English dropdown-ico

Manual NuTone CV554

23 pages 1.36 mb
Download

Go to site of 23

Summary
  • NuTone CV554 - page 1

    Built-In Central Cleaning System MODELS: CV554, CV556, and CV570 SYSTEM PLANNING AND LAYOUT . . . . . . . . . . . . . . . . . . . . . . 2 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Locating the Power Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Tubing and Wall Inlet L ...

  • NuTone CV554 - page 2

    2 SYSTEM PLANNING AND LA YOUT The Nu T one Central Cleaning System consists of a Power Unit, PVC Tubing and Fittings, Wall Inlets, a flexible Hose and various cleaning Attachments. The Power Unit is designed to be wall-mounted away from the living area of the home and connected to the living area by means of permanently installed in-wall tubing, fi ...

  • NuTone CV554 - page 3

    3 • Locate the power unit away from the general living area in an accessible location for emptying the lower dirt cannister and periodically cleaning the filter. • When planning, remember the power unit is equipped with an inlet to service a garage, basement, utility room, etc., wherever it is located. • Locate the power unit within six feet ...

  • NuTone CV554 - page 4

    4 INST ALLA TION IN NEW CONSTRUCTION Once the locations for wall inlets have been determined, mount all inlet brackets. 1. Choose the appropriate mounting bracket for the inlet being installed. (See chart.) 2. To locate bracket on wall stud, measure approximately 18" up from finished floor level. (Height may vary according to individual prefer ...

  • NuTone CV554 - page 5

    5 INST ALLA TION IN NEW CONSTRUCTION (continued) Use the following installation guidelines when installing tubing. 1. Start tubing installation at farthest inlet and work toward the power unit. 2. Tubing run to the power unit should be as straight as possible. 3. When assembling sections with elbows and tees, make sure the curve in the fitting is a ...

  • NuTone CV554 - page 6

    6 INST ALLA TION IN NEW CONSTRUCTION (continued) FIGURE 19 FIGURE 21 MODEL 365 DOUBLE FLANGED TEE W ALL INLET MOUNTING BRACKET SHORTEN W ALL FIGURE 17 MODEL 360 WALL INLET (361 Rough-In) 1. Remove the cardboard plaster guard. 2. Refer to Figure 17. For some drywall or panel construction, the plaster frame will extend beyond the finished wall. In th ...

  • NuTone CV554 - page 7

    7 INST ALLA TION IN NEW CONSTRUCTION (continued) 1. See Figure 23. Fasten the mounting plate to a stud within three studs (48") of an electrical outlet box. Measure and mark the wire 10" from the plug (A). Feed the wire through the top hole in the mounting plate (just above the circular opening). Snap the molded plug into the mounting pla ...

  • NuTone CV554 - page 8

    8 1. Use black rubber connectors and hose clamps to connect intake and exhaust tubing. 2. Connect intake tubing to intake tube on power unit. 3. Connect exhaust tubing to upper exhaust tube on power unit. 4. Make sure all tubing connections are securely fastened. 5. An optional muffler (Model 392) may be installed to reduce motor noise. 6. The exha ...

  • NuTone CV554 - page 9

    9 Use the following procedures for installation in existing construction. Starting from farthest wall inlet location, install each inlet as described below. Working back toward power unit, connect each inlet line and branch line into main trunk line. See page 5. Complete low voltage wiring as main trunk line is continued back to power unit. Mount p ...

  • NuTone CV554 - page 10

    10 INST ALLA TION IN EXISTING CONSTRUCTION (continued) MOUNTING PLA TE MOUNTING HOLE (2) ELBOW FIGURE 36 MOUNTING PLA TE INLET FIGURE 37 1. Make cutout according to dimensions in Figure 34. 2. Refer to Figure 35. Break off nail plate at scored line. 3. Refer to Figure 36. Glue elbow to mounting plate, place assembly into cutout, and attach elbow to ...

  • NuTone CV554 - page 11

    11 FLOOR INLET INST ALLA TION FLOOR SUB-FLOOR 2 9 / 16 " 3 1 / 16 " INLET EXTENSION FLOOR INLET FRAME MOUNTING BRACKET SEAL FLANGED FITTING FIGURE 40 CUT TO LENGTH EXTENSION SLEEVE FLANGED FITTING MOUNTING BRACKET FLANGE FIGURE 41 W ALL INLET EXTENSION SLEEVE BRACKET FLANGED FITTING TUBING FIGURE 42 FINAL SYSTEM CHECK Be sure all inlets a ...

  • NuTone CV554 - page 12

    Systè me Central PLANIFICATION ET DISPOSITION DU SYSTEME . . . . . . . . . . . 2 Exemples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Emplacement du Groupe d’Aspiration . . . . . . . . . . . . . . . . . . . . . .3 Tuyauterie et Emplacement des Prises Murales . . . . . . . . . . . . . .3 Emplacement de ...

  • NuTone CV554 - page 13

    2 PLANIFICA TION ET DISPOSITION DU SYSTEME Le système central d'aspiration intégré de NuTone comprend un groupe d'aspiration, une tuyauterie et des raccords en PVC, des prises d'aspiration murales, un tuyau souple et de différents accessoires de nettoyage. Le Groupe d'Aspiration est conçu pour un montage mural éloigné de ...

  • NuTone CV554 - page 14

    3 • Installez le groupe d’aspiration à l’écart de la zone habitée, à un endroit facile d’accès pour le nettoyage du filtre et la vidange du bac à saleté. • Lors de votre planification, rappelez-vous que le groupe d'aspiration est équipé d'une prise pour vous servir dans le garage, le sous-sol, la buanderie, etc., où qu ...

  • NuTone CV554 - page 15

    4 INST ALLA TION DANS UNE NOUVELLE CONSTRUCTION Une fois l'emplacement des prises murales déterminé, mettez en place tous les supports de prise. 1. Choisissez les supports de fixation appropriés pour la prise à installer. (Voyez le tableau). 2. Pour positionner le support sur le montant, mesurez approximativement 45,7 cm au-dessus du nivea ...

  • NuTone CV554 - page 16

    5 INST ALLA TION DANS UNE NOUVELLE CONSTRUCTION (suite) Suivez les lignes directrices ci-dessous lors de la mise en place de la tuyauterie. 1. Commencez l'installation de la tuyauterie par la prise la plus éloignée et avancez vers le groupe d'aspiration. 2. La tuyauterie qui rejoint le groupe d'aspiration devrait être la plus droi ...

  • NuTone CV554 - page 17

    6 INST ALLA TION DANS UNE NOUVELLE CONSTRUCTION (suite) FIGURE 19 FIGURE 21 MODEL 365 DOUBLE FLANGED TEE W ALL INLET MOUNTING BRACKET SHORTEN W ALL FIGURE 17 MODELE 360 PRISE MURALE (ENCASTREMENT 361) 1. Enlevez le carton du cadre protecteur. 2. Voyez la figure 17. Pour certaines cloisons sèches ou constructions à panneaux, le cadre va s'ete ...

  • NuTone CV554 - page 18

    7 INST ALLA TION DANS UNE NOUVELLE CONSTRUCTION (suite) 1. Voyez la figure 23. Attachez la plaque de montage à un montant à une distance maximum de trois montants (1,22 m) d'un coffret de sortie électrique. Mesurez et marquez le câble à 25,4 cm de la prise (A). Avancez le câble à travers le trou du haut de la plaque de montage juste au- ...

  • NuTone CV554 - page 19

    8 1. Utilisez des raccords de caoutchouc noir et des brides pour connecter les conduites d'arrivée et d'évacuation. 2. Raccordez la conduite d'arrivée à l'entrée du groupe d'aspiration. 3. Raccordez la conduite d'évacuation à l'échappement supérieur du groupe d'aspiration. 4. Assurez-vous que tous le ...

  • NuTone CV554 - page 20

    9 Utilisez les procédures suivantes pour une installation dans une construction existante. En commençant par la prise murale la plus éloignée, installez chaque prise tel qu' il vous est décrit ci-dessous. Travaillez vers le groupe d'aspiration; connectez chaque ligne de prise et ligne secondaire à la ligne principale. Voyez la page ...

  • NuTone CV554 - page 21

    10 INST ALLA TION DANS UNE CONSTRUCTION EXIST ANTE (suite) MOUNTING PLA TE MOUNTING HOLE (2) ELBOW FIGURE 36 MOUNTING PLA TE INLET FIGURE 37 1. Faites la découpe en accord avec les dimensions de la Figure 35. 2. Voyez la Figure 36. Détachez la plaque suivant les pointillés. 3. Voyez la Figure 37. Collez le coude à la plaque de montage, placez l ...

  • NuTone CV554 - page 22

    11 INST ALLA TION DES PRISES AU SOL FLOOR SUB-FLOOR 2 9 / 16 " 3 1 / 16 " INLET EXTENSION FLOOR INLET FRAME MOUNTING BRACKET SEAL FLANGED FITTING FIGURE 40 CUT TO LENGTH EXTENSION SLEEVE FLANGED FITTING MOUNTING BRACKET FLANGE FIGURE 41 W ALL INLET EXTENSION SLEEVE BRACKET FLANGED FITTING TUBING FIGURE 42 VERIFICA TION FINALE DU SYSTEME A ...

  • NuTone CV554 - page 23

    4820 Red Bank Road, Cincinnati, Ohio 45227 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9 www.nutone.com T wo Y ear Limited W arranty WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of two (2) years from the date of ori ...

Manufacturer NuTone Category Vacuum Cleaner

Documents that we receive from a manufacturer of a NuTone CV554 can be divided into several groups. They are, among others:
- NuTone technical drawings
- CV554 manuals
- NuTone product data sheets
- information booklets
- or energy labels NuTone CV554
All of them are important, but the most important information from the point of view of use of the device are in the user manual NuTone CV554.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals NuTone CV554, service manual, brief instructions and user manuals NuTone CV554. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product NuTone CV554.

Similar manuals

A complete manual for the device NuTone CV554, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use NuTone CV554 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of NuTone CV554.

A complete NuTone manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual NuTone CV554 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the NuTone CV554, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the NuTone CV554, that we can find in the current document
3. Tips how to use the basic functions of the device NuTone CV554 - which should help us in our first steps of using NuTone CV554
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with NuTone CV554
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of NuTone CV554 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning NuTone CV554?

Use the form below

If you did not solve your problem by using a manual NuTone CV554, ask a question using the form below. If a user had a similar problem with NuTone CV554 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)