Manual Winegard SD

8 pages 0.25 mb
Download

Go to site of 8

Summary
  • Winegard SD - page 1

    1 RoadTrip ™ Digital Satellite Mobile Antenna for Two Receivers RoadTrip SD - Stationary Satellite System RoadTrip SDi - In-Motion Satellite System INSTALLATION MANUAL Made in the U.S.A. Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 319/754-0600 • FAX 319/754-0787 • www.winegard.com Printed in U.S.A. © Winegard Company ...

  • Winegard SD - page 2

    2 1 . Open box and remove packing material. 2. Lift dome out of box vertically . Then lif t unit out of box vertically . Do not turn box and “roll” out, or turn up side down to remove. 4’ Gray Coax Cable (OEM Model) 4’ White Coax Cable (OEM Model) 4’ Power Cable (OEM Model) ! Parts Included • Tools Needed • How to Unpack If using knif ...

  • Winegard SD - page 3

    3 Installation Diagram Control Unit ELEVATION MOTOR LNBF   CONTROL UNIT MUST BE PARALLEL TO THE CENTER LINE OF THE VEHICLE AND FACE FRONT OR REAR OF VEHICLE. CENTER LINE OF THE VEHICLE  GPS CABLE (RoadTrip SDi ONLY) GPS ANTENNA (RoadTrip SDi ONLY)   ...

  • Winegard SD - page 4

    4 Quick Reference Guide Your Winegard RoadTrip satellite System has been designed to be the most user-friendly Mobile Satellite Antenna on the market today. Upon installation of the antenna, or after changing satellite service provider, simply set the switches inside of the dome to the settings shown in the Operation manual. These switches enable t ...

  • Winegard SD - page 5

    5 IMPORT ANT! Do not install this system in the rain, or under any wet conditions . Mois- ture may affect electronics and void your warranty! 1. For best performance and to reduce signal ac- quisition time, park vehicle on a level surface; level the R V . 2. Select a level spot on your roof for installation. Using the chart, determine the minimum d ...

  • Winegard SD - page 6

    6 Installation 1. Connect coax cables and power wire to RV pre- wire harness. Connect gray coax to pre-wire coax for primary receiver . Connect white coax to pre-wire coax for secondary receiver . Connect power cable to pre- wire power cable. See Figure 2. 2. Place cable-entry plate over hole and cables. Screw in place. Seal plate and screw holes w ...

  • Winegard SD - page 7

    7 Connecting two receivers 1. Connect the gray coax cable coming from the RoadT rip™ to the “SA TELLITE IN” input on the primary receiver . The primary receiver is the receiver used most often and will toggle between satellites. 2. Connect the white coax cable coming from the RoadT rip™ to the “SA TELLITE IN” input on the secondary rece ...

  • Winegard SD - page 8

    8 Winegard Company • 3000 Kirkwood S treet • Burlington, IA 52601 • 319/754-0600 Fax 319/754-0787 • www .winegard.com Printed in U.S.A. © 2006, Winegard Company 2452086 ...

Manufacturer Winegard Category Satellite Radio

Documents that we receive from a manufacturer of a Winegard SD can be divided into several groups. They are, among others:
- Winegard technical drawings
- SD manuals
- Winegard product data sheets
- information booklets
- or energy labels Winegard SD
All of them are important, but the most important information from the point of view of use of the device are in the user manual Winegard SD.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Winegard SD, service manual, brief instructions and user manuals Winegard SD. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Winegard SD.

Similar manuals

A complete manual for the device Winegard SD, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Winegard SD by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Winegard SD.

A complete Winegard manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Winegard SD - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Winegard SD, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Winegard SD, that we can find in the current document
3. Tips how to use the basic functions of the device Winegard SD - which should help us in our first steps of using Winegard SD
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Winegard SD
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Winegard SD in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Winegard SD?

Use the form below

If you did not solve your problem by using a manual Winegard SD, ask a question using the form below. If a user had a similar problem with Winegard SD it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)