English dropdown-ico

Manual Echo BRD-280

36 pages 1.62 mb
Download

Go to site of 36

Summary
  • Echo BRD-280 - page 1

    w arning Read rules for safe operation and instructions carefully . ECHO provides an Opera- tor's Manual and a Safety Manual. Both must be read and understood for proper and safe operation. Bed Redener Operator's Manual MODEL BRD-280 X750012083 01/1 1 X750231 1203 ...

  • Echo BRD-280 - page 2

    2 Copyright© 201 1 By Echo, Incorporated All Rights Reserved. I n t r o d u c t I o n W elcome to the ECHO family . This ECHO product was designed and manufactured to provide long life and on-the-job- dependability . Read and understand this manual and the SAFETY MANUAL you found in the same package. Y ou will nd both easy to use and full of he ...

  • Echo BRD-280 - page 3

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 3 s a f e t y m a n u a l s a f e t y s y m b o l s a n d I m p o r t a n t I n f o r m a t I o n Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages pre - ceded by symbols or key words. The following is an explanation of thos ...

  • Echo BRD-280 - page 4

    4 Physical Condition Y our judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection W ear eye protection that meets ANSI Z87.1 or CE require- ments whenever you operate the unit. H ...

  • Echo BRD-280 - page 5

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 5 w arning Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the Manuals • Provide all users of this equipment with the Operator’ s Manual and Safety Manual for instructions ...

  • Echo BRD-280 - page 6

    6 An Emission Control Label is located on the engine. (This is an EXAMPLE ONL Y , information on label varies by engine F AMIL Y). e q u I p m e n t w arning Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combi- nation. ECHO, INC. will not be responsible for the failure of cutting devices, at ...

  • Echo BRD-280 - page 7

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 7 1 4 5 6 7 8 9 2 3 Shaft Decal d e s c r I p t I o n Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer . See P AR TS ORDERING i ...

  • Echo BRD-280 - page 8

    8 1. POWER HEAD - Factory assembled. Includes the engine, clutch, fuel system, ignition system and starter . 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 3. STOP SWITCH - "Slide Switch" mounted on top of the throttle ...

  • Echo BRD-280 - page 9

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 9 a s s e m b l y Parts Requir ed: Power head, Drive Shaft Assembly d r I v e s h a f t / p o w e r h e a d 1. Stand power head upright on a level surface. 2. Loosen the two (2) drive shaft clamp bolts (B) at engine drive shaft clamp, and remove center drive shaft location bolt (A). 3. Re ...

  • Echo BRD-280 - page 10

    10 5. T ighten two (2) drive shaft clamp bolts (B) securely . a B B a B C D C D t h r o t t l e l I n k a g e a n d I g n I t I o n l e a d s 1. Close choke and remove air lter cover . 2. Place inner throttle cable in large hole of carburetor swivel (A). 3. Loosen nuts (B) and place threaded end of throttle linkage in bracket slot. Finger tighte ...

  • Echo BRD-280 - page 11

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 11 s u p p o r t h a n d l e Parts Requir ed: Support Handle, Lower Bracket, 4 - 5 x 35 mm screws NOTE Label shows minimum spacing for front handle location. 1. Assemble front handle and bracket loosely to drive shaft. 2. Position front handle in comfortable operating position and tighten ...

  • Echo BRD-280 - page 12

    12 f u e l NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual. w arning Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels ...

  • Echo BRD-280 - page 13

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 13 IMPOR T ANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel sta- bilizer is added. IMPOR T ANT Stored two-stroke fuel may separate. AL W A YS shake fuel container thor - oughly before each use. Handling Fuel w arning Fuel ...

  • Echo BRD-280 - page 14

    14 s t a r t I n g c o l d e n g I n e w arning The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury . Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown. 1. Stop Switch Move stop switch (A) away from the STOP posit ...

  • Echo BRD-280 - page 15

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 15 s t a r t I n g w a r m e n g I n e The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. w arning The attachment should not move at idle, otherwise serious personal injury may result. NOTE If attachme ...

  • Echo BRD-280 - page 16

    16 NOTE For best results, use BRD redening blade (provided with unit) ONL Y for redening existing bed edges. For edging next to curbs, sidewalks, or other hard surfaces, remove redening blade and install ECHO Approved Premium Power Edger blade. Use of redening blade next to hard surfaces, can lead to premature blade wear . 1. Always gri ...

  • Echo BRD-280 - page 17

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 17 8. If shield clogs with mud or debris, do not hit unit against hard surfaces to clean, or damage to unit may occur . Stop engine and unclog shield with a suitable tool. IMPOR T ANT Be sure blade has completely stopped spinning before setting unit on concrete or other hard surface. Neve ...

  • Echo BRD-280 - page 18

    18 NOTE Blade depth may have to be adjusted due to differences in height between the hard surface and the top of the grass. 4. Loosen blade adjustment knob and adjust the blade’ s depth of cut to produce a ne cut between sidewalk and grass using a minimum blade depth, usually with about 13 mm (1/2 in.) of the blade into the ground. T ighten ad ...

  • Echo BRD-280 - page 19

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 19 m a I n t e n a n c e I n t e r v a l s COMPONENT / SYSTEM MAINTENANCE PROCEDURE REQ'D SKILL LEVEL DAILY OR BEFORE USE EVERY REFUEL 3 MONTHS OR 90 HOURS YEARLY 600 HOURS Air Filter Inspect/Clean 1 I / C * R* Choke Inspect/Clean 1 I / C Fuel Filter Inspect 1 I * I / R * Fuel Cap Ga ...

  • Echo BRD-280 - page 20

    20 a I r f I l t e r Level 1. Parts r equired: REPOWER TM AIR & FUEL FIL TER KIT . 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air lter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air lter cover . Brush dirt from inside cover . 3. Remove air lter and ...

  • Echo BRD-280 - page 21

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 21 s p a r k p l u g Level 2. Parts Requir ed: REPOWER TM T une-Up Kit IMPOR T ANT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) other - wise severe engine damage may occur . 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace w ...

  • Echo BRD-280 - page 22

    22 e x h a u s t s y s t e m Spark Arrestor Screen Level 2. Parts Requir ed: Spark Arrestor Screen, Gasket 1. Remove two (2) mufer cover screws and mufer cover (A). 2. Place piston at T op Dead Center (TDC) to prevent carbon/dirt from entering cylinder . 3. Remove spark arrestor screen (B), gasket (C) and exhaust guide (D) from mufer body ...

  • Echo BRD-280 - page 23

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 23 Exhaust Port Cleaning Level 2. Parts Requir ed: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove mufer cover (2 screws). 2. Place piston at top dead center . Remove mufer (A) and heat shield (B). 3. Use a wood or plastic scraping tool to clean deposits ...

  • Echo BRD-280 - page 24

    24 Level 2. Parts r equired: None NOTE Every unit is run at the factory and the carburetor is set in compli- ance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer . 1. Check idle speed and reset if necessary . If a tachometer is avail- able, idle speed screw (A) should be set t ...

  • Echo BRD-280 - page 25

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 25 b l a d e r e p l a c e m e n t / l u b r I c a t I o n Level 1. Parts Requir ed: POWER BLENDX TM 8 oz. (P/N 91014) or Lithium Base Grease, Blade P/N 99944208000, split pin P/N 90030020022 NOTE Grease gear case every 15 - 25 hours of use. Replace blade when carbide tips have worn away ...

  • Echo BRD-280 - page 26

    26 8. Install inner blade adapter (B) onto PTO shaft (C). 9. Install and center new blade (F) onto inner xing plate (B), with longest side toward shield. 10. Install outer xing plate (E) and nut (D). Tighten nut (D) rmly , counterclockwise (CCW). IMPOR T ANT Never reuse old split pin. 1 1. Install new split pin (A) to secure nut. ...

  • Echo BRD-280 - page 27

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 27 DangEr Fuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result. T r a H C g n i T O O H S E L B U O r T M E L B O r P E n i g n E m e l b o r ...

  • Echo BRD-280 - page 28

    28 s t o r a g e w arning During operation the mufer or catalytic mufer and surrounding cover become hot. Always keep exhaust area clear of ammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long T erm Storage (over 30 days) Do not store your unit for a prolonged period of ...

  • Echo BRD-280 - page 29

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 29 s p e c I f I c a t I o n s MODEL ---------------------------------------------------- BRD-280 Length ------------------------------------------------------- 1791 mm (70.51 in.) W idth -------------------------------------------------------- 280 mm (1 1.02 in.) Height ----------------- ...

  • Echo BRD-280 - page 30

    30 w a r r a n t y s t a t e m e n t s ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limi ted Warranty , provides to the original purchaser that this ECHO product is free from defects in material an d workmanship . Under normal use and maintenance from dat ...

  • Echo BRD-280 - page 31

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 31 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES  ? ...

  • Echo BRD-280 - page 32

    32 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIW A BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equi ...

  • Echo BRD-280 - page 33

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 33 n o t e s ...

  • Echo BRD-280 - page 34

    34 n o t e s ...

  • Echo BRD-280 - page 35

    B e d R e d e f i n e R O p e R a t O R ' s M a n u a l 35 n o t e s ...

  • Echo BRD-280 - page 36

    CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T . ECHO, INCORPORA TED 400 O a k w O O d R O a d L a k e Z u R i c h , iL 60047 www .echo-usa.com DEaLEr? Call 1-800-432-ECHO 1-800-432-3246 or www .echo-usa.com S7071 1001001/S70711 002517 S70812001001/S70812 014074 s e r v I c I n g I n f o r m a t I o n p a r t s / s e r I a l n ...

Manufacturer Echo Category Universal Remote

Documents that we receive from a manufacturer of a Echo BRD-280 can be divided into several groups. They are, among others:
- Echo technical drawings
- BRD-280 manuals
- Echo product data sheets
- information booklets
- or energy labels Echo BRD-280
All of them are important, but the most important information from the point of view of use of the device are in the user manual Echo BRD-280.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Echo BRD-280, service manual, brief instructions and user manuals Echo BRD-280. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Echo BRD-280.

Similar manuals

A complete manual for the device Echo BRD-280, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Echo BRD-280 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Echo BRD-280.

A complete Echo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Echo BRD-280 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Echo BRD-280, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Echo BRD-280, that we can find in the current document
3. Tips how to use the basic functions of the device Echo BRD-280 - which should help us in our first steps of using Echo BRD-280
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Echo BRD-280
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Echo BRD-280 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Echo BRD-280?

Use the form below

If you did not solve your problem by using a manual Echo BRD-280, ask a question using the form below. If a user had a similar problem with Echo BRD-280 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)