English dropdown-ico

Manual PVI Industries B40

11 pages 0.13 mb
Download

Go to site of 11

Summary
  • PVI Industries B40 - page 1

    PV500 - 22A 08 - 98 1 Section 22A INSTALLATION & MAINTENANCE MANUAL FOR PVI FIREPOWER  B40 OIL BURNER 1.0 thru 10.0 gph CARBON MONOXIDE WARNING: CAUTION: IMPROPER COMBUSTION MAY CAUSE SERIOUS INJURY. PVI recommends a seasonal or annual combustion check - out be performed by a qu alified service agency to ensure safe and efficient operation. ...

  • PVI Industries B40 - page 2

    PV500 - 22A 08 - 98 2 Section 22A PVI FIREPOWER  B40 OIL BURNER ELECTRICAL 1. Wiring to the unit should conform to the National Electrical Code or the code legally authorized to your locality. A fused disconnect switch should be used for water heater control. Service wiring connections of 115V, 1 phase, 60 Hz . are located in the enclosure on th ...

  • PVI Industries B40 - page 3

    PV500 - 22A 08 - 98 3 Section 22A PVI FIREPOWER  B40 OIL BURNER START - UP (Refer to Figure 22 - 1 to identify burner parts) 1. Remove the enclosure panel cover on the water heater or boiler to expose the control circuit. The wiring diagram, located on the backside of the cover, will show the controls used in our circuitry. 2. Visually check tha ...

  • PVI Industries B40 - page 4

    PV500 - 22A 08 - 98 4 Section 22A PVI FIREPOWER  B40 OIL BURNER START - UP (con't) After purging is complete, terminal 3 energizes the oil valve and terminal 4 energizes the ignition transformer. The flame is then established and the VDC reading on the meter should read a steady 14 - 18 VDC for photocell or 4 - 6 VDC for UV amplifiers. Each ...

  • PVI Industries B40 - page 5

    PV500 - 22A 08 - 98 5 Section 22A PVI FIREPOWER  B SERIES OIL BURNER START - UP (con't) 20. Record the following information for future use: a) Air shutter position ________________ b) Oil supply pressure ____________PSIG c) Stack draft _________________" W.C. d) O 2 reading _______________% (4 - 6%) e) CO 2 reading ____________% (10 - ...

  • PVI Industries B40 - page 6

    PV500 - 22A 08 - 98 6 Section 22A PVI FIREPOWER  SINGLE STAGE B SERIES OIL BURNER ADJUSTMENTS AIR ADJUSTMENT Loosen the locking screw and move the knob (A) along the scale (B) to the position wanted and tighten the screw. Check the air adjustment by making a flue gas analysis. Figure 22A - 2 ADJUSTMENT & REMOVAL OF NOZZLE ASSEMBLY To adjust ...

  • PVI Industries B40 - page 7

    PV500 - 22A 08 - 98 7 Section 22A PVI FIREPOWER  TWO STAGE B SERIES OIL BURNER ADJUSTMENTS AIR ADJUSTMENT First stage : Set the operating switch on low capacity. Loosen the screw (A) and move the damper ar m (C) along the scale (E) to a position where the flame does not soot nor blow out. Tighten the screw. Second stage : The operating switch re ...

  • PVI Industries B40 - page 8

    PV500 - 22A 08 - 98 8 Section 22A PVI FIREPOWER  NOZZLE POSITION INPUT - GPH NOZZLE POSITION 1.4 1 2.8 3 4.3 4 5.7 2 7.2 2 8.6 4 TABLE 22 - 2 Figure 22A - 8 ...

  • PVI Industries B40 - page 9

    PV500 - 22A 08 - 98 9 Section 22A PVI FIREPOWER  TROUBLESHOOTING SUGGESTIONS OIL BURNER 1. BURNER FAILS TO START: A. Defective on/off or fuel transfer switch. Replace switch. B. Control circuit has an open control contact. Che ck limits, low water cutoff, proof of closure switch and others as applicable. C. Bad fuse or switch open on incoming po ...

  • PVI Industries B40 - page 10

    PV500 - 22A 08 - 98 10 Section 22A PVI FIREPOWER  TROUBLESHOOTING SUGGESTIONS OIL BURNER (con't) 4. OIL FLAME IGNITES, BUT THEN FLAME SAFEGUARD CONTROL LOCKS OUT ON SAFETY: A. Flame scanner lens dirty. Remove and clean. B. Scanner si ght tube blocked or dirty. Check and clean. C. Flame scanner defective. Replace. D. Fuel/air ratios incorrec ...

  • PVI Industries B40 - page 11

    PV500 - 22A 08 - 98 11 Section 22A PVI FIREPOWER  TROUBLESHOOTING SUGGESTIONS OIL BURNER (con't) 6. OIL HIGH FIRE INPUT RATE CANNOT BE ACHIEVED: A. Oil nozzle size too small. Remove nozzle and check marking. Replace with correct size nozzle. B. Nozzle defective. Replace. Nozzle mesh filter (if supplied) dirty. Clean or replace. C. Oil suppl ...

Manufacturer PVI Industries Category Burner

Documents that we receive from a manufacturer of a PVI Industries B40 can be divided into several groups. They are, among others:
- PVI Industries technical drawings
- B40 manuals
- PVI Industries product data sheets
- information booklets
- or energy labels PVI Industries B40
All of them are important, but the most important information from the point of view of use of the device are in the user manual PVI Industries B40.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals PVI Industries B40, service manual, brief instructions and user manuals PVI Industries B40. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product PVI Industries B40.

Similar manuals

A complete manual for the device PVI Industries B40, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use PVI Industries B40 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of PVI Industries B40.

A complete PVI Industries manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual PVI Industries B40 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the PVI Industries B40, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the PVI Industries B40, that we can find in the current document
3. Tips how to use the basic functions of the device PVI Industries B40 - which should help us in our first steps of using PVI Industries B40
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with PVI Industries B40
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of PVI Industries B40 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning PVI Industries B40?

Use the form below

If you did not solve your problem by using a manual PVI Industries B40, ask a question using the form below. If a user had a similar problem with PVI Industries B40 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)