English dropdown-ico

Manual PVI Industries FIREPOWER PV500-9

10 pages 0.19 mb
Download

Go to site of 10

Summary
  • PVI Industries FIREPOWER PV500-9 - page 1

    PV500 - 9 04 - 2000 ( 1 ) Section 9 PVI FIREPOWER  GAS BURNER TYPICAL CONSTRUCTION Figure 9 - 1 1. Burner housing 15. Air switch 29. Orifice location * 2. Air intake 16. Door assembly * 30. Electrode retaining bracket 3. Oil pump opening plug 17. Flame sensing electrode 31. Burner cover 4. Mounting flange 18. Ignition electrod e 32. Burner sight ...

  • PVI Industries FIREPOWER PV500-9 - page 2

    PV500 - 9 04 - 2000 ( 2 ) Section 9 POWER GAS BURNER START - UP (Refer to Figure 9 - 1 to identify burner parts) 1. Remove the enclosure panel cover on the water heater or boiler to expose the control circuit. Located on the back side of this cover is a wiring diagram of the unit. This diagram will show the controls used in our circuitry. 2. Visual ...

  • PVI Industries FIREPOWER PV500-9 - page 3

    PV500 - 9 04 - 2000 ( 3 ) Section 9 POWER GAS BURNER ST ART - UP (Con’t) clearance). Ensure plate is seated firmly against the gas spider and tighten the plate retaining screws. Recheck electrode setting as to gap and position. 15. Replace nozzle assembly; be sure to connect the flame and spark rod wires before in stalling nozzle assembly fully i ...

  • PVI Industries FIREPOWER PV500-9 - page 4

    PV500 - 9 04 - 2000 ( 4 ) Section 9 POWER GAS BURNER START - UP (Con’ t) 20. Direct Spark Ignition – (DSI) Burners – No pilot: 1. Connect a manometer to the manifold test port. Set the air shutter as shown on the tag attached to the gas train. This may not be the exact setting you end up with, but it is a good starting point. Tu rn the unit o ...

  • PVI Industries FIREPOWER PV500-9 - page 5

    PV500 - 9 04 - 2000 ( 5 ) Section 9 REMOVAL OF THE NOZZLE ASSEMBLY (EXCEPT “L” SERIES BURNERS) Figure 9 - 2 ELECTRODE POSITIONS “L,P,Q,R,S,T” SERIES BURNER Figure 9 - 3 ...

  • PVI Industries FIREPOWER PV500-9 - page 6

    PV500 - 9 04 - 2000 ( 6 ) Section 9 AIR ADJUSTMENT FIXED AIR BURNERS Loosen the locking screw and move the arm (B) along the scale (C) to the position wanted and tighten the screw. Check the air adjustment by making a flue gas analysis. Figure 9 - 4 AIR ADJUSTMENT VARIABLE AIR BURNERS Adjust first air shutter by loosening locking screw and move arm ...

  • PVI Industries FIREPOWER PV500-9 - page 7

    PV500 - 9 04 - 2000 ( 7 ) Section 9 Figure 9 - 6 NOTE: Nomograph is limited for use with Natural Gases with the following characteristics: Heating Value (gross) Btu/SCF - 970 - 1100; Specific G ravity - 0.57 - 0.70; Ultimate CO 2 - 11.7 - 12.2. ...

  • PVI Industries FIREPOWER PV500-9 - page 8

    PV500 - 9 04 - 2000 ( 8 ) Section 9 NOMOGRAPH FOR DETERMINING FLUE LOSSES FROM CO 2 AND FLUE TEMPERATURE FOR L.P. GAS (STEADY STATE EFFICIENCY CAN BE DETERMINED FROM THE FLUE LOSS) Figure 9 - 7 NOTE: Nomograph is limited for use with L.P. Gas with the following characteristics: Heating Value (gross) Btu/SCF – 2466 - 2542; Specific Gravity – 1.5 ...

  • PVI Industries FIREPOWER PV500-9 - page 9

    PV500 - 9 04 - 2000 ( 9 ) Section 9 TROUBLESHOOTING SUGGESTIONS GAS BURNER 1. BURNERS FAILS TO START A. Defective On/Off or fuel transfer switch. Replace swi tch. B. Control circuit has an open control contact. Check limits, low water cutoff, proof of closure switch and others as applicable. C. Bad fuse or switch open on incoming power source. Corr ...

  • PVI Industries FIREPOWER PV500-9 - page 10

    PV500 - 9 04 - 2000 ( 10 ) Section 9 TROUBLESHOOTING SUGGESTIONS GAS BURNER (Con't) 5. CARBON MONOXIDE READINGS ON GAS FIRING A. Flame impingement on "cold" heat transfer surfaces caused by excessive firing rate. Reduce firing rate to correct input volume. B. Incorre ct gas/air ratios. Readjust burner to correct CO 2 /O 2 levels, eli ...

Manufacturer PVI Industries Category Universal Remote

Documents that we receive from a manufacturer of a PVI Industries FIREPOWER PV500-9 can be divided into several groups. They are, among others:
- PVI Industries technical drawings
- FIREPOWER PV500-9 manuals
- PVI Industries product data sheets
- information booklets
- or energy labels PVI Industries FIREPOWER PV500-9
All of them are important, but the most important information from the point of view of use of the device are in the user manual PVI Industries FIREPOWER PV500-9.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals PVI Industries FIREPOWER PV500-9, service manual, brief instructions and user manuals PVI Industries FIREPOWER PV500-9. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product PVI Industries FIREPOWER PV500-9.

Similar manuals

A complete manual for the device PVI Industries FIREPOWER PV500-9, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use PVI Industries FIREPOWER PV500-9 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of PVI Industries FIREPOWER PV500-9.

A complete PVI Industries manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual PVI Industries FIREPOWER PV500-9 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the PVI Industries FIREPOWER PV500-9, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the PVI Industries FIREPOWER PV500-9, that we can find in the current document
3. Tips how to use the basic functions of the device PVI Industries FIREPOWER PV500-9 - which should help us in our first steps of using PVI Industries FIREPOWER PV500-9
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with PVI Industries FIREPOWER PV500-9
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of PVI Industries FIREPOWER PV500-9 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning PVI Industries FIREPOWER PV500-9?

Use the form below

If you did not solve your problem by using a manual PVI Industries FIREPOWER PV500-9, ask a question using the form below. If a user had a similar problem with PVI Industries FIREPOWER PV500-9 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)