English dropdown-ico

Manual Spalding 211376A

18 pages 0.52 mb
Download

Go to site of 18

Summary
  • Spalding 211376A - page 1

    1 05/03 P/N 211376A Customer Service N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. A Huffy Comp any WRITE IN YOUR MODEL NUMBER: __________ REQUIRED TOOLS AND MA TERIALS: • Two People • Tape Measure • Tape • Shovel and Spade • Concrete, 900 lb. (408 kg) and Container to Mix • Carpenter’s Level • Wood Board (Scrap) • Ste ...

  • Spalding 211376A - page 2

    2 P/N 211376A 05/03 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolt s into large holes of elevator tubes, backboard bracket s and triangle plates. Carefully rock them in a circular motion to ream out any excess p aint from ho ...

  • Spalding 211376A - page 3

    05/03 P/N 211376A 3 F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, suppor t braces or net. • During play , especially when performin ...

  • Spalding 211376A - page 4

    4 P/N 211376A 05/03 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL 1. Make sure ground is level with playing surface, then dig pole hole. 2. CONTACT UTILITIES BEFORE DIGGING. W ARNING! Correctly identify each pole section and mark indicated distance from ends with tape. BOTTOM MIDDLE 3 5-1/2” (14 cm) TOP 5-1/2” (14 c ...

  • Spalding 211376A - page 5

    05/03 P/N 211376A 5 5. Fill hole approximately 3/4 full with concrete. Tamp down concrete to release air pockets. PLAYING SURFACE Insert bottom pole section (3) into ground sleeve (4). 3. 4. Assemble clamps (7) around bottom pole and ground sleeve (4) as shown. 5 5 8 8 7 4 7 6 6 IMPORT ANT! CLAMP ASSEMBLY MUST BE POSITIONED AS SHOWN BELOW. 7 4 3 ...

  • Spalding 211376A - page 6

    6 P/N 211376A 05/03 6. Insert ground sleeve (4) and pole section (3) into hole. Fill remaining hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Center and level ground sleeve assembly in hole. Check leveling on all sides several times while concrete is curing. NOTE: Make sure concrete is set up to clamp assembl ...

  • Spalding 211376A - page 7

    05/03 P/N 211376A 7 C O N C R E T E 1" (2.54cm) IMPORT ANT! Bounce pole top (1) and middle section (2) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 4-1/2" (11.4 cm) minimum overlap. IMPORT ANT! Add bottom pole section (3) to assembly. Bounce pole sections together 3 times, rota ...

  • Spalding 211376A - page 8

    8 P/N 211376A 05/03 14. Lower clamp cover (12) over clamps and snap into proper position. 13. Secure clamps (7) around pole section as shown. Refer to Step 4. Tighten completely. 12. 11 12 12 3 12 IMPORT ANT! ELEVATOR HOLES MUST BE PARALLEL WITH PLAYING SURFACE. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT ...

  • Spalding 211376A - page 9

    05/03 P/N 211376A 9 F R O N T 17 14 19 13 18 16 14 15 15 18 14 15. Beginning with top hole in left and right screw jack support plates (16 & 17), install elevator tubes (15) to pole as shown. Then secure lower holes in support plates to pole. NOTE: Not all holes in support plates (16 & 17) are used in this assembly. IMPORT ANT! DO NOT OVER ...

  • Spalding 211376A - page 10

    10 P/N 211376A 05/03 1 7 9 8 11 7' 2.1m 20 22 21 24 24 IMPORT ANT! DO NOT OVER TIGHTEN. 23 POLE 14 18 18 21 15 15 16 17 14 17. 18. Center screw jack (21) between support plates (16 & 17) and secure as shown below. Attach logo label (22) to height indicator cover (23). Place cover (23) over screw jack (21). Install pole cap (11). 16. Attach ...

  • Spalding 211376A - page 11

    05/03 P/N 211376A 11 ½ 13 14 18 14 15 15 26 26 Secure upper elevator tubes (15) to pole assembly as shown. 19. Insert spacer (25) through top holes of height indicator cover (23) and screw jack assembly as shown. Align spacer (25) and screw jack assembly between elevator tubes (15) and secure. 20. IMPORT ANT! WHEN SECURING SCREW JACK (21) TO TOP E ...

  • Spalding 211376A - page 12

    12 P/N 211376A 05/03 7' 2.1m 18 14 30 30 14 30 30 14 18 18 18 14 14 14 27 15 15 15 15 28 28 22. NOTE: Two people recommended for this operation. Attach Y-frame support bracket (27) to elevator tubes (15) as shown. NOTE: Same hardware used for upper and lower installation. 21. Loosely assemble bolt (28) and nut (29) to Y-frame support bracket ( ...

  • Spalding 211376A - page 13

    05/03 P/N 211376A 13 ½ 29 28 27 23. Lift backboard upright and insert bolt (28) heads into key slots. Slide backboard downward to position bolt (28) into channel as shown. Align rim mounting holes on Y-frame support bracket (27) to rim holes on backboard and tighten completely. IMPORT ANT! ALIGN RIM MOUNTING HOLES WITH HOLES IN Y- FRAME TWO PERSON ...

  • Spalding 211376A - page 14

    14 P/N 211376A 05/03 24. 25. ½ 33 31 29 Attach rim (33). Note: Mounting nuts (29) and bolts (31) supplied with rim hardware. USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. Install net clips (34). WARNING The Quick Clip™ rapid ...

  • Spalding 211376A - page 15

    05/03 P/N 211376A 15 Position looped end of height adjustment crank (36) onto hook as shown. Rotate crank handle to raise or lower backboard. View label (20) to determine approximate backboard height. 27. 26. Height Adjustment HOOK 36 20 STORE CRANK OUT OF REACH OF CHILDREN. DO NOT ALLOW CHILDREN TO ADJUST HEIGHT WITHOUT ADULT SUPERVISION COULD RES ...

  • Spalding 211376A - page 16

    16 P/N 211376A 05/03 H U FFY HUFFY SP ORTS 10 feet (3.05 m) 37 REGULATION RIM HEIGHT IS 10 FEET (3.05 M). 28. Apply height adjustment label (37) to front of pole as shown. Secure pole pad (32) as shown. 29. 32 ...

  • Spalding 211376A - page 17

    05/03 P/N 211376A 17 P ARTS LIST HARDW ARE IDENTIFIER * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item Qty. Part No. Description 1 1 900757 Top Pole Section 2 1 900874 Middle Pole Section, Flared End 3 1 908215 Bottom Pole Section 4 1 206500 Ground Sleeve, Square 5 2 201124 Lock Nut, Hex Head, 3/8 x 16 6 4 203232 Washer, Flat, 3/8 x 3/4 O.D. 7 2 20 ...

  • Spalding 211376A - page 18

    18 P/N 211376A 05/03 HARDW ARE IDENTIFIER (CONTINUED) * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item #25 (1) Item #29 (6) Item #30 (4) Item #31 (4) Item #34 (12*) Item #28 (2) Item #26 (2) Item #24 (2) ...

Manufacturer Spalding Category Fitness Equipment

Documents that we receive from a manufacturer of a Spalding 211376A can be divided into several groups. They are, among others:
- Spalding technical drawings
- 211376A manuals
- Spalding product data sheets
- information booklets
- or energy labels Spalding 211376A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Spalding 211376A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Spalding 211376A, service manual, brief instructions and user manuals Spalding 211376A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Spalding 211376A.

Similar manuals

A complete manual for the device Spalding 211376A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Spalding 211376A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Spalding 211376A.

A complete Spalding manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Spalding 211376A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Spalding 211376A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Spalding 211376A, that we can find in the current document
3. Tips how to use the basic functions of the device Spalding 211376A - which should help us in our first steps of using Spalding 211376A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Spalding 211376A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Spalding 211376A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Spalding 211376A?

Use the form below

If you did not solve your problem by using a manual Spalding 211376A, ask a question using the form below. If a user had a similar problem with Spalding 211376A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)