Manual Summit S-460

32 pages 9.93 mb
Download

Go to site of 32

Summary
  • Summit S-460 - page 1

    YOU MUST READ THIS OWNER’S GUIDE BEFORE OPERATING YOUR GAS GRILL. m DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department. Leaking gas may cause a fire or explosion which can cause seri ...

  • Summit S-460 - page 2

    www . weber.com ® 2 DaNGers aND w arNiNGs m DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. m WARNINGS m Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. m Im ...

  • Summit S-460 - page 3

    www . weber.com ® 3 3 w arraNTY Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber ® gas grill that it will be free of defects in material and workmanship from the date of purchase as follows: Aluminum castings 25-years (2 years on paint; excludes fading) Stainless steel Shroud, 25-years; Porcelain-enameled ...

  • Summit S-460 - page 4

    www . weber.com ® 4 8 9 11 12 41 43 42 44 45 7 46 34 35 36 37 38 39 40 10 2 3 4 5 6 1 S460_LP_US 47 23 24 25 48 26 27 28 29 30 31 32 33 49 50 51 52 58 57 59 60 53 54 55 56 14 15 16 17 18 19 20 21 13 22 expl oDeD view s-460 ...

  • Summit S-460 - page 5

    www . weber.com ® 5 5 Shroud Har dw are 1. Shroud 2. Thermometer 3. Thermometer Bezel 4. Handle 5. Grill Out 6. TM Handle Light Rotisser ie Motor 7. Rotisser ie Brac ket 8. W arming Rac k 9. Cooking Grat es 1 0. Flav orizer 11. ® Bars Burner T ubes 1 2. Control P anel Wiring Harness 1 3. Manifold 1 4. Control P anel 1 5. Small Knob Bezel 1 6. Sma ...

  • Summit S-460 - page 6

    www . weber.com ® 6 OPERATING Liquid Propane (LP) gas supply is easy to use and gives you more cooking control than charcoal fuel. • Theseinstructionswillgiveyoutheminimumrequirementsforassemblingyour Weber ® gas barbecue. Please read the instructions carefully before using your Weber ® gas barbecue. Imprope ...

  • Summit S-460 - page 7

    www . weber.com ® 7 7 GeNeral iNsTruc TioNs IMPORTANT LP CYLINDER INFORMATION m DANGER m NEVER store a spare LP Cylinder under or near W eber ® gas appliances. m NEVER fill the tank beyond 80% full. m Failure to follow these statements exactly may result in a fire causing death or serious injury. LEAK CHECK PREPARATION CHECK THAT ALL BURNER VALVE ...

  • Summit S-460 - page 8

    www . weber.com ® 8 Gas iNsTruc TioNs Some LP tanks have differing top collar assembles. (The top collar is the metal protective ring around the valve.) One series of tanks mount with the valve facing front (a) . The other tanks mount with the valve facing away from the fuel scale (b) . Weber recommends the use of cylinder manufacturer’s Manches ...

  • Summit S-460 - page 9

    www . weber.com ® 9 9 CHECK FOR GA S LEAKS m W ARNING: The gas connections of y our Summit ® gas grill hav e been factory test ed. W e do howev er recommend that you leak c heck all gas connections bef ore oper ating y our Summit ® gas grill. A REMO VE CONTROL P ANEL P ar t requir ed: Phillips Screw driver . 1) Remov e the bur ner control knobs ...

  • Summit S-460 - page 10

    www . weber.com ® 10 A A 1 2 6 7 5 * The grill illustrated may have slight differences than the model purchased. CHECK: 1) Main gas line to manifold connection. 2) Rotisserie (I.R. Burner) gas line connection. 3) Bulkhead and gas supply hose connection. 4) Corregated gas line to bulkhead connection. m WARNING: If there is a leak at connection (1, ...

  • Summit S-460 - page 11

    www . weber.com ® 11 11 Gas iNsTruc TioNs REFILLING THE LIQUID PROPANE CYLINDER We recommend that you refill the LP cylinder before it is completely empty. Removal of the LP cylinder 1) Close cylinder valve (turn clockwise). 2) Unscrew regulator coupling by turning counterclockwise, by hand only. 3) Loosen cylinder lock wing nut and turn cylinder ...

  • Summit S-460 - page 12

    www . weber.com ® 12 Gas iNsTruc TioNs A B C D E SNAP IGNITION OPERATION m Always open the lid before igniting the burners Each control knob has its own igniter electrode built in. To create a spark you must push the control knob in (A) and turn to “START/High” (B) . This action will generate gas flow and a spark to the burner lighting tube (C ...

  • Summit S-460 - page 13

    www . weber.com ® 13 13 1 5 2 4 3 LIGHTING Summary lighting instructions are inside the left hand cabinet door. m DANGER Failure to open the lid while igniting the barbecue’s burners, or not waiting 5 minutes to allow the gas to clear if the barbecue does not light, may result in an explosive flame-up which can cause serious bodily injury or dea ...

  • Summit S-460 - page 14

    www . weber.com ® 14 opera TiNG iNsTruc TioNs MAIN BURNER MANUAL LIGHTING m DANGER Failure to open the lid while igniting the barbecue’s burners, or not waiting 5 minutes to allow the gas to clear if the barbecue does not light, may result in an explosive flame-up which can cause serious bodily injury or death. 1) Open the lid. 2) Make sure all ...

  • Summit S-460 - page 15

    www . weber.com ® 15 15 The most important thing to know about grilling is which cooking method to use for a specific food, Direct or Indirect. The difference is simple: place the food directly over the fire, or arrange the fire on either side of it. Using the right method is the shortest route to great results—and the best way to ensure donenes ...

  • Summit S-460 - page 16

    www . weber.com ® 16 USING THE SEAR ST A TION ™ Y our W eber ® gas barbecue includes a sear burner for searing meats such as steak, poultry par ts, fish, and chops). Searing is a direct grilling technique which br owns the surf ace of the food at a high temperatur e. By searing or browning both sides of the meat you will cr eate a mor e desirab ...

  • Summit S-460 - page 17

    www . weber.com ® 17 17 1) Open the lid. 2) Make sur e all burner control knobs are turned of f. (Push contr ol knob in and turn clockwise t o ensure that it is in the “OFF” position.) m W ARNING: The burner contr ol knobs must be in the “OFF” position befor e tur ning on the liquid propane c ylinder tank valv e. If the y are not in the ? ...

  • Summit S-460 - page 18

    www . weber.com ® 18 USING THE SMOKER The smoker uses presoaked wood chips. For best results with faster cooking foods like steaks, burgers and chops, etc., we recommend using finer wood chips because they ignite and create smoke faster. For longer cooking foods such as roasts, chicken and turkeys, etc., we recommend using larger wood chunks becau ...

  • Summit S-460 - page 19

    www . weber.com ® 19 19 opera TiNG iNsTruc TioNs LIGHTING THE SMOKER BURNER m DANGER Failure to open the lid while igniting the grill, or not waiting 5 minutes to allow the gas to clear if the grill does not light, may result in an explosive flare-up which can cause serious bodily injury or death. SMOKER BURNER SNAP IGNITION Note: The control knob ...

  • Summit S-460 - page 20

    www . weber.com ® 20 MANUALLY LIGHTING THE SMOKER BURNER m WARNING: Check hose before each use of grill for nicks, cracking, abrasions or cuts. If the hose is found to be damaged in any way, do not use the grill. Replace using only Weber ® authorized replacement hose. Contact the Customer Service Representative in your area using the contact info ...

  • Summit S-460 - page 21

    www . weber.com ® 21 21 opera TiNG iNsTruc TioNs USING THE ROTISSERIE Note: Before using your rotisserie, measure your food at the widest point. If it exceeds 9½" (241.8mm), it is too large to fit the rotisserie. If it is too large, food can be prepared using a roast holder and the Indirect Cooking Method. IMPORTANT SAFEGUARDS m WARNINGS • ...

  • Summit S-460 - page 22

    www . weber.com ® 22 LIGHTING THE ROTISSERIE BURNER ROTISSERIE BURNER SNAP IGNITION Note: Each control knob snap igniter creates a spark from the igniter electrode to the burner lighting tube. You generate the energy for the spark by pushing in the control knob and turning to “START/HI”. This will ignite each individual burner. m ATTENTION: RE ...

  • Summit S-460 - page 23

    www . weber.com ® 23 23 opera TiNG iNsTruc TioNs m DANGER When the “excess gas flow control” feature is activated, a small amount of gas is still flowing to the burners. After turning off the cylinder and burner control knobs, wait at least 5 minutes for the gas to clear before attempting to light the grill. Failure to do so may result in an e ...

  • Summit S-460 - page 24

    www . weber.com ® 24 opera TiNG iNsTruc TioNs MANUALLY LIGHTING THE ROTISSERIE BURNER m ATTENTION: READ BEFORE LIGHTING ROTISSERIE BURNER After a period of non-use, before lighting the Rotisserie Burner, a few seconds must pass for the gas supply line to fill. When holding a match to the rotisserie burner you will see a flash of flames moving from ...

  • Summit S-460 - page 25

    www . weber.com ® 25 25 OPERATING THE HANDLE LIGHT The Weber Grill Out ™ Handle Light has a built-in “Tilt Sensor.” With the power button (a) activated, the light will come on when the grill lid is open. The light will turn off when the lid is closed. For daytime use, deactivate the sensor by pressing power button (a) . haNDle liGhT Troubles ...

  • Summit S-460 - page 26

    www . weber.com ® 26 PROBLEM CHECK CURE Rotisserie burner does not light. Did you hold the burner control knob in and hold in for 20 seconds until after burner ignited? Try to relight burner by holding burner control knob in and continue holding in until 20 seconds after burner has ignited. Did you wait to see the entire ceramic surface become ali ...

  • Summit S-460 - page 27

    www . weber.com ® 27 27 maiNTeNaNce MAIN BURNER CLEANING PROCEDURE TURN OFF THE GAS SUPPLY. Remove the manifold (See “Replacing Main Burners”). Look inside each burner with a flashlight. Clean the inside of the burners with a wire (a straightened-out coat hanger will work). Check and clean the air shutter opening at the ends of the burners. Ch ...

  • Summit S-460 - page 28

    www . weber.com ® 28 maiNTeNaNce Be careful not t o break or disconnect the wires f or the control panel lights. Rest the contr ol panel against the lef t side of the grill (A) exposing the v alv es, b urners, igniter , and manifold. 8) Remov e the t wo screws that secur e the manifold t o the cookbox. P ull manifold assembl y out from the manif o ...

  • Summit S-460 - page 29

    www . weber.com ® 29 29 ANNUAL MAINTENANCE INSPECTION AND CLEANING OF THE SPIDER/INSECT SCREENS To inspect the Spider/Insect screens, remove the control panel. If there is dust or dirt on the screens, remove the burners for cleaning the screens. Brush the Spider/Insect screens lightly with a soft bristle brush (i.e. an old toothbrush). m CAUTION: ...

  • Summit S-460 - page 30

    ©2009 The f ollowing trademarks are registered in the name of Weber -Stephen P roducts Co ., an Illinois cor poration, located at 200 East Daniels Road, P alatine, Illinois 60067 U .S.A. Austr alia; Smoke y Joe, Weber , K ettle Silhouet te , Genesis, Austria; Ket tle Silhouett e , Smoke y Joe , Weber , Benelux; Ket tle Silhouette , Smokey Joe, W e ...

  • Summit S-460 - page 31

     PLEASE CONTINUE ON BACK / POR F A VOR CONTINÚE EN EL REVERSO / VEUILLEZ CONTINUER A U VERSO. ➤ ➤ ➤  ThaNK You F or purchasiNG a weber ® Grill. You’ve maDe a wise iNvesTmeNT , Now T aKe a Few miNuTes aND proTec T iT bY re GisTeriNG Your proDucT . Gracias por comprar uNa barba coa weber ® . usTeD ha he cho uNa acerT aD a iNversiÓN; ...

  • Summit S-460 - page 32

    ©2008 We ber-Stephen Products Co. All rights reserved. Printed in U.S.A. 557 98_0708   Thanks for sha ring your contact inform ation with us. Aga in, it all stays strictly between us — Weber does not sh are customers’ names with anyone else. If you need replacement pa r ts or have questions a bout the assembly, use or mai ntenance of you ...

Manufacturer Summit Category Gas Grill

Documents that we receive from a manufacturer of a Summit S-460 can be divided into several groups. They are, among others:
- Summit technical drawings
- S-460 manuals
- Summit product data sheets
- information booklets
- or energy labels Summit S-460
All of them are important, but the most important information from the point of view of use of the device are in the user manual Summit S-460.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Summit S-460, service manual, brief instructions and user manuals Summit S-460. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Summit S-460.

Similar manuals

A complete manual for the device Summit S-460, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Summit S-460 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Summit S-460.

A complete Summit manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Summit S-460 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Summit S-460, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Summit S-460, that we can find in the current document
3. Tips how to use the basic functions of the device Summit S-460 - which should help us in our first steps of using Summit S-460
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Summit S-460
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Summit S-460 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Summit S-460?

Use the form below

If you did not solve your problem by using a manual Summit S-460, ask a question using the form below. If a user had a similar problem with Summit S-460 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)