English dropdown-ico

Manual Makita JN3201

24 pages 1.07 mb
Download

Go to site of 24

Summary
  • Makita JN3201 - page 1

    1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES DOUBLE INSULA T ION DOUBLE ISOLA T ION DOBLE AISLAMIENT O IMPORT ANT : Read Before Using. IMPORT ANT : Lire avant usage. IMPORT ANTE: Leer antes de usar . Nibbler Grignoteuse Roedora JN3201 013354 ...

  • Makita JN3201 - page 2

    2 ENGLISH (Orig inal instruct ions) SPECIFICA TIONS Model JN3201 Mild steel 3.2 mm / 10 ga S tainless 2.5 mm / 13 ga Max. cutting capacities Aluminum 3.5 mm / 10 ga Outside edge 128 mm (5-1 /16") Min. cutting radi us Inside edge 120 mm (4-3/4") S trokes per minut e 1,300 Overall leng th 225 mm (8-7/8") Net weight 3.4 kg (7.4 lbs) • ...

  • Makita JN3201 - page 3

    3 14. Do not overreach. Keep proper footing and balance at all tim es. This enables better co ntrol of the power tool in unexpected situations. 15. Dress properly . Do not we ar loose clothing or jewellery . Keep your hair, clothing, and gloves away from moving part s. Loose clothes, jewellery or long hair can be caught in mov ing part s. 16. If de ...

  • Makita JN3201 - page 4

    4 GEB028-2 NIBBLER SAFETY W ARNIN GS 1. Hold the too l firmly . 2. Secure the workpiece firmly . 3. Keep hands away from moving p arts. 4. Edges and chips of the workpiece are sharp. Wear gloves. It is also recommended that you put on thickly bottomed shoes to prevent injury . 5. Do not put the tool on the chips of the workpiece. Otherwise it can c ...

  • Makita JN3201 - page 5

    5 ASSEMBL Y CAUTION : • Always be sure th at the tool i s switched of f and unplugged before carrying out any work on the tool. Punch replacement 1 2 3 013357 Fit the wrench pro vided onto the lock nu t and tap the handle lightly with a hammer to loosen the lock nut. T ak e off the die ho lder and us e a wrenc h to remo ve the screw . Then remove ...

  • Makita JN3201 - page 6

    6 There is more vibration when cutting stainless steel than mild steel. Less v ibration and better cutting is possible by adding another w asher (stan dard equipment) beneath the die. Use the hex w rench provided to remove the tw o screws and insert the w asher below the die . Replace screws and tighten securely . MAINTENANCE CAUTION : • Always b ...

  • Makita JN3201 - page 7

    7 OPTIONAL ACCESSORIES CAUTION : • These accessori es or atta chments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or atta chments might present a risk of injury to persons. Only use accessory or attachment for it s stated purpose. If you need any assista nce for more details regarding t ...

  • Makita JN3201 - page 8

    8 FRAN Ç AIS (Mode d ’ emploi o riginal) SP É CIFICA TIONS Modèle JN3201 Acier doux 3,2 mm / 10 ga Acier inoxydabl e 2,5 mm / 13 ga Capacités de coupe max. Aluminium 3,5 mm / 10 ga Bord extérie ur 128 mm (5-1/1 6") Rayon de coup e min. Bord intérie ur 120 mm (4-3/4 ") Nombre d'imp acts par minut e 1 300 Longueur tot ale 225 m ...

  • Makita JN3201 - page 9

    9 Sécurité personnelle 10. Restez alerte, attentif à vos mouvement s et faites preuve de bon sens lorsque vous utilisez un outil électrique. Évitez d'utiliser un outil électrique si vous êtes fatigué ou si v ous avez pris une drogue, de l'alcool ou un médicament. Un moment d'inattenti on pendant l'utilisation d'un ...

  • Makita JN3201 - page 10

    10 produit. Un cordon qui est trop petit entraînera une baisse dans la tension composée, ce qui causera une perte d'énergie et un surchauf fage. Le t ableau 1 indique la dimension de cordon à utilise r , en fonction de la longueur du cordon et de l'intensité nominale figurant sur la plaque signa létique. En ca s de doute, u tilisez ...

  • Makita JN3201 - page 11

    11 DESCRIPTION DU FONCTIONNEMENT AT T E N T I O N : • Assurez-vous toujours que l'outil est hors ten sion et débranché av ant de l'ajuster ou de vérifier son fonctionnement. Ep aisseur de coupe a dmissible 1 2 013355 L'épaisseur d u matériau à dé couper dépend de la densité du matériau lui-même. La rainure du porte- matr ...

  • Makita JN3201 - page 12

    12 1 2 3 4 5 004785 UTILISA TION AT T E N T I O N : • Maintenez fermement l’outil d’une main, par le manche princip al, lors de l’utilisa tion de l’outil. Pr è graissage Appliquez de l'huile à mach ine sur la ligne de coupe, pour assurer une plus longue durée de serv ice au poinçon et à la m atrice. Cela est tout p articulièrem ...

  • Makita JN3201 - page 13

    13 1 2 004793 Lors de l'installatio n de la matrice, un jeu de 3 .5 à 4.0 mm (1/8 à 5/32 po ) doit être obte nu en fixant une ou les deux rondelles fournies, tel qu'indiq ué sur la figure. L'outil vibrera pendant la coupe si un jeu adéquat n'est pas fourni. 1 2 3 004794 AT T E N T I O N : • Les vis doiv ent être install? ...

  • Makita JN3201 - page 14

    14 GARANTIE LIMITÉE D’UN AN MAKIT A Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir a ...

  • Makita JN3201 - page 15

    15 ESP A Ñ OL (Instrucciones originales) ESPECIFICACIONES Modelo JN3201 Especificaciones el éctricas en México 120 V 6,2 A 50/60 Hz Acero templado 3,2 mm / 10 ga Acero inoxidabl e 2,5 mm / 13 ga Capacidad m áxima de corte Aluminio 3,5 mm / 10 ga Borde exte rior 128 mm (5-1/16" ) Radio mínimo de cor te Borde interior 120 mm (4 -3/4") ...

  • Makita JN3201 - page 16

    16 9. Si no es posible evitar usar una herramient a eléctrica en condici ones húmedas, utilice un alimentador protegido con interruptor de circuito de falla e n tierra (ICFT). El uso de un ICFT reduce el riesgo de descarga e léctrica. Seguridad personal 10. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común ...

  • Makita JN3201 - page 17

    17 buenas condicion es. Cuando utilice un cable de extensión, asegúrese de utilizar uno del calibre suficiente p ara conducir la corriente que demande el producto. Un cable de calibre inferior ocasio nará una caída en la ten sión de línea y a su v ez en una pérdida de potencia y sobrecalent amiento. La T abla 1 muestra la medida correct a a ...

  • Makita JN3201 - page 18

    18 DESCRIPCI Ó N DEL FUNCIONAMIENTO PRECAUCIÓN: • Asegúrese siempre de q ue la herramienta e sté apagada y de sconectada antes de ajust ar o comprobar cualquier función en la misma. Grosor de corte permitido. 1 2 013355 El grosor del material a ser cortado depende de la resistencia de tensión del material en sí. La ranura en el sujetador d ...

  • Makita JN3201 - page 19

    19 1 2 3 4 5 004785 OPERACI Ó N PRECAUCIÓN: • Sujete la herramienta co n firmeza con una mano en la empuñadura princip al al estar usándola. Prelubricado Cubra la línea de corte con aceite p ara maquinara para incrementar el tiempo de vida útil del perforador y el troquel. Esto es p articularmente importante al estar cortando aluminio. M é ...

  • Makita JN3201 - page 20

    20 Perforador Reemplace tras 150 m (492 pies) de láminas de acero de 3,2 mm (1/8") Troquel Afile tras 300 m (984 pies) de láminas de acero de 3,2 mm (1/8") 006440 Afile el troquel cuando el corte es ineficiente inclu so tras haber reemplazado el perforad or . Realice un desgaste del borde desafila do que se muestr a en la figura con una ...

  • Makita JN3201 - page 21

    21 • Arandela de ajuste de la altura del troquel NOT A: • Algunos de los artículo s en la list a puede que vengan junto con el p aquete de la herramient a como accesorios incluidos. Puede que estos accesorios varíen de p aís a país. GARANTÍA LIMIT ADA MAKIT A DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada her ...

  • Makita JN3201 - page 22

    22 ...

  • Makita JN3201 - page 23

    23 ...

  • Makita JN3201 - page 24

    24 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry pro ...

Manufacturer Makita Category Impact Driver

Documents that we receive from a manufacturer of a Makita JN3201 can be divided into several groups. They are, among others:
- Makita technical drawings
- JN3201 manuals
- Makita product data sheets
- information booklets
- or energy labels Makita JN3201
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita JN3201.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita JN3201, service manual, brief instructions and user manuals Makita JN3201. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita JN3201.

Similar manuals

A complete manual for the device Makita JN3201, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita JN3201 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita JN3201.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita JN3201 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita JN3201, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita JN3201, that we can find in the current document
3. Tips how to use the basic functions of the device Makita JN3201 - which should help us in our first steps of using Makita JN3201
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita JN3201
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita JN3201 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita JN3201?

Use the form below

If you did not solve your problem by using a manual Makita JN3201, ask a question using the form below. If a user had a similar problem with Makita JN3201 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)