English dropdown-ico

Manual JVC RX-D301S

92 pages 3.34 mb
Download

Go to site of 92

Summary
  • JVC RX-D301S - page 1

    LVT1321-001A [J] RX-D301S / RX-D302B A UDIO / VIDEO CONTR OL RECEIVER INSTR UCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. cover_RX-D301S[J]_f.p65 05.2.22, 16:44 3 ...

  • JVC RX-D301S - page 2

    W arnings, Cautions, and Others Mises en gar de , précautions et indications diver ses Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line. The power can be remote controlled. Attention—Touche STANDBY/ON! Déconnectez la fiche d’al ...

  • JVC RX-D301S - page 3

    1 T able of Contents P ar ts identification ................................................ 2 Getting started ...................................................... 4 Before Installation .................................................................. 4 Checking the supplied accessories ....................................... 4 Putting batteries ...

  • JVC RX-D301S - page 4

    2 Remote control See pages in parentheses for details . 1 TV/VIDEO button (36, 38) 2 Standby/on b uttons (14, 36 – 40) A UDIO , TV , DBS/CA TV , VCR , D VR/D VD 3 Source selecting buttons (14, 27, 36 – 40) TV , DBS, VCR, D VR/D VD , FM, AM, USB, D VD MUL TI 4 TV V OL (volume) +/– button (36, 38) 5 CHANNEL +/– button (36 – 40) 6 • Operat ...

  • JVC RX-D301S - page 5

    3 Front panel 1 ST ANDBY/ON button and standby lamp (14) 2 CC CONVERTER b utton (16) 3 SETTING button (17, 19) 4 ADJUST button (23) 5 SURROUND b utton (33) 6 Source lamps D VD MUL TI, D VR/D VD , VCR, DBS , TV , USB, FM, AM 7 • SET button (17, 19, 23) • TUNER PRESET button (28) 8 • SOURCE SELECTOR (14, 28) • MUL TI JOG (17, 19, 23, 28, 33) ...

  • JVC RX-D301S - page 6

    4 Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–). 3 Replace the cover . If the range or eff ectiveness of the remote control decrease ...

  • JVC RX-D301S - page 7

    5 Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed. AM loop antenna (supplied) If AM reception is poor, connect an outdoor single vinyl-covered wire (not supplied). AM antenna connection Con ...

  • JVC RX-D301S - page 8

    6 L R LS RS SBL C SW SBR (*SB) LEFT RIGHT LEFT RIGHT LEFT RIGHT SUBWOOFER OUT SURROUND SPEAKERS CAUTION:SPEAKER IMPEDANCE 6 - 16 SURROUND BACK SPEAKERS CENTER SPEAKER FRONT SPEAKERS Connecting the speakers Do not connect the A C power plug to the wall outlet until all connections are completed. Speaker Layout Diagram CA UTIONS: • Use speakers wit ...

  • JVC RX-D301S - page 9

    7 ı Ή Ï Ì Ç Å DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT This receiver is equipped with the f ollowing video terminals — composite video , S-video, and component video terminals. • If your video components ha ve S-video (Y/C-separation) and/or component ...

  • JVC RX-D301S - page 10

    8 7 Connecting a D VD recorder or D VD play er with its analog discrete output jacks (D VD MUL TI IN): This connection is the best connection method f or enjoying D VD Audio sounds. When a D VD Audio disc is pla yed bac k, the or iginal high- quality sounds can be reproduced only using this connection. T urn off all components bef ore making connec ...

  • JVC RX-D301S - page 11

    9 7 Connecting a VCR T urn off all components bef ore making connections. • When you connect other components , refer also to their manuals. Å T o component video output • Connect Y , P B , and P R correctly . ı T o left/right audio channel output Ç T o left/right audio channel input Î T o composite video output ‰ T o S-video output Ï T ...

  • JVC RX-D301S - page 12

    10 7 Connecting a TV Connect the TV to the appropriate MONITOR OUT jac ks to view the pla yback picture from any other connected video components. Stereo audio cable (not supplied) Red Component video cable (not supplied) TV Composite video cable (not supplied) Green Blue Red S-video cable (not supplied) White Å T o component video input • Conne ...

  • JVC RX-D301S - page 13

    11 DIGITAL OUT PCM/STREAM DIGITAL IN 2(DBS) 1(DVR/ DVD) 3(VCR) NO TES • When shipped from the f actor y , the DIGIT AL IN terminals have been set for use with the f ollowing components: – 1(D VR/D VD): F or D VD recorder or D VD play er – 2(DBS): F or DBS tuner – 3(VCR): F or VCR If you connect other components , change the digital input (D ...

  • JVC RX-D301S - page 14

    12 4. T urn on the receiver , then slide the USB WIRELESS switch on the rear to “ID LEARNING, ” and select the source as “USB WIRELESS. ” When you slide the s witch, the lamp in the switch starts flashing. 5. Set the volume to minim um. IMPORT ANT : Alwa ys set volume to “0” when connecting or disconnecting the other equipment. 6. Press ...

  • JVC RX-D301S - page 15

    13 Now PC is read y for playback thr ough the USB connection. After installation is completed, you can use y our PC as the playbac k source. The PC automatically recognizes the receiv er whenev er the transmitter is connected to the PC or the USB cable is connected between the PC and the receiv er while the receiver is turned on. • When not using ...

  • JVC RX-D301S - page 16

    14 Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECTOR until the sour ce name y ou want appears on the display . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECTOR, the source changes as follo ws: D VD MUL TI: Select the D VD player using the analog discrete output ...

  • JVC RX-D301S - page 17

    15 Selecting the digital decode mode If the f ollowing symptoms occur while playing Dolb y Digital or DTS software with “DGTL A UTO” selected (see page 14), follo w the procedure below: • Sound does not come out at the beginning of pla yback. • Noise comes out while searching f or or skipping chapters or trac ks. From the remote control ONL ...

  • JVC RX-D301S - page 18

    16 Basic adjustment of auto memory This receiv er memor izes sound settings f or each source: • when you turn off the power , and • when you change the source . When you change the source , the memor ized settings f or the newly selected source are automatically recalled. The follo wing can be stored for each source: • Analog/digital input mo ...

  • JVC RX-D301S - page 19

    17 T o obtain the best possible sound eff ect from Surround/DSP modes (see pages 29 to 33), you need to set up the speak er and subwoof er information after all the connections are completed. F rom pages 17 to 22, how to set speakers and other basic items of the receiv er are explained. Setting the speaker information easily — Quick Speaker Setup ...

  • JVC RX-D301S - page 20

    18 Speakers (channels) number and the size Y ou can find how each of the speak er size is defined according to the number of connected speakers (speak er channel “ ch ” number) you select. • Subwoof er is counted as 0.1 channel. The size of connected speak ers CH L/R C LS/RS SB SUBWFR 2.0CH LARGE NONE NONE NONE NO 2.1CH SMALL NONE NONE NONE Y ...

  • JVC RX-D301S - page 21

    19 Operating procedure On the front panel ONL Y : Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 1 again. Ex.: When setting DIGIT AL IN 1 terminal. 1 Press SETTING. MUL TI JOG now works for the setting operation. 2 T urn MUL TI JOG until the item ...

  • JVC RX-D301S - page 22

    20 In this case, set the distance as f ollows: Left front speaker (L): “FRONT L <3.0m> (10ft)” Right front speaker (R): “FRONT R <3.0m> (10ft)” Center speaker (C): “CENTER <3.0m> (10ft)” Left surround speaker (LS): “SURR L <2.7m> (9ft)” Right surround speaker (RS): “SURR R <2.7m> (9ft)” Left surroun ...

  • JVC RX-D301S - page 23

    21 Selecting the main or sub channel — DUAL MONO Y ou can select the playbac k sound (channel) you want while playing digital softw are recorded (or broadcasted) in Dual Mono mode (see page 30), which includes two monaural channels separately . When the receiver detects Dual mono signals , the DU AL MONO indicator lights up on the display . D MON ...

  • JVC RX-D301S - page 24

    22 Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 11) so that the correct source name will appear when you select the digital source. Select one of the follo wing components for each terminal: D VR ...

  • JVC RX-D301S - page 25

    23 Sound adjustments Y ou can make sound adjustment to y our preference after completing basic setting. Basic adjustment items Y ou can adjust the follo wing items. See pages in parentheses f or details. • Y ou cannot select the items which is not av ailable with the current setting. Items T o do SUBWFR L VL* 1 Adjust the subwoof er output level. ...

  • JVC RX-D301S - page 26

    24 Adjusting the equalization patterns — D EQ 63Hz/250Hz/1kHz/4kHz/16kHz Y ou can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers . • Once you hav e made an adjustment, it is memorized for each source. Adjustable range: – 8 (dB) to +8 (dB) (in 2 dB inter vals) ...

  • JVC RX-D301S - page 27

    25 Adjusting the bass sounds Reinforcing the bass — BASS BOOST Y ou can boost the bass lev el — Bass Boost. • Once you hav e made an adjustment, it is memorized for each source. B BOOST < ON > Select to boost the bass lev el. The B.BOOST indicator lights up on the displa y . B BOOST < OFF > Select to deactivate the Bass Boost. Ini ...

  • JVC RX-D301S - page 28

    26 Adjusting the center channel localization for Pro Logic IIx Music and Pro Logic II Music — CENTER WIDTH This setting is av ailable when Pro Logic IIx Music or Pro Logic II Music is activated f or the analog or digital 2-channel sound signal. T o activate Pro Logic IIx Music or Pro Logic II Music, see page 33. • If “ CENTER SPK ” is set t ...

  • JVC RX-D301S - page 29

    27 T uner operations T uning in to stations manually From the remote control ONL Y : 1 Press FM or AM to select the band. The last receiv ed station of the selected band is tuned in. 2 Press repeatedly or hold TUNING 9 or ( TUNING until the station y ou want is tuned in. • Pressing (or holding) TUNING 9 increases the frequency . • Pressing (or ...

  • JVC RX-D301S - page 30

    28 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel number position is flashing. • For channel n umber 5, press 5. • For channel n umber 15, press +10, then 5. • For channel n umber 30, press +10, +10, then 10. 4 Press MEMOR Y again while the selected channel number is flashing on the displa y . The s ...

  • JVC RX-D301S - page 31

    29 Creating realistic sound fields Reproducing theater ambience In a movie theater , many speakers are located on the walls to reproduce impressiv e multi-channel sound, reaching you from all directions. With these many speakers , sound localization and sound mov ement can be expressed. Surround/DSP modes built in this receiv er can create almost t ...

  • JVC RX-D301S - page 32

    30 DTS Neo:6 DTS Neo:6 is another conv ersion method to create 6-channel (plus subwoof er) from analog/digital 2-channel software by using the high precision digital matrix decoder used for DTS-ES Matrix 6.1ch. • This receiver pro vides the following DTS Neo:6 modes — Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC). When one of them i ...

  • JVC RX-D301S - page 33

    31 Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound — early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are dela yed by the distances of the ceiling and walls. These direct sounds a ...

  • JVC RX-D301S - page 34

    32 Using the Surround/DSP modes A vailable Surround/DSP modes v ar y depending on the speaker settings and the incoming signals . See the table below . • The numbers inside the parentheses follo wing the incoming signal type indicate the number of the front channels and that of the surround channels. For e xample, (3/2) indicates that the signals ...

  • JVC RX-D301S - page 35

    33 On the front panel: Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 2 again. 1 Select and play an y source other than D VD MUL TI. • Make sure you ha ve selected the input mode (analog or digital) correctly . 2 Press SURROUND . MUL TI JOG now ...

  • JVC RX-D301S - page 36

    34 AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III A V COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC ’ s video components (TV , D VD play er*, and VCR) through this receiver . This receiver is equipped with the A V COMPU LINK- III , which has added a functi ...

  • JVC RX-D301S - page 37

    35 One-touch DVD play Simply by starting playbac k on the D VD play er, y ou can enjoy the D VD playback without setting other s witches manually . • When the D VD player is connected through the analog input jacks on this receiv er (and analog input is selected), the receiver automatically turns on and changes the source to “ D VR/D VD ” or ...

  • JVC RX-D301S - page 38

    36 Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Refer also to the man uals supplied with the other products. – Some JVC VCRs can accept two types of the control signals — remote codes “ A ” and “ B. ” This remote control can operate a VCR whose remote control code is set t ...

  • JVC RX-D301S - page 39

    37 123 456 789 10 0 10 Y ou can alwa ys perform the follo wing operation: D VD/DVR : T ur n on or off the D VD recorder or D VD play er . After pressing D VR/D VD , you can perf or m the follo wing operations on the D VD recorder and D VD play er. 3 : Star t playbac k. 7 : Stop pla yback. 8 : P ause playbac k. T o release it, press 3 . ¢ : Skip to ...

  • JVC RX-D301S - page 40

    38 By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers ’ products. • Refer also to the man uals supplied with the other products. • T o operate those components with the remote control, first you need to set the manuf acturers ’ codes each for the TV , VCR, CA TV converter , DBS tun ...

  • JVC RX-D301S - page 41

    39 ❏ Changing the transmittable signals for operating a VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer ’ s code using buttons 1 – 9, and 0. See “ Manufacturers ’ codes for VCR ” on the r ight. 4 Release VCR . Now , you can perform the f ollowing operation on the VCR. VCR : T ur n on or off the VCR. After pressing VCR, ...

  • JVC RX-D301S - page 42

    40 Manufacturer Codes G.I. 01 Gemini 02 Hamlin 03, 04, 05, 06 Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15 Macom 16, 17, 18 Magnavox 19 Oak 20, 21, 22 Panasonic 23, 24 Philips 25, 26, 27, 28, 29, 30 Pioneer 31, 32 S. Atlanta 33, 34, 35 Samsung 36 Tocom 37 Zenith 38, 39 Manufacturer Codes JVC 01 Hitachi 02 Kenwood 03, 04 Magnavox 05 Marantz 06 Mitsubi ...

  • JVC RX-D301S - page 43

    41 T r oubleshooting Use this chart to help you solve daily operational prob lems. If there are any prob lems you cannot solv e, contact your JVC ’ s service center. PROBLEM The power does not come on. The receiv er tur ns off (enters standby mode). “ O VER HEA T ” flashes on the displa y , then the receiv er tur ns off. No sound from speaker ...

  • JVC RX-D301S - page 44

    42 Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 110 W per channel, min. RMS, driven into 6 Ω at 40 Hz to 20 kHz with no more than 0.8% total harmonic distortion. At surround operation: F ront channels: 110 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no m ...

  • JVC RX-D301S - page 45

    warranty.p65 05.2.22, 16:45 1 ...

  • JVC RX-D301S - page 46

    warranty.p65 05.2.22, 16:45 2 ...

  • JVC RX-D301S - page 47

    0205RYMMDWJEIN EN © 2005 Victor Company of Japan, Limited AUDIO / VIDEO CONTROL RECEIVER RX-D301S / RX-D302B cover_RX-D301S[J]_f.p65 05.2.22, 16:44 2 ...

  • JVC RX-D301S - page 48

    English Français LVT1321-002A [C] RX-D302B A UDIO / VIDEO CONTR OL RECEIVER RECEPTURE DE COMMANDE A UDIO/VIDEO INSTR UCTIONS MANUEL D ’ INSTR UCTIONS cover_RX-D301S[C]_f.p65 05.2.23, 16:24 3 ...

  • JVC RX-D301S - page 49

    W arnings, Cautions, and Others Mises en gar de , précautions et indications diver ses Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line. The power can be remote controlled. Attention—Touche STANDBY/ON! Déconnectez la fiche d’al ...

  • JVC RX-D301S - page 50

    1 English T able of Contents P ar ts identification ................................................ 2 Getting started ...................................................... 4 Before Installation .................................................................. 4 Checking the supplied accessories ....................................... 4 Putting b ...

  • JVC RX-D301S - page 51

    2 English Remote control See pages in parentheses for details . 1 TV/VIDEO button (36, 38) 2 Standby/on b uttons (14, 36 – 40) A UDIO , TV , DBS/CA TV , VCR , D VR/D VD 3 Source selecting buttons (14, 27, 36 – 40) TV , DBS, VCR, D VR/D VD , FM, AM, USB, D VD MUL TI 4 TV V OL (volume) +/ – button (36, 38) 5 CHANNEL +/ – button (36 – 40) 6 ...

  • JVC RX-D301S - page 52

    3 English Front panel 1 ST ANDBY/ON button and standby lamp (14) 2 CC CONVERTER b utton (16) 3 SETTING button (17, 19) 4 ADJUST button (23) 5 SURROUND b utton (33) 6 Source lamps D VD MUL TI, D VR/D VD , VCR, DBS , TV , USB, FM, AM 7 • SET button (17, 19, 23) • TUNER PRESET button (28) 8 • SOURCE SELECTOR (14, 28) • MUL TI JOG (17, 19, 23, ...

  • JVC RX-D301S - page 53

    4 English Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–). 3 Replace the cover . If the range or eff ectiveness of the remote control ...

  • JVC RX-D301S - page 54

    5 English Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed. AM loop antenna (supplied) If AM reception is poor, connect an outdoor single vinyl-covered wire (not supplied). AM antenna connec ...

  • JVC RX-D301S - page 55

    6 English L R LS RS SBL C SW SBR (*SB) LEFT RIGHT LEFT RIGHT LEFT RIGHT SUBWOOFER OUT SURROUND SPEAKERS CAUTION:SPEAKER IMPEDANCE 6 - 16 SURROUND BACK SPEAKERS CENTER SPEAKER FRONT SPEAKERS Connecting the speakers Do not connect the A C power plug to the wall outlet until all connections are completed. Speaker Layout Diagram CA UTIONS: • Use spea ...

  • JVC RX-D301S - page 56

    7 English ı Ή Ï Ì Ç Å DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT This receiver is equipped with the f ollowing video terminals— composite video , S-video, and component video terminals. • If your video components ha ve S-video (Y/C-separation) and/or co ...

  • JVC RX-D301S - page 57

    8 English 7 Connecting a D VD recorder or D VD play er with its analog discrete output jacks (D VD MUL TI IN): This connection is the best connection method f or enjoying D VD Audio sounds. When a D VD Audio disc is pla yed bac k, the or iginal high- quality sounds can be reproduced only using this connection. T urn off all components bef ore makin ...

  • JVC RX-D301S - page 58

    9 English 7 Connecting a VCR T urn off all components bef ore making connections. • When you connect other components , refer also to their manuals. Å T o component video output • Connect Y , P B , and P R correctly . ı T o left/right audio channel output Ç T o left/right audio channel input Î T o composite video output ‰ T o S-video outp ...

  • JVC RX-D301S - page 59

    10 English 7 Connecting a TV Connect the TV to the appropriate MONITOR OUT jac ks to view the pla yback picture from any other connected video components. Stereo audio cable (not supplied) Red Component video cable (not supplied) TV Composite video cable (not supplied) Green Blue Red S-video cable (not supplied) White Å T o component video input ? ...

  • JVC RX-D301S - page 60

    11 English DIGITAL OUT PCM/STREAM DIGITAL IN 2(DBS) 1(DVR/ DVD) 3(VCR) NO TES • When shipped from the f actor y , the DIGIT AL IN terminals have been set for use with the f ollowing components: – 1(D VR/D VD): F or D VD recorder or D VD play er – 2(DBS): F or DBS tuner – 3(VCR): F or VCR If you connect other components , change the digital ...

  • JVC RX-D301S - page 61

    12 English 4. T urn on the receiver , then slide the USB WIRELESS switch on the rear to “ID LEARNING, ” and select the source as “USB WIRELESS. ” When you slide the s witch, the lamp in the switch starts flashing. 5. Set the volume to minim um. IMPORT ANT: Alwa ys set volume to “0” when connecting or disconnecting the other equipment. 6 ...

  • JVC RX-D301S - page 62

    13 English Now PC is read y for playback thr ough the USB connection. After installation is completed, you can use y our PC as the playbac k source. The PC automatically recognizes the receiv er whenev er the transmitter is connected to the PC or the USB cable is connected between the PC and the receiv er while the receiver is turned on. • When n ...

  • JVC RX-D301S - page 63

    14 English Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECTOR until the sour ce name y ou want appears on the display . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECTOR, the source changes as follo ws: D VD MUL TI: Select the D VD player using the analog discrete ...

  • JVC RX-D301S - page 64

    15 English Selecting the digital decode mode If the f ollowing symptoms occur while playing Dolb y Digital or DTS software with “DGTL A UTO” selected (see page 14), follo w the procedure below: • Sound does not come out at the beginning of pla yback. • Noise comes out while searching f or or skipping chapters or trac ks. From the remote con ...

  • JVC RX-D301S - page 65

    16 English Basic adjustment of auto memory This receiv er memor izes sound settings f or each source: • when you turn off the power , and • when you change the source . When you change the source , the memor ized settings f or the newly selected source are automatically recalled. The follo wing can be stored for each source: • Analog/digital ...

  • JVC RX-D301S - page 66

    17 English T o obtain the best possible sound eff ect from Surround/DSP modes (see pages 29 to 33), you need to set up the speak er and subwoof er information after all the connections are completed. F rom pages 17 to 22, how to set speakers and other basic items of the receiv er are explained. Setting the speaker information easily — Quick Speak ...

  • JVC RX-D301S - page 67

    18 English Speakers (channels) number and the size Y ou can find how each of the speak er size is defined according to the number of connected speakers (speak er channel “ ch ” number) you select. • Subwoof er is counted as 0.1 channel. The size of connected speak ers CH L/R C LS/RS SB SUBWFR 2.0CH LARGE NONE NONE NONE NO 2.1CH SMALL NONE NON ...

  • JVC RX-D301S - page 68

    19 English Operating procedure On the front panel ONL Y : Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 1 again. Ex.: When setting DIGIT AL IN 1 terminal. 1 Press SETTING. MUL TI JOG now works for the setting operation. 2 T urn MUL TI JOG until t ...

  • JVC RX-D301S - page 69

    20 English In this case, set the distance as f ollows: Left front speaker (L): “ FRONT L <3.0m> (10ft) ” Right front speaker (R): “ FR ONT R <3.0m> (10ft) ” Center speaker (C): “ CENTER <3.0m> (10ft) ” Left surround speaker (LS): “ SURR L <2.7m> (9ft) ” Right surround speaker (RS): “ SURR R <2.7m> (9f ...

  • JVC RX-D301S - page 70

    21 English Selecting the main or sub channel — DUAL MONO Y ou can select the playbac k sound (channel) you want while playing digital softw are recorded (or broadcasted) in Dual Mono mode (see page 30), which includes two monaural channels separately . When the receiver detects Dual mono signals , the DU AL MONO indicator lights up on the display ...

  • JVC RX-D301S - page 71

    22 English Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 11) so that the correct source name will appear when you select the digital source. Select one of the follo wing components for each termin ...

  • JVC RX-D301S - page 72

    23 English Sound adjustments Y ou can make sound adjustment to y our preference after completing basic setting. Basic adjustment items Y ou can adjust the follo wing items. See pages in parentheses f or details. • Y ou cannot select the items which is not av ailable with the current setting. Items T o do SUBWFR L VL* 1 Adjust the subwoof er outpu ...

  • JVC RX-D301S - page 73

    24 English Adjusting the equalization patterns — D EQ 63Hz/250Hz/1kHz/4kHz/16kHz Y ou can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers . • Once you hav e made an adjustment, it is memorized for each source. Adjustable range: – 8 (dB) to +8 (dB) (in 2 dB int ...

  • JVC RX-D301S - page 74

    25 English Adjusting the bass sounds Reinforcing the bass — BASS BOOST Y ou can boost the bass lev el — Bass Boost. • Once you hav e made an adjustment, it is memorized for each source. B BOOST < ON > Select to boost the bass lev el. The B.BOOST indicator lights up on the displa y . B BOOST < OFF > Select to deactivate the Bass Bo ...

  • JVC RX-D301S - page 75

    26 English Adjusting the center channel localization for Pro Logic IIx Music and Pro Logic II Music — CENTER WIDTH This setting is av ailable when Pro Logic IIx Music or Pro Logic II Music is activated f or the analog or digital 2-channel sound signal. T o activate Pro Logic IIx Music or Pro Logic II Music, see page 33. • If “ CENTER SPK ” ...

  • JVC RX-D301S - page 76

    27 English T uner operations T uning in to stations manually From the remote control ONL Y : 1 Press FM or AM to select the band. The last receiv ed station of the selected band is tuned in. 2 Press repeatedly or hold TUNING 9 or ( TUNING until the station y ou want is tuned in. • Pressing (or holding) TUNING 9 increases the frequency . • Press ...

  • JVC RX-D301S - page 77

    28 English 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel number position is flashing. • For channel n umber 5, press 5. • For channel n umber 15, press +10, then 5. • For channel n umber 30, press +10, +10, then 10. 4 Press MEMOR Y again while the selected channel number is flashing on the displa y ...

  • JVC RX-D301S - page 78

    29 English Creating realistic sound fields Reproducing theater ambience In a movie theater , many speakers are located on the walls to reproduce impressiv e multi-channel sound, reaching you from all directions. With these many speakers , sound localization and sound mov ement can be expressed. Surround/DSP modes built in this receiv er can create ...

  • JVC RX-D301S - page 79

    30 English DTS Neo:6 DTS Neo:6 is another conv ersion method to create 6-channel (plus subwoof er) from analog/digital 2-channel software by using the high precision digital matrix decoder used for DTS-ES Matrix 6.1ch. • This receiver pro vides the following DTS Neo:6 modes — Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC). When one o ...

  • JVC RX-D301S - page 80

    31 English Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound — early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are dela yed by the distances of the ceiling and walls. These direct ...

  • JVC RX-D301S - page 81

    32 English Using the Surround/DSP modes A vailable Surround/DSP modes v ar y depending on the speaker settings and the incoming signals . See the table below . • The numbers inside the parentheses follo wing the incoming signal type indicate the number of the front channels and that of the surround channels. For e xample, (3/2) indicates that the ...

  • JVC RX-D301S - page 82

    33 English On the front panel: Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 2 again. 1 Select and play an y source other than D VD MUL TI. • Make sure you ha ve selected the input mode (analog or digital) correctly . 2 Press SURROUND . MUL TI ...

  • JVC RX-D301S - page 83

    34 English AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III A V COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , D VD play er*, and VCR) through this receiver . This receiver is equipped with the A V COMPU LINK- III , which has added a ...

  • JVC RX-D301S - page 84

    35 English One-touch DVD play Simply by starting playbac k on the D VD play er, y ou can enjoy the D VD playback without setting other s witches manually . • When the D VD player is connected through the analog input jacks on this receiv er (and analog input is selected), the receiver automatically turns on and changes the source to “ D VR/D VD ...

  • JVC RX-D301S - page 85

    36 English Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Refer also to the man uals supplied with the other products. – Some JVC VCRs can accept two types of the control signals — remote codes “ A ” and “ B. ” This remote control can operate a VCR whose remote control code ...

  • JVC RX-D301S - page 86

    37 English 123 456 789 10 0 10 Y ou can alwa ys perform the follo wing operation: D VD/DVR : T ur n on or off the D VD recorder or D VD play er . After pressing D VR/D VD , you can perf or m the follo wing operations on the D VD recorder and D VD play er. 3 : Star t playbac k. 7 : Stop pla yback. 8 : P ause playbac k. T o release it, press 3 . ¢ : ...

  • JVC RX-D301S - page 87

    38 English By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers ’ products. • Refer also to the man uals supplied with the other products. • T o operate those components with the remote control, first you need to set the manuf acturers ’ codes each for the TV , VCR, CA TV converter , ...

  • JVC RX-D301S - page 88

    39 English ❏ Changing the transmittable signals for operating a VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer ’ s code using buttons 1 – 9, and 0. See “ Manufacturers ’ codes for VCR ” on the r ight. 4 Release VCR . Now , you can perform the f ollowing operation on the VCR. VCR : T ur n on or off the VCR. After pressi ...

  • JVC RX-D301S - page 89

    40 English Manufacturer Codes G.I. 01 Gemini 02 Hamlin 03, 04, 05, 06 Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15 Macom 16, 17, 18 Magnavox 19 Oak 20, 21, 22 Panasonic 23, 24 Philips 25, 26, 27, 28, 29, 30 Pioneer 31, 32 S. Atlanta 33, 34, 35 Samsung 36 Tocom 37 Zenith 38, 39 Manufacturer Codes JVC 01 Hitachi 02 Kenwood 03, 04 Magnavox 05 Marantz 06 ...

  • JVC RX-D301S - page 90

    41 English T r oubleshooting Use this chart to help you solve daily operational prob lems. If there are any prob lems you cannot solv e, contact your JVC ’ s service center. PROBLEM The power does not come on. The receiv er tur ns off (enters standby mode). “ O VER HEA T ” flashes on the displa y , then the receiv er tur ns off. No sound from ...

  • JVC RX-D301S - page 91

    42 English Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 110 W per channel, min. RMS, driven into 6 Ω at 40 Hz to 20 kHz with no more than 0.8% total harmonic distortion. At surround operation: F ront channels: 110 W per channel, min. RMS, driven into 6 Ω at 1 kHz w ...

  • JVC RX-D301S - page 92

    0305RYMMDWJEIN EN, FR © 2005 Victor Company of Japan, Limited AUDIO / VIDEO CONTROL RECEIVER RX-D302B cover_RX-D301S[C]_f.p65 05.2.23, 16:24 2 ...

Manufacturer JVC Category Stereo Receiver

Documents that we receive from a manufacturer of a JVC RX-D301S can be divided into several groups. They are, among others:
- JVC technical drawings
- RX-D301S manuals
- JVC product data sheets
- information booklets
- or energy labels JVC RX-D301S
All of them are important, but the most important information from the point of view of use of the device are in the user manual JVC RX-D301S.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JVC RX-D301S, service manual, brief instructions and user manuals JVC RX-D301S. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JVC RX-D301S.

Similar manuals

A complete manual for the device JVC RX-D301S, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JVC RX-D301S by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JVC RX-D301S.

A complete JVC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JVC RX-D301S - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JVC RX-D301S, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JVC RX-D301S, that we can find in the current document
3. Tips how to use the basic functions of the device JVC RX-D301S - which should help us in our first steps of using JVC RX-D301S
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JVC RX-D301S
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JVC RX-D301S in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JVC RX-D301S?

Use the form below

If you did not solve your problem by using a manual JVC RX-D301S, ask a question using the form below. If a user had a similar problem with JVC RX-D301S it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)