-
Electro-Voice Sx600 - page 1
Electro-V oice ® Sx600 User Manual ...
-
Electro-Voice Sx600 - page 2
Electro-V oice ® T able of Contents Product Description ................................................................................. 1 Important Features .................................................................................. 1 Product Feature Identification .................................................................. 2 Syste ...
-
Electro-Voice Sx600 - page 3
Electro-V oice ® Product Description The Sx600 Series is a remarkably flexible indoor/outdoor speaker system designed to produce high-fidelity high-level audio in distributed applications such as stadiums, ra cetracks, amusement parks, fairgrounds, etc. Utilizing a 65° x 65° high frequency horn and a unique 2-element vertical midbass array , Sx6 ...
-
Electro-Voice Sx600 - page 4
Electro-V oice ® Product Feature Identification Figure 1: Sx600 Product Features S tainless S teel SuperSAM TM Mounting Bracket SuperSAM TM Down Angle Adjustment (0°- 60° in 5° Increments) Full Face S tainless S teel Grille with Hydrophobic Backing (Not Shown) All S tainless S teel Hardware (Not Shown) Enclosure (Front View) Enclosure ( ...
-
Electro-Voice Sx600 - page 5
Electro-V oice ® System Acoustic Design Considerations Direct radiator acoustic systems can offer great vocal band clarity but dont usually of fer the ef ficiency and directivity of horn loaded systems. Horn loaded systems , if the overall dimensions are large enough, can of fer great directivity control, but typical multi-way horn designs, par ...
-
Electro-Voice Sx600 - page 6
Electro-V oice ® Installation Precautions This document det ails general mounting practices appropriate to the entertainment industry , as they would apply to the mounting of Electro- V oice Sx600 loudspeaker systems. It is intended to familiarize the reader with mounting hardware and techniques for suspending Sx600 loud- speaker systems overhead. ...
-
Electro-Voice Sx600 - page 7
Electro-V oice ® 5 Block W all Mounting Do not attempt to mount an Sx600 to a block or brick wall without through-bolts and large, heavy steel backing plates on both sides of the wall. On poured concrete walls use deep ½ inch diameter anchors that cannot be pulled out once set. Use all 6 mounting holes. SuperSAM TM Bracket 1/2 Bolts (6 Reqd ...
-
Electro-Voice Sx600 - page 8
Electro-V oice ® Stud W all Mounting First determine whether the structural members in the wall can withstand not only the weight of the Sx600, but also the side-to-side stresses of heavy cross-winds. Reinforce both sides of the wall with heavy plates, ¾ inch marine plywood minimum, and use through bolts. Never rely on lag bolts alone. Additional ...
-
Electro-Voice Sx600 - page 9
Electro-V oice ® Installation Procedure S tep 1: Selection and Preparation of the Mounting Surface Surface must be clean and smooth. It must also be a material that is not easily crushed. While the SuperSAM TM distributes weight evenly over a relatively large area, strong winds against the side of the Sx600 will exert significant crowbar-like leve ...
-
Electro-Voice Sx600 - page 10
Electro-V oice ® S tep 4: Completing the Electrical Connections T rim the SJO cord to a neat length while allowing enough slack for future aiming adjustment s or service. Make electrical connections per all applicable codes in a weather-tight box and secure the SJO cord through a weather-tight gland nut. Observe color code for proper polarity: Bla ...
-
Electro-Voice Sx600 - page 11
Electro-V oice ® Selecting W att age T a p s The Sx600 is intended to be a high level speaker , so the transformer taps are set up to produce a full 600 watts at each of the 4 voltages listed. If necessary , the wattage may be halved by selecting the next HIGHER volt age tap. NEVER select a tap for a LOWER voltage! (i.e; Do not use a 70 volt tap i ...
-
Electro-Voice Sx600 - page 12
Electro-V oice ® S tep 5: System Adjustment and Acoustic Tuning The Sx600 MUST BE HI-P ASSED at 90Hz using a minimum slope of 12dB/octave with a Q of 1.6. (Easily obtainable on the Electro-V oice Dx- 38 Digit al Loudspeaker Controller) If analog filtering is used, a 70Hz high-pass filter of at least 12dB/octave slope and low frequency EQ of NO MOR ...
-
Electro-Voice Sx600 - page 13
Electro-V oice ® 11 System shut s down when driven hard. 1.) Insufficient amplifier power . Amplifier goes into protect mode due to overcurrent or thermal stress. Switch to a larger amplifier . 2.) Line impedance too low . (PI models in p articular) Some amplifiers will not drive a 2 ohm load at full power , especially if both channels are loaded ...
-
Electro-Voice Sx600 - page 14
Electro-V oice ® 12 the microphone and use a good compressor/limiter to compensate for variances in microphone distance and excitement. Appendix B: Warranty S tatement Electro-V oice® product s are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as noted in the individual product-line st atement(s ...
-
Electro-Voice Sx600 - page 15
Electro-V oice ® 13 not apply to burned voice coils or malfunctions such as cone and/or coil damage resulting from improperly designed enclosures. Electro-V oice® active electronics associated with the speaker systems are guaranteed for three (3) years from the date of original purchase. Additional details are included in the Uniform Limited W ar ...
-
Electro-Voice Sx600 - page 16
Electro-V oice ® U.S.A. and Canada: For customer orders, contact the Customer Service department at: 800/392-3497 Fax: 800/955-6831 For warranty repair or service information, contact the Service Repair Department at: 800/685-2606 For technical assistance, contact T echnical Support at: 866/78-AUDIO S pecifications subject to change without notice ...
Do you have a question concerning Electro-Voice Sx600?
Use the form below
If you did not solve your problem by using a manual Electro-Voice Sx600, ask a question using the form below. If a user had a similar problem with Electro-Voice Sx600 it is likely that he will want to share the way to solve it.