-
HAMPTON BAY H25-LP1 Propane - page 1
FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-517a MODELS: H25-NG1 Natural Gas H25-LP1 Propane 01/03/08 H25 Direct V ent Gas Fireplace Owners & Installation Manual W ARNING: If the information in these instructions are not followed exactly , a fi re or explosion may result causing property damage, ...
-
HAMPTON BAY H25-LP1 Propane - page 2
2 Hampton ® H25-1 Direct V ent Freestanding Gas Stove HAMPT ON ® Direct V ent Freestanding Gas Stove UNIT DIMENSIONS T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Hampton ® Gas Stove by FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. The H25 is a hand crafted appliance and has been designed to provide you with all the ...
-
HAMPTON BAY H25-LP1 Propane - page 3
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 3 T ABLE OF CONTENTS SAFETY LABEL Safety Label .................................................................. 4 REQUIREMENTS MA Code - CO Detector ................................................ 5 INST ALLA TION Important Message ...................................................... 6 Speci ...
-
HAMPTON BAY H25-LP1 Propane - page 4
4 Hampton ® H25-1 Direct V ent Freestanding Gas Stove This is a copy of the label that accompanies each Direct V ent Freestanding Gas Stove. We have printed a copy of the contents here for your review . SAFETY LABEL COPY OF SAFETY LABEL FOR H25-NG1 & H25-LP1 NOTE: Hampton ® units are constantly being improved. Check the label on the unit and ...
-
HAMPTON BAY H25-LP1 Propane - page 5
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 5 REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chap ter 10 (2) Revise 10.8. 3 by adding the following a dditional requi rements: (a) For all side wall hor izontally ve nted gas fueled e quipment insta lled in every dwelling, bui lding or str ucture used in whole or in part for residential pu rpo ...
-
HAMPTON BAY H25-LP1 Propane - page 6
6 Hampton ® H25-1 Direct V ent Freestanding Gas Stove IMPORT ANT MESSAGE SA VE THESE INSTRUCTIONS The Direct V ent Freestanding Gas Stove must be installed in accordance with these instruc- tions. Carefully read all the instructions in this manual fi rst. Consult the building authority having jurisdiction to determine the need for a permit prior ...
-
HAMPTON BAY H25-LP1 Propane - page 7
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 7 INST ALLA TION Thermostat. Some areas may have further requirements, check local codes before installation. 5) This appliance is Listed for Alcove installa- tions, maintain minimum Alcove clearances as follows, minimum width of 34-3/4" (882mm), a maximum depth of 36" (914mm), and mini ...
-
HAMPTON BAY H25-LP1 Propane - page 8
8 Hampton ® H25-1 Direct V ent Freestanding Gas Stove LOCA TING YOUR GAS ST OVE When selecting a location for your stove, ensure that the clearances listed above are met as well as ensuring that there is adequate accessibility for servicing and proper operation. MANUF ACTURED MOBILE HOME ADDITIONAL REQUIREMENTS 1) Ensure that structural members ar ...
-
HAMPTON BAY H25-LP1 Propane - page 9
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 9 INST ALLA TION 9) Place the blower close to the base of the unit and feed the long red and black wires through the opening of the base of the unit and connect them to the thermodisc. 10) Feed the short red and black wires through the small hole at the base of the unit. 11 ) Mount the blower ass ...
-
HAMPTON BAY H25-LP1 Propane - page 10
10 Hampton ® H25-1 Direct V ent Freestanding Gas Stove INST ALLA TION PRECAUTIONS These venting systems are engineered products that have been designed and tested for use with the H25-NG1, and H25-LP1. The warranty will be voided and serious fi re, health or other safety hazards may result from any of the fol- lowing actions: 1) Installation of a ...
-
HAMPTON BAY H25-LP1 Propane - page 11
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 11 EXTERIOR VENT TERMINAL LOCA TIONS A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm) B= Clearance to window or door that may be opened *(12" /30cm) C= Clearance to permanently closed window *(min. 12"/30cm) D= V ertical clearance to v entilated soffi t ...
-
HAMPTON BAY H25-LP1 Propane - page 12
12 Hampton ® H25-1 Direct V ent Freestanding Gas Stove 4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ American Metal Produ ...
-
HAMPTON BAY H25-LP1 Propane - page 13
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 13 Description Simpson Direct V ent Pro ® Simpson Direct V ent GS ® Discontinued Selkirk Direct-T emp™ American Metal Products ® Amerivent Direct Metal-Fab ® Sure Seal Security Secure V ent ® Attic Insulation Shield 12” 46DV A-IS - N/A from FPI N/A N/A 4DAIS12 N/A SV4RSA Attic Insulation ...
-
HAMPTON BAY H25-LP1 Propane - page 14
14 Hampton ® H25-1 Direct V ent Freestanding Gas Stove Pipe Length V ertical T ermination Cap S torm Collar Flashing Ceiling Firestop 24" Pipe Length Adj.Pipe Length 1 1" - 14-5/8" 90 Elbow o Horizontal T ermination Cap W all Thimble Vinyl Siding S tandof f (Optional) RIGID PIPE VENTING SYSTEMS Horizontal or V ertical T erminations ...
-
HAMPTON BAY H25-LP1 Propane - page 15
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 15 INST ALLA TION Offset to V ertical T erminations V enting Arrangements - Horizontal T erminations using Dura-V ent venting system Dura-V ent Snorkel T ermination Riser V ent T ermination VENTING ARRANGEMENTS V ertical T erminations Systems for Residential Manufactured and Mobile Homes The shad ...
-
HAMPTON BAY H25-LP1 Propane - page 16
16 Hampton ® H25-1 Direct V ent Freestanding Gas Stove INST ALLA TION Horizontal V enting with T wo (2) 90 o Elbows Option V H + H1 A) 2' Min. 4' Max. B) 3' Min. 5' Max. C) 4' Min. 6' Max. D) 5' Min. 7' Max. E) 6' Min. 8' Max. Horizontal V enting with T wo (2) 90 o Elbows Option H V H + H1 A) 1&apo ...
-
HAMPTON BAY H25-LP1 Propane - page 17
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 17 H1 H V V ertical V enting with T wo (2) 90 o Elbows Option V H V + V1 A) 1' Min. 4' Max. 2' Min. B) 2' Min. 5' Max. 3' Min. C) 3' Min. 6' Max. 4' Min. D) 4' Min. 7' Max. 5' Min. E) 5' Min. 8' Max. 6' Min. V ertical V en ...
-
HAMPTON BAY H25-LP1 Propane - page 18
18 Hampton ® H25-1 Direct V ent Freestanding Gas Stove V enting Arrangements - V ertical T erminations with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces The shaded area in the diagram shows the allowable vertical terminations. Note: Must remove 4 screws from stove collar and rotate 130 o to have colla ...
-
HAMPTON BAY H25-LP1 Propane - page 19
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 19 DV ST OVE HORIZONT AL VENT KIT (#946-1 16 & #946-216) INST ALLA TION Review the following sequence of instructions which are typical of most installations. The se- quence may vary depending on wall thickness. See the "Exterior V ent T erminal Locations" section for vent location ...
-
HAMPTON BAY H25-LP1 Propane - page 20
20 Hampton ® H25-1 Direct V ent Freestanding Gas Stove INST ALLA TION Note: The pipe seam should be facing down. Note: T o make the installation more aes- thetically pleasing, we recommend framing out a square that the cap can be mounted on. 3) Attach the 4" dia. fl ex liner to the vent ter- minal ensuring that the fl ex overlaps the collar ...
-
HAMPTON BAY H25-LP1 Propane - page 21
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 21 Pipe Length (max. 18") Part (6-5/8" Dia) (4" Dia.) Decorative W all T rim Part #640-545/P Horizontal T erminal Part# 640-530/P W all Thimble Part # 946-202 (required for combustible walls) Vinyl Siding S tandoff (Optional) Part #946-205 Adapter Part #946-219/P (required) INST AL ...
-
HAMPTON BAY H25-LP1 Propane - page 22
22 Hampton ® H25-1 Direct V ent Freestanding Gas Stove Dura-V ent Basic Horizontal Kit # 970 1 90 o Elbow 1 W all Thimble Cover 1 Horiz. Sq. T erm. Cap DURA-VENT TERMINA TION KIT Planning Y our Dura-V ent Installation There are two basic types of Dura-V ent Direct V ent System installations: horizontal termination and vertical termination. Confi ...
-
HAMPTON BAY H25-LP1 Propane - page 23
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 23 INST ALLA TION Y ou will require the following components with your new Direct V ent Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer . Note: These are the minimum pieces re- quired. Ot ...
-
HAMPTON BAY H25-LP1 Propane - page 24
24 Hampton ® H25-1 Direct V ent Freestanding Gas Stove INST ALLA TION Diagram 7 VERTICAL TERMINA TIONS 1) Maintain the 1-1/2" clearances, except when passing through a wall, ceiling, or at the termination where the use of a fi restop or wall thimble reduces the required clearance to 1". Do not pack air spaces with insulation. Check the ...
-
HAMPTON BAY H25-LP1 Propane - page 25
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 25 INST ALLA TION Offset Chart Diagram 12 7) Ensure vent is vertical and secure the base of the fl ashing to the roof with roofi ng rails, slide storm collar over the pipe section and seal with a mastic. 8) Install the vertical termination cap by twist locking it. Notes: a) For multistorey vert ...
-
HAMPTON BAY H25-LP1 Propane - page 26
26 Hampton ® H25-1 Direct V ent Freestanding Gas Stove CONVERTING CLASS- A MET AL CHIMNEY OR MASONR Y CHIMNEY T O DIRECT VENT SYSTEM There are two different types of direct vent conversion systems listed below . Follow the appropriate directions for your installation. A) Through an existing factory built metal chimney going through the ceiling: A ...
-
HAMPTON BAY H25-LP1 Propane - page 27
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 27 AERA TION ADJUSTMENT The burner aeration is factory set but may need adjusting due to either the local gas supply , air supply or altitude. Natural Gas 3-16" (4.76 mm) Propane 1/4" (6.4 mm) The aeration adjustment gears are located on the right side of the burner box. Remove the Hamp ...
-
HAMPTON BAY H25-LP1 Propane - page 28
28 Hampton ® H25-1 Direct V ent Freestanding Gas Stove INST ALLA TION GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping ...
-
HAMPTON BAY H25-LP1 Propane - page 29
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 29 INST ALLA TION CONVERSION KIT #434-969 FROM NG T O LP THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Each Kit contains one LPG Conversion Kit and one DC Sparker Kit. LPG Conversion Kit Contains: Qty . Part # Description 1 904-163 Burner Orifi c ...
-
HAMPTON BAY H25-LP1 Propane - page 30
30 Hampton ® H25-1 Direct V ent Freestanding Gas Stove W ARNING! Do not overtighten the screw . Recommended to grip the wrench by the short side. 7 ) T urn control knob to the “OFF” position. 8 ) Remove the black protection cap by hand from the high-low knob (Fig.1). 9 ) Insert a 5/32” or 4mm Allen wrench into the hexagonal key-way of the sc ...
-
HAMPTON BAY H25-LP1 Propane - page 31
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 31 Installation of the DC Sparker for the H25-1 Unit Only: 1) Remove the control panel by unscrewing the 2 screws. 3) Plug up the Piezo hole with the plastic bushing. 4) Attach the DC sparker generator connector to the valve with a screw . 5) Remove the stove’s rear panel by unscrew- ing the tw ...
-
HAMPTON BAY H25-LP1 Propane - page 32
32 Hampton ® H25-1 Direct V ent Freestanding Gas Stove A) D) B) C) LOG SET INST ALLA TION 1) Shut off the gas supply . 2) Lift off the Cast T op and remove the Glass Front (see manual). 3) Carefully remove the logs from the box and unwrap them. The logs are fragile, handle with care - do not force into position. 4) Place the rear log on the 2 rear ...
-
HAMPTON BAY H25-LP1 Propane - page 33
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 33 6) T ake the embers and place on the burner in the space between the 2 front logs. Do not put embers on the burner in the area between the front logs and the rear log. See photo below . Separate platinum embers and place at the front of the burner in and around where the embers are placed. Avo ...
-
HAMPTON BAY H25-LP1 Propane - page 34
34 Hampton ® H25-1 Direct V ent Freestanding Gas Stove CAUTION Do not connect the millivolt remote control wires to the 120V wires. 3) Install 3 AAA alkaline batteries in transmitter and 4 AA alkaline batteries in the receiver . Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote contro ...
-
HAMPTON BAY H25-LP1 Propane - page 35
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 35 WIRING DIAGRAMS CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous opera- tion. If any of the original wires as supplied with the appliance must be replaced, it must be replaced with CSA type SEW (200 o C) or its equivalent. ...
-
HAMPTON BAY H25-LP1 Propane - page 36
36 Hampton ® H25-1 Direct V ent Freestanding Gas Stove W ARNING: Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. INST AL ...
-
HAMPTON BAY H25-LP1 Propane - page 37
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 37 AUT OMA TIC CONVECTION F AN OPERA TION The fan operates automatically - turn the knob at the top right rear corner to adjust to the de- sired speed. The fan will turn on as the stove comes up to operating temperature. After the unit has been turned off and the unit cooled to below a useful hea ...
-
HAMPTON BAY H25-LP1 Propane - page 38
38 Hampton ® H25-1 Direct V ent Freestanding Gas Stove COPY OF THE LIGHTING PLA TE INSTRUCTIONS OPERA TING INSTRUCTIONS 1) Push in gas control knob slightly and turn to “PILOT” position. 2) Push in control knob all the way and hold in until the pilot lights up. Continue to hold the control knob in for about 20 seconds after the pilot is lit. R ...
-
HAMPTON BAY H25-LP1 Propane - page 39
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 39 MAINTENANCE T op View of pilot fl ame MAINTENANCE INSTRUCTIONS 1) Always turn off the valve before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year . When cleaning the logs, use a soft clean ...
-
HAMPTON BAY H25-LP1 Propane - page 40
40 Hampton ® H25-1 Direct V ent Freestanding Gas Stove T o Remove Fan: 1) Unplug or disconnect power source to stove. 2) Remove the rear access panel on the back of the stove by removing the 2 screws under the rear panel, then lift off the 2 screws at the top. T ake care not to cut wires when lowering the panel. F AN MAINTENANCE If your fan requir ...
-
HAMPTON BAY H25-LP1 Propane - page 41
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 41 11 ) Carefully lift the burner tray assembly out. REMOVING V AL VE If your valve requires maintenance or replace- ment, use the following instructions: Not e: Always close off the gas supply before removing the valve. 1) If optional fan is installed, disconnect power source to stove. 2) Remove ...
-
HAMPTON BAY H25-LP1 Propane - page 42
42 Hampton ® H25-1 Direct V ent Freestanding Gas Stove P ARTS LIST MAIN ASSEMBL Y 1) 942-421** Casting - T op 3) 942-381** Casting - Leg 4) 942-431** Casting - Side 5) 942-441** Casting - Front 6) 350-921** Casting - Front Deco Grill 7) 942-461** Casting - Skirt 8 ) 2 6 03 50 Gasket for Rear Relief Plate 9) 290-015 Rear Relief Plate 350-524 Front ...
-
HAMPTON BAY H25-LP1 Propane - page 43
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 43 I L P O T O L 68 67 68 66 87 75 89 70 69 63 64 60 86 65 71 82 80 73 74 88 90 BURNER & LOG ASSEMBL Y 350-574/P V alve Assembly S.I.T . - Natural Gas 60) 910-478 V alve S.I.T . - Natural Gas / Propane 904-430 #42 Orifi ce - N.G. 63) 910-190 Piezo Ignitor & Nut 64) 908-672 Control Panel ...
-
HAMPTON BAY H25-LP1 Propane - page 44
44 Hampton ® H25-1 Direct V ent Freestanding Gas Stove NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ____________________________ ...
-
HAMPTON BAY H25-LP1 Propane - page 45
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 45 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ____________________________ ...
-
HAMPTON BAY H25-LP1 Propane - page 46
46 Hampton ® H25-1 Direct V ent Freestanding Gas Stove NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ____________________________ ...
-
HAMPTON BAY H25-LP1 Propane - page 47
Hampton ® H25-1 Direct V ent Freestanding Gas Stove 47 W ARRANTY Hampton Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limited lifet ...
-
HAMPTON BAY H25-LP1 Propane - page 48
48 Hampton ® H25-1 Direct V ent Freestanding Gas Stove Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________ ...
Do you have a question concerning HAMPTON BAY H25-LP1 Propane?
Use the form below
If you did not solve your problem by using a manual HAMPTON BAY H25-LP1 Propane, ask a question using the form below. If a user had a similar problem with HAMPTON BAY H25-LP1 Propane it is likely that he will want to share the way to solve it.