English dropdown-ico

Manual Kodak ECP-2D

20 pages 0.46 mb
Download

Go to site of 20

Summary
  • Kodak ECP-2D - page 1

    ©Eastman Kodak Company, 2006 Professional Motion KODAK VISION Color Print Control Strips, Process ECP-2D Technical Data and Crossover Information ...

  • Kodak ECP-2D - page 2

    0 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D ...

  • Kodak ECP-2D - page 3

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 1 Note: While the data presented are typical of production coatings, they do not represent standards whi ch must be met by Kodak. Varying storage, expo sure, and processin g conditions will affect results. The company reserves the right to change and improve characteristics at any time. Table ...

  • Kodak ECP-2D - page 4

    2 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D KODAK VISION Color Print Control Strips Introduction KODAK VISION Color Print Contro l Strips (Figure 1) are intended for the control of Process ECP-2D using the procedures described in KODAK Pub lication No. H-24, Processing KODAK Motion Pi cture Films, Module 1, Process Control . The cat ...

  • Kodak ECP-2D - page 5

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 3 Effects of Mechanical and Chemical Variations Figures 2 through 12 illustrate some of the photographic effects of mechanical and chemical variations on KODAK VISION Color Print Control Strips exposed on 2383 Film compared to effects on b atch codes 6101 (35 mm) and 6102 (16 mm) and above. E ...

  • Kodak ECP-2D - page 6

    4 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D Developer Mechanical Factors Figure 2 Effects of Tim e and Temperature Varia tions —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_TEMP_TIME HD MD LD D-Min HD-MD 0000 sec F ° New 2383 .05 RED GREEN BLUE B/W BLUE B/W RED ...

  • Kodak ECP-2D - page 7

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 5 Developer Chemical Factors Figure 3 Effects of pH an d CD-2 Variations —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_PH_CD2 3.2 3.0 2.6 g/L 2.8 2.4 10.8 10.6 pH 10.5 10.4 10.7 .10 + 0 .05 .10 .05 RED GREEN B/W BLUE New ...

  • Kodak ECP-2D - page 8

    6 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D Developer Chemical Factors Figure 4 Effec ts of NaBr and Na 2 CO 3 Variations —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_Na2C03_NaBr HD MD LD D-Min HD-MD 0000 21.1 19.1 15.1 g/L 17.1 13.1 2.12 1.72 g/L 1.52 1.32 1.9 ...

  • Kodak ECP-2D - page 9

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 7 Developer Chemical Factors Figure 5 Ef fects of Na 2 SO 3 Variations —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_Na2SO3 0000 HD-MD D-Min LD MD HD 4.7 4.35 g/L 3.95 3.7 4.45 g/L 2 3 .10 + 0 .05 .10 .05 RED GREEN B/W BL ...

  • Kodak ECP-2D - page 10

    8 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D Developer Chemical Factors Figure 6 Effects of AF-20 00 and Prebath 2 Contaminatio n —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_PREBATH2_AF2000 HD MD LD D-Min HD-MD 0000 New 2383 .05 RED GREEN BLUE B/W BLUE B/W RED ...

  • Kodak ECP-2D - page 11

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 9 Developer Chemical Factors Figure 7 Effects of CD-3 for CD-2 and Stop Bath Conta mination —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_STOPBATH_CD2_CD3 HD MD LD D-Min HD-MD 0000 100.0 25.0 50.0 0.0 34.0 17.0 0.0 52.0 m ...

  • Kodak ECP-2D - page 12

    10 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D Developer Chemical Factors Figure 8 Effec ts of Persu lfate Acceler ator and Hydr oxylamine Sulfate Conta mination —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_HYDROXY_SULF_ACCELERATOR HD MD LD D-Min HD-MD 0000 g/L g ...

  • Kodak ECP-2D - page 13

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 11 Developer Chemical Factors Figure 9 Ef fects of F-3 5B Fixer a nd NaCl Cont amination —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_NaCI_FIXER HD MD LD D-Min HD-MD 0000 3.0 2.0 g/L 0.0 1.0 1.5 0.5 0.0 1.0 mL/L g/L New ...

  • Kodak ECP-2D - page 14

    12 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D Developer Chemical Factors Figure 10 Eff ects of KI Cont amination and Wat er Dilution —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer H326_H2O_KI 0000 HD-MD D-Min LD MD HD 0 0.0 0.0 mg/L mg/L .10 + 0 .05 .10 .05 RED GREEN B ...

  • Kodak ECP-2D - page 15

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 13 Developer Chem ical Factors Figure 11 Effects of Bacterial Na 2 S and Na 2 SO 4 Contamination —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer 0000 HD-MD D-Min LD MD HD mg/L New 2383 .05 RED GREEN BLUE B/W BLUE B/W RED GREEN B ...

  • Kodak ECP-2D - page 16

    14 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D Developer Chem ical Factors Figure 12 Effects of Under- an d Over-Replenishmen t —Current VISION Con trol Strips versus b atch codes 6101 (35 mm) and 6102 (1 6 mm) in Process ECP-2D Developer HD MD LD D-Min HD-MD 0000 Old 2383 .20 .15 .10 .25 + .05 .05 0 .10 .20 .15 .25 .15 .20 .05 .10 ...

  • Kodak ECP-2D - page 17

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 15 Control-Strip Crossover Important: During the inventory crossover from the previous batch Control Strips to the new VISION Control Strips, every effort should be tak en in your operations to avoid switching back and forth. Yo ur process control will be greatly simplified by depleting your ...

  • Kodak ECP-2D - page 18

    16 KODAK VISION Color Print Co ntrol Strips, Proc ess ECP-2D Figure 13 Control-Strip Cro ssover for Process ECP-2D H326_ECP-2D MD 0.97 0.95 0.88 2.45 2.70 3.04 HD CU R R E NT LD 0.21 0.21 0.27 D-Min 0.06 0.07 0.16 HD-MD 2.07 1.75 1.57 NE W ECP-2D # 1 8111 1pm 4pm 4am 1pm 4pm 8am 1pm 4pm 1pm 1pm 1pm 12 10 10 12 11 11 11 12 12 12 12 12 12 12 11 12 10 ...

  • Kodak ECP-2D - page 19

    KODAK VISION Color Print Co ntrol Strips, Process ECP-2D 17 ...

  • Kodak ECP-2D - page 20

    Professional Motion Imaging Major Revision 12/06 Printed in U.S.A. KODAK VISION Color Print Co ntrol Strips, Process ECP-2D Technical Data and Crossover Information KODAK VISION Color Print Control Strips, Process ECP-2D ©Eastman Kodak Co mpany, 2006 KODAK Publication No. H-326 CAT 877 0018 MORE INFORMATION For more information on motion pi cture ...

Manufacturer Kodak Category Printer

Documents that we receive from a manufacturer of a Kodak ECP-2D can be divided into several groups. They are, among others:
- Kodak technical drawings
- ECP-2D manuals
- Kodak product data sheets
- information booklets
- or energy labels Kodak ECP-2D
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kodak ECP-2D.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kodak ECP-2D, service manual, brief instructions and user manuals Kodak ECP-2D. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kodak ECP-2D.

Similar manuals

A complete manual for the device Kodak ECP-2D, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kodak ECP-2D by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kodak ECP-2D.

A complete Kodak manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kodak ECP-2D - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kodak ECP-2D, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kodak ECP-2D, that we can find in the current document
3. Tips how to use the basic functions of the device Kodak ECP-2D - which should help us in our first steps of using Kodak ECP-2D
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kodak ECP-2D
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kodak ECP-2D in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kodak ECP-2D?

Use the form below

If you did not solve your problem by using a manual Kodak ECP-2D, ask a question using the form below. If a user had a similar problem with Kodak ECP-2D it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)