-
DeVillbiss Air Power Company Contractor Series - page 1
Nailer/Stapler Operation Manual MG-NS2X4A 7/16/99 This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. PLEASE READ THIS MANUAL. DeVilbiss Air Power Company • 213 Industrial Drive • Jackson, TN 38301-9615 Specifications MODEL NO. M ...
-
DeVillbiss Air Power Company Contractor Series - page 2
PAGE 2 Page Tool Specifications ................................................................ Front Cover Table of Contents ................................................................................... 2 Limited Warranty ..................................................................................... 3 Safety Guidelines & Warning ...
-
DeVillbiss Air Power Company Contractor Series - page 3
PAGE 3 All merchandise manufactured by DeVilbiss Air Power Company/ExCell Manufacturing is warranted to be free of defects in workmanship and material which occur during the first year from the date of purchase by the original purchaser (initial user). Products covered under this warranty include: air compressors, *air tools, accessories, service p ...
-
DeVillbiss Air Power Company Contractor Series - page 4
PAGE 4 HAZARD TO LOOK FOR Compressed Gas Excessive Operating Pressure Unsuitable Cleaning Solvents WHAT COULD HAPPEN Oxygen will react with oil in tool caus- ing an explosion. Flammable gases will ignite from sparking and cause the tool to explode, resulting in serious injury or death. THE TOOL COULD EXPLODE re- sulting in serious injury or death. ...
-
DeVillbiss Air Power Company Contractor Series - page 5
PAGE 5 Risk of head injury. WHAT COULD HAPPEN Metal fragments, fasteners, or other material could be projected against head or into eyes resulting in serious injury or property damage. Contin- ued exposure to an operating tool can result in permanent hearing dam- age. HOW TO PREVENT IT Always wear ANSI approved Z87 safety glasses, Z89.1 head protec ...
-
DeVillbiss Air Power Company Contractor Series - page 6
PAGE 6 Risk from flying objects. WHAT COULD HAPPEN Fasteners could ricochet or be propelled causing serious injury or property damage. When working along edges or next to voids in work surface, the con- tact trip safety mechanism could be depressed and allow the tool to dischar ge a fastener into the air or through thin work materials r e- sulting ...
-
DeVillbiss Air Power Company Contractor Series - page 7
PAGE 7 Do not store the tool in cold weather. Frost or ice can form on the operating valves or mechanisms and the tool may not operate correctly. In cold weather operation (near or below freezing), DO NOT USE a permanent antifreeze such as ethylene glycol for a cold weather lubricant. This type of anitfreeze will damage o-rings and seals of the too ...
-
DeVillbiss Air Power Company Contractor Series - page 8
PAGE 8 Always connect the Female Quick Cou- pler to the air hose. Never connect the Female Quick Coupler to the tool. Never carry the tool by the hose or pull the hose to move the tool or a com- pressor. Keep hoses away from heat, oil, and sharp edges. Replace any damaged, weak or worn hoses. Do not use any type of flammable gases or oxygen as a po ...
-
DeVillbiss Air Power Company Contractor Series - page 9
PAGE 9 NAILER FEMALE QUICK COUPLER MALE QUICK CONNECTOR OILER FILTER RECOMMENDED HOOK-UP The following illustration shows the proper hook-up which will help prolong the life of the Tool. AIR COMPRESSOR AIR HOSE (3/8" I.D.) FEMALE QUICK COUPLER MALE QUICK CONNECTOR (Supplied with Tool) Never keep the trigger pulled on contact trip tools when ca ...
-
DeVillbiss Air Power Company Contractor Series - page 10
PAGE 10 OPERATING A CONTACT TRIP TOOL: 1. Requires finger to be off the trigger and the nose of the Tool to be placed on the work surface. 2. The contact trip safety mechanism is then depressed against the work surface and the trigger pulled to drive a fastener. 3. The trigger is released after each fastener is driven. 4. Move the tool to the next ...
-
DeVillbiss Air Power Company Contractor Series - page 11
PAGE 11 Handle the tool carefully. Respect the tool as a working implement and always as- sume the tool contains fasteners: a. Never use the tool as a toy and engage in horseplay. b. Never aim or point the tool at any- one. The tool may contain fasteners. c. Always keep people and animals at a safe distance from the work area in case of accidental ...
-
DeVillbiss Air Power Company Contractor Series - page 12
PAGE 12 4. Push release button (if equipped) and slide feeder shoe forward. Protect your eyes and ears. Wear Z87 safety glasses with side shields. Wear hearing protection. Employers and users are responsible for ensuring the user or anyone near the tool uses the prescribed safety equipment. READ THIS MANUAL AND UNDERSTAND ALL SAFETY WARNINGS AND IN ...
-
DeVillbiss Air Power Company Contractor Series - page 13
PAGE 13 Disconnect tool from air compressor before adjusting, clearing jams, servicing, relocating and during non-operation. FASTENER JAMMED IN FASTENER DISCHARGE AREA: 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, NBSNC2X4 Release the magazine latch to open the magazine. CLEARING A JAM FROM THE TOOL Feeder Magazine Latch Nose ...
-
DeVillbiss Air Power Company Contractor Series - page 14
PAGE 14 FASTENER JAM INSIDE MAGAZINE : 1. Disconnect tool from air hose. 2. NF2502X4, NB1252X4, NB2002X4, NBSNC2X4 Release the magazine latch to open the magazine. Feeder Magazine Latch SNC1002x4 Pull feeder shoe back into "locked" position. 3. Remove jammed fasteners. 4. Reload fasteners into magazine. Refer to Loading the Tool section i ...
-
DeVillbiss Air Power Company Contractor Series - page 15
PAGE 15 PROBLEM Air leaking at trigger valve area. Air leaking through the exhaust deflector. Tool fails to drive fastener. Tool runs slow or has loss of power. SOLUTION Seals must be replaced & operation of Contact trip must be checked. On the NBSNC2x4 contact *AWSC for correct part. All other nailers purchase Trigger Repair Kit. Spring needs ...
-
DeVillbiss Air Power Company Contractor Series - page 16
PAGE 16 SOLUTION Replace feed pawl. Contact an *AWSC Replace feed pawl spring. Fasteners recommended for tool must be used. Replace with undamaged fasteners. Set platform to correct height. Adjust air pressur e to the correct PSI for that particular model nailer/stapler . Repair trigger action. Pur chase a T rigger Repair Kit Tighten screws. Instal ...
-
DeVillbiss Air Power Company Contractor Series - page 17
PAGE 17 NF2502X4 1/4" NPT INLET PLUG (AC100) FINISH NAIL FASTENERS 6 & 7MM COMBINATION CRESCENT WRENCH 3 4 5mm ALLEN WRENCHES FINISH NAILER LUBRICATING OIL SAFETY GLASSES 1 1 / 2 ” 1 ” 1 3 / 4 ” 2 1 / 4 ” 2” 2 1 / 2 ” 2 1 / 2 ” T ool Range 1 / 4 Tool 2X4 Part Number Description Qty per Box Steel Driver Series Comparable Part ...
-
DeVillbiss Air Power Company Contractor Series - page 18
PAGE 18 SNC1002X4 NARROW CROWN STAPLE FASTENER 1/4" NPT INLET PLUG (AC100) LUBRICATING OIL NARROW CROWN STAPLER 3 & 4 ALLEN WRENCHES SAFETY GLASSES Tool 2X4 Part Number Description Qty per Box Steel Driver Series Comparable Part SNCF06350 5/8" Staple 5000 2L16 SNCF07550 3/4" Staple 5000 2L19 SNCF10050 1" Staple 5000 2L25 SNC ...
-
DeVillbiss Air Power Company Contractor Series - page 19
PAGE 19 NB2002X4 LUBRICATING OIL 1/4" NPT INLET Plug (AC100) BRAD NAILER BRAD NAIL FASTENERS 4 3 ALLEN WRENCHES 5/8" SAFETY GLASSES Tool 2X4 Part Number Description Qty per Box Steel Driver Series Comparable Part NBF07550 3/4" Brad 5000 4F20 NBF10050 1" Brad 5000 4F25 NBF12550 1-1/4" Brad 5000 4F32 NBF15050 1-1/2" Brad ...
-
DeVillbiss Air Power Company Contractor Series - page 20
PAGE 20 NB1252X4 LUBRICATING OIL 1/4" NPT INLET PLUG (AC100) BRAD NAIL FASTENERS BRAD NAILER 4MM 3MM ALLEN WRENCHES SAFETY GLASSES Tool 2X4 Part Number Description Qty per Box Steel Driver Series Comparable Part NBF06350 5/8" Brad 5000 4F16 NBF07550 3/4" Brad 5000 4F20 NBF10050 1" Brad 5000 4F25 NBF12550 1-1/4" Brad 5000 4F ...
-
DeVillbiss Air Power Company Contractor Series - page 21
PAGE 21 NBSNC2X4 2X4 SIGNATURE SAFETY GLASSES LUBRICATING OIL 4MM 3MM ALLEN WRENCHES COMBINATION BRAD NAILER/ NARROW CROWN STAPLER NARROW CROWN STAPLE & BRAD NAIL FASTENERS 1/2" 3/4" 1" 1-1/2" 1/4" 1-1/4" 1-1/2" T ool Range 1 1 / 2 ” 1 1 / 4 ” 1 ” 3/4 ” 3/8 ” 5/8 ” 1 1 / ” 2 T ool Range Tool 2X4 ...
-
DeVillbiss Air Power Company Contractor Series - page 22
PAGE 22 REP AIR KITS A V AILABLE K-0521 T op Repair Kit K-0522 Bottom Repair Kit NF2502X4 K-1664 Driver Blade Kit K-0523 T rigger Repair Kit SNC1002X4 and NB1252X4 K-0525 T op Repair Kit K-0526 Bottom Repair Kit K-9025 Driver Blade Kit for SNC1002x4 K-1832 Drive Blade Kit for NB1252x4 K-0527 T rigger Repair Kit ...
-
DeVillbiss Air Power Company Contractor Series - page 23
PAGE 23 REP AIR KITS A V AILABLE K-0517 T op Repair Kit K-0518 Bottom Repair Kit NB2002X4 K-1850 Driver Blade Kit K-0519 T rigger Repair Kit NBSNC2X4 B340-06 T op Repair Kit B232-23 Bottom Repair Kit BN2B-10 Driver Blade Kit B251-02 T rigger Repair Kit ...
-
DeVillbiss Air Power Company Contractor Series - page 24
Nailer/Stapler Operation Manual Call our T oll Free Number 1-800-888-2468, Ext 2, then 1, to obtain the location of the nearest Authorized Service Center for ordering r epair parts and for warranty repairs. When ordering r epair parts from your local Authorized Service Center , always give the following information: • Model number of your product ...
Do you have a question concerning DeVillbiss Air Power Company Contractor Series?
Use the form below
If you did not solve your problem by using a manual DeVillbiss Air Power Company Contractor Series, ask a question using the form below. If a user had a similar problem with DeVillbiss Air Power Company Contractor Series it is likely that he will want to share the way to solve it.