English dropdown-ico

Manual Classen SC-16

24 pages 1.14 mb
Download

Go to site of 24

Summary
  • Classen SC-16 - page 1

    SOD CUTTER OPERA TOR’S/P AR TS MANU AL SC-12 SC-16 SC-18 SC-20 SC-24 Schiller -Pfeiffer , Inc. 1028 Str eet Road • Southampton, P A 18966 T elephone: 1-800-366-6268 ...

  • Classen SC-16 - page 2

    T ABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Thank Y ou . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Read This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W arranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Classen SC-16 - page 3

    1 PRE-DELIVER Y CHECK LIST Check the following before you deliver the sod cutter to the customer . 1. Guards and shields fastened in place. 2. Decals fastened and legible. 3. T ire pressure. 4. Gas lever on engine turned on. 5. All eight lubrication points greased. 6. 2:1 gearbox oil level. 7. Engine oil level. 8. Air cleaner . 9. T ouch up scratch ...

  • Classen SC-16 - page 4

    2 SAFETY HANDLE FUEL SAFEL Y - A V OID FIRES Handle gasoline with care; it is highly flammable. Use an approved gasoline container . Fill the fuel tank outdoors. DO NOT fill tank completely full. DO NOT smoke while you fill fuel tank. DO NOT remove gas cap if engine is running. READ SAFETY SIGNS Carefully read and follow all caution stickers. W ARN ...

  • Classen SC-16 - page 5

    3 OPERA TING THE SOD CUTTER PREP ARA TION 1. Police lawn area for obstacles and debris (i.e. sprinklers, hoses, toys, etc.). Remove all items. 2. Make sure underground sprinkler heads and other hidden obstacles are marked to prevent damage. 3. Mark other areas where sod cutting will be a problem or too risky (i.e. mud, tree roots, steep hills). OPE ...

  • Classen SC-16 - page 6

    4 TROUBLESHOOTING CHAR T PROBLEM CAUSE REMEDY Blade will not stay in ground a. Bottom of blade is r ounded off a. Blade should be sharpened or replaced Belts jump off a. W rong type of belt b. Pulley misalignment a. Use only the special factory belt b. Realign pulley NOTES: ___________________________________________________________________________ ...

  • Classen SC-16 - page 7

    5 SOD CUTTER P AR TS MANU AL SC-12/5.5 – S.N. 000372 & UP SC-12/8.0 – S.N. 000136 & UP SC-16/5.5 – S.N. 000104 & UP SC-18/5.5 – S.N. 003956 & UP SC-18/8.0 – S.N. 000413 & UP SC-20/5.5 – S.N. 000141 & UP SC-20/8.0 – S.N. 000164 & UP SC-24/8.0 – S.N. 000147 & UP ...

  • Classen SC-16 - page 8

    6 SOD CUTTER MAIN FRAME 1 C400235 1 SOD CUTTER FRAME 2 C500131 2 1/2" LOCK NUT 3 C500150 2 1/2" x 1-1/2" BOL T 4 C400232 1 SMALL GUARD 5 C400114 1 DUAL DRIVE CLUTCH ARM 6 C500101 4 5/16" NUT 7 C500115 9 5/16" LOCK WASHER 8 C500140 6 5/16" x 3/4" BOL T 9 C500146 2 3/8" x 1-1/2" BOL T 10 C500083 6 5/16&quo ...

  • Classen SC-16 - page 9

    7 1 C100005 1 HONDA 5.5 hp ENGINE w/DEFLECTOR 1 C100114 1 HONDA 8.0hp ENGINE w/DEFLECTOR 2 C100028 1 PULLEY w/ HUB & BOL TS, 4" x 22mm 3 C100024 1 B56 V-BEL T , 5.5hp MODEL 3 C100113 1 B59 V-BEL T , 8.0hp MODEL 4 C500011 1 3/16" x 1 3/4" SQUARE KEY 5 C500029 2 1/4" x 3/4" BOL T 6 C100023 1 HUB, T APERLOCK 7 C100022 1 PU ...

  • Classen SC-16 - page 10

    8 SOD CUTTER HANDLE ASSEMBL Y 1 2 3 4 5 29 7 8 9 10 11 12 13 6 6 15 16 17 18 19 20 21 22 23 6 24 23 23 24 27 26 25 6 4 28 29 30 49 28 4 28 29 20 6 40 2 QTY/PER KEY P ART NO . SHEET DESCRIPTION 1 C100018 1 L.H. HANDLE GRIP 2 C400006 1 MAIN HANDLE 3 C300068 1 HANDLE BRACE 4 C500043 6 3/8" x 1" BOL T 5 C100019 1 TWIST GRIP THROTTLE 6 C500041 ...

  • Classen SC-16 - page 11

    9 4 43 D 34 31 32 33 SEE DI AG RAM A 33 35 10 38 10 32 40 22 23 24 42 SEE DI AG RAM B 41 33 32 40 39 40 37 14 9 50 36 SEE MAI N FRAME PAGE FOR BLADE ADAPTO R PA R T NU MB ER S 3 4 5 43 44 45 46 47 26 DI A GRAM B NOTE: Whe n installing se als, make sure spring side of seal is away from be aring. 48 43 44 45 47 26 44 43 DI A GRAM A RAM A MBERS ...

  • Classen SC-16 - page 12

    10 ONE YEAR LIMITED W ARRANTY Effective January 1, 1994 For the period of one year from the date of purchase, CLASSEN MFG., INC. will repair or replace for the original purchaser (90 days if used for rental purposes) free of charge, any part or parts found upon the examination of our factory authorized servic e station, or by the factory in Norfolk ...

  • Classen SC-16 - page 13

    COR T ADOR DE TEPE MANU AL DEL OPERADOR/PIEZAS SC-12 SC-16 SC-18 SC-20 SC-24 Schiller -Pfeiffer , Inc. 1028 Str eet Road • Southampton, P A 18966 T eléfono: + (877) 596 6337 ...

  • Classen SC-16 - page 14

    ÍNDICE INTRODUCCIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Gracias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Lea este manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ...

  • Classen SC-16 - page 15

    1 LIST A DE COMPROBACIÓN ANTERIOR A LA ENTREGA Compruebe lo siguiente antes de entregar el cortador de tepe al cliente. 1. Protectores y pantallas sujetos en posición. 2. Calcomanías sujetas y legibles. 3. Presión de los neumáticos 4. Palanca de gasolina del motor en la posición encendida. 5. Los ocho puntos de lubricación engrasados. 6. Niv ...

  • Classen SC-16 - page 16

    2 SEGURIDAD MANIPULE EL COMBUSTIBLE CON CUIDADO – EVITE LOS INCENDIOS Manipule la gasolina con cuidado, ya que es muy inflamable. Use un recipiente de gasolina aprobado. Llene el depósito de combustible al aire libre. NO llene el depósito completamente. NO fume mientras llene el depósito de combustible. NO quite la tapa de la gasolina con el m ...

  • Classen SC-16 - page 17

    3 OPERACIÓN DEL COR T ADOR DE TEPE PREP ARACIÓN 1. Observe el área del césped para ver si hay obstáculos y objetos sueltos (por ejemplo, aspersores, mangueras, juguetes, etc). Quite todos los componentes. 2. Asegúrese de que las cabezas de los aspersores subterráneos y otros obstáculos ocultos estén marcados para impedir daños. 3. Marque ...

  • Classen SC-16 - page 18

    4 PROBLEMA CAUSA SOLUCIÓN La hoja no permanece en el terreno a. La parte inferior de la hoja está redondeada a. La hoja debe afilarse o reemplazarse Las correas saltan y se salen a. Tipo de corr ea equivocado b. Polea desalineada a. Use solamente la correa de fábrica especial b. V uelva a alinear la polea NOT AS:_________________________________ ...

  • Classen SC-16 - page 19

    5 COR T ADOR DE TEPE MANU AL DE PIEZAS SC-12/5.5 – N/S 000372 y sig. SC-12/8.0 – N/S 000136 y sig. SC-16/5.5 – N/S 000104 y sig. SC-18/5.5 – N/S 003956 y sig. SC-18/8.0 – N/S 000413 y sig. SC-20/5.5 – N/S 000141 y sig. SC-20/8.0 – N/S 000164 y sig. SC-24/8.0 – N/S 000147 y sig. ...

  • Classen SC-16 - page 20

    6 BASTIDOR PRINCIP AL EL COR T ADOR DE TEPE 1 C400235 1 BASTIDOR DEL CORT ADOR DE TEPE 2 C500131 2 TUERCA DE TRABA DE 1/2” 3 C500150 2 PERNO DE 1/2” x 1 1/2” 4 C400232 1 PROTECTOR PEQUEÑO 5 C400114 1 BRAZO DEL EMBRAGUE DE IMPULSIÓN DOBLE 6 C500101 4 TUERCA DE 5/16” 7 C500115 9 ARANDELA DE TRABA DE 5/16” 8 C500140 6 PERNO DE 5/16” x 3/ ...

  • Classen SC-16 - page 21

    7 1 C100005 1 MOTOR HONDA DE 5,5 HP CON DEFLECTOR 1 C100114 1 MOTOR HONDA DE 8,0 HP CON DEFLECTOR 2 C100028 1 POLEA CON CUBO Y PERNOS DE 4” x 22 mm 3 C100024 1 CORREA TRAPECIAL B56 MODELO DE 5,5 HP 3 C100113 1 CORREA TRAPECIAL B59 MODELO DE 8,0 HP 4 C500011 1 CHAVET A CUADRADA DE 3/16” x 1 3/4” 5 C500029 2 PERNO DE 1/4” x 3/4” 6 C100023 1 ...

  • Classen SC-16 - page 22

    8 CONJUNTO DE EMPUÑADURA DEL COR T ADOR DE TEPE 1 2 3 4 5 29 7 8 9 10 11 12 13 6 6 15 16 17 18 19 20 21 22 23 6 24 23 23 24 27 26 25 6 4 28 29 30 49 28 4 28 29 20 6 40 2 CAD A./POR CLAVE N° DE PIEZA. HOJA DESCRIPCIÓN 1 C100018 1 ASIDERO DEL MANILLAR IZQUIERDO 2 C400006 1 MANILLAR PRINCIP AL 3 C300068 1 TIRANTE DEL MANILLAR 4 C500043 6 PERNO DE 3 ...

  • Classen SC-16 - page 23

    9 4 43 D 34 31 32 33 SEE DI AG RAM A 33 35 10 38 10 32 40 22 23 24 42 SEE DI AG RAM B 41 33 32 40 39 40 37 14 9 50 36 SEE MAI N FRAME PAGE FOR BLADE ADAPTO R PA R T NU MB ER S 3 4 5 43 44 45 46 47 26 DI A GRAM B NOTE: Whe n installing se als, make sure spring side of seal is away from be aring. 48 43 44 45 47 26 44 43 DI A GRAM A RAM A MBERS VEA EL ...

  • Classen SC-16 - page 24

    10 UN AÑO DE GARANTÍA LIMIT ADA En vigor el 1 de enero de 1994 Durante el período de un año contado a partir de la fecha de compra, CLASSEB MFG., INC. reparará o reemplazará al comprador original (90 días si se alquila) de forma gratuita, cualquier pieza o piezas que después de examinarlas en nuestra estación de servicio autorizada de nues ...

Manufacturer Classen Category Brush Cutter

Documents that we receive from a manufacturer of a Classen SC-16 can be divided into several groups. They are, among others:
- Classen technical drawings
- SC-16 manuals
- Classen product data sheets
- information booklets
- or energy labels Classen SC-16
All of them are important, but the most important information from the point of view of use of the device are in the user manual Classen SC-16.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Classen SC-16, service manual, brief instructions and user manuals Classen SC-16. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Classen SC-16.

Similar manuals

A complete manual for the device Classen SC-16, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Classen SC-16 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Classen SC-16.

A complete Classen manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Classen SC-16 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Classen SC-16, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Classen SC-16, that we can find in the current document
3. Tips how to use the basic functions of the device Classen SC-16 - which should help us in our first steps of using Classen SC-16
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Classen SC-16
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Classen SC-16 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Classen SC-16?

Use the form below

If you did not solve your problem by using a manual Classen SC-16, ask a question using the form below. If a user had a similar problem with Classen SC-16 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)