causing the channel to be changed (if mouse switching of channels is enabled). If you experience this problem then change the mouse and use a Microsoft, Logitech, IBM, Compaq or Hewl ...

  • ADDER SV2 - page 32

    SmartView Installation and Use Page 31 Notes ...

  • ADDER SV2 - page 33

    SmartView Installation and Use Page 32 Notes ...

  • ADDER SV2 - page 34

    SMAR T V V i i e e w w INST ALLA TION & USE ADDER T echnology Limited T echnolog y House T rafalgar W a y Bar Hill Cambridge CB3 8SQ • England T : +44 (0) 1954 780044 F: +44 (0) 1954 780081 sales@addertec .com www .addertec .com SV -05.02/V1 ...

Manufacturer ADDER Category Network Card

Documents that we receive from a manufacturer of a ADDER SV2 can be divided into several groups. They are, among others:
- ADDER technical drawings
- SV2 manuals
- ADDER product data sheets
- information booklets
- or energy labels ADDER SV2
All of them are important, but the most important information from the point of view of use of the device are in the user manual ADDER SV2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals ADDER SV2, service manual, brief instructions and user manuals ADDER SV2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product ADDER SV2.

Similar manuals

A complete manual for the device ADDER SV2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use ADDER SV2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of ADDER SV2.

A complete ADDER manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual ADDER SV2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the ADDER SV2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the ADDER SV2, that we can find in the current document
3. Tips how to use the basic functions of the device ADDER SV2 - which should help us in our first steps of using ADDER SV2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with ADDER SV2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of ADDER SV2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning ADDER SV2?

Use the form below

If you did not solve your problem by using a manual ADDER SV2, ask a question using the form below. If a user had a similar problem with ADDER SV2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)