-
Ryobi SC164VS - page 1
SA VE THIS MANUAL FOR FUTURE REFERENCE OPERA TOR'S MANUAL 16 in. (406 mm) V ariable Speed SCROLL SA W Model SC164VS 0 30 15 THANK YOU FOR BUYING A RYOBI SCROLL SAW. Your new Scroll Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give ...
-
Ryobi SC164VS - page 2
Page 2 TABLE OF CONTENTS ■ Table of Contents .............................................................................................................. .............................. 2 ■ Introduction and Product Specifications ........................................................................................ .................. 2 ■ R ...
-
Ryobi SC164VS - page 3
Page 3 RULES FOR SAFE OPERA TION Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your scroll saw works. READ ALL INSTRUCTIONS ■ KNOW YOUR POWER TOOL. Read the operator's manual carefu ...
-
Ryobi SC164VS - page 4
Page 4 ■ AVOID AWKWARD OPERATIONS AND HAND POSI- TIONS where a sudden slip could cause your hand to move into the blade. ALWAYS make sure you have good balance. ■ ALLOW THE MOTOR TO COME UP TO FULL SPEED before starting a cut to avoid binding or stalling. ■ DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replace ...
-
Ryobi SC164VS - page 5
Page 5 RULES FOR SAFE OPERA TION GLASSES SAFETY WEAR YOUR FORESIGHT IS BETTER THAN NO SIGHT W ARNING: IMPORT ANT Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the tool to your nearest RYOBI AUTHORIZED SERVICE CENTER for repair. When servic- ing, use on ...
-
Ryobi SC164VS - page 6
Page 6 ELECTRICAL CONNECTION Your Ryobi Scroll Saw is powered by a precision built electric motor. It should be connected to a power supply that is 120 volts, 60Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the saw does n ...
-
Ryobi SC164VS - page 7
Page 7 Resin A sticky, sap base substance that has hardened. Ripping A cutting operation along the length of the workpiece. Saw Blade Path The area directly in line — over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be, or has been, cut by the blade. Set The distance that the tip of the saw blade ...
-
Ryobi SC164VS - page 8
Page 8 LOOSE P ARTS Check all loose parts from the box with the list below. Assemble according to the instructions on the following pages. • 3 mm T-Handle Hex Key • 4 mm Hex Key • Blade(s) • Plastic Tubing The following tools (not included) are needed for adjustments and alignment: • Combination Square • Phillips Screwdriver • Slotted ...
-
Ryobi SC164VS - page 9
Page 9 FEA TURES Sawdust Blower Keeps the line of the cut on the workpiece clean for more accurate scroll cuts. For best results, always direct air flow at the blade and the workpiece. Sawdust Exhaust This feature will allow you to attach any 1-1/4 in. (32 mm) vacuum hose for easy sawdust collection. Saw Table with Throat Plate Your scroll saw has ...
-
Ryobi SC164VS - page 10
Page 10 0 30 1 5 CLAMPING SCROLL SAW TO WORKBENCH See Figure 5. If the scroll saw is to be used in a portable application, it is recommended that you fasten it permanently to a mounting board that can easily be clamped to a workbench or other supporting surface. The mounting board should be of sufficient size to avoid tipping of saw while in use. A ...
-
Ryobi SC164VS - page 11
Page 11 0 30 15 ADJUSTMENTS W ARNING: To prevent accidental starting that could cause possible serious personal injury, turn off the saw and unplug the saw from the power source before making any adjustments. DROP FOOT See Figure 6. To prevent workpiece from lifting, the drop foot should be adjusted so it just rests on the top of the workpiece. The ...
-
Ryobi SC164VS - page 12
Page 12 SETTING THE TABLE FOR HORIZONTAL OR BEVEL CUTTING See Figure 8. W ARNING: Failure to turn the saw off, remove the switch key, and unplug the saw from the power source could result in accidental starting causing possible serious injury. A bevel scale is located under the saw table as a convenient guide for setting the approximate saw table a ...
-
Ryobi SC164VS - page 13
Page 13 ADJUSTMENTS INSTALLING BLADES Scroll saw blades wear out quickly and must be replaced frequently for best cutting results. Expect to break some blades while you learn to use and adjust your saw. Blades generally stay sharp for 1/2 hour to 2 hours of cutting, depending on the type of material and speed of operation. Pin End Blades See Figure ...
-
Ryobi SC164VS - page 14
Page 14 OPERA TION BASIC OPERATION OF THE SCROLL SAW Before starting a cut, watch the saw run. If you experience excessive vibration or unusual noise, stop immediately. Turn the saw off, remove the switch key, and unplug the saw. Do not restart until locating and correcting the problem. Note: After the saw is turned ON , a hesitation before blade m ...
-
Ryobi SC164VS - page 15
Page 15 OPERA TION Fig. 12 BLADE INFORMATION ■ Scroll saw blades wear out and must be replaced fre- quently for best cutting results. Scroll saw blades gener- ally stay sharp for 1/2 hour to 2 hours of cutting, depend- ing on type of material and speed of operation. ■ In cutting wood, best results are achieved when cutting wood less than one in ...
-
Ryobi SC164VS - page 16
Page 16 OPERA TION W ARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. W ARNING: To avoid possible serious injury from accidental starting, always turn the saw off, remove the switch key, and unplug the saw from power source before removing or r ...
-
Ryobi SC164VS - page 17
Page 17 W ARNING: When servicing, use only identical Ryobi replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL MAINTENANCE ■ Keep your scroll saw clean. ■ After cleaning the table top initially, apply a thin coat of automobile type (paste) wax to the table top so the wood slides easily while cutting. ? ...
-
Ryobi SC164VS - page 18
Page 18 TROUBLESHOOTING W ARNING: For your own safety, turn switch OFF and remove plug from power outlet before adjusting or aligning your scroll saw. MAINTENANCE W ARNING: To prevent accidental starting that could cause possible serious personal injury, turn off and unplug the saw before maintaining or lubricating your scroll saw. W ARNING: Failur ...
-
Ryobi SC164VS - page 19
Page 19 NOTES ...
-
Ryobi SC164VS - page 20
983000-0 46 9- 02 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com OPERA T OR'S MANUAL 16 in. (406 mm) V ariable Speed Scroll Saw Model SC164VS • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or s ...
Do you have a question concerning Ryobi SC164VS?
Use the form below
If you did not solve your problem by using a manual Ryobi SC164VS, ask a question using the form below. If a user had a similar problem with Ryobi SC164VS it is likely that he will want to share the way to solve it.