English dropdown-ico

Manual Rinnai RHFE-263FAII

44 pages 1.74 mb
Download

Go to site of 44

Summary
  • Rinnai RHFE-263FAII - page 1

    ─ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. ─ WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical swi tch; do not use any phone in your building. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’ ...

  • Rinnai RHFE-263FAII - page 2

    2 Rinnai Corporation RHFE-263F A Ⅱ This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certifi ...

  • Rinnai RHFE-263FAII - page 3

    Safety Behavior and Practices Do not block the warm air discharge. Do not allow anyone to sleep directly in front of the appliance. Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. Children and adults should be alerted to the hazards of high surface temperature and should stay away to a ...

  • Rinnai RHFE-263FAII - page 4

    4 Rinnai Corporation RHFE-263F A Ⅱ Application For manufactured home (USA only) or mobile home or residential installation convertible for use with natural gas and liquefied petroleum gases (propane / LPG) when provision is made for the simple conversionfrom one gas to the other. General Description Forced combustion, forced convection, flued gas ...

  • Rinnai RHFE-263FAII - page 5

    5 Rinnai Corporation RHFE-263F A Ⅱ Features Clean Heating Forced Flue Type Easy Operation One-To uch Ignition Sensible Temperature Control Feature Comfortable Room Temperature Control and Display Warm Air Outlet at Floor Level (kee ps your feet warm) Function Lock Room Temperature Setting Memory Clean the Air Filter - Indi cator Lamp Energy Savin ...

  • Rinnai RHFE-263FAII - page 6

    6 Rinnai Corporation RHFE-263F A Ⅱ Getting to know your new RHFE-263FA Operating Instructions ...

  • Rinnai RHFE-263FAII - page 7

    7 Rinnai Corporation RHFE-263F A Ⅱ Control Panel All buttons beep when operated. RoomTemp Set Temp ON ON/OFF Filter Function Lock Economy Temp Control FUNCTION LOCK Lamp is "green" when this feature is on. FILTER LAMP Flashes red when filter is dirty. OPERATION LAMP This lamp turns "green" when power is on. Lamp will change to ...

  • Rinnai RHFE-263FAII - page 8

    8 Rinnai Corporation RHFE-263F A Ⅱ Operating Information Turning the heater ON When you press the ON/OFF button, the LED display will illuminate, the combustion fan will begin to run, and the spark will ignite the main burner. This heater has an automatic ignition system. When the main burner has lit, the combustion lamp will glow red, and the sp ...

  • Rinnai RHFE-263FAII - page 9

    9 Rinnai Corporation RHFE-263F A Ⅱ Operating Information Function Lock This feature locks the buttons to prevent unintended operation. Press the Function Lock button to activate and the lamp will glow. Pressing and holding the Function Lock button for two seconds will disengage the function lock. If the Function Lock is engaged while the unit is ...

  • Rinnai RHFE-263FAII - page 10

    10 Rinnai Corporation RHFE-263F A Ⅱ Care and Maintenance Filters Dirty filters reduce the air flow and the appliance ’ s ability to produce heat. The filters should be cleaned frequently during the heating season. If the filters become blocked the filter indicator lamp will flash red. Eventually the appliance will turn off and display fault cod ...

  • Rinnai RHFE-263FAII - page 11

    11 Rinnai Corporation RHFE-263F A Ⅱ Before Making a Service Call Before making a service call please check the following: ■ At Ignition: Heater does not operate. Warm air does not flow when the burner lights. Smoke or strange smells are produced on the first trial light up after installation. Sharp clicking noises at ignition, or when unit cuts ...

  • Rinnai RHFE-263FAII - page 12

    12 Rinnai Corporation RHFE-263F A Ⅱ T roubleshooting Problem Remedy Cause Not Plugged In Power Failure (Initial Installation) Air In Gas Pipe Gas Filter Blocked Miss Ignition Flue terminal obstructed Flue manifold not connected Louver obstructed Air filter blocked Gas Escape Function Lock Set Gas turned off at meter, tank, or valve. Plug In Push ...

  • Rinnai RHFE-263FAII - page 13

    Fault Codes If there is a malfunction the appliance may shut down as a safety precaution and display a fault code to assist in diagnosing the problem. The fault code will flash in the display on the control panel. When making a service call, this code will assist with diagnosing the fault. You may be able to clear the fault code by turning the heat ...

  • Rinnai RHFE-263FAII - page 14

    Installation Instructions A qualified service technician should install the appliance and inspect it before use. If you move, check the gas type in your new area. The local gas authority will be able to advise on local regulations. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANS ...

  • Rinnai RHFE-263FAII - page 15

    Gas Connection The gas supply line shall be gas tight, sized and so installed as to provide a supply of a gas sufficient to meet the maximum demand of the heater without loss of pressure. A shut off valve and appliance connector valve should be installed in the upstream of the gas line to permit servicing. Flexible pipe and any appliance connector ...

  • Rinnai RHFE-263FAII - page 16

    16 Rinnai Corporation RHFE-263F A Ⅱ The following items are included with the appliance. Owner ’ s Operation and Installation Manual Conversion Manual Conversion Kit A Vent Kit Manual valve set, backspacers, screws, pipe stoppers, and hardware listed below Installation Parts Flue Manifold ....................... 1 Spare rubber seal ............ ...

  • Rinnai RHFE-263FAII - page 17

    17 Rinnai Corporation RHFE-263F A Ⅱ Drilling Flue Hole Ensure that there are no gas or water lines, or electrical circuits in the wall location where the flue hole is to be drilled. Drill the flue hole using a 3 1/8 inch (80 mm) drill. The center of the hole must be located exactly at the specified point. See diagram. For weatherboard walls, dril ...

  • Rinnai RHFE-263FAII - page 18

    18 Rinnai Corporation RHFE-263F A Ⅱ Flue T erminal Clearances ...

  • Rinnai RHFE-263FAII - page 19

    19 Rinnai Corporation RHFE-263F A Ⅱ Ref Description Canadian Installations US Installations A Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm) B Clearance to wind ow or door that may be opened 12 inches (30 cm) 9 inches (23 cm) C Clearance to permanently clo sed window * * * D Vertical clearance to venti ...

  • Rinnai RHFE-263FAII - page 20

    20 Rinnai Corporation RHFE-263F A Ⅱ Flue Manifold Installation 1. Disassemble the flue manifold The flue consists of 3 parts: sleeve inside connection outside terminal Disassemble the flue manifold by first pu lling out the inside connectio n. To remove the outer terminal pull and release the two internal ties and then pull out the outer terminal ...

  • Rinnai RHFE-263FAII - page 21

    21 Rinnai Corporation RHFE-263F A Ⅱ Flue Manifold Installation 6. Lock the ties Pulling hard on the left and right hand ties, clip the ties over the notches inside the sleeve. You should be able to pull the ties 2 or 3 notches past the starti ng point. Cut the ties, leaving about 3/4 inch (20 mm) past the notch. Bend the ties back into the sleeve ...

  • Rinnai RHFE-263FAII - page 22

    22 Rinnai Corporation RHFE-263F A Ⅱ Extension Installation Kit If necessary, extention kits are available to extend the exhaust line and air intake hose between the manifold and the appliance. The maximum vent length is 13 feet (4m) with 2 bends. The bent pipe attached to the appliance dose not count toward the max limit of 2 bends. The maximum v ...

  • Rinnai RHFE-263FAII - page 23

    23 Rinnai Corporation RHFE-263F A Ⅱ Extension Kit Installation CAUTION Use the pipe stoppers, connectors, clamps, and screws according to these instructions in order to ensure no leakage of exhaust gases. Clearances exhaust pipe to combustibles 1 inch (25.4mm) exhaust pipe to non-combustibles zero Clamps Both the exhaust line and air intake hose ...

  • Rinnai RHFE-263FAII - page 24

    Extension Kit Installation Rinnai Corporation RHFE-263F A Ⅱ 24 ) EXHAUST PIPE (ADJUSTABLE) * EXHAUST PIPE(NON ADJUSTABLE) + AIR INTAKE HOSE , BENT ELBOW - LONG BENT ELBOW ⑥ HOSE JOINT ⑧ PIPE STOPPER B ⑨ PIPE CLAMP ⑩ WALL-FIXTURE ⑪ NUT ⑫ SCREW A ⑦ PIPE STOPPER A ⑬ SCREW B Item FOT-155 FOT-156 FOT-157 FOT-158 FOT-190 Description 1 1 ...

  • Rinnai RHFE-263FAII - page 25

    25 Rinnai Corporation RHFE-263F A Ⅱ Connecting the Appliance 1. Attach the air inlet hose to the flue manifold on either inlet position “ a ” or “ b ” . The unused inlet is plugged with the rubber cap supplied on the manifold. 2. Connect the flue elbow to the manifold while moving the appliance into position. 3. Fit the pipe stopper over ...

  • Rinnai RHFE-263FAII - page 26

    26 Rinnai Corporation RHFE-263F A Ⅱ Operating Instructions FOR YOUR SAFETY READ BEFORE OPERATING W ARNING If you do not follow these instructions exactly, a fire or explosion may result causing prope rty damage, personal injury or loss of life. A. This appliance does not have a pilot. It is equipped with an ignition device which automatically lig ...

  • Rinnai RHFE-263FAII - page 27

    27 Rinnai Corporation RHFE-263F A Ⅱ Cut-A way Diagram ...

  • Rinnai RHFE-263FAII - page 28

    28 Rinnai Corporation RHFE-263F A Ⅱ Wiring Diagram If any of the original wire as supplied with the appliance must be replaced, it must be replaced with type 18 AWG wire or its equivalent. MARK PS FR F TR SV1,2 ER SP FM OHS1,2 TF POV BL R.TH OH.TH PARTS NAME PRESSURE SENSOR FLAME ROD FUSE TRANSFORMER SOLENOID VALVE 1,2 ELECTRODE SPARKER CONVECTIO ...

  • Rinnai RHFE-263FAII - page 29

    29 Rinnai Corporation RHFE-263F A Ⅱ Ladder Diagram MODULATING SOLENOID VALVE TRANSFORMER ELECTRODE OVER HEAT THERMISTOR FUSE THERMAL FUSE THERMISTOR ...

  • Rinnai RHFE-263FAII - page 30

    30 Rinnai Corporation RHFE-263F A Ⅱ Flow Diagram ...

  • Rinnai RHFE-263FAII - page 31

    31 Rinnai Corporation RHFE-263F A Ⅱ Parts List For replacement parts call Rinnai at 1-800-621-9419. ...

  • Rinnai RHFE-263FAII - page 32

    32 Rinnai Corporation RHFE-263F A Ⅱ Parts List ...

  • Rinnai RHFE-263FAII - page 33

    33 Rinnai Corporation RHFE-263F A Ⅱ Parts List ...

  • Rinnai RHFE-263FAII - page 34

    34 Rinnai Corporation RHFE-263F A Ⅱ Parts List ...

  • Rinnai RHFE-263FAII - page 35

    35 Rinnai Corporation RHFE-263F A Ⅱ Parts List ...

  • Rinnai RHFE-263FAII - page 36

    36 Rinnai Corporation RHFE-263F A Ⅱ Parts List 001 308F-301 REAR PANEL ASS'Y 1 002 308F-316 TOP PLATE SUPPORTER 1 003 556F-313 FILTER BRACKET 2 004 308F-312 FILTER BRACKET 1 005 308F-324-2 HEAT SHIELD PANEL B 1 006 308F-454 BRACKET FIXER 2 007 308F-9077 WALL BRACKET 1 008 RHF300-152 SPACER BRACKET 1 009 308F-401-3 FRONT PANEL 1 010 308F-404- ...

  • Rinnai RHFE-263FAII - page 37

    37 Rinnai Corporation RHFE-263F A Ⅱ Parts List ITEM PART NUMBER PART NAME QTY 116 554F-114 ELECTRODE MOUNTING PLATE 1 117 556F-510 ELECTRODE 1 118 554F-147 ELECTRODE PACKING 1 119 308F-202-2 MANIFOLD 1 120 AU129-210 INJECTOR 2 121 556F-203-2 MANIFOLD PACKING 1 122 308F-318 WARM AIR SEAL PANEL 1 123 556F-224 BURNER BOX FITTING PLATE 1 124 554F-421 ...

  • Rinnai RHFE-263FAII - page 38

    38 Rinnai Corporation RHFE-263F A Ⅱ Parts List ...

  • Rinnai RHFE-263FAII - page 39

    39 Rinnai Corporation RHFE-263F A Ⅱ Parts List ITEM PART NUMBER PART NAME QTY 905 ZAA0422SZ SCREW 906 ZBA0408SZ SCREW 907 ZBA0416SZ SCREW 908 ZBB0410SC SCREW 909 ZBD0408SZ SCREW 910 ZDAA0410SZ SCREW 911 ZEAB0406SC SCREW 912 ZEAB0408SC SCREW 913 ZEAB0408SZ SCREW 914 ZEAB0408UK SCREW 915 ZEDB0408SB SCREW 916 ZEDB0408SZ SCREW 917 ZEDB0410SZ SCREW 91 ...

  • Rinnai RHFE-263FAII - page 40

    40 Rinnai Corporation RHFE-263F A Ⅱ Consumer Support W arranty Information Limited Warranty RHFE-263FA Ⅱ Gas Direct Vent Wall Furnace What is covered? This Warranty covers any defects in materials or workmanship, subject to the terms stated below. This Warranty extends to the original purchaser and subsequent transferees, but only while the pro ...

  • Rinnai RHFE-263FAII - page 41

    41 Rinnai Corporation RHFE-263F A Ⅱ Limited W arranty - continued What will Rinnai do? Rinnai will repair any part or component that is defective in materials or workmanship as set forth as follows. All repair parts must be genuine Rinnai parts. All repairs or replacements must be performed by an individual or servicing company that has been auth ...

  • Rinnai RHFE-263FAII - page 42

    Notes Rinnai Corporation RHFE-263F A Ⅱ 42 ...

  • Rinnai RHFE-263FAII - page 43

    ...

  • Rinnai RHFE-263FAII - page 44

    308F-2072 (00) Printed in Japan 2006.10 １ ０ ３ International Drive, Peachtree City, Georgia ３ ０ ２ ６ ９ Phone: １-８ ０ ０-６ ２ １-９ ４ １ ９ Fax: １ - ８ ８ ８-４ ７ ４-６ ６ ２ ４ ...

Manufacturer Rinnai Category Furnace

Documents that we receive from a manufacturer of a Rinnai RHFE-263FAII can be divided into several groups. They are, among others:
- Rinnai technical drawings
- RHFE-263FAII manuals
- Rinnai product data sheets
- information booklets
- or energy labels Rinnai RHFE-263FAII
All of them are important, but the most important information from the point of view of use of the device are in the user manual Rinnai RHFE-263FAII.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Rinnai RHFE-263FAII, service manual, brief instructions and user manuals Rinnai RHFE-263FAII. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Rinnai RHFE-263FAII.

Similar manuals

A complete manual for the device Rinnai RHFE-263FAII, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Rinnai RHFE-263FAII by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Rinnai RHFE-263FAII.

A complete Rinnai manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Rinnai RHFE-263FAII - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Rinnai RHFE-263FAII, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Rinnai RHFE-263FAII, that we can find in the current document
3. Tips how to use the basic functions of the device Rinnai RHFE-263FAII - which should help us in our first steps of using Rinnai RHFE-263FAII
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Rinnai RHFE-263FAII
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Rinnai RHFE-263FAII in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Rinnai RHFE-263FAII?

Use the form below

If you did not solve your problem by using a manual Rinnai RHFE-263FAII, ask a question using the form below. If a user had a similar problem with Rinnai RHFE-263FAII it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)