English dropdown-ico

Manual Toro 200

8 pages 0.55 mb
Download

Go to site of 8

Summary
  • Toro 200 - page 1

    Specifications: • Controls up to 200 stations for the Stand-Alone model • Input power supply 100 V AC, 50/60Hz 120 V AC, 50/60Hz 240 V AC, 50/60Hz • TDC output voltage: 40 V AC max. • TDC output power: 98V A max. • Storage temperature: -30C–60C • Operating temperature: 0–60C • Cabinet T ype: Non-corrosive, lockable wall mount, ind ...

  • Toro 200 - page 2

    Earth Ground Installation IMPORT ANT! The TDC surge protection components cannot properly function unless an ef ficient pathway to earth ground is provided. The ground path must be as direct as possible, without sharp bends and must not exceed 30 Ohm resistance (when measured with an earth ground resistance device). All electrical components throug ...

  • Toro 200 - page 3

    Power Source Installation Step 1 – T urn off the power at the power source location and place the controller ’s power switch to OFF . Connect and route the appropriate size 3-conductor cable (10 AWG [2.5mm 2 ] maximum) from the power source to the controller cabinet. The provided power cable access hole can accommodate a 1" (25mm) conduit ...

  • Toro 200 - page 4

    Station Decoder Installation The station decoder module is available in 1-station, 2-station or 4-station configuration. The decoder modules are installed into the TDC output board terminals. The stand-alone TDC model can handle up to 100 stations per output board. These stations can be connected to the output board terminals in any configuration ( ...

  • Toro 200 - page 5

    Paths – 1 23 4 V alve Box Maximum communication wire length between the controller and the farthest decoder is 15,000ft (4500m). Recommended Cable for Controller-to-Decoder is the Paige ® P7350D, 14 A WG, Solid Copper , Jacketed 2-Conductor, Direct Burial cable. White Black White Black White Black White Black The maximum communication wire lengt ...

  • Toro 200 - page 6

    Grounding Communication Cable IMPORT ANT! Cable Splices: In order for the wire connections to comply with the 2005 edition of the National Electric Code® Article 300.5 (Underground Installations) and 1 10.14 (Electrical Connections), in wet or damp locations, the connector must be listed under specification “UL 486D” if installed in a valve bo ...

  • Toro 200 - page 7

    Master V alve / Pump Relay Installation TDC provide switch terminals to control a master valve or a pump relay if the system requires it. Step 1 – Place the controller ’s power switch to OFF . Step 2 – Connect the Positive/Hot wire of the power source that controls the master valve or the pump relay to the Master valve/Pump relay switch termi ...

  • Toro 200 - page 8

    Lithium Battery Replacement A 3.9V Lithium battery (P/N 363-2200) is installed in the timing mechanism to sustain the controller ’s clock time and date for approximately 10-years with no additional power applied. Step 1 – Place the controller ’s power switch to OFF . Step 2 – Remove the ribbon cable from the rear of the timing mechanism. St ...

Manufacturer Toro Category Smoke Alarm

Documents that we receive from a manufacturer of a Toro 200 can be divided into several groups. They are, among others:
- Toro technical drawings
- 200 manuals
- Toro product data sheets
- information booklets
- or energy labels Toro 200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Toro 200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Toro 200, service manual, brief instructions and user manuals Toro 200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Toro 200.

Similar manuals

A complete manual for the device Toro 200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Toro 200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Toro 200.

A complete Toro manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Toro 200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Toro 200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Toro 200, that we can find in the current document
3. Tips how to use the basic functions of the device Toro 200 - which should help us in our first steps of using Toro 200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Toro 200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Toro 200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Toro 200?

Use the form below

If you did not solve your problem by using a manual Toro 200, ask a question using the form below. If a user had a similar problem with Toro 200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)