Manual Vermont Casting VC100

33 pages 0.68 mb
Download

Go to site of 33

Summary
  • Vermont Casting VC100 - page 1

    Gas Barbecue Grill For Models VC100, VC200 and VC400 50000444a 0801 VERMONT Castings VERMONT Castings VERMONT C astings USERS MANUAL ...

  • Vermont Casting VC100 - page 2

    Page i W arnings FOR YOUR SAFETY If you smell gas: • Shut off gas to the appliance • Extinguish any open flame • Open lid • If odor continues, immediately call your gas supplier or fir e department. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP cylind ...

  • Vermont Casting VC100 - page 3

    SIGNAL WORDS : The Signal W ords used in this Manual, and their intended meanings, are as follows : DANGER : Indicates that a failure to observe the safety instructions could result in death or catastrophic bodily injury . W ARNING : Indicates that a failure to observe the safety instructions could result in serious bodily injury . CAUTION : Indica ...

  • Vermont Casting VC100 - page 4

    Page iii A. SAFE LOCA TIONS FOR USE OF THIS OUTDOOR GRILL DANGER : • Never use this outdoor Grill inside any building, garage, shed or breezeway , or inside any boat, trailer or recreational vehicle, to prevent a possible fire and to prevent the possibility of carbon monoxide poisoning or asphyxiation. W ARNINGS : • Always confirm that this Gri ...

  • Vermont Casting VC100 - page 5

    B. SAFE USE OF LP (PROP ANE) GAS DANGER : • Never install a propane cylinder that is more than 80 % full, as the contents may lack adequate room for expansion when exposed to heat. Propane vapor may then be vented through the pressure release valve, which could accumulate in a pool and later result in a fire or explosion. Always instruct your cer ...

  • Vermont Casting VC100 - page 6

    Safety • Always promptly shut off the gas supply and immediately extinguish all flames if you smell gas. Always seek assistance from your gas supplier or local Fire Department if the gas smell persists, because of the danger of fire or explosion. • Always confirm that there are no gas leaks before lighting this Grill. Apply a 50/50 solution of ...

  • Vermont Casting VC100 - page 7

    T able of Contents Page 1 Safety Important Warnings .................................................................... i - v Clearance Requirements ............................................................. ii T able of Contents ........................................................................ 1 Fuels ................................... ...

  • Vermont Casting VC100 - page 8

    Safety Fig. 3 Fig. 2 Page 2 Check hose for breaks or wear before each use T ype I Connector Regulator Shutoff V alve Collar W ARNING: Use only the pressure regulator and and type I propane gas supply coupling and hose that is originally provided with this appliance or as specified by V ermont Castings, (see Fig. 2). ADDITIONAL W ARNINGS: • Always ...

  • Vermont Casting VC100 - page 9

    Page 3 DANGER: a) Do not store a spare LP - Gas Cylinder under or near this appliance b) Never fill the cylinder beyond 80% full; and c) If the information in a) and b) is not followed exactly , a fire causing death or serious injury may occur . W ARNING : Always confirm that the openings in the cylinder compartment of the Grill are free of any obs ...

  • Vermont Casting VC100 - page 10

    Gas Hookup Fig. 4 Fig. 5 Page 4 Hooking Up to the LP (Propane) Gas Supply For Y our Safety 1. W ARNING : Never store or use gasoline or any other volatile substance in the vicinity of this Grill. 2. W ARNING : Never store a spare propane cylinder in the vicinity of this Grill, or in the vicinity of any other potential heat source. LP (Propane) Gas ...

  • Vermont Casting VC100 - page 11

    Natural Gas Supply Connection T o Connect: 1. Push back the Sleeve on the Socket as shown below (see Fig. 6a). 2. Insert Plug and release the Sleeve (see Fig. 6b). 3. Push the Plug until Sleeve snaps forward to lock the Plug in the Socket. • W ARNING : Always conduct the following safety tests before lighting the Grill, to prevent a possible fire ...

  • Vermont Casting VC100 - page 12

    Control Functions Page 6 Propane T ank V alve W ARNING : Never open the T ank V alve unless the Grill is being prepared for use, to prevent the pooling of propane vapor . Always open the V alve immediately before lighting the Grill, and always close it immediately after cooking has been completed. Burner Control V alves On Models VC200 & VC400, ...

  • Vermont Casting VC100 - page 13

    Lighting the Main Burners Fig. 8 Fig. 9a Fig. 9b Fig. 9c Normal: Soft blue flames Out of Adjustment: Hard blue flames-too much air Poor Combustion: W avy , yellow flames-too little air Page 7 1. Always open the Hood completely and always inspect the Grill and burners to confirm that all components are properly positioned, before lighting the main b ...

  • Vermont Casting VC100 - page 14

    T urning the Burners Off Fig. 10 Page 8 1. Always turn the burner control knob(s) to the OFF position when cooking has been completed. 2. Promptly turn OFF the gas supply valve at the propane cylinder or at the main natural gas supply line. 3. Close the Hood of the Grill. Flareups “Flareups” sometimes occur when food drippings fall onto the hot ...

  • Vermont Casting VC100 - page 15

    Lighting the Oven Burner (Models VC200 & VC400) Page 9 Use of the Oven burner is ideal for the convection cooking of roasts, seafood, vegetables and pizzas. T o start the Oven burner : 1. Always open the Hood completely , before attempting to light the Grill. W ARNING : Never stand with your head directly over the Grill when preparing to light ...

  • Vermont Casting VC100 - page 16

    Lighting the Rotisserie Burner (Models VC200 & VC400) Fig. 1 1 Page 10 The Rotisserie burner provides the steady , even heat required to cook poultry and roasts to self-basted perfection. T o start the Rotisserie burner : 1. Always open the Hood completely before attempting to light the Grill. W ARNING : Never stand with your head directly over ...

  • Vermont Casting VC100 - page 17

    Rotisserie Setup (Optional to Model VC100) Fig. 12 Page 11 The Rotisserie burner is intended to be used for rotisserie cooking only . W ARNING : Never use the main burners while using the Rotisserie burner , as that could result in igniting the drippings, or overheating your Grill. The Rotisserie assembly includes a counter -weight for large or irr ...

  • Vermont Casting VC100 - page 18

    Lighting the Side Burner (Optional to Models VC100 & VC200) Fig. 13 O F F HI LO IGNITOR V AL VE CONTROL Page 12 W ARNING : Never stand with your head directly over the Grill when preparing to light the side burner , to prevent possible bodily injury . 1. T urn the side burner control knob to HI (see Fig. 13). 2. T urn the Igniter Knob clockwise ...

  • Vermont Casting VC100 - page 19

    Using the Smoker Boxes Fig. 14a Fig. 14b Page 13 Every V ermont Castings Grill is equipped with a Main Oven Burner Smoker Box integrated into the Sear Plate assembly and VC200 & 400 models have a Rotisserie Burner Smoker Box. Y ou can add a distinct, smoky flavor to your food by burning a variety of woods or herbs in this unit. 1. Always soak a ...

  • Vermont Casting VC100 - page 20

    Methods of Cooking With its combination of burners and accessories your V ermont Castings gas grill can provide for virtually every conceivable style of cooking. • The powerful Main burners deliver the middle and high range of tempera- tures desired for traditional barbecuing. This includes searing and finishing steaks, hamburgers, pork chops and ...

  • Vermont Casting VC100 - page 21

    One of the keys to extending your range of grilling capabilities is a fundamental understanding of the two common methods of cooking, Direct and Indirect cooking. In the Direct cooking method foods are placed directly above the heat source. This method is used in searing for example where you require high and immediate heat to quickly brown the out ...

  • Vermont Casting VC100 - page 22

    Grilling T ips Page 16 A few helpful hints will ensure that your grilling results are perfect every time. • Apply a light coating of cooking oil to your cooking grids before grilling, to prevent foods from sticking. • Cook similar portion sizes together , so that they all cook evenly . • Use tongs to turn foods on the Grill. • Never pierce ...

  • Vermont Casting VC100 - page 23

    T ype of Food Beef Burgers Roasts Blade, Sirloin T ip Steaks Porterhouse, Rib, Ribeye, Sirloin, T -Bone Filet Mignon Poultry Chicken, Parts Chicken, Whole Chicken Breasts, Boneless Cornish Hens Duck T urkey W eight/ Thickness 1 inch 1 inch 2 inches 3 –4 lbs. 1-2 lbs. 1–1-1/2 lbs. 4 –5 lbs. 13 –25 lbs. Cooking T ime Rare: 4-7min. Medium: 7-1 ...

  • Vermont Casting VC100 - page 24

    Cooking T emperature 400-450 ° F. 400-450 ° F. 325 –350 ° F. 325 –350 ° F. 325-350 ° F. 325-350 ° F. 375-400 ° F. 400-450 ° F. 325-350 ° F. 325-350 ° F. T ype of Food Pork Chops Ham Steak Whole ham Ribs Back, Side Roasts Butt, Loin, Shoulder T enderloin Sausage Lamb Chops Loin, Rib, Shoulder Roast Crown Roast Leg W eight/ Thickness 1 ...

  • Vermont Casting VC100 - page 25

    Cooking T emperature 325-350 ° F. 325-350 ° F. 325-350 ° F. 325-350 ° F. 325-350 ° F. 325-350 ° F. 325-350 ° F. 400-450 ° F. 325-350 ° F. 325-350 ° F. 325-350 ° F. 325-350 ° F. T ype of Food V egetables Asparagus Beans Carrots Corn on the Cob Eggplant Mushrooms Onions Peppers Potatoes Roasted Garlic T omatoes Zucchini Cooking T ime 6-8 ...

  • Vermont Casting VC100 - page 26

    Care & Cleaning Fig. 16 Page 20 W ARNING : Always observe the following safety precautions, to prevent bodily injury and to assure that your Grill will operate properly : • Always allow sufficient time for the Grill to cool fully before handling or cleaning any of its parts. Burners NOTE : All of the burners should be inspected frequently and ...

  • Vermont Casting VC100 - page 27

    Fig. 18 Fig. 17 Adjust Shutter and Keep Screen Clean Fig. 19 Page 21 Cooking Grids The cooking grids have been porcelain enameled for durability and ease of cleaning. These Grills may be cleaned with any nonabrasive cleaning agent formulated for kitchen use, or a brass wire brush. NOTE : Always handle the grids with care, as porcelain enamel is sus ...

  • Vermont Casting VC100 - page 28

    Drip T ray Fig. 20 Page 22 The drip tray located under the burner pan in the bottom of the Grill body is provided to catch excess cooking fats and juices. The drip tray is accessible from the left-hand side of the Grill, when facing it from the front. It is necessary to lift out the left-hand cabinet panel to gain access to the drip tray (see Fig. ...

  • Vermont Casting VC100 - page 29

    Maintenance Burner Adjustment Fig. 21 Page 23 Fig. 22 V entur i T ube V alv e Outlet 1/4" NOTE : It may be necessary to adjust the burners periodi- cally , to compensate for variables in gas characteristics. If you notice that the burner flame pattern is irregular (see Figs. 9a, 9b & 9c) it may be necessary to adjust the air shutter openin ...

  • Vermont Casting VC100 - page 30

    Unit won’t stay lit Wind Running out of fuel PROBLEM POTENTIAL CAUSE ACTION REQUIRED Burner will not light Gas supply turned off Out of propane Blockage in the gas system Misalignment of the gas valve to the venturi tubes of the burner . Improper attachment of the propane hose and regulator Control knob left open at startup or T urning gas on too ...

  • Vermont Casting VC100 - page 31

    PROBLEM POTENTIAL CAUSE ACTION REQUIRED Blockage in the burner or gas system Corroded burner Improper air shutter opening Excessively fatty foods Grease buildup Uneven burn pattern or Flashback fire Excessive yellow flame Flareup Electrode fouled Electrode improperly gapped Electrode cracked Lead wire is disconnected Lead wire is cracked Battery dr ...

  • Vermont Casting VC100 - page 32

    W arranty OUTDOOR PRODUCTS ◆ Lifetime W arranty • On all exterior Stainless Steel Components, such as the cart paneling & doors, shelving, condiment bins and handles. ◆ 10 Y ear W arranty • On all porcelain onsteel surfaces such as the shelving, hood and burn chamber . • On all manifold and valves, knobs plus the infrared rotisserie b ...

  • Vermont Casting VC100 - page 33

    CFM Corporation 2695 Meado wv ale Boulev ard Mississaug a, Ontario L5N 8A3 Canada (800) 668-5323 www .cfmcorp .com Service Note: If you are experiencing difficultie s or are dissatisfied with your purchase, please contact CFM at the telephone number listed above prior to returning your grill to the store. ...

Manufacturer Vermont Casting Category Griddle

Documents that we receive from a manufacturer of a Vermont Casting VC100 can be divided into several groups. They are, among others:
- Vermont Casting technical drawings
- VC100 manuals
- Vermont Casting product data sheets
- information booklets
- or energy labels Vermont Casting VC100
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vermont Casting VC100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vermont Casting VC100, service manual, brief instructions and user manuals Vermont Casting VC100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vermont Casting VC100.

A complete manual for the device Vermont Casting VC100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vermont Casting VC100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vermont Casting VC100.

A complete Vermont Casting manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vermont Casting VC100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vermont Casting VC100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vermont Casting VC100, that we can find in the current document
3. Tips how to use the basic functions of the device Vermont Casting VC100 - which should help us in our first steps of using Vermont Casting VC100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vermont Casting VC100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vermont Casting VC100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vermont Casting VC100?

Use the form below

If you did not solve your problem by using a manual Vermont Casting VC100, ask a question using the form below. If a user had a similar problem with Vermont Casting VC100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)