English dropdown-ico

Manual Graco Inc. 801-392

12 pages 0.8 mb
Download

Go to site of 12

Summary
  • Graco Inc. 801-392 - page 1

    This manual contains IMPORTANT WARNINGS and INSTRUCTIONS- READ AND RETAIN FOR REFERENCe 2104E.MODEL 800-053 SERIES "A" 2 150 psi (1 50 bar) OPERA TlNG PRESSURE 2250 psi (155 bar).MAXIMUM WORKING PRESSURE ...

  • Graco Inc. 801-392 - page 2

    ~~JJj~~~~Q,&! [=;'b~~.j~~~ Fluids under high pressure from spray or leaks can penetrate the skin and cause extremely serious injury, including .the need for amputation. NEVER point the spray gun at anyone or any part of the body. NEVER put hand or fingersover the spray tip. NEVER try to stop or deflect leaks with your hand or body. ALWAYS ...

  • Graco Inc. 801-392 - page 3

    , ..-.. : : REMOVE TAPE FROM PUMP CAP !’ I SPRAY GUN SPRAY HOSE r .. . .. :, .. L:’: ..,< , ... .~ Check Electrical Service and Plug In Before plugging in the sprayer. be sure the electrical service is 3 phase 220 V, 60 HAC. 20 Amp. With the ON-OFF switch in the OFF position, plug the power supplY cord into a grounded outlet. If you use an ...

  • Graco Inc. 801-392 - page 4

    OPERATlQM : Startup ' . Before starting, be sure'to read the safety warnings and setup instructions. Turn on the water supply. Trigger the gun to release any back pressure. CAUTION I ', to the pump will result. Always be sure water Never run the cleaning unit dry. Costlydamage necessary. supply iscompletelyturned on before operating. ...

  • Graco Inc. 801-392 - page 5

    . .. .I .. . . : .. ” .. : . -. PROBLEM -0w~pressure. ’ump runs extremely rough, Iressure low. Nater leakage from under :he manifold. Nater in pump crankcase. :requent or premature ailure of the packing. ;trow surging at the inlet lnd low pressure on the lischarge side. CAUSE Worn nozzle. Belt slippage. Air leak in inlet plumbing. Relief valve ...

  • Graco Inc. 801-392 - page 6

    ectrtc motor wont run. Electric motor runs, but no output. CAUSE Power cord unplugged, or building circuit fuse blown Overload switch has opened. Power.cord unplugged, or building circuit fuse blown, Overload breaker has opened. Extension cord. Tip plugged. Displacement pump frozen or gear train damage. Check, replace Unplug power cord+, decrease p ...

  • Graco Inc. 801-392 - page 7

    ,. . ,. , :. ..,,. Plungers Photo 4. 1)Using an M1 1 wrench, 2) Slide out the seal retainer with remove the plunger retainer. oil wick and rubber barrier slinger. 3) With a slight twisting motion, loosen the plunger from the plunger rod and remove. NOTE: The stud may remain when removed. with the retainer Disassemble and screw stud into plunger rod ...

  • Graco Inc. 801-392 - page 8

    8 801-392 ...

  • Graco Inc. 801-392 - page 9

    i ! , Ref. No. 50 Includes items 51-66 62 -52 63 PARTS LIST REF PART DESCRIPTION NO. NO. 1 HOSE & GUN ASSY. see aun 2 4 3 5 8 6 9 10 13 11 14 17 16 19 18 20 21 22 23 24 25 801-001 800-036 800-01 5 800-037 801-390 801 -285 801 -231 801-140 801-129 801-131 801-221 801-382 801 -379 801-292 801 -380 801 -021 801 -088 801-298 801 -302 801-082 801-08 ...

  • Graco Inc. 801-392 - page 10

    REF PART DESCRIPTION NO. NO. Qn Items 77-90 are pump internal replacement parts. See exploded view of pump for details. 77 801-027 , CAP 79 801-267 . DISCHARGE 78 801-028 . O-RING, cap MANIFOI n 80 81 82 83 84 85 86 87 88 801-038 . RING, backup 89 801-039 . O-RING 90 801-040 . RETAINER, plunge1 . . . . - . . - . - - 1 1 1 3 3 3 3 3 3 3 3 3 3 3 numb ...

  • Graco Inc. 801-392 - page 11

    PARTS DWAVVlMG Gun and Hose Assern I-3 '7 8 14 5 A Repair Kit 801 -083 Includes items A, B, C. D, E and F SERVICE 1. Re'move the 8 screws from the body halves (3) and (4). See the Parts Drawing. Separate the body halves. 2. Remove the Plug (14). spring (5) and ball (A) from the valve body (G). 3. Remove the snap ring (6). Then remove the ...

  • Graco Inc. 801-392 - page 12

    ACCESSORIES (Must be purchased separately) CHECK VALVE 801 -1 33 CHEMICAL INJECTOR KIT 800-182 supply. lnstatl upstream from pump. Prevent back up of contaminated water into fresh For injecting harsh cleaning chemicals downstream from pump. WATER SANDBLASTER 800-103 ADJUSTABLE SAND SAVER 800-031 For abrasive cleaning of stubborn dirt and paint. For ...

Manufacturer Graco Inc. Category Pressure Washer

Documents that we receive from a manufacturer of a Graco Inc. 801-392 can be divided into several groups. They are, among others:
- Graco Inc. technical drawings
- 801-392 manuals
- Graco Inc. product data sheets
- information booklets
- or energy labels Graco Inc. 801-392
All of them are important, but the most important information from the point of view of use of the device are in the user manual Graco Inc. 801-392.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Graco Inc. 801-392, service manual, brief instructions and user manuals Graco Inc. 801-392. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Graco Inc. 801-392.

Similar manuals

A complete manual for the device Graco Inc. 801-392, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Graco Inc. 801-392 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Graco Inc. 801-392.

A complete Graco Inc. manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Graco Inc. 801-392 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Graco Inc. 801-392, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Graco Inc. 801-392, that we can find in the current document
3. Tips how to use the basic functions of the device Graco Inc. 801-392 - which should help us in our first steps of using Graco Inc. 801-392
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Graco Inc. 801-392
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Graco Inc. 801-392 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Graco Inc. 801-392?

Use the form below

If you did not solve your problem by using a manual Graco Inc. 801-392, ask a question using the form below. If a user had a similar problem with Graco Inc. 801-392 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)