English dropdown-ico

Manual Stow CD6CE13H18

34 pages 1.07 mb
Download

Go to site of 34

Summary
  • Stow CD6CE13H18 - page 1

    OPERA TION MANUAL P/N 35440 THIS MANU AL MUST A CCOMP ANY THE EQ UIPMENT A T ALL TIMES. T o find the latest revision of this publication, visit our website at: www .stowmfg.com Re vision #2 (12/20/07) CUTTER 1 CE SERIES MODEL CD6CE13H18 CONCRETE/ASPHAL T SA W (HONDA GX390 GASOLINE ENGINE) ...

  • Stow CD6CE13H18 - page 2

    P A GE 2 — STO W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) Engine exhaust and some of its constituents, and some dust created of California to cause cancer , birth defects and other repr oductive harm. by power sanding, sawing, grinding, drilling and other construction activities contains chemicals kno wn to the State Some exampl ...

  • Stow CD6CE13H18 - page 3

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 3 Grinding/cutting/drilling of masonry , concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay , granite and numerous other minerals and rocks. Repeate ...

  • Stow CD6CE13H18 - page 4

    P A GE 4 — STO W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — T ABLE OF CONTENTS Proposition 65 W ar ning ............................................. 2 Silicosis/Respirator y W a r nings .................................. 3 T able Of Contents ..................................................... 4 Saf e ...

  • Stow CD6CE13H18 - page 5

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 5 ST O W CUTTER 1 CE SA W — SAFETY MESSA GE ALER T SYMBOLS Safety precautions should be followed at all times when operating this equipment. F ailure to read, understand and comply with the Safety Messages and Operating Instructions could result in injury to yourself or others. ...

  • Stow CD6CE13H18 - page 6

    P A GE 6 — STO W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) Accidental Starting AL W A YS place the engine ON/OFF switch in the OFF position, when the saw is not in use. Over Speed Conditions NEVER tamper with the factory settings of the engine gove r nor . P ersonal injur y and damage to the engine or equipment can result if oper ...

  • Stow CD6CE13H18 - page 7

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 7 The following safety guidelines should always be used when operating the CUTTER 1 CE Saw . SAFETY ■ DO NOT operate or service this equipment before you read, understand, and comply with all safety messages in this manual. The manual must be kept available and accessible to th ...

  • Stow CD6CE13H18 - page 8

    P A GE 8 — STO W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — RULES FOR SAFE OPERA TION ■ Examine blade flanges f or damage and e xcessive w ear . ■ Ensure the cleanliness of the blade before blade is installed. Blade should fit snugly on the shaft and against the inside/ outside blade flanges. ■ En ...

  • Stow CD6CE13H18 - page 9

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 9 Figure 1. CUTTER 1 CE Decals ST O W CUTTER 1 CE SA W — RULES FOR SAFE OPERA TION EMERGENCIES ■ AL W A YS know the location of the nearest fire extinguisher . ■ AL W A YS know the location of the nearest first aid kit . ■ In emergencies always know the location of the ne ...

  • Stow CD6CE13H18 - page 10

    P A GE 10 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — SPECIFICA TIONS (SA W) Figure 2. CUTTER 1 CE Dimensions Side View Front Vie w A C B F G D E * Vibration (at handle) results with Cutter 1 CE Saw cutting concrete at a depth of 1-1/2 inches (38.1 mm) with an 18" (45.7 cm) blade , FULL THR ...

  • Stow CD6CE13H18 - page 11

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 11 ST O W CUTTER 1 CE SA W — SPECIFICA TIONS (ENGINE) ) e n i g n E ( s n o i t a c i f i c e p S . 2 e l b a T e n i g n E l e d o M A D N O H 2 T W Q 1 U 0 9 3 X G / 2 T W Q 1 K 0 9 3 X G e p y T e l g n i S , e k o r t s 4 d e l o o c - r i A e n i g n E e n i l o s a G , V ...

  • Stow CD6CE13H18 - page 12

    P A GE 12 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — GENERAL INFORMA TION The STOW CUTTER 1 CE saws are designed for wet cutting of concrete or asphalt utilizing Diamond Blades. These saws ha v e been engineered for general and industrial flat sawing applications. The reinforced steel box frame ...

  • Stow CD6CE13H18 - page 13

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 13 ST O W CUTTER 1 CE SA W — CONTROLS & COMPONENTS Figures 3 shows the location of the basic controls or components for the CUTTER 1 CE. Listed below is a brief explanation of each control or component. 1 . Hand Grips/Handlebar – When operating the saw , place both hands ...

  • Stow CD6CE13H18 - page 14

    P A GE 14 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) Figure 4. Engine Controls and Components Initial Servicing The engine (Figure 4) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer's engine manual for instructions & details of operation and servicing. 1 . ...

  • Stow CD6CE13H18 - page 15

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 15 ST O W CUTTER 1 CE SA W — PREP ARA TION/PRE-INSPECTION PREP ARA TION / PRE-INSPECTION 1 . Read and fully understand this manual, the saf ety intructions in par ticular , and the engine manufacturer's manual supplied with the saw . 2 . Select the correct blade for each a ...

  • Stow CD6CE13H18 - page 16

    P A GE 16 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) Figure 9. Pulley Alignment 3 . Check V -belt tension by using a tension meter (3.0 lbs ./ 1.36Kg) against the inside belt at a mid point between the two pulleys, or by deflecting the center belt at a mid point 3/16" (5 mm). 4. DO NO T over or under tighten the V -b ...

  • Stow CD6CE13H18 - page 17

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 17 F ailure to thoroughly inspect the diamond blade (Figure 10) for operational safety could result in damage to the blade or the saw , and may cause injury to the user or others in the operating area. Discard damaged or worn blades and replace with fresh blade. Figure 10. Diamon ...

  • Stow CD6CE13H18 - page 18

    P A GE 18 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) W ARNING F ailure to thoroughly inspect the diamond blade for operational safety could result in damage to the blades or the saw and may cause injury to the user or others in the operating area. 2. Blade Guard - Pivot the blade guard front cover all the way back. The gu ...

  • Stow CD6CE13H18 - page 19

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 19 ST O W CUTTER 1 CE SA W— BLADE PLA CEMENT 6. Inner Flange (Collar) - This flange is fix ed upon the spindle. The inside surface of the flange must be free of debris and permit a tight closure on the surface of the blade. W ARNING Dropping or forcing the blade onto the cuttin ...

  • Stow CD6CE13H18 - page 20

    P A GE 20 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W— RAISE/LO WER AND DEPTH ST OP Raise/Lower and Depth Stop The saw is equipped with a Raise/Lower and Depth Stop Assembly that is supported by the following components. (Figure 13) Figure 13. Cutting Depth - Raise/Lower System 1 . Adjusting Hand ...

  • Stow CD6CE13H18 - page 21

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 21 ST O W CUTTER 1 CE SA W — INITIAL ST ART -UP DO NOT attempt to operate the saw until this manual has been read and thoroughly understood. Engine operating steps ma y v ar y . See included engine manufacturer's operating manual. Figure 16. Engine Fuel V alve Lever 2 . En ...

  • Stow CD6CE13H18 - page 22

    P A GE 22 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) 7 . Grasp the star ter grip (Figure 21) and slowly pull it out. The resistance becomes the hardest at the compression point. Pull the starter grip briskly and smoothly for starting. Figure 21. Starter Grip 9 . Before the saw is placed into operation, run the engine for ...

  • Stow CD6CE13H18 - page 23

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 23 ST O W CUTTER 1 CE SA W — OPERA TION AL W A YS keep clear of r otating or mo ving par ts while operating this equipment. W ARNING 4 . When blade has reached full cutting depth, slowly walk behind the saw at a rate that will allow the engine to operate without losing optimum ...

  • Stow CD6CE13H18 - page 24

    P A GE 24 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — OPERA TION Restarting After Intervention If cutting is interrupted where the engine stops or is turned off while the blade is still in the cut: a. T ur n Engine Off switches to "OFF" b. Raise the blade out of the cut c. Restart the ...

  • Stow CD6CE13H18 - page 25

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 25 Drive Belt Refer to page 18 of this manual for Drive Belt adjustment procedures and Removal and Replacement procedures. See the engine manual supplied with your machine for appropriate engine maintenance schedule and troubleshooting guide for problems. ST O W CUTTER 1 CE SA W ...

  • Stow CD6CE13H18 - page 26

    P A GE 26 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — MAINTENANCE Figure 23. Engine Oil Change Dispose of used oil properly . DO NOT pour used oil on the ground, down a drain, or throw in the trash. Used oil can generally be taken to your local recycling center or service station for reclamation ...

  • Stow CD6CE13H18 - page 27

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 27 ST O W CUTTER 1 CE SA W — OPTIONAL W A TER T ANK 1 6 8 7 9 11 12 10 13 W A TER T ANK KIT (OPTION) 1 . Locate all parts listed in the parts list. 2 . Slide the T ank Shelf (item 1, Figure 24) ov er the top of the engine so the recoil starter fits through the large opening in ...

  • Stow CD6CE13H18 - page 28

    P A GE 28 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — OPTIONAL W A TER T ANK 9 Place the W ater T ank (with the hose assembled), onto the T ank Shelf so the v alv e and hose are resting in the notch of the top of the T ank Shelf . (Figure 26) 10. Place the Bungee Cord (item 4) o v er the Water T ...

  • Stow CD6CE13H18 - page 29

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 29 ST O W CUTTER 1 CE SA W — TROUBLESHOO TING (SA W) G N I T O O H S E L B U O R T E D A L B . 5 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S . g n i t t u c s p o t s r o s w o l s e d a l B g n i e b l a i r e t a m e h t r o f d r a h o o t e d a l B ...

  • Stow CD6CE13H18 - page 30

    P A GE 30 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) ST O W CUTTER 1 CE SA W — TROUBLESHOO TING (ENGINE) ) E N I G N E ( G N I T O O H S E L B U O R T . 6 E L B A T M O T P M Y SE S U A C E L B I S S O PN O I T U L O S o n t u b , e l b a l i a v a s i l e u f " , t r a t s o t t l u c i f f i D . " g u l p k ...

  • Stow CD6CE13H18 - page 31

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 31 ST O W CUTTER 1 CE SA W — TROUBLESHOO TING (ENGINE) ) D E U N I T N O C , E N I G N E ( G N I T O O H S E L B U O R T . 6 E L B A T M O T P M Y SE S U A C E L B I S S O PN O I T U L O S r e p o r p s i n o i s s e r p m o c " r e w o p n i k a e W " . e r i f s i m ...

  • Stow CD6CE13H18 - page 32

    P A GE 32 — ST O W CUTTER 1 CE — OPERA TION MANU AL — REV . #2 (12/20/07) TERMS AND CONDITIONS OF SALE — P ART S T erms and Conditions of Sale STOW Construction Equipment ST O W CONSTRUCTION EQUIPMENT POST OFFICE BO X 6254 CARSON, CALIFORNIA 90749 310-661-4242 • 877-BUY -ST O W F AX: 310-604-9237 E-MAIL: stow@stowmfg.com www .stowmfg.com ...

  • Stow CD6CE13H18 - page 33

    STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 33 NO TE P A GE ...

  • Stow CD6CE13H18 - page 34

    OPERA TION MANUAL Y our Local Dealer is: © COPYRIGHT 2007, MUL TIQUIP INC. Multiquip Inc, and the STOW logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission. This manual MUST accompany the equ ...

Manufacturer Stow Category Saw

Documents that we receive from a manufacturer of a Stow CD6CE13H18 can be divided into several groups. They are, among others:
- Stow technical drawings
- CD6CE13H18 manuals
- Stow product data sheets
- information booklets
- or energy labels Stow CD6CE13H18
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stow CD6CE13H18.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stow CD6CE13H18, service manual, brief instructions and user manuals Stow CD6CE13H18. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stow CD6CE13H18.

Similar manuals

A complete manual for the device Stow CD6CE13H18, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stow CD6CE13H18 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stow CD6CE13H18.

A complete Stow manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stow CD6CE13H18 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stow CD6CE13H18, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stow CD6CE13H18, that we can find in the current document
3. Tips how to use the basic functions of the device Stow CD6CE13H18 - which should help us in our first steps of using Stow CD6CE13H18
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stow CD6CE13H18
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stow CD6CE13H18 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stow CD6CE13H18?

Use the form below

If you did not solve your problem by using a manual Stow CD6CE13H18, ask a question using the form below. If a user had a similar problem with Stow CD6CE13H18 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)