English dropdown-ico

Manual Xerox 701P91273

52 pages 1.17 mb
Download

Go to site of 52

Summary
  • Xerox 701P91273 - page 1

    XPrint UNIX System Printer Driver Installation SOLARIS 1.X (SUN OS) / SOLARIS 2.X XPrint Color Series 701P91273 May 1996 ...

  • Xerox 701P91273 - page 2

    ii Xerox Corporation Multinational Customer and Service Education 780 Salt Road Webster, New York 14580 © 1995 by Xerox Corporation. All rights reserved. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted, including without limitatio ...

  • Xerox 701P91273 - page 3

    Table of Contents 1 How to read this Manual _________________________________ 1-1 FTP sites where this document is available ________________________________ _________ 1-1 2 Quick Setup SOLARIS 1.X , 2.X ___________________________ 2-1 Overview: ________________________________ ________________________________ ___ 2-1 Setup: _______________________ ...

  • Xerox 701P91273 - page 4

    XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION iv Overview: ________________________________ ________________________________ __ 12-3 Setup: ________________________________ ________________________________ _____ 12-3 13 Administration _______________________________________ 13-4 Overview: ________________________________ __________________________ ...

  • Xerox 701P91273 - page 5

    XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION v ...

  • Xerox 701P91273 - page 6

    ...

  • Xerox 701P91273 - page 7

    XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 1-1 1 How to read this Manual You will see throughout this manual the reference to 49XX . 49XX is generic. When you see this, substitute the actual model name of your XPrint printer. This would be ONE of the following: 4915 4920 4925 FTP sites where this document is available You may FTP updated releas ...

  • Xerox 701P91273 - page 8

    XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 1-2 ...

  • Xerox 701P91273 - page 9

    XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 2-1 2 Quick Setup SOLARIS 1.X , 2.X Overview: Quick Setup offers the experienced System Administrator a quick route to printer installation and configuration. Setup: 1. Verify physical cable connections from your printer to the network. See Network Interface Guide 2. Assign XPrint printer an IP Address ...

  • Xerox 701P91273 - page 10

    XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 2-2 6. Insert XPrint PostScript Print Tool installation diskette #1 into the floppy drive of your system. 7. To run XPrint installation script.: Solaris 1.X USERS: From a command line, TYPE: cd /tmp [ENTER] bar xvfp /dev/rfd0 [ENTER] XeroxInstall/setup [ENTER] Solaris 2.X USERS: From a command line, TY ...

  • Xerox 701P91273 - page 11

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 3-1 3 Quick Setup NON SOLARIS UNIX Overview: Quick Setup offers the experienced System Administrator a quick route to printer installation and configuration. Setup: 1. Verify physical cable connections from your printer to the network. See Network Interface Guide 2. Assign XPrint printer an IP Address ...

  • Xerox 701P91273 - page 12

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 3-2 CHOOSE YOUR UNIX VARIETY AND PERFORM THE FOLLOWING STEPS: Berkeley BSD UNIX: Add following entry to the /etc/printcap file (as root). Use “ ps ” for “Remote Printer” entry (case sensitive). 49XX_hostname is host entry for the 49XX: 49XX : :lp=: :rm= 49XX_hostname : :rp= ps : :sd=/var/s ...

  • Xerox 701P91273 - page 13

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 4-1 4 Installation Overview SOLARIS 1.X /2.X 1. Verify physical cable connections from your printer to the network. 2. Configure your TCP/IP environment and the XPrint printer so they can communicate with each other. Details in Chapter 6 3. Install XPrint printer driver on server or station by ONE of ...

  • Xerox 701P91273 - page 14

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 4-2 ...

  • Xerox 701P91273 - page 15

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 5-1 5 Installation Overview for NON SOLARIS Workstations 1. Verify physical cable connections from your printer to the network. 2. Configure your TCP/IP environment and the XPrint printer so they can communicate with each other. Details in Chapter 6 ...

  • Xerox 701P91273 - page 16

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 5-2 ...

  • Xerox 701P91273 - page 17

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 6-1 6 TCP/IP XPrint printer Configuration Overview: The XPrint printer by default receives its TCP/IP address dynamically from a RARP or BOOTP server. To override this setting, you can set the TCP/IP address at the control panel, by telnet, or by the PC and MAC Printer Services. To set up a RARP or BO ...

  • Xerox 701P91273 - page 18

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 6-2 ...

  • Xerox 701P91273 - page 19

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 7-1 7 XPrint PostScript Print Tool Installation (Floppy Disk) Overview: Xprint is supported currently in the Sun Solaris 1.X / 2.X operating systems. The XPrint PostScript Print Tool is both a print driver and a spooling daemon. The XPrint PostScript Print Tool and print daemon work in conjunction wit ...

  • Xerox 701P91273 - page 20

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 7-2 Solaris 1.X USERS: 3. From a command line, TYPE: cd /tmp [ENTER] bar xvfp /dev/rfd0 [ENTER] XeroxInstall/setup [ENTER] Solaris 2.X USERS: NOTE: Volume Manager must be set up to recognize the floppy drive 4. From a command line, TYPE: cd /tmp [ENTER] volcheck [ENTER] cp /floppy/floppy0/setup . [ENT ...

  • Xerox 701P91273 - page 21

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 8-1 8 Installing XPrint PostScript Print Tool from a Network Installation Site. Overview: A network installation of the XPrint PostScript print tool is advisable for large numbers of installations or for simplicity sake. It is MUCH easier and faster to install XPrint from your network then from floppy ...

  • Xerox 701P91273 - page 22

    ...

  • Xerox 701P91273 - page 23

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 9-1 9 Printing Model: Workstation to printer. Overview: Run the XPrint setup utility to configure your Solaris 1.X / 2.X client to print to a network connected XPrint printer. A network connected printer is a XPrint printer that has the Network Interface Card (NIC) installed and connected to a functio ...

  • Xerox 701P91273 - page 24

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 9-2 1. From the Setup XPrint49XX menu, select option 1 . 2. TYPE: 1 [ENTER] 3. From the Add or Update a Printer menu, select option 2 until it indicates “workstation to printer”. 1. Enter a menu option number to toggle through the available settings. When the desired settings for all options are r ...

  • Xerox 701P91273 - page 25

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 10-3 10 Printing Model: Workstation to print server. Overview: You need to be a superuser to use the following procedures. Run the 49XX setup utility to configure your Solaris 1.X / 2.X client to print to a remote 49XX printer. A remote print spooler is a Solaris 1.X / 2.X workstation that has been co ...

  • Xerox 701P91273 - page 26

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 10-4 2. From the Setup XPrint49XX menu, select option 1 . Setup XPrint49XX 1) Add or Update a Printer 2) Remove an existing printer. e) Exit Existing printer list: Enter option: TYPE: 1 [ENTER] 3. From the Add or Update a Printer menu, select option 2 until it indicates “workstation to print server? ...

  • Xerox 701P91273 - page 27

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 11-1 11 Printing Model: Print server to printer Overview: Run the 49XX setup utility to configure your Solaris 1.X / 2.X client to function as a remote print spooler for lp, lpr, and other XPrint clients on your network. You can configure the remote print spooler to spool to direct connected (parallel ...

  • Xerox 701P91273 - page 28

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 11-2 2. From the Setup XPrint49XX menu, select option 1 . TYPE: 1 [ENTER] 3. From the Add or Update a Printer menu select option 2 until it indicates “print server to printer” . 4. Enter a menu option number to toggle through the available settings. When the desired settings for all options are re ...

  • Xerox 701P91273 - page 29

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 12-3 12 Removing a XPrint printer. Overview: Run the setup49XX configuration utility to remove a XPrint 49XX printer configuration from your workstation or remote print spooler. Setup: NOTE: The following instructions assume you have correctly completed the XPrint 49XX PostScript Print Tool installati ...

  • Xerox 701P91273 - page 30

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-4 13 Administration Overview: TCP/IP and lpr on the 49XX can be administrated in a number of different ways: Telnet PC XPrint Printer Services MAC XPrint Printer Services 49XX Control panel It is up to you and your environment to decide which administration utility best fits your needs. ...

  • Xerox 701P91273 - page 31

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-5 4915/4920/4925 Printer Parameters Configurable via Telnet The 49XX printer allows MOST of its Network Card (NIC) parameters to be viewed and set using Telnet. The 49XX printer NIC can also be remotely reset or initialized using Telnet. The following is a summary of Telnet configurable NIC paramet ...

  • Xerox 701P91273 - page 32

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-6 NIC Settings Ethernet: Connector Type (bnc, rj45, autoselect) TokenRing: Connector Type (db9, rj45, autoselect) Ring Speed (4mbs, 16mbs) Routing (yes/no -- source routing: enabled/disabled) Card Address (TokenRing physical address can be set) Reset Printer (yes/no -- resets NIC and enables any NI ...

  • Xerox 701P91273 - page 33

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-7 To Use Telnet: At any Telnet client (UNIX, WFW3.11, NT, DOS, ...) Telnet to port 2002 of the 49XX. NOTE: Telnet will work only if the TCP/IP protocol stack is loaded AND it supports Telnet. NOTE: In the following examples, the expression XXX.XXX.XXX.XXX refers to the IP address of your XPrint pri ...

  • Xerox 701P91273 - page 34

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-8 Checking Printer Status: Telnet offers a very quick way to determine printer status remotely via TCP/IP. Once connected to the 49XX maintenance port (2002), real-time status can be viewed remotely in the Telnet console screen. If the printer is idle, you can poll the printer by typing “s” at ...

  • Xerox 701P91273 - page 35

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-9 Remote 49XX NIC Configuration: To remotely configure the 49XX using Telnet, you can enter “maintenance mode” by typing “ ! ” at the Telnet console. Note: You can get help while in maintenance mode by typing “h” at the maintenance mode main menu. Note: You MUST reset the NIC in the pri ...

  • Xerox 701P91273 - page 36

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-10 Maintenance mode with HELP example: The following is an example of entering “maintenance mode”, then getting help : At the Command prompt TYPE: telnet XXX.XXX.XXX.XXX 2002 [ENTER] The system will attempt to connect to the host. Y ou will see: TYPE: ! [ENTER] Warning: entering the monitor wil ...

  • Xerox 701P91273 - page 37

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-11 Telnet Menu System (exploded): C Configure console (for status monitoring) Config console for status monitoring 1 (No) 2 (Yes) D Display network interface settings E Set Ethernet options Ethernet connector autoselect override 1 (BNC) 2 (RJ45) 3 (Do not override) Telnet Security 1 (Off) 2 (On/New ...

  • Xerox 701P91273 - page 38

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-12 Set primary NetWare server 1 (No) 2 (Yes) Set Novell broadcast name 1 (No) 2 (Yes) P Set PC Network (Netbeui) options Disable PC Network (Netbios)?, yes or no (y or n)?: ( y / n ) Set PC network (Netbeui) Group 1 (No) 2 (Yes) Set PC network (Netbeui) Name 1 (No) 2 (Yes) Set PC network (Netbeui) ...

  • Xerox 701P91273 - page 39

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-13 PC (WIndows) and MAC XPrint Printer Services PC (WIndows) XPrint Printer Services Full information is available for the administration of XPrint printers under Windows in the System Administration Guide supplied with your XPrint printer. If your XPrint printer is equipped with a Network Interfac ...

  • Xerox 701P91273 - page 40

    ...

  • Xerox 701P91273 - page 41

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 14-1 14 Troubleshooting TCP/IP communication problems 1. Verify that the 49XX is turned on and connected to a functioning network port. Check the 49XX NIC LEDs for activity. 2. At a command line prompt, use the ping xxx.xxx.xxx.xxx command (xxx.xxx.xxx.xxx is the IP address of the 49XX printer). Try p ...

  • Xerox 701P91273 - page 42

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 14-2 4. If you suspect that the cause of the communications problem is the 49XX printer, print out a Printer Setting page at the 49XX control panel and view the 49XX TCP/IP parameters. See Appendix A . If Dynamic IP Addressing is enabled. Try “hard coding” the 49XX IP address at the control panel. ...

  • Xerox 701P91273 - page 43

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 14-3 XPrint 49XX PostScript Print Tool printing problems: 1. Verify that the 49XX is switched on and connected to a functioning network por t. Check the 49XX NIC LEDs for activity. 2. At any workstation command line prompt, use the ping hostname command (where hostname is the hostname of the 49XX prin ...

  • Xerox 701P91273 - page 44

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 14-4 lpr and lp (NON XPrint) printing problems 1. Verify that the 49XX is switched on and connected to a functioning network port. Check the 49XX NIC LEDs for activity. 2. At any workstation command line prompt, use the ping hostname command (where hostname is the hostname of the 49XX printer as it ap ...

  • Xerox 701P91273 - page 45

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-1 15 APPENDICES Appendix A Obtaining current XPrint PRINT SETTINGS Obtain the XPrint settings by printing the PRINT SETTINGS page. The default settings enable all ports and this is suitable for most applications. To print the PRINT SETTINGS page: FROM THE PRINTER’S CONTROL PANEL 1. Press On Line ...

  • Xerox 701P91273 - page 46

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-2 Appendix B Setting the IP address with the Control Panel 1. Press On Line button on the Control Panel . Be sure the light next to it is OFF 2. Press Menu . T he ON-LINE message disappears and TOP MENU is displayed. 3. Press Up+ until <COMMUNICATIONS> appears on the Display Panel and then pr ...

  • Xerox 701P91273 - page 47

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-3 Appendix C Setting up APPSOCKET 1. Press On Line on the Control Panel . Verify the LED to the left of the button is OUT . 2. Press Menu . The ON-LINE message will disappear and TOP MENU should be displayed. 3. Press Up+ until <COMMUNICATIONS> appears on the Display Panel and then press Ente ...

  • Xerox 701P91273 - page 48

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-4 Appendix D Setting a SUBNET MASK at the Control Panel 1. Press On Line button on the Control Panel . Be sure the light next to it is OFF 2. Press Menu . The ON-LINE message disappears and TOP MENU is displayed. 3. Press Up+ until <COMMUNICATIONS> appears on the Display Panel and then press ...

  • Xerox 701P91273 - page 49

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-5 Appendix E Setting DEFAULT GATEWAY at the Control Panel 1. Press On Line button on the Control Panel . Be sure the light next to it is OFF 2. Press Menu . The ON-LINE message disappears and TOP MENU is displayed. 3. Press Up+ until <COMMUNICATIONS> appears on the Display Panel and then pres ...

  • Xerox 701P91273 - page 50

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-6 Appendix F XPrint UNIX Command Line Utilities XPQ Overview This utility is an equivalent utility to the UNIX lp command. It allows the user to view the current job list for XPrint print queues. This program executes and continues to run and update the screen until you exit by typing ^C (Control k ...

  • Xerox 701P91273 - page 51

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-7 XPRM Overview This utility is an equivalent to the UNIX lprm command. It allows the user to delete jobs currently in an XPrint job queue. Before using lprm, run the XPrint utility lpq for the desired queue and note the job number of the print job you want to delete. XPRM can be used by the ROOT u ...

  • Xerox 701P91273 - page 52

    XP rint UNIX SYSTEM PRINTER DRIVER INSTALLATION 15-8 XPMV Overview This utility allows the user to move jobs between XPrint print queues. Before using lpmv, run the XPrint utility lpq for the desired queue and note the job number of the print job you want to move. You will also need the XPrint queue names for both the source and destination queues. ...

Manufacturer Xerox Category Printer

Documents that we receive from a manufacturer of a Xerox 701P91273 can be divided into several groups. They are, among others:
- Xerox technical drawings
- 701P91273 manuals
- Xerox product data sheets
- information booklets
- or energy labels Xerox 701P91273
All of them are important, but the most important information from the point of view of use of the device are in the user manual Xerox 701P91273.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Xerox 701P91273, service manual, brief instructions and user manuals Xerox 701P91273. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Xerox 701P91273.

Similar manuals

A complete manual for the device Xerox 701P91273, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Xerox 701P91273 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Xerox 701P91273.

A complete Xerox manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Xerox 701P91273 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Xerox 701P91273, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Xerox 701P91273, that we can find in the current document
3. Tips how to use the basic functions of the device Xerox 701P91273 - which should help us in our first steps of using Xerox 701P91273
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Xerox 701P91273
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Xerox 701P91273 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Xerox 701P91273?

Use the form below

If you did not solve your problem by using a manual Xerox 701P91273, ask a question using the form below. If a user had a similar problem with Xerox 701P91273 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)