-
Fisher & Paykel DD60D 7 - page 1
NZ A U GB IE 590200C 12. 11 DD60D 7 models INST ALLA TION INSTRUCTIONS DishDr aw er TM dish w asher ...
-
Fisher & Paykel DD60D 7 - page 2
2 FOLL OW THE INS T ALLA TION SE QUENCE RELEV ANT T O Y OUR MODEL 1 PRODUCT & CABINETR Y DIMENSIONS DD60DC(H)X7 DD60DC(H)W7 DD60DC(H)B7 DD60DCM7 P ARTS SUPPLIED CA VITY PREP ARA TION MAXIMUM DIST ANCE OF HOSES & CORD FROM CHASSIS EDGE SECURE WITHOUT DRA WER REMOV AL RECOMMENDED METHOD (a) AL TERNA TIVE METHOD (b) SECURE B Y DRA WER REMOV AL ...
-
Fisher & Paykel DD60D 7 - page 3
3 SAFETY AND W ARNINGS - ALL MODELS ADDITIONAL SAFETY AND W ARNINGS - INTEGRA TED MODELS ONL Y 2a 2b W ARNING! Electrical shock hazard Before installing the dish washer , remov e the house fuse or open the circuit breaker . This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by ...
-
Fisher & Paykel DD60D 7 - page 4
4 P ARTS SUPPLIED - ALL MODELS 3a If the Drain hoses supplied are not long enough to reach y our services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses b y 3.6 m. The kit is available from the nearest F isher & Paykel Authorised Service Centre or our loc al website listed at the end of this document. Clam ...
-
Fisher & Paykel DD60D 7 - page 5
5 ADDITIONAL P ARTS SUPPLIED WITH INTE GRA TED MODELS 3b Panel bracket (2) (attached to product ) Panel mounting screws (12) T oekick mounting screws (5) T oekick mounting bracket (1) (A custom toekick panel of any material with thickness 9 - 19 mm can be screw ed to the plastic toekick mounting bracket) Integrated rectangular badge (2) (Satin chro ...
-
Fisher & Paykel DD60D 7 - page 6
6 H K M N A O O I Side Plan G F J L B C E D 4 PRODUCT DIMENSIONS Product dimensions (mm) Classic Designer Integrated Remote control Integrated Badge controls A overall height 1 of product 820-880 2 820-880 2 820-880 2 820-880 2 B overall width of product 599 599 599 599 C overall depth of product (excl. handle) 582 571 571 3 571 3 D depth of chassi ...
-
Fisher & Paykel DD60D 7 - page 7
7 5 CABINETR Y DIMENSIONS Plan Side P Q R S T Minimum clearances from adjac ent cabinetry min. 13 mm clearance from a corner cupboard min. 2 mm clearance to adjacent cupboard door Cabinetry dimensions (mm) Classic Designer Integrated Remote control Integrated Badge controls P inside height of cavity* min. 820 min. 820 min. 820 min. 820 Q inside wid ...
-
Fisher & Paykel DD60D 7 - page 8
8 The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry . The nal panel/cabinetry alignment is achieved by adjusting the feet: WID TH OF ALL P ANELS Measure A ( the width between adjacent door/drawer fr onts) and write it in the rst box below , then complete the equation. HEIGHT OF TH ...
-
Fisher & Paykel DD60D 7 - page 9
9 7 CA VITY PREP ARA TION W ater Connection Recommended COLD (Maximum 60°C ). ¾ “ BSP (GB20) to suit flat washer . Kosher requir ements Drains will need to be separated to satisfy kosher requirements . W e suggest you c onfirm acceptability with your local rabbi in respect to kosher installations. W ater Pressure W ater softener models Max. 1 M ...
-
Fisher & Paykel DD60D 7 - page 10
10 8 MAXIMUM DIST ANCE OF HOSES & CORD FR OM CHASSIS EDGE Drain hoses - 1800 mm Inlet hose - 1250 mm Power cord (excl. plug ) - 1650 mm Drain hoses - 2000 mm Inlet hose - 1650 mm Power cord (excl. plug ) - 1650 mm Lef t ha nd side Right han d side ...
-
Fisher & Paykel DD60D 7 - page 11
11 10a 9a A TT ACH SIDE MOUNTING BRA CKETS PULL THROUGH HOSE S & PUSH INT O THE CA VITY (x2) As you push product in, pull through hoses and co rd, ensuring they don ’t get kinked or twisted. optionally attach the two top mounting brackets Ensure the product is level A A A B B Clip all four side mounting brackets into their slots using a flat- ...
-
Fisher & Paykel DD60D 7 - page 12
12 13a FIT THE SUPPLIED T OEKICK P ANEL (OPTIONAL FOR INTEGRA TED MODELS) 3 4 6 8 5 7 9 1 2 19 19 Impor tant! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similiar Smooth the edge with a file. Be careful of s ...
-
Fisher & Paykel DD60D 7 - page 13
13 10b REMO VE THE L OWER DRA WER 100 mm 2 4 5 1 100 mm T o prevent kinked hoses, we rec ommend rotating the drawer anti-clockwise and resting it on its side after removal. Press the r elease tabs in on either side and push back to release drawer from runners . Push draw er runners back in. 9b PULL THROUGH HOSE S & PUSH INT O THE CA VITY option ...
-
Fisher & Paykel DD60D 7 - page 14
14 x4 13b REFIT THE DRA WER ONTO THE RUNNER S 2 1 4 5 3 Before r efitting the drawer , ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing for ward. Ensure the release tabs on both sides are reset fully . Ensure the drawer is now rotated clockwise back. 11b T o access the side brackets, you might hav e to p ...
-
Fisher & Paykel DD60D 7 - page 15
15 14b FIT THE SUPPLIED T OEKICK P ANEL (OPTIONAL FOR INTEGRA TED MODELS) 3 4 6 8 5 7 9 1 2 19 19 Impor tant! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similiar Smooth the edge with a file. Be careful of s ...
-
Fisher & Paykel DD60D 7 - page 16
16 3 1 1 2 INTE GRA TED MODELS WITH REMOTE (NZ A U) ONL Y - INST ALLING THE FR ONT P ANELS REMO VE BRA CKETS FROM PRODUCT A T T A CH P ANELS TO PR ODUCT EAR TH THE P ANELS A T T A CH P ANELS TO P ANEL BRA CKETS 15a 17a 18a 16a There must be at least 3 screws used each side Align bottom of panels with bottom of brackets When refitting the door pins, ...
-
Fisher & Paykel DD60D 7 - page 17
17 INTE GRA TED MODELS WITH REMOTE (NZ A U) ONL Y - INST ALLING THE FR ONT P ANELS ADJUS T P ANEL HEIGHT TO ALIGN THE CABINETR Y GAPS FITTING A CUST OM T OEKICK P ANEL 19a 20a Y ou can optionally glue your custom toekick panel onto the supplied panel With the front panels fitt ed, insert an appropriately sized Philips screw driver into the hole abo ...
-
Fisher & Paykel DD60D 7 - page 18
18 1 2 3 16 mm x6 INTE GRA TED MODELS WITH BADGE (GB IE) ONL Y - INST ALLING THE FRONT P ANELS & BADGE C ONTROLS DETERMINE BADGE CUT OUT L OCA TIONS ROUTE B ADGE WIRING THROUGH P ANEL A T T A CH P ANELS TO P ANEL BRA CKETS REMO VE BRA CKETS & DISCONNE CT BADGE S 15b 17b 18b 16b There must be at least 3 screws used each side Align bottom of ...
-
Fisher & Paykel DD60D 7 - page 19
19 INTE GRA TED MODELS WITH BADGE (GB IE) ONL Y - INST ALLING THE FRONT P ANELS & BADGE C ONTROLS 2 2 1 REA TT ACH B ADGE S & E AR TH THE P ANELS A T T A CH P ANELS TO PR ODUCT ADJUS T P ANEL HEIGHT TO ALIGN THE CABINETR Y GAPS FITTING A CUST OM T OEKICK P ANEL 19b 21b 22b 20b Push the panel in then up to locate. With the front panels fitt ...
-
Fisher & Paykel DD60D 7 - page 20
20 THERE ARE TWO DIFFERENT PL UMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUIT ABLE. 23 3 1 750-882.5 mm 2 * 1 2 38 mm max. 120 mm 750-882.5 mm * If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain hose support to required height Dishw asher using sink ...
-
Fisher & Paykel DD60D 7 - page 21
21 27 26 FINAL CHE CKLIS T TROUBLE SHOO TING Check all par ts are installed . Ensure that all panels and parts thereof are secure and final electrical tests hav e been conducted in accordanc e with local electrical regulations. Ensure product is level , securely fastened t o the cabinetry and opens and closes freely . The draw ers must be free t o ...
Do you have a question concerning Fisher & Paykel DD60D 7?
Use the form below
If you did not solve your problem by using a manual Fisher & Paykel DD60D 7, ask a question using the form below. If a user had a similar problem with Fisher & Paykel DD60D 7 it is likely that he will want to share the way to solve it.