English dropdown-ico

Manual GBC USP 13

17 pages 2.27 mb
Download

Go to site of 17

Summary
  • GBC USP 13 - page 1

    USP 13 UNIVERSAL SPEED PUNCH Operator Manual ...

  • GBC USP 13 - page 2

    USP 13 UNIVERSAL SPEED PUNCH Operator Manual T able of Contents Operating Instructions 1 Service and Maintenance Agreement 2 Selecting Knife Set Up 3 Installation of Punching Die 4 Set Up Instructions 5 Quick Reference Instructions 8 Maintenance Instructions 9 General Rules for Grinding Pins 10 Options and Accessories 11 ...

  • GBC USP 13 - page 3

    USP 13 Universal Speed Punch Operating Instructions The Universal Speed Punch from GBC Automated Finishing Division is specially designed to punch various weight paper sheets and cover stock. The machine has a variable speed control which can be adjusted from 70-110 cycles per minute. The thickness of individual layers being punched is adjustable, ...

  • GBC USP 13 - page 4

    Service And Equipment Maintenance Agreement By purchasing the USP 13 you have invested in a highly capable punching machine that will give you years of r eliable service. T o help protect this investment be certain to take advantage of the GBC Equipment Maintenance Agr eement (EMA). The EMA provides your USP 13 with pr oper ongoing maintenance and ...

  • GBC USP 13 - page 5

    3 SELECTING KNIFE SET -UP 1. T ur n power off. 2. Cycle the machine with the hand wheel until the claw reaches between 10 and 11 o’clock. (Figur e 2) 3. Cam #115 sets when the separating knife will go into the stack. Adjust the cam so that the tip of the knife is about 1/8” (.13) from the trailing edge of the claw . (Figure 2) 4. Cam #36 sets w ...

  • GBC USP 13 - page 6

    USP 13 Installation of Punching Dies Using Quick Release Die Clamp Assembly When installing a punching die, be sure that the lower die support is wiped clean of dirt and paper chips. The bottom of the die itself should be cleaned likewise. Wiping the top and bottom of the die with a thin coating of oil is advisable. Place the die into the machine a ...

  • GBC USP 13 - page 7

    5 USP 13 SET -UP INSTRUCTIONS: After the punching die is properly installed, position the back gauge rail (#108, Figure 7) slightly ahead of the punch die back gauge so that a piece of paper can slide freely into the thr oat of the die and not hit the back gauge of the punch die. Cam (#37) activates the rear jogger (#34) and the side jogger (#29). ...

  • GBC USP 13 - page 8

    111 170 83 127 1.0 Figure 10 Figure 12 CLA W THESE SURF ACES TO BE IN LINE 46 Place a sheet of paper against pusher (#111) in its home position (rear). Install the thr ee paper support straps (#127 & #83, Figure 10) 1” away fr om the edge of the paper . Straps must be on top of transfer belts. Cycle the machine by hand until the pusher has pu ...

  • GBC USP 13 - page 9

    7 Position front (#49) and r ear (#56 & #48) supply stack guides so that the posts clear the paper stack by about 1/16”. A stack of 2 to 3 inches is requir ed. Locate adjustable stack guide post (#59) so that the post is in line with the separating knife. (Figure 13). Install front guide rail (#55) so that ther e is about 1/8” to 1/4” cle ...

  • GBC USP 13 - page 10

    USP 13 Universal Speed Punch QUICK REFERENCE INSTRUCTIONS 1. DIE REPLACEMENT BLOCK UP DIE WITH STICK PROVIDED LOWER DIE CLAMP STICK REMOVE DIE CLAMPS - FRONT & REAR REMOVE BOTTOM BOL TS RELEASE CLAMP - RELAX PRESSURE WITH HAND WHEEL SLIDE DIE OUT REPLACE DIE WITH STICK IN PLACE REPLACE BOTTOM BOL TS LOOSEL Y A TT ACH CLAMPS TIGHTEN BOL TS REMOV ...

  • GBC USP 13 - page 11

    9 It is recommended that the machine be lubricated once every two weeks. Lubricate by putting a few drops of machine oil in the lubricating holes, which are marked with red paint. All gears in the main body of the machine run in pans, which are partially filled with a special gear lubricating grease. This gr ease should be replenished occasionally ...

  • GBC USP 13 - page 12

    10 GENERAL RULES FOR GRINDING PUNCHING PINS OF PUNCHING TOOLS IT IS ALSO NECESSAR Y TO SHARPEN THE FEMALE PORTION (BOTTOM PLA TE) OF THE PUNCHING TOOL. SURF ACE GRIND THE TOP OF THE BOTTOM PLA TE UNTIL THE EDGES OF THE HOLES ARE SHARP . THIS WILL REQUIRE APPROXIMA TEL Y .005” OF STOCK REMOV AL. NOTE: IF THE PINS ARE SHARPENED EVER Y 100 HOURS, TH ...

  • GBC USP 13 - page 13

    11 USP 13 OPTIONS & ACCESSORIES 1. Short Sheet Assembly 2. Front and Rear Cradle Bracket Assemblies 3. Long Small Roller Assembly 4. Stack Guider Adaptor 5. Auxiliary Pusher Optional assemblies that can be purchased separately include: 1. Small Roller Assembly 2. Small Sheet Jog Adaptor 3. T abbed Stock Jog Adaptor R.H. 0165036200 + L. H. 01650 ...

  • GBC USP 13 - page 14

    12 ...

  • GBC USP 13 - page 15

    13 016509000 LONG SMALL ROLLER ASSEMBL Y The Long Small Roller Assembly is used when the standard Large Roller Assembly does not allow enough reach to grab a lift of paper when it is fully jogged. ...

  • GBC USP 13 - page 16

    14 ...

  • GBC USP 13 - page 17

    General Binding Corporation Northbr ook, Il 60062-4195 http://www .GBC.com PN 0165999900 Rev B ...

Manufacturer GBC Category Time Clock

Documents that we receive from a manufacturer of a GBC USP 13 can be divided into several groups. They are, among others:
- GBC technical drawings
- USP 13 manuals
- GBC product data sheets
- information booklets
- or energy labels GBC USP 13
All of them are important, but the most important information from the point of view of use of the device are in the user manual GBC USP 13.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GBC USP 13, service manual, brief instructions and user manuals GBC USP 13. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GBC USP 13.

Similar manuals

A complete manual for the device GBC USP 13, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GBC USP 13 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GBC USP 13.

A complete GBC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GBC USP 13 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GBC USP 13, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GBC USP 13, that we can find in the current document
3. Tips how to use the basic functions of the device GBC USP 13 - which should help us in our first steps of using GBC USP 13
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GBC USP 13
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GBC USP 13 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GBC USP 13?

Use the form below

If you did not solve your problem by using a manual GBC USP 13, ask a question using the form below. If a user had a similar problem with GBC USP 13 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)