English dropdown-ico

Manual Bissell BS-9400F

24 pages 0.1 mb
Download

Go to site of 24

Summary
  • Bissell BS-9400F - page 1

    Troubleshooting Bissell ProHeat 2X Select BS-9400F CONTENTS PAGE Consumer states unit will not spray to the floor and no spray from the upholstery tool…………………………………………………….Page 2 Consumer states no or low suction…………………….…………………..Page 8 Consumer states unit will spray through the ...

  • Bissell BS-9400F - page 2

    Prepared by Monique Lania 2 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states unit will not spray to the floor and no spray from the upholstery tool Solution 1: Solution 1: The Red float door inside lid of 2-in-1 Tank may have closed as a result of the Tank being full of dirty water and needs to be emptied and refilled with clean water, or ...

  • Bissell BS-9400F - page 3

    Prepared by Monique Lania 3 Call Servicing Guide ProHeat 2X 9400F.doc Solution 2: Has Tank-in-tank been emptied and refilled and has the SmartMix (solution) bottle bee n filled with solution? No, empty and refill water tank and fill SmartMix bottle (solution bottle) with Bissell Solution, problem solved Yes Tank-in-Tank may not be seated in machine ...

  • Bissell BS-9400F - page 4

    Prepared by Monique Lania 4 Call Servicing Guide ProHeat 2X 9400F.doc Solution 3: Solution 2: Yes Yes Remove SmartMix bottle from unit Advise customer to call Bissell Free Call 1800 number again and press Option 4 for spare parts and order replacement SmartMix bottle Yes, reattach gasket by pushing the red rounded portion over the lip of the bottom ...

  • Bissell BS-9400F - page 5

    Prepared by Monique Lania 5 Call Servicing Guide ProHeat 2X 9400F.doc Solution 4: How? Using a Phillips Head Screw Driver, unscrew the scr ew just above the front nozzle and remove it. Turn the machine on its side so that the belt access area is facing upwards. Making sure the cord side of the machine is facing down Remove the clear end cap by unsc ...

  • Bissell BS-9400F - page 6

    Prepared by Monique Lania 6 Call Servicing Guide ProHeat 2X 9400F.doc Locate the Small Brush Belt, has it come off the Brush end? Yes, refit by reversing the steps above. If the small Brush Belt is damaged or broken advise customer to call Bissell Free Call 1800 number again and press Option 4 for spare parts and order replacement small Brush Belt ...

  • Bissell BS-9400F - page 7

    Prepared by Monique Lania 7 Call Servicing Guide ProHeat 2X 9400F.doc Solution 5: How? Using a Phillips Head Screw Driver, unscrew the scr ew just above the front nozzle and remove it. Turn the machine on its side so that the belt access area is facing upwards. Making sure the cord side of the machine is facing upwards. Remove the clear end cap by ...

  • Bissell BS-9400F - page 8

    Prepared by Monique Lania 8 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states no or low suction Solution 1: Ensure Diverter Knob located on Tank is switched to the correct setting ‘Hose Attachments if you are using the upholstery hose or ‘Floor Cleaning’ if you are cleaning the floor. Is there suction now? The Red float door inside li ...

  • Bissell BS-9400F - page 9

    Prepared by Monique Lania 9 Call Servicing Guide ProHeat 2X 9400F.doc Solution 2: Grab handle on Tank and lift/pull towards you to remove tank-in-tank assembly from unit. Is the lid or tank damaged? No Ensure Tank Lid is securely attached to tank as this is where all the suction is and it depends on it being air tight Yes, problem solved How do you ...

  • Bissell BS-9400F - page 10

    Prepared by Monique Lania 10 Call Servicing Guide ProHeat 2X 9400F.doc Solution 3: Remove the tank-in-tank assembly from the unit How? Remove Tank Lid from Tank Pull and lift grey latch on back of Tank to unlatch and remove tank lid. How? Using your finger tips, remove any debris from the red Lint Filter Basket and rinse red Lint Filter in hot tap ...

  • Bissell BS-9400F - page 11

    Prepared by Monique Lania 11 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states unit will spray through the hose , but not to the floor. Solution 1: Solution 2: Remove any debris on the spray tips located at bottom of unit with a soft brush (an old toothbrush works well). Turn unit on. Does unit spray now? Yes, problem solved Turn unit off N ...

  • Bissell BS-9400F - page 12

    Prepared by Monique Lania 12 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states unit will spray at the floor , but not through the upholstery hose. Solution 1: Remove any tools from the end of the upholstery hose. Does the unit spray through the hose now? No Clean out the spray tip with the end of an unfolded paper clip. Does the unit spray ...

  • Bissell BS-9400F - page 13

    Prepared by Monique Lania 13 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states unit is releasing too much solution or only shampoo. Solution 1: Yes No Is the black O shaped ring on the SmartMix Cap Insert fitted securely over the cap insert & straw? ** NOTE: Some O rings are detachable and need to fit over the straw; others are molded t ...

  • Bissell BS-9400F - page 14

    Prepared by Monique Lania 14 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states unit will not release any shampoo Solution 1: No Remedy Yes Does the SmartMix Knob (located next to Sm artMix solution bottle) function properly? Is there liquid in the SmartMix reservoir (where the SmartMix bottle sits in the unit)? Is the red O shaped ring on t ...

  • Bissell BS-9400F - page 15

    Prepared by Monique Lania 15 Call Servicing Guide ProHeat 2X 9400F.doc Solution 2: Turn the unit on Yes, problem solved Yes No Reattach gasket by pushing the red rounded portion over the black lip of the SmartMix bottle or order new gasket if appropriate, problem solved Fill the Tank- in-Tank Assembly with hot (not boiling) water and place in unit ...

  • Bissell BS-9400F - page 16

    Prepared by Monique Lania 16 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states no suction through the upholstery hose but does have suction at the floor. Solution 1: Yes, problem solved No, Flick it backwards towards you from ‘Brush’ setting to ‘Suction’ setting. Is there suction now? On the Turbo brush attachment, is the black slid ...

  • Bissell BS-9400F - page 17

    Prepared by Monique Lania 17 Call Servicing Guide ProHeat 2X 9400F.doc Consumer reports the wat e r that is spray ed out is not hot . Solution 1: Is the machine switched on at the power outlet in the wall? Allow heater to warm up for about 2 minutes. Is the water spraying out hot now? Yes, is the power switch and red heater switch on the unit switc ...

  • Bissell BS-9400F - page 18

    Prepared by Monique Lania 18 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states the brush will not turn . **NOTE: When the machine is in an upright position, the brushes will automatically stop turning to avoid an y damage to the floor. The brushes will only rotate when the unit is reclined using the detent pedal **NOTE: Advise customer that ...

  • Bissell BS-9400F - page 19

    Prepared by Monique Lania 19 Call Servicing Guide ProHeat 2X 9400F.doc Solution 2: How? Using a Phillips Head Screw Driver, unscrew the scr ew just above the front nozzle and remove it. Turn the machine on its side so that the belt access area is facing upwards. Making sure the cord side of the machine is facing down Remove the clear end cap by uns ...

  • Bissell BS-9400F - page 20

    Prepared by Monique Lania 20 Call Servicing Guide ProHeat 2X 9400F.doc Solution 3: How? Using a Phillips Head Screw Driver, unscrew the scr ew just above the front nozzle and remove it. Turn the machine on its side so that the belt access area is facing upwards. Making sure the cord side of the machine is facing upwards. Remove the clear end cap by ...

  • Bissell BS-9400F - page 21

    Prepared by Monique Lania 21 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states the unit has no power . Solution 1 How? Slide upper handle firmly onto lower handle unt il screw holes are completely aligned Align upper handle screw holes and top half of t ool caddy holes Yes, problem solved In order for the unit to operate the upper handle mu ...

  • Bissell BS-9400F - page 22

    Prepared by Monique Lania 22 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states the unit drags on carpet Solution 1: With a Phillips head screw driver ensure the screw in the middle just above the front nozzle is tight. Does the machine drag now? No, problem solved Yes, Is the plastic around the screw cracked? No, refer customer to an Author ...

  • Bissell BS-9400F - page 23

    Prepared by Monique Lania 23 Call Servicing Guide ProHeat 2X 9400F.doc Consumer States the Tank-In-Tank is leaking at base of the tank. Solution 1: Yes No, Fit O ring securely, problem solved Remove the Tank-Tank Assembly from the machine Empty the contents of water from the Tank-In-Tank Assembly Is the red O shaped ring on bottom of the Tank-in-Ta ...

  • Bissell BS-9400F - page 24

    Prepared by Monique Lania 24 Call Servicing Guide ProHeat 2X 9400F.doc Consumer states unit is very noisy Solution 1: This is quite normal as the unit requires a lot of power to get deep down and extract all the deeply embedded dirt out of your carpet. ...

Manufacturer Bissell Category Carpet Cleaner

Documents that we receive from a manufacturer of a Bissell BS-9400F can be divided into several groups. They are, among others:
- Bissell technical drawings
- BS-9400F manuals
- Bissell product data sheets
- information booklets
- or energy labels Bissell BS-9400F
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bissell BS-9400F.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bissell BS-9400F, service manual, brief instructions and user manuals Bissell BS-9400F. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bissell BS-9400F.

Similar manuals

A complete manual for the device Bissell BS-9400F, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bissell BS-9400F by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bissell BS-9400F.

A complete Bissell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bissell BS-9400F - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bissell BS-9400F, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bissell BS-9400F, that we can find in the current document
3. Tips how to use the basic functions of the device Bissell BS-9400F - which should help us in our first steps of using Bissell BS-9400F
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bissell BS-9400F
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bissell BS-9400F in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bissell BS-9400F?

Use the form below

If you did not solve your problem by using a manual Bissell BS-9400F, ask a question using the form below. If a user had a similar problem with Bissell BS-9400F it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)