English dropdown-ico

Manual Siemens PC 670

200 pages 4.78 mb
Download

Go to site of 200

Summary
  • Siemens PC 670 - page 1

    Preface, Contents Product Overview 1 Starting Up the Computing Unit 2 Connecting and Switching on the Computing Unit 3 Maintaining and Extending the Computing Unit 4 Configuring the Computing Unit in BIOS Setup 5 Fault Diagnosis 6 Hardware Information 7 Distributed Configuration 8 Appendices A C Glossary , Index Release 04/02 Panel PC 670 Computing ...

  • Siemens PC 670 - page 2

    Safety Guidelines This manual contains notices which you should observe to ensure your own personal safety , as well as to protect the product and connected equipment. These notices are marked as follows according to the level of danger: ! Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious inju ...

  • Siemens PC 670 - page 3

    Correct Usage Please note the following: ! W arning The device may only be used for the application cases specified in the catalog and the technical description and may only be used in combination with third-party equipment and components recommended or approved by Siemens. Appropriate transport, and appropriate storage, installation and assembly , ...

  • Siemens PC 670 - page 4

    For your notes ...

  • Siemens PC 670 - page 5

    v Panel PC 670 Computing Unit, Equipment Manual Preface Purpose The SIMA TIC Panel PC 670 Computing Unit equipment manual is part of the SIMA TIC HMI documentation. It provides information for operators, mechanics, project engineers and maintenance personnel about the computing unit ’ s installation, functionality , operation and technical struct ...

  • Siemens PC 670 - page 6

    Preface Release 04/02 vi Panel PC 670 Computing Unit, Equipment Manual Notation The following conventions are used in this manual: Motor on T ext that is displayed on the operating unit is printed in Courier type face. Variable Symbolic names that stand for variable quantities that appear on the screen are printed in Courier italic type face. Scree ...

  • Siemens PC 670 - page 7

    Preface Release 04/02 vii Panel PC 670 Computing Unit, Equipment Manual Automation and Drives, Service & Support Available round the clock, worldwide: SIMA TIC Hotline Johnson City Nuremberg Singapore W orldwide (Nuremberg) T echnical Support (FreeContact) Local time: Mon.-Fri. 8:00 to 17:00 T elephone: +49 (180) 5050-222 Fax: +49 (180) 5050-22 ...

  • Siemens PC 670 - page 8

    Preface Release 04/02 viii Panel PC 670 Computing Unit, Equipment Manual SIMA TIC Customer Support Online Services The SIMA TIC Customer Support team offers you substantial additional information about SIMA TIC products via its online services: S General current information can be obtained – in the Internet unter http://www.siemens.com/simatic S ...

  • Siemens PC 670 - page 9

    ix Panel PC 670 Computing Unit, Equipment Manual Contents 1 Product Overview 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Advantages of the Computing Unit 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Safety Notes 1-4 . . . . . . . . . . . . . . . . . ...

  • Siemens PC 670 - page 10

    Contents Release 04/02 x Panel PC 670 Computing Unit, Equipment Manual 4.2 Installation of a Memory Extension 4-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Replacing the Backup Battery 4-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 Installation of Extension Modules 4-12 . . . . . . . . ...

  • Siemens PC 670 - page 11

    Contents Release 04/02 xi Panel PC 670 Computing Unit, Equipment Manual 7.4 Monitoring Functions 7-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4.1 Overview 7-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4.2 Signals on the front int ...

  • Siemens PC 670 - page 12

    Contents Release 04/02 xii Panel PC 670 Computing Unit, Equipment Manual ...

  • Siemens PC 670 - page 13

    1-1 Panel PC 670 Computing Unit, Equipment Manual Product Overview Chapter Overview In Section Y ou Will Find on Page 1.1 Advantages of the computing unit 1-2 1.2 Safety notes 1-4 1.3 Certificates, guidelines and declarations 1-8 1.4 Certification for USA, Canada and Australia 1-10 1 ...

  • Siemens PC 670 - page 14

    Product Overview Release 04/02 1-2 Panel PC 670 Computing Unit, Equipment Manual 1.1 Advantages of the Computing Unit Computing unit The computing unit serves as a basic component for the PC-based HMI devices (Panel PC) and, within the scope of special configurations, as a basis for customized devices. The computing unit is intended for use in indu ...

  • Siemens PC 670 - page 15

    Product Overview Release 04/02 1-3 Panel PC 670 Computing Unit, Equipment Manual Software equipment The computing unit is equipped with software which allows it to be used universally . It contains the operating system Windows NT 4.0, Windows 98 or Windows 2000. The computing unit additionally allows the use of: S SIMA TIC supplementary software S ...

  • Siemens PC 670 - page 16

    Product Overview Release 04/02 1-4 Panel PC 670 Computing Unit, Equipment Manual 1.2 Safety Notes ! Caution Please observe the safety notes on the back of the cover of this manual. Expansions to the Panel PC should only be carried out after having read Chapter 4 and the relevant safety notes. This device complies with the safety requirements in acc ...

  • Siemens PC 670 - page 17

    Product Overview Release 04/02 1-5 Panel PC 670 Computing Unit, Equipment Manual Mains supply When connecting the device, observe the relevant information provided in Chapter 2. Never connect or disconnect power cables or data transmission lines during a thunderstorm. In an emergency situation (for instance, damage to the housing, controls or power ...

  • Siemens PC 670 - page 18

    Product Overview Release 04/02 1-6 Panel PC 670 Computing Unit, Equipment Manual Country-Specific Notes For the USA and Canada: For operation in Canada and the United States, use CSA or UL-listed power cables. The connector must comply with the NEMA 5-15 specification. 120 V power supply A flexible cable with UL approval and CSA marking and the fol ...

  • Siemens PC 670 - page 19

    Product Overview Release 04/02 1-7 Panel PC 670 Computing Unit, Equipment Manual Batteries This unit contains batteries on the motherboard. The batteries may only be replaced by authorized, adequately trained personnel. When disposing of the batteries, observe the locally applicable laws on disposal of pollutants. ! Caution Improper replacement of ...

  • Siemens PC 670 - page 20

    Product Overview Release 04/02 1-8 Panel PC 670 Computing Unit, Equipment Manual 1.3 Certificates, Guidelines and Declarations CE identification The SIMA TIC product described in this manual fulfills the requirements to be awarded the CE identification. EMC guidelines Units with Power Supply 105W Power fulfill the requirements of EU Guideline “ 8 ...

  • Siemens PC 670 - page 21

    Product Overview Release 04/02 1-9 Panel PC 670 Computing Unit, Equipment Manual Observe installation guidelines The installation guidelines and safety notes specified in this manual must be observed when starting up and operating the system. Connection of periphery devices The requirements concerning interference immunity are met when periphery eq ...

  • Siemens PC 670 - page 22

    Product Overview Release 04/02 1-10 Panel PC 670 Computing Unit, Equipment Manual 1.4 Certification for USA, Canada and Australia Safety If the device bears one of the following marks, the corresponding approval has been awarded: Underwriters Laboratories (UL) complying with Standard UL 1950 (I.T .E) or complying with UL508 (IND.CONT .EQ) Underwrit ...

  • Siemens PC 670 - page 23

    Product Overview Release 04/02 1-1 1 Panel PC 670 Computing Unit, Equipment Manual EMC USA Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro ...

  • Siemens PC 670 - page 24

    Product Overview Release 04/02 1-12 Panel PC 670 Computing Unit, Equipment Manual Australia This product meets the requirements of the AS/NZS 3548 Norm. ...

  • Siemens PC 670 - page 25

    2-1 Panel PC 670 Computing Unit, Equipment Manual Starting Up the Computing Unit Chapter Overview In Section Y ou Will Find on Page 2.1 Unpacking and checking the computing unit 2-2 2.2 Installing the computing unit 2-3 2.3 Ensuring Readiness for Service 2-7 2.4 Transport 2-9 2 ...

  • Siemens PC 670 - page 26

    Starting Up the Computing Unit Release 04/02 2-2 Panel PC 670 Computing Unit, Equipment Manual 2.1 Unpacking and Checking the Computing Unit Unpacking the computing unit Unpack the item delivered to you as follows: 1. Remove the packaging. 2. Do not throw the original packaging away . Keep it in case you have to transport your PC at some time in th ...

  • Siemens PC 670 - page 27

    Starting Up the Computing Unit Release 04/02 2-3 Panel PC 670 Computing Unit, Equipment Manual 2.2 Installing the Computing Unit The unit delivered is particularly suited for installation in consoles, cabinets and panels. The computing units with AC power supply meet the requirements of the fire protection housing complying with EN60950. It can the ...

  • Siemens PC 670 - page 28

    Starting Up the Computing Unit Release 04/02 2-4 Panel PC 670 Computing Unit, Equipment Manual 297 80 267 11 Figure 2-1 Dimension drawings for installation of the computing unit (device without CD-ROM drive) The computing unit contains a CD-ROM or CD-RW/DVD drive, depending on the unit version. The installation depth of the computing unit is increa ...

  • Siemens PC 670 - page 29

    Starting Up the Computing Unit Release 04/02 2-5 Panel PC 670 Computing Unit, Equipment Manual Permissible installation positions for the computing unit complying with UL1950/EN60950/CSA22. 2 No. 950 An angle of inclination of ± 20 _ is allowed installation position. Position 1 (preferred position) Position 2 *) Position 3 (desktop) Position 4 (co ...

  • Siemens PC 670 - page 30

    Starting Up the Computing Unit Release 04/02 2-6 Panel PC 670 Computing Unit, Equipment Manual Additional permissible installation position for the computing unit complying with UL508/CSA 22.2 No. 142 An installation angle of ± 15 _ is permitted in this position. Position 5 (interfaces at bottom) Note The possible installation locations for the co ...

  • Siemens PC 670 - page 31

    Starting Up the Computing Unit Release 04/02 2-7 Panel PC 670 Computing Unit, Equipment Manual 2.3 Ensuring Readiness for Service Measures for equipotential Low-resistance grounding connections ensure that the user of the installation is protected against electric shock (for example, if a short-circuit occurs or if there are defects in the system). ...

  • Siemens PC 670 - page 32

    Starting Up the Computing Unit Release 04/02 2-8 Panel PC 670 Computing Unit, Equipment Manual The AC power supply of the computing unit is designed for 120/230/240 V mains supplies. The power supply has a wide range input. There is no need to adjust the voltage range. The DC power supply of the computing unit is designed for 24 V mains supplies. O ...

  • Siemens PC 670 - page 33

    Starting Up the Computing Unit Release 04/02 2-9 Panel PC 670 Computing Unit, Equipment Manual 2.4 T ransport Shipping Despite the robust design of the computing unit, its built-in components are sensitive to severe vibrations and shock. Therefore, protect the computing unit from severe mechanical stress during transport. Only the original packing ...

  • Siemens PC 670 - page 34

    Starting Up the Computing Unit Release 04/02 2-10 Panel PC 670 Computing Unit, Equipment Manual ...

  • Siemens PC 670 - page 35

    3-1 Panel PC 670 Computing Unit, Equipment Manual Connecting and Switching on the Computing Unit Chapter Overview In Section Y ou Will Find on Page 3.1 View of Interface Side 3-2 3.2 View of Drive Side 3-5 3.3 Connecting Peripheral Devices 3-6 3.4 Working with PC Cards 3-10 3.5 Drives 3-13 3.6 Backup battery 3-17 3.7 Using the Computing Unit in a S ...

  • Siemens PC 670 - page 36

    Connecting and Switching on the Computing Unit Release 04/02 3-2 Panel PC 670 Computing Unit, Equipment Manual 3.1 V iew of Interface Side 12 3 4 56 7 8 9 10 11 12 13 Figure 3-1 Ports 1 Mouse PS/2 socket for connecting a PS/2 mouse. 2 COM1 V .24 /MODEM /PLC The COM 1(TTY) interface can be used to connect e.g. S5 programmable controller (PLC). By im ...

  • Siemens PC 670 - page 37

    Connecting and Switching on the Computing Unit Release 04/02 3-3 Panel PC 670 Computing Unit, Equipment Manual 8 Ethernet RJ 45 Ethernet connection. The Ethernet network is a local network with a bus structure for data communication with data transmission rates of 10 or 100 megabits per second (mbps). 9 PROFIBUS/MPI Using the potential isolated PRO ...

  • Siemens PC 670 - page 38

    Connecting and Switching on the Computing Unit Release 04/02 3-4 Panel PC 670 Computing Unit, Equipment Manual VGA interface Please observe the following note on operating a flat display and an external monitor: Note The default setting of the display is simultaneous operation of a flat display and an external monitor . If no front display element ...

  • Siemens PC 670 - page 39

    Connecting and Switching on the Computing Unit Release 04/02 3-5 Panel PC 670 Computing Unit, Equipment Manual 3.2 V iew of Drive Side 12 4 3 5 Figure 3-2 Drive side 1 Unit fan The air vents for the unit fan are located here. Caution The air vents must never be covered up, otherwise there is a risk of overheating. 2 Rating plate The rating plate co ...

  • Siemens PC 670 - page 40

    Connecting and Switching on the Computing Unit Release 04/02 3-6 Panel PC 670 Computing Unit, Equipment Manual 3.3 Connecting Periphery Units Note Make sure the components you insert exhibit industrial compatibility when connecting peripheral devices Printer connection via the parallel interface To connect your print er, perform the following st ep ...

  • Siemens PC 670 - page 41

    Connecting and Switching on the Computing Unit Release 04/02 3-7 Panel PC 670 Computing Unit, Equipment Manual Printer connection via the parallel serial interface Alternatively, you can connect your printer via a serial COM interface to the computing unit. You will find information on how to adapt and set your port and on the connecting cable you ...

  • Siemens PC 670 - page 42

    Connecting and Switching on the Computing Unit Release 04/02 3-8 Panel PC 670 Computing Unit, Equipment Manual Serial mouse connection You can connect a serial mouse to the serial por t COM 2. To operate a serial mouse, you have to install and assign paramet ers to the suitable mouse driver. To do this, please refer to the descri pt ion of your mou ...

  • Siemens PC 670 - page 43

    Connecting and Switching on the Computing Unit Release 04/02 3-9 Panel PC 670 Computing Unit, Equipment Manual USB device connection Individual or several USB devices can be connected to the USB interfaces. S Plug in the USB device connector into one of the USB interfaces. The device is detected by the Plug and Play operating system. Any necessary ...

  • Siemens PC 670 - page 44

    Connecting and Switching on the Computing Unit Release 04/02 3-10 Panel PC 670 Computing Unit, Equipment Manual 3.4 W orking with PC Cards PC cards Card bus cards (32 bit) and PCMCIA cards (16 bit) can be operated in the PC card interface. The computing unit is equipped with a PC card interf ace. Communic ation modules for MODE M, FAX/MO DEM, ISDN, ...

  • Siemens PC 670 - page 45

    Connecting and Switching on the Computing Unit Release 04/02 3-1 1 Panel PC 670 Computing Unit, Equipment Manual ! Caution Always discharge your body ’ s static charge before inserting or removing Cardbus/PC cards by briefly touching a grounded object (refer also the ESD Guideline, Appendix B). Damage could occur if you do not. Note Peak currents ...

  • Siemens PC 670 - page 46

    Connecting and Switching on the Computing Unit Release 04/02 3-12 Panel PC 670 Computing Unit, Equipment Manual Installation von PC cards Observe the following points when you install these cards: Note Depending o n the configuration of the computing unit, it could be that there are no free interrupts for the operation of PC cards. The interrupts r ...

  • Siemens PC 670 - page 47

    Connecting and Switching on the Computing Unit Release 04/02 3-13 Panel PC 670 Computing Unit, Equipment Manual 3.5 Drives The computing unit is equipped with a 3.5 ” floppy disk drive or LS 240 drive and a 3.5 ” hard disk drive as standard equipment. 3.5.1 Floppy disk drive The floppy disk drive can be used to store programs and data on disks ...

  • Siemens PC 670 - page 48

    Connecting and Switching on the Computing Unit Release 04/02 3-14 Panel PC 670 Computing Unit, Equipment Manual Handling LS240 drive disks The disks are inserted in the disk drive as illustrated below according to the installation position: Access light Eject button Eject button Access light Drill hole for emergency ejection (LS240 only) Figure 3-8 ...

  • Siemens PC 670 - page 49

    Connecting and Switching on the Computing Unit Release 04/02 3-15 Panel PC 670 Computing Unit, Equipment Manual Notes on using the LS240 superdisks The LS240 drive supports the use of standard 3.5 ” disks with 1.44 Mbyte capacity as well as superdisks with a capacity up to 240 Mbyte. The track density of superdisks is 10 m m as compared to 120 m ...

  • Siemens PC 670 - page 50

    Connecting and Switching on the Computing Unit Release 04/02 3-16 Panel PC 670 Computing Unit, Equipment Manual 3.5.3 Hard disk drive The hard disk is used to store large quantities of data. It is installed on a vibration-damped mounting that is easy to replace. ! Caution Danger of data being lost and the drive damaged Drives are very sensitive to ...

  • Siemens PC 670 - page 51

    Connecting and Switching on the Computing Unit Release 04/02 3-17 Panel PC 670 Computing Unit, Equipment Manual Caution CD-ROM drives are sensitive to unacceptable vibrations. During operation, vibrations might damage the drive and/or the data medium. Additional software In order to use the full functional scope of the DVD-ROM/CD-RW drive, addition ...

  • Siemens PC 670 - page 52

    Connecting and Switching on the Computing Unit Release 04/02 3-18 Panel PC 670 Computing Unit, Equipment Manual 3.7 Using the Computing Unit in a SIMA TIC S5 Network Point-to-point connection This section describes the options for connecting your computing unit to a programming unit or an S5 programmable controller in a point-to-point connection. A ...

  • Siemens PC 670 - page 53

    Connecting and Switching on the Computing Unit Release 04/02 3-19 Panel PC 670 Computing Unit, Equipment Manual Connecting the computing unit to an S5 PLC You can connect the computing unit to a SIMA T IC S5 pr ogr am mable controller using the COM 1/TTY interface. COM 1 (Socket) Figure 3-9 Connection to an S5 Programmable Controller T o connect th ...

  • Siemens PC 670 - page 54

    Connecting and Switching on the Computing Unit Release 04/02 3-20 Panel PC 670 Computing Unit, Equipment Manual Connecting the computing unit via an adapter An adapter is available for connecting the computing unit to the PLC with earlier standar d connecting cables. T able 3-1 Adapters for connecting the computing unit Interface Connection Connect ...

  • Siemens PC 670 - page 55

    Connecting and Switching on the Computing Unit Release 04/02 3-21 Panel PC 670 Computing Unit, Equipment Manual Connecting the computing unit to programming units (TTY) In order to connect the computing unit, connect the corresponding connection cable to the TTY interf ace. T able 3-2 Connecting the computing unit to other programming units Interfa ...

  • Siemens PC 670 - page 56

    Connecting and Switching on the Computing Unit Release 04/02 3-22 Panel PC 670 Computing Unit, Equipment Manual 3.8 Using the Computing Unit in a SIMA TIC S7 Network (MPI/DP) Connecting an S7 PLC via the MPI/DP interface Using the potential isolated*) MPI/ DP interface, the comput ing unit can be connected to a SIM A T I C S7 PLC or a PROFIB US net ...

  • Siemens PC 670 - page 57

    Connecting and Switching on the Computing Unit Release 04/02 3-23 Panel PC 670 Computing Unit, Equipment Manual MPI/PROFIBUS-DP network Up to 32 devices (PCs, program ming units or PLCs) can be connec t ed to the MPI / DP interface to form a network segment. The phy sical connection to the MPI/ PRO FI BUS-DP network is via an isol at ed RS485 inter ...

  • Siemens PC 670 - page 58

    Connecting and Switching on the Computing Unit Release 04/02 3-24 Panel PC 670 Computing Unit, Equipment Manual 3.9 Networking the Computing Unit and Other Nodes via PROFIBUS Networking the computing unit via PROFIBUS PROF IB US is an open and robust bus syst em for industrial use. It can be used to configure networks with up to 32 nodes per segmen ...

  • Siemens PC 670 - page 59

    Connecting and Switching on the Computing Unit Release 04/02 3-25 Panel PC 670 Computing Unit, Equipment Manual 3.10 Networking Computing Unit and Other Computers via Industrial Ethernet Networking the computing unit via Industrial Ethernet The RJ45 Ethernet interface is a T wisted Pair (TP) interface with a data transmissin rate of 10/100 Mbaud. T ...

  • Siemens PC 670 - page 60

    Connecting and Switching on the Computing Unit Release 04/02 3-26 Panel PC 670 Computing Unit, Equipment Manual ...

  • Siemens PC 670 - page 61

    4-1 Panel PC 670 Computing Unit, Equipment Manual Maintaining and Extending the Computing Unit Chapter overview You can enhance the functionality of your computing unit by installing additional main memory. This chapter describes how to expand your computing unit. Please observe the safety notes it contains. In Section Y ou Will Find on Page 4.1 Op ...

  • Siemens PC 670 - page 62

    Maintaining and Extending the Computing Unit Release 04/02 4-2 Panel PC 670 Computing Unit, Equipment Manual 4.1 Opening the Unit 4.1.1 Conditions The device is designed for easy maintenance so that any work that may be necessary can be done quickly and economically. Caution The electronic components on the printed circuit boards are extremely sens ...

  • Siemens PC 670 - page 63

    Maintaining and Extending the Computing Unit Release 04/02 4-3 Panel PC 670 Computing Unit, Equipment Manual Before opening the device Note the following rules before opening the device: S Before you disconnect the power supply cable, discharge the electrostatic charge on your body . Y ou can do this by briefly touching the mounting plate for the i ...

  • Siemens PC 670 - page 64

    Maintaining and Extending the Computing Unit Release 04/02 4-4 Panel PC 670 Computing Unit, Equipment Manual 4.1.2 Opening the computing unit To open the computing unit, perform the following steps: 1. T urn off the computing unit, pull out the mains connector and remove all interconnecting cables and connecting cables from the device, including th ...

  • Siemens PC 670 - page 65

    Maintaining and Extending the Computing Unit Release 04/02 4-5 Panel PC 670 Computing Unit, Equipment Manual 4.1.3 Functional Units Visible After Opening the Device View The function units become visible after removing the top cover of the unit and removing the hard disk module. Power supply unit Processor Wiring backplane Memory expansion module D ...

  • Siemens PC 670 - page 66

    Maintaining and Extending the Computing Unit Release 04/02 4-6 Panel PC 670 Computing Unit, Equipment Manual 4.1.4 Motherboard The motherboard is the heart of the computing unit. Here, data are processed and stored, and interfaces and device I/Os are controlled. X44 X400 X402 X401 S1 X1 X20 X19 X700 X29 X28 X128 X71 X70 X10 X500 X600 X40 X1 1 X9 X6 ...

  • Siemens PC 670 - page 67

    Maintaining and Extending the Computing Unit Release 04/02 4-7 Panel PC 670 Computing Unit, Equipment Manual Components on the motherboard The following components are located on the computing unit: Number Functions X1 Processor module with heat sink X3 IDE connector for CD-ROM X4 IDE connector for 2.5 ” hard disk X5 Floppy disk cable connector X ...

  • Siemens PC 670 - page 68

    Maintaining and Extending the Computing Unit Release 04/02 4-8 Panel PC 670 Computing Unit, Equipment Manual 4.2 Installation of a Memory Extension Standard memory The motherboard has 2 slots for 144 pin SO DIMM memory modules. This allows you to expand the memory capacity of your computing unit to 512 Mbytes. One or two modules can be equipped. Me ...

  • Siemens PC 670 - page 69

    Maintaining and Extending the Computing Unit Release 04/02 4-9 Panel PC 670 Computing Unit, Equipment Manual ! Caution The electronic components on the printed circuit boards are extremely sensitive to electrostatic discharge. Certain precautionary measures, therefore, have to be taken when handling them. These measures are explained in the guideli ...

  • Siemens PC 670 - page 70

    Maintaining and Extending the Computing Unit Release 04/02 4-10 Panel PC 670 Computing Unit, Equipment Manual 4.3 Replacing the Backup Battery Battery power supply for real-time clock and configuration A backup battery (3.6 V lithium battery) powers the real-time clock even after the unit has been turned of f. In addition to the time of day , all t ...

  • Siemens PC 670 - page 71

    Maintaining and Extending the Computing Unit Release 04/02 4-1 1 Panel PC 670 Computing Unit, Equipment Manual Backup battery Figure 4-5 Position of the backup battery ! Caution Danger of damage! Only replace the lithium battery with an identical battery or with a type recommended by the manufacturer (Order No: W79084-E1003-B1). If possible, return ...

  • Siemens PC 670 - page 72

    Maintaining and Extending the Computing Unit Release 04/02 4-12 Panel PC 670 Computing Unit, Equipment Manual 4.4 Installation of Extension Modules Notes on the boards The computing unit is designed for the use of cards as per the A T/PCI specification. The dimensions of the cards must not exceed the stated dimensions. If the height is exceeded, co ...

  • Siemens PC 670 - page 73

    Maintaining and Extending the Computing Unit Release 04/02 4-13 Panel PC 670 Computing Unit, Equipment Manual 174.63 mm 106.68 mm 8.19 mm 6.875 ” 0.322 ” 4.2 ” Figure 4-8 Short PCI card (5 V) 265 mm 10.48 ” 106.68 mm 4.2 ” 8.19 mm 0.322 ” Figure 4-9 Long PCI card (5 V) Note on long PCI cards Before long PCI cards can be inserted in the ...

  • Siemens PC 670 - page 74

    Maintaining and Extending the Computing Unit Release 04/02 4-14 Panel PC 670 Computing Unit, Equipment Manual 4.4.1 Removing and installing the module retainer plates The module retainer plate is attached to the housing by a screw . It has three slits, through which the slide elements are inserted. T o change the battery , perform the following ste ...

  • Siemens PC 670 - page 75

    Maintaining and Extending the Computing Unit Release 04/02 4-15 Panel PC 670 Computing Unit, Equipment Manual Adjusting the module retainer plate Proceed as follows to install the module retainer plate. 1. Insert the slide element through the guide slit until it is resting firmly on the module. The module must now be introduced into the notch. Caut ...

  • Siemens PC 670 - page 76

    Maintaining and Extending the Computing Unit Release 04/02 4-16 Panel PC 670 Computing Unit, Equipment Manual 4.4.2 Removing and installing an ISA/PCI module T o change the battery , perform the following steps: 1. Open the housing as described in section 4.1. 2. Disconnect all the connectors from the expansion module and note their assignment. 3. ...

  • Siemens PC 670 - page 77

    Maintaining and Extending the Computing Unit Release 04/02 4-17 Panel PC 670 Computing Unit, Equipment Manual 4.5 Removing and Installing Drives The basic configuration of the computing unit includes a 3.5 ” floppy disk drive and a 3.5 ” hard disk drive. An LS 240 drive is possible for custom solutions. 4.5.1 Removing and installing the hard di ...

  • Siemens PC 670 - page 78

    Maintaining and Extending the Computing Unit Release 04/02 4-18 Panel PC 670 Computing Unit, Equipment Manual Figure 4-13 Hard disk drive, with holder , removed ...

  • Siemens PC 670 - page 79

    Maintaining and Extending the Computing Unit Release 04/02 4-19 Panel PC 670 Computing Unit, Equipment Manual 4.5.2 Removing and installing a CD-ROM drive Depending on the hardware configuration of the device, a CD-ROM drive is installed on the computing unit. The installation depth of the computing unit is increased by 21 mm as a result of its ins ...

  • Siemens PC 670 - page 80

    Maintaining and Extending the Computing Unit Release 04/02 4-20 Panel PC 670 Computing Unit, Equipment Manual 4.5.3 Removing and installing the disk drive 1. Open the housing as described in Chapter 4.1. 2. Remove the drive mounting as described in section 4.5.1. 3. Undo the interlocking of the controller flexible cable on the motherboard and pull ...

  • Siemens PC 670 - page 81

    Maintaining and Extending the Computing Unit Release 04/02 4-21 Panel PC 670 Computing Unit, Equipment Manual 4.5.4 Removing and installing the LS 240 drive T o remove and install the LS240 drive, perform the same steps as for installing the floppy disk drive. 1. Open the housing as described in Chapter 4.1. 2. Remove the drive mounting as describe ...

  • Siemens PC 670 - page 82

    Maintaining and Extending the Computing Unit Release 04/02 4-22 Panel PC 670 Computing Unit, Equipment Manual 4.6 Removing and Installing the Power Supply 1. Open the housing as described in section 4.1. 2. Remove the drive mounting as described in section 4.5.1. 3. Remove the 3 screws from the cover of the power supply unit from the housing. 4. Di ...

  • Siemens PC 670 - page 83

    Maintaining and Extending the Computing Unit Release 04/02 4-23 Panel PC 670 Computing Unit, Equipment Manual 4.7 Removing and Installing the Bus Board 1. Open the housing as described in section 4.1. 2. Remove all the modules from their slots (perform the steps described in section 4.4.2). 3. Remove the drive mounting as described in section 4.5.1 ...

  • Siemens PC 670 - page 84

    Maintaining and Extending the Computing Unit Release 04/02 4-24 Panel PC 670 Computing Unit, Equipment Manual 4.8 Removing and Installing the Motherboard 1. Open the housing as described in section 4.1. 2. Remove all the modules from their slots (perform the steps described in section 4.4.2). 3. Remove the drive mounting as described in section 4.5 ...

  • Siemens PC 670 - page 85

    Maintaining and Extending the Computing Unit Release 04/02 4-25 Panel PC 670 Computing Unit, Equipment Manual 4.9 Removing and Installing the Fan The computing unit is cooled by means of a fan, which extracts hot air out of the housing. 1. Open the housing as described in section 4.1. 2. Disconnect the fan cable connector from the motherboard. 3. T ...

  • Siemens PC 670 - page 86

    Maintaining and Extending the Computing Unit Release 04/02 4-26 Panel PC 670 Computing Unit, Equipment Manual 4.10 Processor Upgrade Y ou can boost the performance capability of your computing unit by installing other processors. Proceed as follows to replace the processor (the numbers in brackets relate to Figure 4-21): 1. Disconnect the fan cable ...

  • Siemens PC 670 - page 87

    Maintaining and Extending the Computing Unit Release 04/02 4-27 Panel PC 670 Computing Unit, Equipment Manual 4.1 1 Reset button A hardware reset is initiated by means of the Reset button on your device. The computing unit is restarted. On the computing unit, the Reset button is located on the drive side beside the floppy disk drive. The Reset butt ...

  • Siemens PC 670 - page 88

    Maintaining and Extending the Computing Unit Release 04/02 4-28 Panel PC 670 Computing Unit, Equipment Manual ...

  • Siemens PC 670 - page 89

    5-1 Panel PC 670 Computing Unit, Equipment Manual Configuring the Computing Unit in BIOS Setup Chapter Overview In this chapter, you will learn how to configure your comput ing unit. You need to do this if you want to change your sy st em by adding, remov ing, or exchanging an extension board, mem ory expansion module, or by replacing a system modu ...

  • Siemens PC 670 - page 90

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-2 Panel PC 670 Computing Unit, Equipment Manual 5.1 Modifying the Device Configuration with SETUP Changing the Device Configuration The device configuration of your computing unit is preset for working with the software supplied to you. Y ou should only modify the preset values if you hav ...

  • Siemens PC 670 - page 91

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-3 Panel PC 670 Computing Unit, Equipment Manual Screen Display Following Power On For example, the d e f au l t s e t t in g o f y o u r computing unit w i l l d i s p l a y t h e f o l l o w i n g figure on the display on power on: Phoenix BIOS 4.0 A5E00123801–ES02 Copyright 1985-2001 ...

  • Siemens PC 670 - page 92

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-4 Panel PC 670 Computing Unit, Equipment Manual Menu items After BIOS Setup has started, the following dialog box appears on the screen: Menu bar Operator control bar Selectable submenu Title bar PhoenixBIOS Setup Utility Item Specific Help System Time: ESC Exit <T ab>, <Shift-T ...

  • Siemens PC 670 - page 93

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-5 Panel PC 670 Computing Unit, Equipment Manual 5.1.1 Menu Main Selectable submenu PhoenixBIOS Setup Utility Item Specific Help System Time: ESC Exit <T ab>, <Shift-T ab>, or System Date: Select Item Select Menu + / – Select Change V alues Sub-Menu F9 F10 Setup Defaults Save ...

  • Siemens PC 670 - page 94

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-6 Panel PC 670 Computing Unit, Equipment Manual System T ime und System Date Time and date System Time and System Dat e indi cate the current values. Once you have selected the appropriate opt ion, you can use the [+] and [ – ] keys to modi fy the time setti ng Hour:Minute:Second and th ...

  • Siemens PC 670 - page 95

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-7 Panel PC 670 Computing Unit, Equipment Manual Primary Master , Primary Slave, Secondary Master, Secondary Slave The system jumps to the followi ng submenu when you select this type of menu field: PhoenixBIOS Setup Utility Item Specific Help T ype: ESC Exit Select Item Select Menu + / ? ...

  • Siemens PC 670 - page 96

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-8 Panel PC 670 Computing Unit, Equipment Manual Multi Sector T ransfer field I n t h e box Multi Sector -T ransfer the number of blocks (sect ors) are def ined that will be tr ansmit ted with one int errupt . The value depends on the drive and should be set only by setting the T ype field ...

  • Siemens PC 670 - page 97

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-9 Panel PC 670 Computing Unit, Equipment Manual ” Memory Cache ” Submenu The following pop- up menu appear s when you select the submenu “ Me mory cache ” in the main menu: PhoenixBIOS Setup Utility Item Specific Help System Time: ESC Exit System Date: Select Item Select Menu + / ...

  • Siemens PC 670 - page 98

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-10 Panel PC 670 Computing Unit, Equipment Manual Submenu ” Boot Options ” The following submenu appears when you select the option “ Boot Opt ions ” in the main menu: PhoenixBIOS Setup Utility Item Specific Help QuickBoot Mode: ESC Exit Select Item Select Menu + / – Select Chang ...

  • Siemens PC 670 - page 99

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-1 1 Panel PC 670 Computing Unit, Equipment Manual Floppy check The floppy head is stepped inward and then back to its original position during the system run-up phase. This test is useful because it reinitializes the drive. Summary screen The most important system parameters are displayed ...

  • Siemens PC 670 - page 100

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-12 Panel PC 670 Computing Unit, Equipment Manual Submenu ” Keyboard Features ” The following submenu appears if you select the “ Keyboard Features ” field in the main menu: PhoenixBIOS Setup Utility Item Specific Help NumLock: ESC Exit Selects Power-On state for NumLock on next bo ...

  • Siemens PC 670 - page 101

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-13 Panel PC 670 Computing Unit, Equipment Manual Submenu ” Hardware Options ” The following submenu appears when you select the “ Hardware Options ” field in the main menu: PhoenixBIOS Setup Utility Item Specific Help PCI – MPI / DP: ESC Exit Select Item Select Menu + / – Sele ...

  • Siemens PC 670 - page 102

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-14 Panel PC 670 Computing Unit, Equipment Manual Entr y Meaning Card bus / PCMCIA Slot [ Disabled ] Release the Cardbus / PCMCIA interfaces is disabled. [ Enabled ] The resources are managed by the BIOS PCI plug and play mechanism. SafeCard functions [ Enabled ] On board monitoring functi ...

  • Siemens PC 670 - page 103

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-15 Panel PC 670 Computing Unit, Equipment Manual 5.1.2 Men ü Advanced Menu structure PhoenixBIOS Setup Utility Item Specific Help ESC Exit Reset Configuration Data: Select Item Select Menu + / – Select Change V alues Sub-Menu F9 F10 Setup Defaults Save and Exit COM/LPT Configuration Fl ...

  • Siemens PC 670 - page 104

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-16 Panel PC 670 Computing Unit, Equipment Manual Large Disk Access Mode [DOS] The drive tables are adapted for DOS access operations in accordance with Enhanced IDE. [OTHER] The tables are not adapted. Memory Gap at 15 MByte [Disabled] The complete onboard RAM memory is available. [Enable ...

  • Siemens PC 670 - page 105

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-17 Panel PC 670 Computing Unit, Equipment Manual Printer Port Internal LPT1 Mode: Use this setting to set the operating mode of the printer interface. Refer to the table below to ensure that the setting matches the printer connected to the printer port. Sett abl e Mode Featur es Output On ...

  • Siemens PC 670 - page 106

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-18 Panel PC 670 Computing Unit, Equipment Manual PCI Configuration Submenu PhoenixBIOS Setup Utility Item Specific Help ESC Exit Select Item Select Menu + / – Select Change V alues Sub-Menu F9 F10 Setup Defaults Save and Exit Enter Help F1 Advanced PCI Configuration Setup items for conf ...

  • Siemens PC 670 - page 107

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-19 Panel PC 670 Computing Unit, Equipment Manual Option ROM Scan: [Enabled] The option ROM of the PCI module (if present) is enabled [Disabled] The option ROM of a PCI module is disabled. Enable Master: [Enabled] This slot can assume the PCI master function [Disabled] This slot can only o ...

  • Siemens PC 670 - page 108

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-20 Panel PC 670 Computing Unit, Equipment Manual “ PCI IRQ line ” Field PhoenixBIOS Setup Utility Item Specific Help ESC Exit Select Item Select Menu + / – Select Change V alues Sub-Menu F9 F10 Setup Defaults Save and Exit Enter Help F1 Advanced PCI Configuration Reserves the specif ...

  • Siemens PC 670 - page 109

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-21 Panel PC 670 Computing Unit, Equipment Manual Submenu “ Video Adapter Settings ” PhoenixBIOS Setup Utility Item Specific Help ESC Exit Select Item Select Menu + / – Select Change V alues Sub-Menu F9 F10 Setup Defaults Save and Exit Enter Help F1 Advanced V ideo Adapter Settings O ...

  • Siemens PC 670 - page 110

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-22 Panel PC 670 Computing Unit, Equipment Manual 5.1.3 Men ü Security Overview You can only edit the fields enclosed in squar e brackets. In order to protect your comput ing unit against illegal use it is possible to enter two passwords . Wit h the supervisor passwor d, the setup access ...

  • Siemens PC 670 - page 111

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-23 Panel PC 670 Computing Unit, Equipment Manual Password on boot [Disabled] No password required for system boot. [Enabled] Supervisor or user password must be entered for system boot. Fixed disk boot Sector [Normal] All types of hard-disk access are permitted. [Write protect] No operati ...

  • Siemens PC 670 - page 112

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-24 Panel PC 670 Computing Unit, Equipment Manual 5.1.4 Menu Power Overview This menu has the following structure. PhoenixBIOS Setup Utility Item Specific Help ESC Exit Select Item Select Menu + / – Select Change V alues Sub-Menu F9 F10 Setup Defaults Save and Exit Power Savings: Enter H ...

  • Siemens PC 670 - page 113

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-25 Panel PC 670 Computing Unit, Equipment Manual Hard Disk Timeout [Disabled] The hard disk does not shut down. [10, 15, 30, 60] Time since the last hard-disk access, the hard disk is shut down. On the next access the hard disk will be activated again with a short delay . 5.1.5 Menu Boot- ...

  • Siemens PC 670 - page 114

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-26 Panel PC 670 Computing Unit, Equipment Manual Groups marked + contain more than one device. When you select a group marked in this way , hit Enter to view the list of devices in the group. See the figure below for an illustration: PhoenixBIOS Setup Utility Item Specific Help ESC Exit S ...

  • Siemens PC 670 - page 115

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-27 Panel PC 670 Computing Unit, Equipment Manual 5.1.6 Menu V ersion This menu contains the inf orm at ion you will have to quot e when you send us technic al questions about your sys tem . PhoenixBIOS Setup Utility Item Specific Help ESC Exit Select Item Select Menu + / – Select Change ...

  • Siemens PC 670 - page 116

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-28 Panel PC 670 Computing Unit, Equipment Manual 5.1.7 Menu Exit The Exit Menu The setup program is always term inated using this menu. PhoenixBIOS Setup Utility Item Specific Help ESC Exit Select Item Select Menu + / – Select Change V alues Sub-Menu F9 F10 Setup Defaults Save and Exit ...

  • Siemens PC 670 - page 117

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-29 Panel PC 670 Computing Unit, Equipment Manual 5.1.8 Setup default settings Documenting your device configuration If you have made any modifications to the default Set up settings, you can ent er them in the following table. You can then ref er to these entries if you need to make any h ...

  • Siemens PC 670 - page 118

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-30 Panel PC 670 Computing Unit, Equipment Manual System Parameters Y our Entries Standard Settings Cardbus/PCMCIA Slot Enabled SafeCard Functions Enabled Legacy USB Support Disabled CR T/LCD selection SIMUL T AN LCD Screensize Expanded DSTN Contrast 154 PS2 Mouse Enabled Advanced COM/LPT ...

  • Siemens PC 670 - page 119

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-31 Panel PC 670 Computing Unit, Equipment Manual System Parameters Y our Entries Standard Settings Floppy disk controller Enabled Local Bus IDE adapter Both Large Disk Access Mode DOS Hard Disk Pre-Delay Disabled Memory Gap at 15 MByte Disabled Video Adapter Settings Frame Buffer Size 8 M ...

  • Siemens PC 670 - page 120

    Configuring the Computing Unit in BIOS Setup Release 04/02 5-32 Panel PC 670 Computing Unit, Equipment Manual 5.2 Configure PC-Card interface Y ou can obtain the software you require for using PC cards under MS DOS, such as S Socket Services S Card Services S Client Drivers S Flash File System can be obtained from the nearest Siemens sales office o ...

  • Siemens PC 670 - page 121

    6-1 Panel PC 670 Computing Unit, Equipment Manual Fault Diagnosis Chapter overview This chapter provides information on localizing problems which frequently occur and how to clear them. Note Please refer to the operating system documentation with regard to error messages concerning the operating system. In Section Y ou Will Find on Page 6.1 Problem ...

  • Siemens PC 670 - page 122

    Fault Diagnosis Release 04/02 6-2 Panel PC 670 Computing Unit, Equipment Manual 6.1 Problems Using External Modules Fault screen Computing unit crashes during boot routine. Cause The following causes are possible: – Double assignment of input/output addresses, – Double assignment of hardware interrupts and/or DMA channels, – Signal frequencie ...

  • Siemens PC 670 - page 123

    Fault Diagnosis Release 04/02 6-3 Panel PC 670 Computing Unit, Equipment Manual 6.2 External Screen Remains Dark Cause/Remedy The following causes are possible: Monitor is switched off S Switch on the screen. Screen has been dimmed S Press any key on the keyboard. Brightness control set to dark S Set the screen brightness control lighter . Please r ...

  • Siemens PC 670 - page 124

    Fault Diagnosis Release 04/02 6-4 Panel PC 670 Computing Unit, Equipment Manual 6.3 Display on the External Screen Does Not Appear or Scrolls Cause/Remedy The incorrect line frequency and/or resolution is set for the screen or the application program. S Exit from the application program. If the fault continues to occur after terminating the program ...

  • Siemens PC 670 - page 125

    Fault Diagnosis Release 04/02 6-5 Panel PC 670 Computing Unit, Equipment Manual 6.5 Computing Unit T ime and/or Date are Not Correct Remedy Correct the time and date in the Setup menu. Press F2 during the boot routine to call in the Setup menu (refer to Chapter 5). Note If the date and time remain incorrect after switching the unit off and on again ...

  • Siemens PC 670 - page 126

    Fault Diagnosis Release 04/02 6-6 Panel PC 670 Computing Unit, Equipment Manual 6.7 Error Message Appears on the Screen/Display Error messages The error messages issued by the system BIOS are listed below . Refer to the relevant program manuals in the case of error messages issued by the operating system or programs. Press F2 during the boot routin ...

  • Siemens PC 670 - page 127

    Fault Diagnosis Release 04/02 6-7 Panel PC 670 Computing Unit, Equipment Manual Error message on screen Significance/Advice Operating system not found Possible causes: No operating system available W rong drive triggered (disk in drive A/B) W rong active boot partition W rong drive entries in SETUP Previous boot incomplete Default configuration use ...

  • Siemens PC 670 - page 128

    Fault Diagnosis Release 04/02 6-8 Panel PC 670 Computing Unit, Equipment Manual 6.8 Computing Unit Self-T est Prior to Booting After switching on the SIMA TIC PC a self-test is initiated (POST = Power On Self T est). If errors are detected during the POST , the corresponding sequence of POST beeps (beep code) are issued. Each beep code consists of ...

  • Siemens PC 670 - page 129

    Fault Diagnosis Release 04/02 6-9 Panel PC 670 Computing Unit, Equipment Manual POST codes The POST codes in order of occurrence: Display (hex) Meaning Description 02 TP_VERIFY_REAL T est whether the CPU is in real mode 1C TP_RESET_PIC Reset the interrupt controller 12 TP_REST ORE_CRO Restore the controller register 13 TP_PCI_BM_RESET Reset the PCI ...

  • Siemens PC 670 - page 130

    Fault Diagnosis Release 04/02 6-10 Panel PC 670 Computing Unit, Equipment Manual Display (hex) Description Meaning 46 TP_COPYRIGHT T est the copyright 49 TP_PCI_INIT Initialize the PCI interface 48 TP_CONFIG Check the configuration 4A TP_VIDEO Initialize the video interface 4C TP_VID_SHADOW Copy the video BIOS to RAM 24 TP_SET_HUGE_ES Switch the ES ...

  • Siemens PC 670 - page 131

    Fault Diagnosis Release 04/02 6-1 1 Panel PC 670 Computing Unit, Equipment Manual Display (hex) Description Meaning 82 TP_RS232 Determine the serial interfaces 84 TP_LPT Determine the parallel interface 86 TP_IO_AFTER Re-enable the IO modules 83 TP_FDISK_CFG_IDE_CTRLR Configure the IDE controller 89 TP_ENABLE_NMI Enable the NMI 8C TP_FLOPPY Initial ...

  • Siemens PC 670 - page 132

    Fault Diagnosis Release 04/02 6-12 Panel PC 670 Computing Unit, Equipment Manual ...

  • Siemens PC 670 - page 133

    7-1 Panel PC 670 Computing Unit, Equipment Manual Hardware Information Chapter Overview In Section Y ou Will Find on Page 7.1 Current Requirement of the Components (Maximum V alues) 7-2 7.2 Overview of the Components and Ports 7-3 7.3 System Resources 7-5 7.4 Monitoring Functions 7-6 7.5 Interfaces 7-10 7.6 Wiring backplane 7-32 7.7 Power Supply Un ...

  • Siemens PC 670 - page 134

    Hardware Information Release 04/02 7-2 Panel PC 670 Computing Unit, Equipment Manual 7.1 Power Consumption of the Components (Maximum V alues) Basic system Component V oltage +5V +3.3V +12V – 5V – 12V Pentium III Motherboard 0.5 A 2.5 A 0.1 A 0.02 A Processor Pentium III 1260 5 A Floppy disk drive / LS 240 0.56 A Hard disk 0.4 A 0.5 A CD RW/DVD ...

  • Siemens PC 670 - page 135

    Hardware Information Release 04/02 7-3 Panel PC 670 Computing Unit, Equipment Manual 7.2 Overview of the Components and Interfaces Component/ Port Description Parameters Chipset VIA PN133T S SDRAM BIOS Update via software S 512K in 4 pages CPU Pentium III / Celeron (type FC-PGA370) S Upgradeable S Multimedia support S On Board L2-Cache with 128 k/2 ...

  • Siemens PC 670 - page 136

    Hardware Information Release 04/02 7-4 Panel PC 670 Computing Unit, Equipment Manual Component/ Port Parameters Description Parallel Standard, bidirectional, EPP and ECP modes S 25 pin subminiature Cannon connector DP12 Communication port SIMA TIC S7 S potentially isolated DP12 * 1 (CP 561 1 compatible) S 12MBaud USB Universal Serial Bus S three hi ...

  • Siemens PC 670 - page 137

    Hardware Information Release 04/02 7-5 Panel PC 670 Computing Unit, Equipment Manual 7.3 System Resources All system resources (Hardware adresses, Memory allocation, Interrupt allocation, DMA channels) are dinamically assigned by the Windows operating system depending on the specific hardware, drivers and connected external devices. Y ou can view t ...

  • Siemens PC 670 - page 138

    Hardware Information Release 04/02 7-6 Panel PC 670 Computing Unit, Equipment Manual 7.4 Monitoring Functions The LEDs described in the following sections are only available on specific versions of the device. The basic configuration of the computing unit does not have any LEDs. The hardware signals are described in Section 7.5.2. 7.4.1 Overview Fu ...

  • Siemens PC 670 - page 139

    Hardware Information Release 04/02 7-7 Panel PC 670 Computing Unit, Equipment Manual 7.4.3 T emperature monitoring/display T emperature monitoring The temperature is measured by means of three temperature sensors. One sensor monitors the processor temperature, the second the temperature in the area of the memory module and the expansion cards and t ...

  • Siemens PC 670 - page 140

    Hardware Information Release 04/02 7-8 Panel PC 670 Computing Unit, Equipment Manual 7.4.4 W atchdog (WD) Function The watchdog monitors the execution of a program. The purpose of the WD is to report a program crashing to the user by means of different reactions. After switching on the computing unit or after a HW-RESET (cold start) the watchdog re ...

  • Siemens PC 670 - page 141

    Hardware Information Release 04/02 7-9 Panel PC 670 Computing Unit, Equipment Manual 7.4.5 Fan monitoring The operation of the processor fan is monitored. If the fan should fail, the following reactions are triggered: Reaction Options T emp LED from GREEN to RED – Trigger IRQ Adjustable The error remains saved until the cause of the failed fan is ...

  • Siemens PC 670 - page 142

    Hardware Information Release 04/02 7-10 Panel PC 670 Computing Unit, Equipment Manual 7.5 Interfaces The following interfaces are available on the computing unit ’ s mainboard: S ports for connecting external devices S ports for connecting displays S ports for internal connections (drives, wiring backplane, etc.) The connector pin-outs of the dif ...

  • Siemens PC 670 - page 143

    Hardware Information Release 04/02 7-1 1 Panel PC 670 Computing Unit, Equipment Manual Serial interface COM1 (AG/V24/Modem) The serial interface (COM 1) of the computing unit is assigned as follows: 1 13 14 25 Figure 7-1 Serial interface COM1 (female) Pin No. Short Name Meaning Input/Output 1 - Shield - 2 TxD (D1) Serial transmission data Output 3 ...

  • Siemens PC 670 - page 144

    Hardware Information Release 04/02 7-12 Panel PC 670 Computing Unit, Equipment Manual Serial interface COM2 (V24/Mouse) The serial interface (COM2) of the computing unit is assigned as follows 1 5 6 9 Figure 7-2 Serial interface COM2 (male) Pin No. Short Name Meaning Input/Output 1 DCD (M5) Data carrier detect Input 2 RxD (D2) Received data Input 3 ...

  • Siemens PC 670 - page 145

    Hardware Information Release 04/02 7-13 Panel PC 670 Computing Unit, Equipment Manual Parallel interface LPT1 The parallel interface (LPT1) of the computing unit is assigned as follows: 1 13 14 25 Figure 7-3 Parallel interface LPT1 (female) Pin No. Short Name Meaning Input/Output 1 / Strobe (CLK) Data message Output (open collector) 2 Data bit 0 Da ...

  • Siemens PC 670 - page 146

    Hardware Information Release 04/02 7-14 Panel PC 670 Computing Unit, Equipment Manual PS/2 mouse interface It is possible to connect a PS/2 mouse to the computing unit. The port is assigned as follows: View of Socket 1 2 3 4 5 6 Figure 7-4 Connector Pinout for a PS/2 Mouse Pin No. Short Name Meaning Input/Output 1 DA T Mouse data line Input/Output ...

  • Siemens PC 670 - page 147

    Hardware Information Release 04/02 7-15 Panel PC 670 Computing Unit, Equipment Manual View of Socket 1 2 3 4 5 6 Figure 7-5 Connector Pinout for an External Keyboard Connecting Cable Pin No. Short Name Meaning Input/Output 1 DA T Keyboard data Input/Output 2 - Not assigned - 3 GND Chassis ground - 4 P5VFK +5V ( fused) Output 5 CLK Keyboard clock li ...

  • Siemens PC 670 - page 148

    Hardware Information Release 04/02 7-16 Panel PC 670 Computing Unit, Equipment Manual MPI/DP interface The MPI/DP port on the computing unit is assigned as follows: 1 5 6 9 Figure 7-7 PROFIBUS/MPI Socket Connector Pin No. Short Name Meaning Input/Output 1 - Not assigned - 2 - Not assigned - 3 L TG_B Signal lead B of MPI module Input/Output 4 R TS_A ...

  • Siemens PC 670 - page 149

    Hardware Information Release 04/02 7-17 Panel PC 670 Computing Unit, Equipment Manual Ethernet RJ45 connection The Ethernet-RJ45 interface of the computing unit is assigned as follows: LED green LED yellow 1 8 Figure 7-8 Ethernet port Pin No. Short Name Meaning Input/Output 1 TD+ T ransmission data Output 2 TD – T ransmission data Output 3 RD+ Re ...

  • Siemens PC 670 - page 150

    Hardware Information Release 04/02 7-18 Panel PC 670 Computing Unit, Equipment Manual VGA interface The VGA socket on the computing unit is assigned as follows: 1 5 6 10 11 15 Figure 7-9 VGA Socket Connector Pin No. Short Name Meaning Input/ Output 1 R red Output 2 G green Output 3 B Blue Output 4 - Not assigned - 5 GND Chassis ground - 6 GND Chass ...

  • Siemens PC 670 - page 151

    Hardware Information Release 04/02 7-19 Panel PC 670 Computing Unit, Equipment Manual 7.5.2 Interface allocation for connecting a front on the main board Interface Posi- tion Con- nector Description Display (CMOS) Internal X420 Connection of LC displays with CMOS port Display (L VDS) Internal X400 Connection of LC displays with single chip L VDS po ...

  • Siemens PC 670 - page 152

    Hardware Information Release 04/02 7-20 Panel PC 670 Computing Unit, Equipment Manual Pin Signal Meaning Pin Signal Meaning DSTN DSTN TFT TFT 1 P5V_D_fused +5V (fused) Display VCC 1 P5V_D_fused +5V (fused) Display VCC 2 P5V_D_fused +5V (fused) Display VCC 2 P5V_D_fused +5V (fused) Display VCC 3 GND 3 GND 4 CLK Shift clock 4 CLK Shift clock 5 GND 5 ...

  • Siemens PC 670 - page 153

    Hardware Information Release 04/02 7-21 Panel PC 670 Computing Unit, Equipment Manual Display port (L VDS), X400 TFT displays with an L VDS port can be connected to this port. 18-bit displays having a resolution up to 1024x768 pixels can be connected. The permissible display clock rate is 20 MHz to 66 MHz. The display is selected automatically acco ...

  • Siemens PC 670 - page 154

    Hardware Information Release 04/02 7-22 Panel PC 670 Computing Unit, Equipment Manual Assignment of display to display select pins Automatic configuration of one of 15 possible displays is performed by means of the Display Select inputs. The Display Select inputs have pull-up resistors – in other words, if these inputs are not connected, they go ...

  • Siemens PC 670 - page 155

    Hardware Information Release 04/02 7-23 Panel PC 670 Computing Unit, Equipment Manual I/O interface for front control elements All the signals necessary for the connection of front control elements, in addition to the display and USB ports, are applied to this port. The maximum cable length is 50 cm at a USB data rate of 12 Mbaud. Pin No. Short Nam ...

  • Siemens PC 670 - page 156

    Hardware Information Release 04/02 7-24 Panel PC 670 Computing Unit, Equipment Manual Internal serial interface COM2 (V .24), X26 This port is connected in parallel to the external COM2 port. Both ports can therefore only be used as alternately . They are assigned such that a 1:1 connection can be established to a 9-pin D-SUB socket when insulation ...

  • Siemens PC 670 - page 157

    Hardware Information Release 04/02 7-25 Panel PC 670 Computing Unit, Equipment Manual 2.5 ” hard disks Internal X4 170h-177h, 1F0h-1F7h, can be disabled IRQ14, IRQ15, edge-triggered 44 pin, 2mm male connector (2.5 ” HD, pri- mary), a maximum of two drives can be connec- ted CD-ROM drive Internal X3 170h-177h, 1F0h-1F7h, can be disabled IRQ14, I ...

  • Siemens PC 670 - page 158

    Hardware Information Release 04/02 7-26 Panel PC 670 Computing Unit, Equipment Manual DC interface of the power supply 105W The power supply unit has a connector (X2) through which all the signals on the DC side are connected with the motherboard. Pin No. Short Name Meaning 1 P5V +5V 2 P5V +5V 3 P5V +5V 4 P5V +5V 5 P5V +5V 6 PS_NAU_N Power failure, ...

  • Siemens PC 670 - page 159

    Hardware Information Release 04/02 7-27 Panel PC 670 Computing Unit, Equipment Manual Interface to floppy disk drive By means of this interface a notebook floppy disk drive may be connected. The maximum connection length of the data cable may not exceed 40cm. Pin No. Short Name Meaning Input/ Output 1 P5V +5V Output 2 INDEX_N Index hole recognition ...

  • Siemens PC 670 - page 160

    Hardware Information Release 04/02 7-28 Panel PC 670 Computing Unit, Equipment Manual Allocation of IDE intefaces The primary IDE port is designed for alternatively installing 2.5 ” and 3.5 ” hard disks. 3.5 ” drives are connected by means of a 40-pin 2.54 mm pitch connector and 2.5 ” drives by means of a 44-pin 2 mm pitch connector . The t ...

  • Siemens PC 670 - page 161

    Hardware Information Release 04/02 7-29 Panel PC 670 Computing Unit, Equipment Manual Pin No. X41 Meaning Pin No. X4/X3 Meaning 1 RESET Reset 1 RESET Reset 2 GND 2 GND 3 D7 Data signal D7 3 D7 Data signal D7 4 D8 Data signal D8 4 D8 Data signal D8 5 D6 Data signal D6 5 D6 Data signal D6 6 D9 Data signal D9 6 D9 Data signal D9 7 D5 Data signal D5 7 ...

  • Siemens PC 670 - page 162

    Hardware Information Release 04/02 7-30 Panel PC 670 Computing Unit, Equipment Manual Connection of an LS240 drive The optional LS240 drive is connected via this port. This port is connected in parallel to the secondary IDE port. The connected LS240 drive is automatically master (i.e. bootable drive) as the result of a special RC circuit. The maxim ...

  • Siemens PC 670 - page 163

    Hardware Information Release 04/02 7-31 Panel PC 670 Computing Unit, Equipment Manual SV connection for hard disk The power supply of the 3.5 ” hard disk is effected via this connection. Pin No. Short Name Description Input / Output 1 P12V +12 V Output 2 GND Chassis ground – 3 GND Chassis ground – 4 P5V +5 V Output Connection for CPU fan The ...

  • Siemens PC 670 - page 164

    Hardware Information Release 04/02 7-32 Panel PC 670 Computing Unit, Equipment Manual 7.6 Wiring Backplane 7.6.1 Design and Theory of Operation The bus board is designed as a passive link between the motherboard and the expansion modules. It is mounted with a screw . The bus board has two ISA slots and two PCI slots, as well as a shared ISA /PCI sl ...

  • Siemens PC 670 - page 165

    Hardware Information Release 04/02 7-33 Panel PC 670 Computing Unit, Equipment Manual Pin No. T ype Short Name Pin No. T ype* Short Name A12 SA 19 I/O B12 SMEMR# O A13 SA 18 I/O B13 IOW# I/O A14 SA 17 I/O B14 IOR# I/O A15 SA 16 I/O B15 DACK3# O A16 SA 15 I/O B16 DRQ 3 I A17 SA 14 I/O B17 – ACK1# O A18 SA 13 I/O B18 DRQ 1 I A19 SA 12 I/O B19 REFRE ...

  • Siemens PC 670 - page 166

    Hardware Information Release 04/02 7-34 Panel PC 670 Computing Unit, Equipment Manual Pin Signal Name T ype * Pin Signal Name T ype C1 – SBHE O D1 – MEMCS16 I C2 LA 23 I/O D2 – IOCS16 I C3 LA 22 I/O D3 IRQ 10 I C4 LA 21 I/O D4 IRQ 1 1 I C5 LA 20 I/O D5 IRQ 12 I C6 LA 19 I/O D6 IRQ 13 I C7 LA 18 I/O D7 IRQ 14 I C8 LA 17 I/O D8 – DACK0 O C9 ? ...

  • Siemens PC 670 - page 167

    Hardware Information Release 04/02 7-35 Panel PC 670 Computing Unit, Equipment Manual 5V System Environment Side B Side A 1 – 12V TRST# 2 TCK +12V 3 Ground TMS 4 TDO TDI 5 +5V +5V 6 +5V INT A# 7 INTB# INTC# 8 INTD# +5V 9 PRSNT1# Reserved 10 Reserved +5V (I/O ) 11 PRSNT2# Reserved 12 Ground Ground 13 Ground Ground 14 Reserved Reserved 15 Ground RS ...

  • Siemens PC 670 - page 168

    Hardware Information Release 04/02 7-36 Panel PC 670 Computing Unit, Equipment Manual Assignment of slot-specific PCI bus signals PCI Socket Pin No. PCI Slot 1 Shared ISA PCI Slot B16 clk (slot 1) clk (slot2) A6 inta# intb# A7 intc# intd# B7 intb# intc# B8 intd# inta# B18 req1 req0 A17 gnt1 gnt0 A26 ad29 ad30 ...

  • Siemens PC 670 - page 169

    Hardware Information Release 04/02 7-37 Panel PC 670 Computing Unit, Equipment Manual 7.7 Power supply (AC and DC) T echnical Data V oltage Max. current V oltage stability +12 V 2.5 A " 4% – 12 V 0.3 A " 5% + 5 V 13.5 A " 3% +3.3 V 8.5 A " 3% V oltage Input voltage 120/230V AC +15%/ – 20% 24V DC +20%/ – 15% Power consumpti ...

  • Siemens PC 670 - page 170

    Hardware Information Release 04/02 7-38 Panel PC 670 Computing Unit, Equipment Manual 7.8 Connecting cables SIMA TIC S5 Connecting Cable By means of the SIMA TIC S5 connecting cable (not included in all supply variants) you can connecto your computing unit with a SIMA TIC S5 automation device. Please study the notes in Chapter 3. Box PC 840 - Seite ...

  • Siemens PC 670 - page 171

    8-1 Panel PC 670 Computing Unit, Equipment Manual Distributed configuration Chapter Overview This chapter describes all specifications of the distributed configuration that are different from those of the integrated configuration (described in chapters 2 – 7). Where this manual focuses on the computing unit. Note The part of the description refer ...

  • Siemens PC 670 - page 172

    Distributed configuration Release 04/02 8-2 Panel PC 670 Computing Unit, Equipment Manual 8.1 Description 8.1.1 Overview Figure 8-1 shows a PC 670 computing unit (distributed configuration) with the transmitter fitted between mounting brackets. Transmitter housing Socket for connecting interconnecting cable Mounting brackets Mounting slot CDROM dri ...

  • Siemens PC 670 - page 173

    Distributed configuration Release 04/02 8-3 Panel PC 670 Computing Unit, Equipment Manual 8.1.2 Dimensions Figure 8-2 shows the dimensions of the PC 670 computing unit with transmitter . T ransmitter 21 1 253 289.6 74.3 25 104,1 8 304.6 297.2 43.5 Dimensions in m m Figure 8-2 Dimensions computing unit PC 670 without CD-ROM drive in distributed conf ...

  • Siemens PC 670 - page 174

    Distributed configuration Release 04/02 8-4 Panel PC 670 Computing Unit, Equipment Manual 8.2 Cable connection T ransmitter and receiver are connected by a cable with a maximum length of 20 m. For operation, the angled cable connector is inserted in the socket of the transmitter and locked. The interconnecting cable must also be fixed in position. ...

  • Siemens PC 670 - page 175

    Distributed configuration Release 04/02 8-5 Panel PC 670 Computing Unit, Equipment Manual T ransmitter Port for interconnecting cable Encoder S30 Computing unit T ransmitter housing Center screwhole Groove for outer fastening screws Figure 8-3 T ransmitter in opened transmitter housing 4. Check (or set) the switch setting as shown in the table belo ...

  • Siemens PC 670 - page 176

    Distributed configuration Release 04/02 8-6 Panel PC 670 Computing Unit, Equipment Manual ...

  • Siemens PC 670 - page 177

    A-1 Panel PC 670 Computing Unit, Equipment Manual T echnical Data In this Appendix This appendix contains the following technical specifications for the Panel PC 670 computing unit: S General Information S Safety S Electromagnetic Compatibility (EMC) S Ambient Conditions S Mechanical environmental conditions S Motherboard S Drives S Graphics card S ...

  • Siemens PC 670 - page 178

    T echnical Data Release 04/02 A-2 Panel PC 670 Computing Unit, Equipment Manual A.1 T echnical Data of the Panel PC 670 Computing Unit General Order nos. See order documentation Dimensions 297x267x80 (WxHxD in mm), without CD-ROM drive 297x267x101 (WxHxD in mm), with CD-ROM drive W eight approx. 6kg (13.5 lbs.) Supply voltage (U N ) 120 V (85 V to ...

  • Siemens PC 670 - page 179

    T echnical Data Release 04/02 A-3 Panel PC 670 Computing Unit, Equipment Manual Environmental conditions T emperature – operation – storage/transport – gradient tested to DIN EN 60068-2-2:1994, DIN IEC 60068-2-1, DIN IEC 60068-2-14, +5 ° C to +45 ° C - 20 ° C to +60 ° C max 10 ° C/h (no condensation) Relative humidity – operation – s ...

  • Siemens PC 670 - page 180

    T echnical Data Release 04/02 A-4 Panel PC 670 Computing Unit, Equipment Manual Graphic Graphic controller UXGA LCD controller on the AGP bus Graphic store bis zu 32 MB SDRAM sind Bestandteil des Hauptspeichers und k ö nnen konfiguriert werden (8/16/32MB) Resolutions/frequencies/colors CR T : up to 1600x1200/85 Hz / 65536 colors with PC133 up to 1 ...

  • Siemens PC 670 - page 181

    B-1 Panel PC 670 Computing Unit, Equipment Manual ESD Guidelines Chapter Overview In chapter Y ou Will Find on Page B.1 What does ESD mean? B-2 B.2 Electrostatic charge of people B-3 B.3 Basic safety measures against discharge of static electricity B-4 B ...

  • Siemens PC 670 - page 182

    ESD Guidelines Release 04/02 B-2 Panel PC 670 Computing Unit, Equipment Manual B.1 What does ESD mean? Definition All electronic components are equipped with high- int egrat ed modules or component s. Conditioned by their technology, thes e electronic component s are extr emely sensitiv e to overv oltages and therefore to discharges of st atic elec ...

  • Siemens PC 670 - page 183

    ESD Guidelines Release 04/02 B-3 Panel PC 670 Computing Unit, Equipment Manual B.2 Electrostatic Charge of People Charging Anyone who is not conduc tively connect ed to the electrical potential of their surroundings can be electrost at ically charged. The maximum electrostatic voltage values which an operator can be charged with when contacting the ...

  • Siemens PC 670 - page 184

    ESD Guidelines Release 04/02 B-4 Panel PC 670 Computing Unit, Equipment Manual B.3 Basic Safety Measures against Discharge of Static Electricity Ensuring a good ground connection When handling electr ostat ic sensitiv e devices, ensure that your person, the workplace and packaging are grounded. In this manner you avoid static charge. A void direct ...

  • Siemens PC 670 - page 185

    C-1 Panel PC 670 Computing Unit, Equipment Manual SIMA TIC HMI Documentation T arget groups This manual is part of the SIMA TIC HMI documentation. The documentation is aimed at the following target groups: S Newcomers S Users S Configurers S Programmers S Commissioning engineers Structure of the documentation The SIMA TIC HMI documentation consists ...

  • Siemens PC 670 - page 186

    SIMA TIC HMI Documentation Release 04/02 C-2 Panel PC 670 Computing Unit, Equipment Manual Documentation T arget Group Content First Steps with ProT ool Product Brief Newcomers This documentation guides you step by step through the configuration of S a screen with various objects S a change of display and S a message. This documentation is availabl ...

  • Siemens PC 670 - page 187

    SIMA TIC HMI Documentation Release 04/02 C-3 Panel PC 670 Computing Unit, Equipment Manual Content T arget Group Documentation Copy Protection Start-up Guide Commissioning engineers, Users The ProT ool/Pro Runtime visualization software is a copyright product. This manual contains information on the installation, repair and uninstallation of author ...

  • Siemens PC 670 - page 188

    SIMA TIC HMI Documentation Release 04/02 C-4 Panel PC 670 Computing Unit, Equipment Manual Content T arget Group Documentation Communication User ’ s Guide Programmers Contains information on connecting line- and graphic-based control panels to the following controls: S SIMA TIC S5 S SIMA TIC S7 S SIMA TIC 500/505 S drivers for other PLCs This do ...

  • Siemens PC 670 - page 189

    Glossary-1 Panel PC 670 Computing Unit, Equipment Manual Glossary A APM Advanced Power Management. Application An application is a program directly linked to the MS-DOS or Windows operating system. Applications on SIMA TIC PCs are, for example, the visualization packages SIMA TIC ProT ool/Pro, SIMA TIC WinCC and others. Automation system (AS) A con ...

  • Siemens PC 670 - page 190

    Glossary Release 04/02 Glossary-2 Panel PC 670 Computing Unit, Equipment Manual Configuration software Configuration software updates the device configuration when modules are fitted. This is done either by copying the configuration files supplied with the device of by manual configuration. D Device configuration The device configuration of a SIMA ...

  • Siemens PC 670 - page 191

    Glossary Release 04/02 Glossary-3 Panel PC 670 Computing Unit, Equipment Manual Interrupt Discontinuation in the processor of a programmable controller by an interrupt event. IRQ Interrupt request. ISA Industrial Standard Architecture (bus for expansion board) K Keyboard port PS/2 keyboard connector Keyboards with an integrated trackball can be con ...

  • Siemens PC 670 - page 192

    Glossary Release 04/02 Glossary-4 Panel PC 670 Computing Unit, Equipment Manual MPI/DP port (Multi-Point-Interface/Profibus-DP) for connecting an S7 programmable controller . P Parallel port Information is transferred on a byte by byte basis through a parallel port. High data transfer rates are achieved as a result. SIMA TIC PCs have one parallel p ...

  • Siemens PC 670 - page 193

    Glossary Release 04/02 Glossary-5 Panel PC 670 Computing Unit, Equipment Manual S SCSI interface Small Computer System Interface. Interface for connecting SCSI devices (for example, hard disks, CD-ROM drives) SETUP (BIOS Setup) A program which defines information about the device configuration. The device configuration of the SIMA TIC PC is preset. ...

  • Siemens PC 670 - page 194

    Glossary Release 04/02 Glossary-6 Panel PC 670 Computing Unit, Equipment Manual ...

  • Siemens PC 670 - page 195

    Index-1 Panel PC 670 Computing Unit, Equipment Manual Index A Acclimatization, 1-4 APM (Advanced Power Management), 5-24 A T modules, 4-12 B Backup battery , 3-17 replacement, 4-10 Batteries, 1-7 disposal, 1-7 Battery , 3-17 safety notes, 3-17 Beep Codes, 6-8 BIOS, error messages, 6-6 BIOS Setup, 5-1 call, 5-2 Configure APM, 5-24 Configure COM/LPT ...

  • Siemens PC 670 - page 196

    Index Release 04/02 Index-2 Panel PC 670 Computing Unit, Equipment Manual Computing unit permissible installation positions, 2-5 , 2-6 printer connection, 3-6 , 3-7 Protection class, A-2 PS/2 keyboard connection, 3-8 PS/2 mouse connection, 3-7 rating plate, 3-5 Reset button, 4-27 Reset button, 3-5 serial mouse connection, 3-8 starting up, 2-1 switc ...

  • Siemens PC 670 - page 197

    Index Release 04/02 Index-3 Panel PC 670 Computing Unit, Equipment Manual Front interfaces, 3-5 G Graphic, technical data, A-4 Green PC, 5-24 H Hard disk, 3-16 Hard disk drive, 3-16 removing and installing, 4-17 Hardware Information, 7-1 Connecting cables, 7-38 Interfaces and parameters, 7-3 Monitoring functions, 7-6 Power consumption of the system ...

  • Siemens PC 670 - page 198

    Index Release 04/02 Index-4 Panel PC 670 Computing Unit, Equipment Manual Module retainer plates, removing and installing, 4-14 Monitor , 3-4 Monitoring functions, 7-6 Fan monitoring, 7-9 Signals on the front interface, 7-6 SOM (Safecard On Motherboard), 7-6 T emperature monitoring, 7-7 W atchdog, 7-8 W atchdog-monitoring times, 7-8 Motherboard, 4- ...

  • Siemens PC 670 - page 199

    Index Release 04/02 Index-5 Panel PC 670 Computing Unit, Equipment Manual T T arget groups, C-1 T echnical data Computing unit, A-2 distributed configuration, 8-4 Graphic, A-4 Interfaces, A-4 T ime, setting up, 5-6 T ools, 4-3 T ransmitter, distributed configuration, 8-4 T ransport, 2-9 TTY - interface, 3-19 U USB Interface, 7-15 USB devices, conne ...

  • Siemens PC 670 - page 200

    Index Release 04/02 Index-6 Panel PC 670 Computing Unit, Equipment Manual ...

Manufacturer Siemens Category Personal Computer

Documents that we receive from a manufacturer of a Siemens PC 670 can be divided into several groups. They are, among others:
- Siemens technical drawings
- PC 670 manuals
- Siemens product data sheets
- information booklets
- or energy labels Siemens PC 670
All of them are important, but the most important information from the point of view of use of the device are in the user manual Siemens PC 670.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Siemens PC 670, service manual, brief instructions and user manuals Siemens PC 670. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Siemens PC 670.

Similar manuals

A complete manual for the device Siemens PC 670, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Siemens PC 670 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Siemens PC 670.

A complete Siemens manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Siemens PC 670 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Siemens PC 670, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Siemens PC 670, that we can find in the current document
3. Tips how to use the basic functions of the device Siemens PC 670 - which should help us in our first steps of using Siemens PC 670
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Siemens PC 670
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Siemens PC 670 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Siemens PC 670?

Use the form below

If you did not solve your problem by using a manual Siemens PC 670, ask a question using the form below. If a user had a similar problem with Siemens PC 670 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)