Manual Sanyo MPR-1411R

41 pages 0.98 mb
Download

Go to site of 41

Summary
  • Sanyo MPR-1411R - page 1

    - 38 - - 38 - MPR-141 1 MPR-141 1R Pharmaceutical Refrigerator INSTRUCTION MANUAL MPR-141 1R ...

  • Sanyo MPR-1411R - page 2

    - 39 - - 39 - 1 CONTENTS I N T R O D U C T I O N P . 2 PRECAUTIONS FOR SAFE OPERATION P. 3 ENVIRONMENTAL CONDITIONS P. 7 REFR IGER ATOR CO MPONEN TS P. 8 Control panel P. 10 Inside of front cover P. 11 INSTALLATION SITE P. 12 INSTALLATION P. 13 START-UP OF UNIT P. 14 STOCK OF CONTAINERS P. 15 CHAMBER TEMPERATURE SETTING P. 16 ALARM TEMPERATURE SETT ...

  • Sanyo MPR-1411R - page 3

    - 40 - - 40 - 2 INTRODUCTION Ŷ Read this manual caref ully before using the appliance and follow the inst ructions for safety operation. Ŷ Sanyo never guarantee any safety if the ap pliance is used for any obje cts other than intended use o r used by any procedures other than those mentioned in this manual. Ŷ Keep this manual in an adequate plac ...

  • Sanyo MPR-1411R - page 4

    - 41 - - 41 - 3 PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with this manual as it contains important safety advice. Items and procedures are described so that you can use this unit correctly and safely. If the precautions advised are followed, this will prevent possible injury to the user and any other person. Precaution ...

  • Sanyo MPR-1411R - page 5

    - 42 - - 42 - 4 PRECAUTIONS FOR SAFE OPERATION Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to rain water. Only qualified engineers or serv ice personnel should install the unit. The installation by unqualified personnel may cause electric shock o r fire. Install the unit on a sturdy floor and ta ...

  • Sanyo MPR-1411R - page 6

    - 43 - - 43 - 5 PRECAUTIONS FOR SAFE OPERATION Ensure you do not inhale or consume medication or aero sols from around the unit at the time of maintenance. These may be harmful to your health. Never splash water directly onto the unit as this may cau se electric shock or short ci rcuit. Never put containers with liquid on the unit as thi s may cau ...

  • Sanyo MPR-1411R - page 7

    - 44 - - 44 - 6 PRECAUTIONS FOR SAFE OPERATION Use a dedicated po wer source (a dedicated ci rcuit with a breaker) a s indicated on the ra ting label attached to the unit. A branched circuit may cause fire resulting from abnormal heating. Connect the po wer supply plug to the power source firmly after remov ing the dust on the plug. A dusty plug or ...

  • Sanyo MPR-1411R - page 8

    - 45 - - 45 - 7 ENVIRONMENTAL CONDITIONS This equipment is designe d to be safe at least under the following condition s (based on the IEC 61010-1): 1. Indoor use; 2. Altitude up to 2000 m; 3. Ambient temperature 5 o C to 40 o C 4. Maximum relative humidity 80% for temperature up to 31 o C decre asing linearly to 50% relative humidity at 40 o C; 5. ...

  • Sanyo MPR-1411R - page 9

    - 46 - 8 REFRIGERATOR COMPONENTS 13 4 1 5 7 8 3 9 2 12 11 10 MPR-1411R MPR-1411 14 15 6 Rear side 17 18 12 16 ...

  • Sanyo MPR-1411R - page 10

    - 47 - 9 REFRIGERATOR COMPONENTS 1. Front cover: A front cover opens when a bottom part is pulled to the front. Open this cover when you use cleaning of the conden ser filter, a remote alarm terminal. Refer to page 11. 2. Control panel: Panel opens when the right top of the lowe r part cover is pushed. Refer to page 10. 3. Light switch: This switch ...

  • Sanyo MPR-1411R - page 11

    - 48 - 10 REFRIGERATOR COMPONENTS Control panel 1. Door check indicator (DOOR): The red LED lamp is lit when th e outer door is opened. 2. Alarm lamp (ALARM): This lamp is flashed when the audible alarm is activated. 3. Digital temperature indicator: This indicato r shows the present cha mber temperature or set temperature. 4. Numerical value shift ...

  • Sanyo MPR-1411R - page 12

    - 49 - 11 REFRIGERATOR COMPONENTS Inside of front cover 1. Condenser filter: This filter is for prevention of condenser clogged up. Clean the filter every 3 month. 2. Remote alarm terminal: This is used to connect the unit to an exterior alarm to notify users of any malfunction. Refer to page 21. 3. Glow starter: This is for the fluorescent lamp. I ...

  • Sanyo MPR-1411R - page 13

    - 50 - 12 INSTALLATION SITE To operate this unit properly and to obtain maximum performance, install the unit in a location with the following conditions: Ŷ A location not compliance with the following condition s may cause poor performance, failure or accident. Ŷ A location not subjected to direct sunlight Do not install the unit under direct su ...

  • Sanyo MPR-1411R - page 14

    - 51 - 13 INSTALLATION 1. Removing the packaging materials and tape s Remove all transportation packagi ng materials and tapes. Open the doors and ventilate the unit. If the outside panels are dirty, clean them with a diluted neutral dishwashing detergent. (Undiluted detergent can damage the pla stic components. For the dilution, refer to the instr ...

  • Sanyo MPR-1411R - page 15

    - 52 - 14 START-UP OF UNIT Follow the procedures for the initial and con sequent operations of the unit.   1. Connect the power cord to the dedicated outlet with appropriate rating. CAUTION If the unit is unplugged or the power to the unit is interrupted, do not restart the unit for at least 5 minutes. This protects the compressor. 2. On star ...

  • Sanyo MPR-1411R - page 16

    - 53 - 15 STOCK OF CONTAINERS Always distribute items so as not to disturb the a ir circulation in the cham ber. Disruption of the air flow can cause items to freeze or r educe the uniformity of the chamber temper ature. Never put any articles on the top of the unit. Intake air vent Do not block this vent with containers. If this vent becomes block ...

  • Sanyo MPR-1411R - page 17

    - 54 - 16 CHAMBER TEMPERATURE SETTING Table 1 shows the basic p rocedure for setting the chamber tem perature. Perform key operations in the sequence indicated in th e table. The example in the table is based on the assumption that the desi red temperature is 10 o C. Note: The unit is set at the factory with a chamber temperature of 5 o C. Table 1 ...

  • Sanyo MPR-1411R - page 18

    - 55 - 17 ALARM TEMPERATURE SETTING This unit is provided with both high a nd low temperature alarm s. The temperature at which the alarm is activated may be changed. The available set range for high temperature alarm is between +2 o C and +14 o C and -2 o C and -14 o C for low temperature alarm a gainst the chamber temperature. Note: The temperatu ...

  • Sanyo MPR-1411R - page 19

    - 56 - 18 SETTING OF DELAY OF DOOR ALARM The door check indicator is light when the door is ope ned, and the alarm buzzer sound s with some delay to notice the door opening. The delay time (between lighting of the door check indicator and activation of the alarm buzzer) can be changed. Set an appropriate delay time according to the conditio n of us ...

  • Sanyo MPR-1411R - page 20

    - 57 - 19 SETTING OF ALARM RESUME TIME The alarm buzzer and remote alarm are silenced by pressing h e alarm buzzer stop key (B UZZER) on the control panel during alarm con dition. The buzzer and remote alarm will be activated again after certain suspension if the alarm condition i s continued. The suspen sion time can be set by followi ng the proce ...

  • Sanyo MPR-1411R - page 21

    - 58 - 20 KEY LOCK FUNCTION This unit is provided with a key lock function. When the key lock is ON, change of temperature setting through the key pad is not available. The key lock is set in OFF at the factory. Display Mode Function L0 Key lock is OFF Enable to change of temperature setting L1 Key lock is ON Disable to change of temperature settin ...

  • Sanyo MPR-1411R - page 22

    - 59 - 21 DEFROST CYCLES 㩵 Cycle defrost When the ambient humidity is high, or a large amount of damp product is being stored inside the chambe r, there is a possibility that cycle defrost may not be enough to remov e all of the frost on the evaporator. In this case, a forced defrost cycle can be initiated. 㩵 Forced defrost When the unit is ope ...

  • Sanyo MPR-1411R - page 23

    - 60 - 22 ALARMS & SAFETY FUNCTIONS This unit has the alarms and safety funct ions shown in Table 7, and also self diagnostic functions. Table 7 Alarms and safety functions Alarm & Safety Situation Indication Buzzer Safety operation High temperature alarm If the chamber temperatur e deviates from the set temperature +2 o C or up to +14 o C. ...

  • Sanyo MPR-1411R - page 24

    - 61 - 23 ROUTINE MAINTENANCE WARNING Always disconnect the po w er supply to the unit prior to any repair or maintenance of the unit in order to prevent electric shock or injury . Ensure you do not inhal e or consume medication or aeros ols from around the unit at the time of maintenance. These may be harmful to your health. CAUTION Always wear dr ...

  • Sanyo MPR-1411R - page 25

    - 62 - 24 ROUTINE MAINTENANCE Replacement of fluorescent lamp The fluorescent lamp is placed vertically at the cente r of the chamber. Follow the procedure below to replace the lamp. 1. Turn off the fluorescent light switch and di sconnect the power supply plug. 2. Remove all shelves or drawe rs. 3. In the case of MPR-1411R, remove the rail that is ...

  • Sanyo MPR-1411R - page 26

    - 63 - 25 ROUTINE MAINTENANCE Replacement of glow starter A glow starter is located inside the front cover. 1. Disconnect the power supply plug. 2. Remove the water-proof rubb er. 3. Remove the glow starter and repla c e with a new on e. 4. Replace the water-pro of rubber. Cleaning of condenser filter 1. Lift the front cover as shown in the figure. ...

  • Sanyo MPR-1411R - page 27

    - 64 - 26  TROUBLE SHOOTING   If the unit malfunctions, check out the following before calling for service. Malfunction Check/Remedy If nothing operates even when switched on 㩵 There is a power failure. 㩵 The circuit breaker is activated. 㩵 The unit is not connected to the power su pply. When no key operation is available 㩵 T ...

  • Sanyo MPR-1411R - page 28

    - 65 - 27 DISPOSAL OF UNIT WARNING If the unit is to be stored unused in an unsupervised area for an extended pe riod ensure that children do not have access and doors canno t be closed completely. The disposal of the unit should be accomplished by appropriate perso nnel. Always remove doors to prevent accidents such as suffocation. ...

  • Sanyo MPR-1411R - page 29

    - 66 - 28 DISPOSAL OF UNIT (English) FOR EU USERS The symbol mark and recycling systems described below apply to EU countries and do not apply to countries in other areas of the wo rld. Your SANYO product is d esigned and manufa ctured with high quality material s and components which can be recycled and/or re used. The symbol mark means that elect ...

  • Sanyo MPR-1411R - page 30

    - 67 - 29 DISPOSAL OF UNIT (French) POUR LES UTILISATEURS DE UE Le symbole et les système s de recyclage évoqués ci-desso us s'appliquent uniquement aux pays de UE. Votre produit SANYO est conçu et fabriqué avec des com posants et des matériaux de hautes qualités qui peuvent être recyclés et/ou réutilisés. Le symbole signifie que le ...

  • Sanyo MPR-1411R - page 31

    - 68 - 30 DISPOSAL OF UNIT (Portuguese) PARA UTILIZADORES DA UE O símbolo e os sistem as de reciclagem descritos abaixo apli cam-se aos países da UE e não se aplica m aos países noutras área s do mundo. O seu produto SANYO foi concebido e fabrica do com materiais e compone ntes de elevada qualidade que podem ser reci clados e/ou reutilizados. ...

  • Sanyo MPR-1411R - page 32

    - 69 - 31 DISPOSAL OF UNIT (Dutch) VOOR GEBRUIKERS IN DE EU Het symbool en de re cycleersystemen die hierond er beschreven worden, zijn van toepa ssing op de landen in de EU en zijn niet van toepassing o p landen in andere delen van de wereld. Uw SANYO product is ontworpen en gemaakt met materialen en onderdele n van hoge kwaliteit, die gerecycleer ...

  • Sanyo MPR-1411R - page 33

    - 70 - 32 OPTIONAL COMPONENTS Automatic temperature recorder An automatic temperature recorder is available for this refrigerator as an optional accessory. If an automatic temperature recorder is required, contact your Sanyo deale r. Two recorder s are selectable for th e refrigerator; MTR-0621LH and MTR-G04. Please note that each recorder needs a ...

  • Sanyo MPR-1411R - page 34

    - 71 - 33 OPTIONAL COMPONENTS 6. An attached binder (two pcs) is used for the fan c over of the top of the chamber a s the Fig. 5, and a temperat ure sensor is fixed. 7. Route the capillary on the top of the cha mber and fix it with the provided clip and screw. (Fig. 6) 8. Make a cut on the rubber caps so that the capillary can pass the caps and pl ...

  • Sanyo MPR-1411R - page 35

    - 72 - 34 OPTIONAL COMPONENTS 3. Remove the black rub ber caps (inside and outside) on the access port located at the top corner of the unit and take the insulation out of the access port. 4. Pass the recorder sensor into the chamber throu gh the access port. (Fig. 3) 5. An attached binder (two pcs) is u sed for the fan cover of the top of the cham ...

  • Sanyo MPR-1411R - page 36

    - 73 - 35 OPTIONAL COMPONENTS Attachment of battery kit MPR-48B The alarm lamp blinks an d the alarm buzzer sounds to notice the power failure whe n a battery for power failure alarm is installed. For the installation of the battery for power failure alarm, a battery kit (MPR-48B), an optional component is necessary. A battery for power failure ala ...

  • Sanyo MPR-1411R - page 37

    - 7 4 - 36 OPTIONAL COMPONENTS 5. Put the battery fixture over the battery and fix the battery box and battery fixture by four screws. (Fig. 4) 6. Each harness is connected to the battery connecto rs (Fig. 5) and switche s to a fixed mounting plate on the battery clip.(Fig. 4) 6. Connect the harness to the battery conne ctor and battery switch (Fig ...

  • Sanyo MPR-1411R - page 38

    - 75 - 37 OPTIONAL COMPONENTS Setting for battery before starting Always perform the setting shown below after the inst allation of battery for power failure alarm, an optional component (MPR-48B). The chamber temperature and “E09” is displayed on the temperature display alternately if the battery switch is turned on without following procedure ...

  • Sanyo MPR-1411R - page 39

    - 7 6 - 38 SPECIFICATIONS   Name  Pharmaceutical Refrigerator  Model  MPR-1411 MPR-1411R External dimensions  W1440 x D830 x H1950 (mm) Internal dimensions  W1320 x D710 x H1500 (m m) Effective capacity  1364 L 1359 L Exterior  Painted steel  Interior  Painted steel  Door  Double layer pair glass/ste el plate, ...

  • Sanyo MPR-1411R - page 40

    - 77 - 39 CAUTION Please fill in this form before servicing. Hand over this form to the service engineer to keep for his and your safety. Safety check sheet 1. Refrigerator contents : Risk of infection: Risk of toxicity: Risk from radioactive sources: (List all potentially hazardous materials that have been stored in this un it.) Notes : 2. Contami ...

  • Sanyo MPR-1411R - page 41

    SANYO Electric Co., Ltd Printed in Japan ...

Manufacturer Sanyo Category Refrigerator

Documents that we receive from a manufacturer of a Sanyo MPR-1411R can be divided into several groups. They are, among others:
- Sanyo technical drawings
- MPR-1411R manuals
- Sanyo product data sheets
- information booklets
- or energy labels Sanyo MPR-1411R
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sanyo MPR-1411R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sanyo MPR-1411R, service manual, brief instructions and user manuals Sanyo MPR-1411R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sanyo MPR-1411R.

Similar manuals

A complete manual for the device Sanyo MPR-1411R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sanyo MPR-1411R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sanyo MPR-1411R.

A complete Sanyo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sanyo MPR-1411R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sanyo MPR-1411R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sanyo MPR-1411R, that we can find in the current document
3. Tips how to use the basic functions of the device Sanyo MPR-1411R - which should help us in our first steps of using Sanyo MPR-1411R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sanyo MPR-1411R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sanyo MPR-1411R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sanyo MPR-1411R?

Use the form below

If you did not solve your problem by using a manual Sanyo MPR-1411R, ask a question using the form below. If a user had a similar problem with Sanyo MPR-1411R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)