-
Siemens ANIM-03114 - page 1
ANIM-03114 (03/02) (Supersedes all pre vious issues) ©2002 Siemens Energy & Automation, Inc. All rights reser ved. Storage Recommendations Induction Motors/ Generators ...
-
Siemens ANIM-03114 - page 2
- 1 - Table of Contents Page Safety Procedures………………… …………………………… 2 Introduction………………………… …………………………… 3 Indoor Storage (Up to 5 Years) Wholly Controlled Atmosphere………………………………... 4 Partially Controlled Atmosphere…………………………… ? ...
-
Siemens ANIM-03114 - page 3
- 2 - Safety Procedures This equipment contains haza rdous voltages. Death, serious personal inju ry or property damage can resu lt if safety instructions are not followed. The successful and safe ope ration of motors and generators is depend ent upon proper handling, installation, operation and mainte nance, as well as upon proper design and manuf ...
-
Siemens ANIM-03114 - page 4
- 3 - Introduction The purpose of this booklet is to offer some short, easy to follow recommendations to our customers, users and distributors for the care of electri c motors in storage. For prac tical purposes , such equipm ent is conside red to be in storage not only when it is in the storeroom but also when; 1. It has been delivered to the jobs ...
-
Siemens ANIM-03114 - page 5
- 4 - Indoor Storage (Up to 5 Years) NOTE Rodents and other animals in search of warm surroundings or food, like to house insid e motors. Some of them attack the insulation ma terials. Their access to the motor should be prevented. Wholly Controlled Atmosphere Requirements Uniform temperature between 40°F (4.5°C) and 140°F (60° C) throughout th ...
-
Siemens ANIM-03114 - page 6
- 5 - Outdoor Storage (Up to 5 Years) NOTE Rodents and other animals in search of warm surroundings or food, like to house insid e motors. Some of them attack the insulation ma terials. Their access to the motor should be prevented. Inland Dry Climate Conditions Usually Encountered Dust, sand, heat from the sun, and occasional rain o r snow. Requir ...
-
Siemens ANIM-03114 - page 7
- 6 - Outdoor Storage (Up to 5 Years) NOTE Rodents and other animals in search of warm surroundings or food, like to house insid e motors. Some of them attack the insulation ma terials. Their access to the motor should be prevented. Inland Humid Climate: (Non Industrial Area) Conditions Usually Encountered Dust, rain, snow, organic g rowth (fungus) ...
-
Siemens ANIM-03114 - page 8
- 7 - Outdoor Storage (Up to 5 Years) NOTE Rodents and other animals in search of warm surroundings or food, like to house insid e motors. Some of them attack the insulation ma terials. Their access to the motor should be prevented. Salty and Industrial Atmospheres Conditions Usually Encountered Moisture impregnated with salts or other chemicals, s ...
-
Siemens ANIM-03114 - page 9
- 8 - Preparation For Storage CAUTION Moisture. Can damage windings. Protect motor from moisture. Sleeve and Tilting Pad Bearings Motors with this type of bearing are shipped without lubri cati ng oil. A film of rust-inhibiting oil from factory testing protects the bearing and sh aft journals during shipme n t, but this protection does not last lon ...
-
Siemens ANIM-03114 - page 10
- 9 - Preparation For Storage Shaft Extensions and Exposed Ma chined Surfaces Surfaces should be coated with an easil y remov able rust preventive such as Tectyl No. 502-C. If the storage period will be nine months or longer and the risk of exposure to moisture is present, take the following pr ecautions; 1. Before adding the lubricant described a ...
-
Siemens ANIM-03114 - page 11
- 10 - Maintenance During Storage DANGER Hazardous voltage. Can cause death, severe injury, or property damage. Follow all safety rules. Sleeve Bearings Per Chart 1, the motor shaft should b e manually rotate d by hand at about 30 rpm for 15 seconds or if power is available, the motor can be electrically b umped for 5 seconds; Chart 1 STORAGE ENVIR ...
-
Siemens ANIM-03114 - page 12
- 11 - Maintenance During Storage Oil Mist Lubricated Anti-F riction Bearings If motor was shipped with grease in the bearing, follow in structions for grease lubricated anti-friction b earings described above. If motor does not have grease in the bearing, start the o il mist system connected during the storage preparations, start the motor, and ru ...
-
Siemens ANIM-03114 - page 13
- 12 - Preparation For Service Cleaning Both the interior and exterior of the m otor should be free of spilled oil, water, dust, and dirt. The exterior should be wiped a nd the interior b lown out with compressed air at a reduced pre ssure. CAUTION Moisture. Can damage windings. Protect motor from moisture. Wipe off removable rust preventatives wit ...
-
Siemens ANIM-03114 - page 14
- 13 - Notes ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ______________ ...
-
Siemens ANIM-03114 - page 15
- 14 - Notes ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ___________________ __________________ _______________ _____ ___________________ ______________ ______________ ...
-
Siemens ANIM-03114 - page 16
ANIM-03114 (03/02) (Supersedes all pre vious issues) ©2002 Siemens Energy & Automation, Inc. All rights reser ved. Siemens Energy & Automation Industrial Products Divisi on Norwood Motor Plant 4620 Forest Avenue Norwood, OH 45212-3396 (513) 841-31 00 ...
Do you have a question concerning Siemens ANIM-03114?
Use the form below
If you did not solve your problem by using a manual Siemens ANIM-03114, ask a question using the form below. If a user had a similar problem with Siemens ANIM-03114 it is likely that he will want to share the way to solve it.