English dropdown-ico

Manual GE ZIFS36N LH

20 pages 0.32 mb
Download

Go to site of 20

Summary
  • GE ZIFS36N LH - page 1

    GE Monogram ® Installation Instructions Stainless Steel 36" Built-In Refrigerators and Freezers Models ZIRS36N LH – All Refrigerator ZIRS36N RH – All Refrigerator ZIFS36N LH – All Freezer ZIFS36N RH – All Freezer www.monogram.com ...

  • GE ZIFS36N LH - page 2

    2 Before you begin – Read these instructions completely and carefully. IMPORT ANT – Save these instructions for local inspector’ s use. IMPORT ANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer . Note to Consumer – Keep these instructions with your Owner’ s Manua ...

  • GE ZIFS36N LH - page 3

    3 Design Information 36" Stainless Steel Refrigerators, Freezers Flush or Semi-Flush Enclosure Installations T rue Flush Installation In a flush installation, the refrigerator door will align evenly with the front face of adjacent cabinet doors. The refrigerator blends into the surrounding cabinetry . Semi-Flush Installation These refrigerator ...

  • GE ZIFS36N LH - page 4

    4 Design Information 36" Stainless Steel Refrigerators, Freezers Side By Side Installation Of Freezer And Refrigerator For a complete food storage center , install a Monogram Freezer and Refrigerator side by side. For even more capacity , install two refrigerators and one or two freezers. • Order ZUGSS Unified Grille Panel Kit for one contin ...

  • GE ZIFS36N LH - page 5

    5 Design Information 36" Stainless Steel Refrigerators, Freezers Installation At End-of-Run Frameless Cabinets NOTE: 1/2" thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width, (36” or 72" for two models) to calculate the rough-in dimension. The leading (front) edge must be finish ...

  • GE ZIFS36N LH - page 6

    6 Installation Preparation 36" Stainless Steel Refrigerators, Freezers Electrical and Water Connection Locations The water line can be routed through the floor or back wall. • The icemaker water line should be: – Approximately 3-1/2" from the floor on the back wall, or 3-1/2" from the back wall on the floor . – At least 5" ...

  • GE ZIFS36N LH - page 7

    7 Installation Preparation 36" Stainless Steel Refrigerators, Freezers Grounding the Refrigerator IMPORT ANT – (Please read carefully) FOR PERSONAL SAFETY , THIS APPLIANCE MUST BE PROPERL Y GROUNDED. The power cord of this appliance is equipped with a 3-prong (grounding) plug that mates with a standard three-prong (grounding) wall receptacle ...

  • GE ZIFS36N LH - page 8

    8 Installation Preparation 36" Stainless Steel Refrigerators, Freezers T ools Required • T insnips to cut banding • Stepladder • Bucket • Level • 1-1/4" open-end wrench • Appliance hand truck • T ubing cutter • 7/16" open-end wrench • #2 Phillips screwdriver • Stubby Phillips screwdriver Materials Required • 2x4 ...

  • GE ZIFS36N LH - page 9

    9 Installation 36" Stainless Steel Refrigerators, Freezers • A cold water supply is required for automatic icemaker operation. The water pressure must be between 20 and 120 p.s.i. • Route 1/4" OD copper or GE SmartConnect ™ tubing between house cold water line and the water connection location. • T ubing should be long enough to e ...

  • GE ZIFS36N LH - page 10

    10 Installation 36" Stainless Steel Refrigerators, Freezers • Side panels are required whenever the sides of the product will be exposed and when installed between frameless cabinets. See pages 3 and 4. • Side panels are not required when installed into an enclosure. • Side panel installation will be determined by the design of the side ...

  • GE ZIFS36N LH - page 11

    11 Installation 36" Stainless Steel Refrigerators, Freezers Step 5 Level Refrigerator These products have a 4-point leveling system. The front is supported by leveling legs, the rear is supported by wheels. • Adjust rear wheels beneath the product to just barely touch the 2x4 block. • T urn the 7/16" hex nut located above the front wh ...

  • GE ZIFS36N LH - page 12

    12 Installation 36" Stainless Steel Refrigerators, Freezers Step 8 Check Power Step 9 Mount T op Grille Panel For shipping purposes, the top case trim is secured at 84" installation height. T o raise case trim to 84-1/2" installation height or to lower case trim to 83-1/2": • Loosen 2 screws on both sides and raise or lower th ...

  • GE ZIFS36N LH - page 13

    13 Installation 36" Stainless Steel Refrigerators, Freezers Step 11 Install T oekick • A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tighten screws. IMPORTANT: The vented toekick must remain unobstructed for proper air circulation and operation. • Set temperature control at “ 5 ” . IMPORTA ...

  • GE ZIFS36N LH - page 14

    14 ZUGSS T rim Kit Unified Stainless Steel Custom Grille Panel T ools and Materials Required: • #1 and #2 Phillips screwdrivers or sockets • 1/4" angled wrench and 1-1/2" open ended wrench • Drill and appropriate bits • Custom grille panel • Safety glasses • Gloves to protect against sharp edges Parts List: A. Soffit V ent T o ...

  • GE ZIFS36N LH - page 15

    15 • Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4 mounting brackets provided using #12 or #14 wood screws. • Secure the brackets with wood block to the back wall so that it is 84" (or your installation height) from the finished floor . Use #12 or #14 wood screws. See illustration. • Screws must penetrat ...

  • GE ZIFS36N LH - page 16

    16 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 5 Install Center T rim Strip • Open doors fully . • Starting at the top, press trim strip over inside case trims of both products. • Continue pressing trim until you reach the bottom of the case trims. The trim will align with the top and bottom of the case trim. Case Trim U-Shape T ...

  • GE ZIFS36N LH - page 17

    17 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 7 Install Grille Base Cover • Open doors fully . • Install the double width grille base cover by slipping the notched ends over the hinges. • Place wire fence over the grille base cover (textured side out). Drive original wire fence screws through the fence, the grille base cover an ...

  • GE ZIFS36N LH - page 18

    18 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 9 Install Soffit V ent T op • Separate the top and hinge side trim pieces by removing side screws. Discard top piece; retain screws. • Install one end piece to unified top piece with 2 original screws. • Slip end of rubber dust gasket into end of top unified piece and slide trim tow ...

  • GE ZIFS36N LH - page 19

    19 ZUGSS T rim Kit Unified Stainless Steel Grille Panel Step 11 Adjust Door Alignment Check door alignment. The top of the door should be parallel with the grille panel. If the door appears to be too high or too low on the handle side, adjustments can be made. • Use a 5/16" wrench to turn the hinge. • T o raise the door , turn adjustable h ...

  • GE ZIFS36N LH - page 20

    Pub. No. 49-60073-3 Part No. 197D3003P001 12-03 JR 65161-01 Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specification ...

Manufacturer GE Category Refrigerator

Documents that we receive from a manufacturer of a GE ZIFS36N LH can be divided into several groups. They are, among others:
- GE technical drawings
- ZIFS36N LH manuals
- GE product data sheets
- information booklets
- or energy labels GE ZIFS36N LH
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE ZIFS36N LH.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE ZIFS36N LH, service manual, brief instructions and user manuals GE ZIFS36N LH. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE ZIFS36N LH.

Similar manuals

A complete manual for the device GE ZIFS36N LH, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE ZIFS36N LH by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE ZIFS36N LH.

A complete GE manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE ZIFS36N LH - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE ZIFS36N LH, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE ZIFS36N LH, that we can find in the current document
3. Tips how to use the basic functions of the device GE ZIFS36N LH - which should help us in our first steps of using GE ZIFS36N LH
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE ZIFS36N LH
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE ZIFS36N LH in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE ZIFS36N LH?

Use the form below

If you did not solve your problem by using a manual GE ZIFS36N LH, ask a question using the form below. If a user had a similar problem with GE ZIFS36N LH it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)