English dropdown-ico

Manual Hunter Fan 90058

40 pages 10.74 mb
Download

Go to site of 40

Summary
  • Hunter Fan 90058 - page 1

    41718-01 01/28/2008 1 Installation Guide 90052/90053/90054/90058 Saturn ™ Bath V entilator with Light READ and SA VE THESE INSTRUCTIONS ENGLISH See page 2 ESP AÑOL V ea la página 21 028_41718_EngS_1.28.08_Arial.indd 1 1/28/08 10:47:06 AM ...

  • Hunter Fan 90058 - page 2

    41718-01 01/28/2008 2 DISCONNECT ELECTRIC POWER SUPPL Y AND LOCK OUT SER VICE P ANEL BEFORE SER VICING UNIT W ARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y TO PERSONS, OBSERVE THE FOLLOWING: 1. For general ventilating use only . Do not use to exhaust hazard- ous or explosive materials and vapors. 2. T o avoid motor bearing damage an ...

  • Hunter Fan 90058 - page 3

    41718-01 01/28/2008 3 D E F G H I L M N x4 * * * NOTE: Strain relief cable connector must be installed. Not Included. A B C 95044-01-000 95029-01-000 75191-01-000 03242-07-133 95491-01-000 74508-03-133 95583-01/02/03/04-000 J 77521-01 K 65219 75184-01-133 94990-01/02/03-000 Extra Screws x2 I 3/8” Cable Connector x2 1 T urn off the power source. T ...

  • Hunter Fan 90058 - page 4

    41718-01 01/28/2008 4 5 4 7 G 8 F Remove the motor/blower from the housing. H E 3 Remove the pre-loaded screw tip covers. Remove the wiring cover screw . 6 Back out the pre-loaded screw tips until flush with the side of the housing. Remove the wiring cover . Remove packing material. 028_41718_EngS_1.28.08_Arial.indd 4 1/28/08 10:47:11 AM ...

  • Hunter Fan 90058 - page 5

    41718-01 01/28/2008 5 9 E Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and secure with the washer . Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. New Construction - attaching to joist 10 B C Choose Installation Option For New Constru ...

  • Hunter Fan 90058 - page 6

    41718-01 01/28/2008 6 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground A14 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light To gether *Option A1 3 Pull wires through the strain relief. Connect wires as shown. 0 A1 6 Connect 4” duct and vent to the outside. T ape joints. If d ...

  • Hunter Fan 90058 - page 7

    41718-01 01/28/2008 7 A1 9 I Secure the motor by tightening the 2 screws. A20 T urn on the power source. Connect wiring from the motor to the wiring cover plate. 0 0 0 0 A1 7 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. 0 0 0 0 H A1 8 ON OFF A21 T est ...

  • Hunter Fan 90058 - page 8

    41718-01 01/28/2008 8 B1 1 D E 5/8 1/2 5/8 1/2 B12 1/8” Bit B1 4 B15 B1 6 E B1 3 Slide the mounting rails into brackets. Mark position of screws by using holes as a template. Insert screws, leaving space between the screw head and the joist. Screws are not provided. New Construction – suspended between joists Position the correct depth mark at ...

  • Hunter Fan 90058 - page 9

    41718-01 01/28/2008 9 Tighten screws. Pull wires through the strain relief. Connect wires as shown. B17 B1 8 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground B19 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light To gether *Option B2 1 Connect 4” duct and vent to the outside. ...

  • Hunter Fan 90058 - page 10

    41718-01 01/28/2008 10 B2 7 E1 Go to step on page 17 to attach grille . B2 2 H Connect wiring from the motor to the wiring cover plate. H B2 3 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. B2 5 T urn on the power source. ON OFF B2 6 T est the motor . If ...

  • Hunter Fan 90058 - page 11

    41718-01 01/28/2008 11 C12 D E Existing Construction – accessible from above EXISTING FA N C1 1 NO EXISTING FA N 8” 8.5” OR Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.5”). Cut out an opening for the housing. Use the motor housing as a template to mark position. Sli ...

  • Hunter Fan 90058 - page 12

    41718-01 01/28/2008 12 C17 C18 C19 C20 C15 1/8” Bit C16 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. Tighten screws. Connect 4” duct and vent to the outside. T ape joints. If ducting does not fit securely , an adapter may ...

  • Hunter Fan 90058 - page 13

    41718-01 01/28/2008 13 C21 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground C22 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light To gether *Option Tighten the strain relief screws. Connect wires as shown. C24 H G F C2 3 Install the wiring cover plate. Make sure all wiring conn ...

  • Hunter Fan 90058 - page 14

    41718-01 01/28/2008 14 C25 H C26 I C2 7 ON OFF C2 8 Secure the motor by tightening the 2 screws. T urn on the power source. T est the motor . If the motor does not run, check the plug connection. C2 9 E1 Go to step on page 17 to attach grille . Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinch ...

  • Hunter Fan 90058 - page 15

    41718-01 01/28/2008 15 EXISTING FA N D1 1 E D12 Existing Construction – accessible only from below D13 2 1 D14 Pull wires through strain relief. Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.5”). Move the housing into position above the ceiling. Attach existing ducting to ...

  • Hunter Fan 90058 - page 16

    41718-01 01/28/2008 16 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground D16 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light To gether *Option H D18 H D19 D20 I Connect wires as shown. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires ...

  • Hunter Fan 90058 - page 17

    41718-01 01/28/2008 17 ON OFF D2 2 D2 3 E1 Go to step on page 17 to attach grille . D2 1 T est the motor . If the motor does not run, check the plug connection. T urn on the power source. Attaching the Grille Remove the thumbscrews. Connect wiring harness. M E E1 L E2 028_41718_EngS_1.28.08_Arial.indd 17 1/28/08 10:47:45 AM ...

  • Hunter Fan 90058 - page 18

    41718-01 01/28/2008 18 Insert the strain relief bracket’ s dog-leg tab so that it hooks over the lip of the motor . Reinstall the strain relief bracket screw . E5 Position the strain relief bracket under the motor as shown. E4 J Remove the strain relief bracket screw . E3 K Install 2 Max 60 watt A-15 bulbs (Not Included). E8 Attach thumbscrews. W ...

  • Hunter Fan 90058 - page 19

    41718-01 01/28/2008 19 Align glass dome and push up. E1 0 Screw glass dome into position. N E9 T rouble Shooting Problem: Fan does not come on. Solution:  • HunterFanBathV entilatorsareextremelyquiet.T oconrmthatthefanisrunning,placeyourhandneartheventstofeel the ...

  • Hunter Fan 90058 - page 20

    41718-01 01/28/2008 20 2500 Frisco A venue, Memphis, T ennessee 381 14 Printed in China © 2008 Hunter Fan Company W arranty Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: IfanypartofyourHunter ...

  • Hunter Fan 90058 - page 21

    41718-02 01/28/2008 21 Guía de instalación V entilador para baño Saturn ™ 90052/90053/90054/90058 con luz LEA y CONSERVE EST AS INSTRUCCIONES ESP AÑOL 028_41718_Span_1.28.08_Arial.indd 21 1/28/08 10:50:44 AM ...

  • Hunter Fan 90058 - page 22

    41718-02 01/28/2008 22 DESCONECTE LA ALIMENT ACIÓN ELÉCTRICA Y CIERRE EL P ANEL DE SER VICIO ANTES DE DAR MANTENIMIENT O A LA UNIDAD tc. Retire las cubiertas de las puntas de tornillo pre- cargadas. ADVERTENCIA P ARA REDUCIR EL RIESGO DE INCENDIO, CHOQUE ELÉCTRICO O LESIONES A PERSONAS, OBSERVE LO SIGUIENTE: 1. Sólo para uso de ventilación gen ...

  • Hunter Fan 90058 - page 23

    41718-02 01/28/2008 23 1 2 E I D E F G H I L M N x4 * * * NO TA : Debe estar instalado el manguito de alivio de tensión del cable. No incluido. A B C 95044-01-000 95029-01-000 75191-01-000 03242-07-133 95491-01-000 74508-03-133 95583-01/02/03/04-000 J 77521-01 K 65219 75184-01-133 94990-01/02/03-000 To rnillos adicionales x2 I Conector de cable de ...

  • Hunter Fan 90058 - page 24

    41718-02 01/28/2008 24 5 4 7 G 8 F H E 3 6 Retire las cubiertas de las puntas de tornillo precargadas. Retire el tornillo de la cubierta del cableado. Retire las puntas de tornillo precargadas hasta que estén a nivel con el lado del alojamiento. Retire la cubierta del cableado. Retire el material de embalaje. Retire el motor/soplador del alojamien ...

  • Hunter Fan 90058 - page 25

    41718-02 01/28/2008 25 9 E 10 B C A1 1 E 5/8 1/2 5/8 1/2 A1 2 Retire el primer tapón metálico de acceso del cableado. Utilice el segundo si es necesario. Inserte el manguito de alivio de tensión en el alojamiento y sujételo firmemente con la arandela. Ubique la correcta marca de profundidad en el borde inferior de la viga, según el espesor de ...

  • Hunter Fan 90058 - page 26

    41718-02 01/28/2008 26 A Motor del ventilador Luz Luz Ve rde Negro Interruptor 2 (CA) Blanco Negro Negro Blanco Blanco Cobre desnudo Ti erra A14 Negro Interruptor principal 1 (CA) *Opción Ve ntilador y luz principal juntos *Option 3 clavijas 2 clavijas A1 3 0 A1 6 Conecte un ducto de 4” y ventile hacia el exterior . Aplique cinta a las uniones. ...

  • Hunter Fan 90058 - page 27

    41718-02 01/28/2008 27 A1 9 I Asegure el motor apretando los 2 tornillos. A20 Encienda la fuente de alimentación. Conecte el cableado del motor a la placa de cubierta del cableado. 0 0 0 0 A1 7 V uelva a instalar el motor introduciendo las pestañas y levantando a su posición. Asegúrese que los alambres no se pellizquen entre el motor y el aloja ...

  • Hunter Fan 90058 - page 28

    41718-02 01/28/2008 28 B1 1 D E 5/8 1/2 5/8 1/2 B12 broca de 1/8 de pulg. B14 B15 B1 6 E B1 3 Deslice los rieles de montaje en los soportes. Marque la posición de los tornillos utilizando los agujeros como una plantilla. Introduzca los tornillos, dejando espacio entre la cabeza del tornillo y la viga. No se proporcionan los tornillos. Construcció ...

  • Hunter Fan 90058 - page 29

    41718-02 01/28/2008 29 B17 B1 8 A Motor del ventilador Luz Luz Ve rde Negro Interruptor 2 (CA) Blanco Negro Negro Blanco Blanco Cobre desnudo Ti erra B19 Negro Interruptor principal 1 (CA) *Opción Ve ntilador y luz principal juntos *Option 3 clavijas 2 clavijas B2 1 Conecte un ducto de 4” y ventile hacia el exterior . Aplique cinta a las uniones ...

  • Hunter Fan 90058 - page 30

    41718-02 01/28/2008 30 B2 7 E1 V aya al paso en la página 37 para f ijar la rejilla . B2 2 H Conecte el cableado del motor a la placa de cubierta del cableado. H B2 3 V uelva a instalar el motor introduciendo las pestañas y levantando a su posición. Asegúrese que los alambres no se pellizquen entre el motor y el alojamiento. B2 5 ENCENDIDO AP A ...

  • Hunter Fan 90058 - page 31

    41718-02 01/28/2008 31 C12 D E VENTILADOR EXISTENTE C1 1 SIN VENTILADOR EXISTENTE 8” 8.5” 5/8 1/2 5/8 1/2 C13 C14 Construcción existente – accesible desde arriba O Retire el ventilador existente y asegúrese que la abertura sea suficientemente grande para acomodar el alojamiento del motor nuevo (8” x 8.5”). Recorte una abertura para el a ...

  • Hunter Fan 90058 - page 32

    41718-02 01/28/2008 32 C17 C18 C19 C20 C15 broca de 1/8 de pulg. C16 T aladre un agujero en el centro de cada perfil. Introduzca los tornillos, dejando espacio entre la cabeza del tornillo y la viga. No se proporcionan los tornillos. Fije los rieles en los tornillos. Apriete los tornillos. Conecte un ducto de 4” y ventile hacia el exterior . Apli ...

  • Hunter Fan 90058 - page 33

    41718-02 01/28/2008 33 C21 A Motor del ventilador Luz Luz Ve rde Negro Interruptor 2 (CA) Blanco Negro Negro Blanco Blanco Cobre desnudo Ti erra C22 Negro Interruptor principal 1 (CA) *Opción Ve ntilador y luz principal juntos *Option 3 clavijas 2 clavijas C24 H G F C2 3 Apriete los tornillos. Conecte los alambres como se muestra. Instale la placa ...

  • Hunter Fan 90058 - page 34

    41718-02 01/28/2008 34 C25 H C26 I C2 7 ENCENDIDO AP AGAD O C28 C2 9 E1 V aya al paso en la página 37 para f ijar la rejilla . Asegure el motor apretando los 2 tornillos. Encienda la fuente de alimentación. Pruebe el motor . Si el motor no funciona, verifique la conexión del enchufe. V uelva a instalar el motor introduciendo las pestañas y leva ...

  • Hunter Fan 90058 - page 35

    41718-02 01/28/2008 35 VENTILADOR EXISTENTE D1 1 E D12 D13 2 1 D14 E D15 Construcción existente – accesible sólo desde abajo Tienda los cables a través del manguito de alivio de tensión. Retire el ventilador existente y asegúrese que la abertura sea suficientemente grande para acomodar el alojamiento del motor nuevo (8” x 8.5”). Mueva el ...

  • Hunter Fan 90058 - page 36

    41718-02 01/28/2008 36 A Motor del ventilador Luz Luz Ve rde Negro Interruptor 2 (CA) Blanco Negro Negro Blanco Blanco Cobre desnudo Ti erra D16 Negro Interruptor principal 1 (CA) *Opción Ve ntilador y luz principal juntos *Option 3 clavijas 2 clavijas H D18 H D19 D20 I F D17 G Conecte los alambres como se muestra. V uelva a instalar el motor intr ...

  • Hunter Fan 90058 - page 37

    41718-02 01/28/2008 37 ENCENDIDO AP AGAD O D22 D2 3 E1 V aya al paso en la página 37 para f ijar la rejilla . D2 1 M E E1 L E2 Pruebe el motor . Si el motor no funciona, verifique la conexión del enchufe. Encienda la fuente de alimentación. Fijación de la rejilla Retire los tornillos de mano. Conecte el mazo de cables. 028_41718_Span_1.28.08_Ar ...

  • Hunter Fan 90058 - page 38

    41718-02 01/28/2008 38 E5 E4 J E3 K Introduzca la pestaña en ángulo del soporte del aliviador de tensiones para que se enganche en el borde del motor . Reinstale el tornillo del soporte del aliviador de tensiones. Coloque el soporte del aliviador de tensiones debajo del motor como se muestra. Retire el tornillo del soporte del aliviador de tensio ...

  • Hunter Fan 90058 - page 39

    41718-02 01/28/2008 39 Solución de problemas Problema: El ventilador no está operando. Solución: • Los ventiladores de baño Hunter son muy silenciosos. Para conrmar que el ventilador esté funcionando, coloque su mano cerca de los conductos de ventilación para sentir el movimiento del aire. • Encienda la alimentación eléctrica, reempl ...

  • Hunter Fan 90058 - page 40

    41718-02 01/28/2008 40 Hunter Fan Company Extractor de aire para baño GARANTÍA LIMIT ADA Hunter Fan Company establece la siguiente garantía limitada al usuario o comprador original de este Extractor de aire para baño Hunter: Si alguna pieza de su Extractor de aire para baño Hunter (con excepción de las lámparas de vidrio y las bombillas) fal ...

Manufacturer Hunter Fan Category Ventilation Hood

Documents that we receive from a manufacturer of a Hunter Fan 90058 can be divided into several groups. They are, among others:
- Hunter Fan technical drawings
- 90058 manuals
- Hunter Fan product data sheets
- information booklets
- or energy labels Hunter Fan 90058
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hunter Fan 90058.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hunter Fan 90058, service manual, brief instructions and user manuals Hunter Fan 90058. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hunter Fan 90058.

Similar manuals

A complete manual for the device Hunter Fan 90058, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hunter Fan 90058 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hunter Fan 90058.

A complete Hunter Fan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hunter Fan 90058 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hunter Fan 90058, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hunter Fan 90058, that we can find in the current document
3. Tips how to use the basic functions of the device Hunter Fan 90058 - which should help us in our first steps of using Hunter Fan 90058
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hunter Fan 90058
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hunter Fan 90058 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hunter Fan 90058?

Use the form below

If you did not solve your problem by using a manual Hunter Fan 90058, ask a question using the form below. If a user had a similar problem with Hunter Fan 90058 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)