English dropdown-ico

Manual Opticon LGZ 7225

87 pages 0.81 mb
Download

Go to site of 87

Summary
  • Opticon LGZ 7225 - page 1

    User’s Manual LGZ 7225 Long Range Handheld CCD Scanner 25-ULGZMU01-01 Keyboard Wedge Interface USB Interface RS232 Interface 8 Olympic Drive Orangeburg, NY 10962 Tel 800.636.0090 Fax 845.365.1251 www.opticonUSA.com 1 ...

  • Opticon LGZ 7225 - page 2

    Content s General Information Unpacking . Opticon Customer Service and Support I n s t a l l a t i o n Default Settings Interface Selection Scanning Modes Beeper Settings Symbology Options Prefix/Suffix Strings Transmission Setting Parameter Settings List Programming Bar Codes 2 ...

  • Opticon LGZ 7225 - page 3

    Getting Started General Information The LGZ 7225 CCD Scanner utilizes state-of-the art imaging technology similar to that found in digital cameras, fax machines and video cam corders. The captures an “image” of the bar code and converts it into digital signals that the host computer understands. The scanner automatically recognizes mo st common ...

  • Opticon LGZ 7225 - page 4

    LGZ7225 Long Range Handheld CCD Spec 160 g (cable not included) Cable - K/B Wedge Straight 2.0 m Cable - universal type Straight 2.3 m Connector type RJ-45 phone jack connector Case material ABS plastic Cushion material Rubber Electrical Input Voltage 5 VDC r 0.25V Power - Operating 1275 mW Power - Standby 600 mW Current - Operating 255 mA @ 5VDC C ...

  • Opticon LGZ 7225 - page 5

    Default Setting for each barcode shown as below: Code Type Read Checksum Verifacation Checksum Transmission Code ID UPC-A X X X A UPC-E X X X E EAN-13 X X X F EAN-8 X X X FF Code-39 X * Interleaved 2of5 X X i Industrial 2of5 i Matrix 2of5 B Standard 2of5 i China Post t Codabar % Code-128 X X # Code-93 & Code-11 O MSI/Plessey @ UK/Plessey @ Tele ...

  • Opticon LGZ 7225 - page 6

    Programming Programming method Manual (Reading special barcode) DOS command through RS-232, Windows configuration program Program upgrade Enabled by built-in flash memory Programmable characteristics Code type selection, check digit selection Decoding option Decoding option T ransmitted character delay , Header selection, trailer selection, message ...

  • Opticon LGZ 7225 - page 7

    Programming t he LGZ7225 T o program the LGZ7225 you must scan a series of programming barcode in the correct order . Fold out the back cover of this manual. Y ou will see a table of alphanumeric barcodes, which are used to program the various options presented. T o program each option, you must: 1. Scan the Program barcode on the parameter setting ...

  • Opticon LGZ 7225 - page 8

    Option Bar Code Option Alphanumeric Entry Interface selection Keyboard W edge RS-232 Wand emulation USB Keyboard/RS-232 Auto detection reserved 00 ഖ 01 02 03 04 05 Back Fold Out Finish barcode Exit Barcode Option Barcode Program Barcode Exit Program 8 ...

  • Opticon LGZ 7225 - page 9

    Interface Selection This decoder buil t -in scanner comes in one model and supports interfaces such as keyboard wedge, RS232 serial wedge, wand emulation, and the latest USB interface. In most of the cases, simply s utilizing the an appropriate cable with a device code will work for a specific interface. Interface selection: Y ou can change factor ...

  • Opticon LGZ 7225 - page 10

    Keyboard wedge As a keyboard interface, the scanner supports most of the popular PCs and IBM terminals. The inst allation of the wedge is a fairly simple process without any changes of software or hardware. Keyboard T ype: Select keyb oard type connector of your host computer . Scanner must be selected to the appropriate host interface cable conver ...

  • Opticon LGZ 7225 - page 11

    Keyboard wedge Keyboard Layout : The selecting of keyboard layout supports many country languages other than USA keyboard layout. First you need to confirm country language that you desire. In DOS, using command “keyb” to select the desirable keyboard layout or in WINDOWS entry “Control” then pops “Keyboard” to select country at “lang ...

  • Opticon LGZ 7225 - page 12

    Keyboard layout USA Belgium Danish France Germ any Italian Portuguese S panish Swedish Switzerland UK Latin American 00 ഖ 01 02 03 04 05 06 07 08 09 10 11 Keyboard speed 0-8 0 : high clock rate 8 : low clock rate 00-08 01 ഖ  Function key Disable Enable 00 01 ഖ Numeric key Alphabetic key Numeric keypad (Num lock state only) Alt+Keypad 00 ? ...

  • Opticon LGZ 7225 - page 13

    Keyboard wedge Caps Lock: By selecting Caps Lock or No Caps Lock , scanner can get Caps Lock status. Power-on simulation: All of the PCs check the keyboard status during power-on selftest. It is recommended to Enable function if you are working without keyboard installation. It simulates keyboard timing and pass keyboard present status to the PC du ...

  • Opticon LGZ 7225 - page 14

    Program Option Bar Code Option Alphanumeric Entry Caps lock Caps lock”ON” Caps lock”OFF” 00 01 ഖ Power-on simulation Disable Enable 00 ഖ 01 Inter-character delay 00-99 msec 00-99 02 ഖ Block transmission delay 00-99 10 msec 00-99 10 ഖ Exit 14 ...

  • Opticon LGZ 7225 - page 15

    RS-232 CTS: Clear T o Send (Hardware Signal) RTS: Request T o Send (Hardware Signal) Xon: T ransmit On (ASCII Code 1 1 16 ) Xoff: T ransmit Off (ASCII Code13 16 ) Flow control: None- The communication only uses TxD and RxD signals without regard for any hardware o r software handshaking protocol. RTS/CTS- If the scanner wants to send the barcode da ...

  • Opticon LGZ 7225 - page 16

    Program Option Bar Code Option Alphanumeric Entry Flow control None RTS/ CT S Xon/Xoff ACK/NAK 00 ഖ 01 02 03 Inter-character delay 00-99 (msec) 00-99 00 ഖ Block transmission delay 00-99 (10 msec) 00-99 00 ഖ Response delay 00-99 (100 msec) 00-99 20 ഖ Exit 16 ...

  • Opticon LGZ 7225 - page 17

    Program Option Bar Code Option Alphanumeric Entry Baud rate 300 BPS 600 BPS 1200 BPS 2400 BPS 4800 BPS 9600 BPS 19200 BPS 38400 BPS 00 01 02 03 04 05 ഖ 06 07 Parity None Odd Even 00 ഖ 01 02 Data bit 8 bits 7 bits 00 ഖ 01 S top bit One bit T wo bits 00 ഖ 01 Exit 17 ...

  • Opticon LGZ 7225 - page 18

    W and Emulation Bar/space polarity: High/low - Black will be transmitted as a high voltage level (+5) and space as low level (0V). Low/high - Black will be transmitted as a low voltage level (0V) and space as high level (+5). Initial polarity: Y ou must make sure what is Initial polarity of your wand decode device in stand-by (idle). So, initial si ...

  • Opticon LGZ 7225 - page 19

    W and Emulation Output speed: This setting is same as serial transmission baud rate, and it must be approbated your wand decode resolution. The unit of speed is a width of minimum narrow bar . Margin delay: It is a timer of zone like space zone of barcode label margin. The width of margin time will be added before and after in each barcode data aut ...

  • Opticon LGZ 7225 - page 20

    Reserved 00 ഖ Reserved 00 ഖ Margin delay 00-99 (10 pixel) 00-99 15 ഖ T ransmit delay 00-99 (10 msec) 00-99 30 ഖ Exit 20 ...

  • Opticon LGZ 7225 - page 21

    Scan Scanning mode: Good-read off- The trigger button must be pressed to activate scanning. The light source of scanner stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed. Momentary- The trigger button acts as a switch. Press button to activate scanning and release button to stop scanning. Al ...

  • Opticon LGZ 7225 - page 22

    Program Option Bar Code Option Alphanumeric Entry Scanning mode Good-read off Momentary Alternate T imeout off Continue 00 01 ഖ 02 03 04 S tand-by duration 01-99 (second) 00-99 10 ഖ Same barcode delay time 01-99 (10 msec) 01-99 50 ഖ Double confirm 00-99 (00: no double confirm) 00-09 00 ഖ Exit 22 ...

  • Opticon LGZ 7225 - page 23

    Scan Multi field scan: The scanner can be read m any sets of barcode data on the same scanning line at the same time, even if they are different kinds of barcode symbology . Global min./max. code length: Global Minimum and Maximum length can be set to qualify data entry . The length is defined as the actual barcode data length to be sent. Label wit ...

  • Opticon LGZ 7225 - page 24

    Multi field scan Disable Enable 00 ഖ 01 Global min. code length 00-63 00-63 04 ഖ Global max.code length 00-63 04-63 63 ഖ Inverted image scan Disable Enable 00 ഖ 01 CTS trigger Disable Enable 00 ഖ 01 Position indication Disable 30 second 60 second 90 second 120 second 150 second 180 second Continue 00 ഖ 01 02 03 04 05 06 07 Exit 24 ...

  • Opticon LGZ 7225 - page 25

    Indication Exit Power on alert: After power-on the scanner it will generate an alert signal to indicate a successful self-test. LED indication: After each successful reading, the LED above the scanner will light up to indicate a good barcode reading. Buzzer indication: After each successful reading, the scanner will beep buzzer to indicate a good b ...

  • Opticon LGZ 7225 - page 26

    Program Option Bar Code Option Alphanumeric Entry Power on alert Disable Enable 00 01 ഖ LED indication Disable Enable 00 01 ഖ Buzzer indication Disable Enable 00 01 ഖ Beep loudness 00-07 00-07 07 ഖ Beep tone freq. 00-99 (100Hz) 00-99 2 6 ഖ Beep tone duration 00-99 (10 msec) 00-99 10 ഖ Exit 26 ...

  • Opticon LGZ 7225 - page 27

    UPCA Read: Format Leading Zero Data Digits (1 1 Digits) Check Digit Check-sum transmissi on: By setting Enable , checks sum will be transmitted. T runcate leading/ending: The leading or ending digits of barcode data characters can be truncated when these values are set to non-zero. It will beep instead of reading anything when the truncate value is ...

  • Opticon LGZ 7225 - page 28

    Check-sum verification Disable Enable 00 01 ഖ Check-sum transmission Disable Enable 00 01 ഖ Max.code length 00-64 00-64 64 ഖ Min.code length 00-64 00-64 01 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < A > ഖ Insert group selection 00-44 00-44 0 0 ഖ Exit 28 ...

  • Opticon LGZ 7225 - page 29

    UPCA  Supplement dig its: The Supplement digits barcode is the supplemental 2 or 5 characters for WPC code. Format Leading Zero Data Digits (1 1 Digits) Check Digit Supplement Digits 2 or 5 or UCC / EAN 128 T runcate Leading zero: The leading “0” digits of UPCA dat a characters can be truncated when the function is enabled.    Progr ...

  • Opticon LGZ 7225 - page 30

    UPCE  Read: Format Leading Zero Data Digits (6 Digits) Check Digits Check-sum verification: The checksum of EAN-13 is optional and made as the sum of the numerical value of the data digits. Check-sum transmissi on: By setting Enable , checks sum will be transmitted.  Program Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01 ...

  • Opticon LGZ 7225 - page 31

    UPCE  T runcate leading/ending: Refer to T runcate leading/ending of UPCA. Code Id setting: Refer to Code I D setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Supplement digits: Format Leading Zero Data Digits (6 Digits) Check Digit Supplement Digits 2 or 5 or UCC/EAN 128 T runcate Leading zero: Refer to T ...

  • Opticon LGZ 7225 - page 32

    T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < E > ഖ Insert group selection 00-44 00-44 00 ഖ Supplement digits None 2 digits 5 digits UCC/EAN 128 Auto detection 00 ഖ 01 02 03 04 T runcate Leading zero Disable Enable 00 ഖ 01 Expansion Disable Enable 00 ഖ 01    Exit   32 ...

  • Opticon LGZ 7225 - page 33

    EAN-13  Read: Format Data Digits (12 Digit s) Check Digits Check-sum verification: The checksum of EAN-13 is optional and made as the sum of the numerical value of the data digits. Check-sum transmissi on: By setting Enable , checks sum will be transmitted. Max./Min. code length: Each symbology has own Max./Min. Code Length. They can be set to q ...

  • Opticon LGZ 7225 - page 34

    Check-sum verification Disable Enable 00 01 ഖ Check-sum transmission Disable Enable 00 01 ഖ Max.code length 00-64 00-64 64 ഖ Min.code length 00-64 00-64 01 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ  Exit 34 ...

  • Opticon LGZ 7225 - page 35

    EAN-13 Code Id setting: Refer to Code I D setting of UPCA. Insertion group selecti on: Refer to Insertion group selection of UPCA. Supplement dig its: Format Data Digit s (12 Digits) Check Digits Supplement Digits 2 or 5 or UCC / EAN 128 ISBN/ISSN: The ISBN (International St andard Book Number) and ISSN (International St andard Serial Number) are t ...

  • Opticon LGZ 7225 - page 36

    Program Option Bar Code Option Alphanumeric Entry Code ID setting 00-ffH ASCII code 00-ffH < F > ഖ Insert group selection 00-44 00-44 00 ഖ Supplement digits None 2 digits 5 digits UCC/EAN 128 Auto detection 00 ഖ 01 02 03 04 ISBN/ISSN conversion Disable Enable 00 ഖ 01 Exit 36 ...

  • Opticon LGZ 7225 - page 37

    EAN-8  Read: Format Data Digits (7 Digits) Check Digits Check-sum verification: The checksum of EAN-8 is optional and made as the sum of the numerical value of the data digits. Check-sum transmissi on: By setting Enable , checks sum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of EAN-13. T runcate leading/ending: Re ...

  • Opticon LGZ 7225 - page 38

    Check-sum transmission Disable Enable 00 01 ഖ Max.code length 00-64 00-64 64 ഖ Min.code length 00-64 00-64 01 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting T wo characters 00-ffH ASCII code 00-ffH, 00-ffH < FF > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 38 ...

  • Opticon LGZ 7225 - page 39

    EAN-8 Supplement dig its: Format Data Digits (7 Digits) Check Digits Supplement Digits 2 or 5 or UCC/EAN 128 T runcate Leading zero: Refer to T runcate Leading zero of UPCE. Exp ansion: Refer to Expansion of UPCE. Program Option Bar Code Option Alphanumeric Entry Supplement digits None 2 digits 5 digits UCC/EAN 128 Auto detection 00 ഖ 01 02 03 04 ...

  • Opticon LGZ 7225 - page 40

    Code 39 Read: Format Sta rt “ ့ ” Data Digits ( V ariable) Checksum (Optional) End “ ့ ” Check-sum verification: The checksum of Code-39 is optional and made as the sum module 43 of the numerical value of the data digits. Check-sum transmissi on: By setting Enable , checksum and will be transmitted.    Option Bar Code Option Al ...

  • Opticon LGZ 7225 - page 41

    Code 39  Max./Min. code length: Each symbology has own Max./Min. Code Length. They can be set to qualify data entry . If their Max./Min. Code Length is zero, the Global Min./Max. Code Length is in effect. The length is defined as to the actual barcode data length to be sent. Label with length exceeds these limits will b e rejected. Make sure tha ...

  • Opticon LGZ 7225 - page 42

    Max. code length 00-64 00-64 00 ഖ Min. code length 00-64 00-64 00 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < ഖ > Insert group selection 00-44 00-44 00 ഖ Format S tandard Full ASCII 00 ഖ 01 Exit 42 ...

  • Opticon LGZ 7225 - page 43

    Code 39  Append: This function allows several symbols to be concatenates and be treat as one single data entry . The scanner will not transmit the embedded appending code (space for Code-39). If Enable and other symbols were read again with the appended code, then codes will be transmitted without Code ID, Preamble and Prefix. When a symbol was ...

  • Opticon LGZ 7225 - page 44

    Interleaved 2 of 5 Read: Format Data Digits (V ariable) Checksum (Optional) Check-sum verification: The checksum is made as the sum module 10 of the numerical values of all data digits. Check-sum transmissi on: By setting Enable , checksum and will be transmitted. Program Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01 ഖ Check ...

  • Opticon LGZ 7225 - page 45

    Interleaved 2 of 5 Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/ending: Refer to T runcate leading/ending of UPCA. Code Id setting: Refer to Code I D setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option Bar Code Option Alphanumeric Entry Max. code leading 00-64 ...

  • Opticon LGZ 7225 - page 46

    Code ID setting 00-ffH ASCII code 00-ffH < i > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 46 ...

  • Opticon LGZ 7225 - page 47

    Industrial 2 of 5 Read: Format Data Digits (V ariable) Checksum (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/ending: Refer to T runcate leading/ending of UPCA. Code Id setting: Refer to Code I D setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option Ba ...

  • Opticon LGZ 7225 - page 48

    T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < i > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 48 ...

  • Opticon LGZ 7225 - page 49

    Matrix 2 of 5 Eur  Read: Format Data Digits (V ariable) Checksum (Optional) Checksum V erification: The checksum is made as the sum module 10 of the numerical values of all data digits. Checksum T ransmission: By setting Enable , checksum and will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading ...

  • Opticon LGZ 7225 - page 50

    Checksum T ransmission Disable Enable 00 ഖ 01  Max. code length 00-64 00-64 00 ഖ  Min. code length 00-64 00-64 00 ഖ  T runcate leading 0-15 00-15 00 ഖ  T runcate ending 0-15 00-15 00 ഖ  Code ID setting 00-ffH ASCII code 00-ffH < B > ഖ Insert group selection 00-44 00- 44 00 ഖ Exit 50 ...

  • Opticon LGZ 7225 - page 51

    Codabar Read: Format S tart Data Digits (V ariable) Checksum (Optional) End Checksum V erification: The checksum is made as the sum module 16 of the numerical values of all data digits. Checksum T ransmission: By setting Enable , checksum and will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/en ...

  • Opticon LGZ 7225 - page 52

    Checksum T ransmission Disable Enable 00 ഖ 01 Max. code length 00-64 00-64 00 ഖ Min. code length 00-64 00-64 00 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < % > ഖ Exit 52 ...

  • Opticon LGZ 7225 - page 53

    Codabar Insertion group selection: Refer to Insertion group selection of UPCA. St art /End type : The Codabar has four pairs of St art/End pattern; you may select one pair to match your application. St art/End T ransmission: Refer to St art/End T ransmission of Code 39. Program Option B ar Code Option Alphan umeric Entry Insert group selection 00-4 ...

  • Opticon LGZ 7225 - page 54

    Code-128 Read: Format Data Digits (V ariable) Checksum (Optional) Checksum V erification: The checksum is made as the sum module 103 of all data digits. Checksum T ransmission: By setting Enable , checksum and will be transmitted. Program Option B ar Code Option Alphan umeric Entry Read Disable Enable 00 01 ഖ Checksum V erification Disable Enable ...

  • Opticon LGZ 7225 - page 55

    Code-128 Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/ending: Refer to T runcate leading/ending of UPCA. Code Id setting: Refer to Code I D setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Format: The Code-128 can be tr anslated to UCC/ EAN-128 format if it starts with FN ...

  • Opticon LGZ 7225 - page 56

    T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < # > ഖ Insert group selection 00-44 00-44 00 ഖ Format S tandard UCC/EAN-128 00 ഖ 01 Append Disable Enable 00 ഖ 01 UCC/EAN-128 ID setting 00-ffH ASCII code 00-ffH < # > ഖ Field separator code 00-ffH ASCII code 1DH ? ...

  • Opticon LGZ 7225 - page 57

    Code-93 Read: Format Data Digits (V ariable) Checksum1 (Optional) Checksum2 (Optional) Checksum V erification: The checksum is made as the sum module 47 of the numerical values of all data digits. Checksum T ransmission: By setting Enable , checksum and will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate ...

  • Opticon LGZ 7225 - page 58

    Checksum T ransmission Disable Enable 00 ഖ 01 Max. code length 00-64 00-64 00 ഖ Min. code length 00-64 00-64 00 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < & > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 58 ...

  • Opticon LGZ 7225 - page 59

    Code-1 1 Read: Format Data Digits (V ariable) Checksum1 (Optional) Checksum2 (Optional) Checksum V erification: The checksum is presented as the sum module 1 1 of all data digits. Checksum T ransmission: By setting Enable , checksum1 and checksum2 will be transmitted upon your selected checksum verification method. Max./Min. code length: Refer to M ...

  • Opticon LGZ 7225 - page 60

    Checksum T ransmission Disable Enable 00 ഖ 01 Max. code length 00-64 00-64 00 ഖ Min. code length 00-64 00-64 00 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < O > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 60 ...

  • Opticon LGZ 7225 - page 61

    MSI/plessey Read: Format Data Digits (V ariable) Checksum1 (Optional) Checksum2 (Optional) Checksum V erification: The MSI/Plessey has one or two optional checksum digits. The checksum is presented 3 kinds of method Mod10 , Mod10/10 and Mod 1 1/10 . The checksum1 and checksum2 will be calculated as the sum module 10 or 1 1 of the dat a digits. Chec ...

  • Opticon LGZ 7225 - page 62

    Checksum T ransmission Disable Enable 00 ഖ 01 Max. code length 00-64 00-64 00 ഖ Min. code length 00-64 00-64 00 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < @ > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 62 ...

  • Opticon LGZ 7225 - page 63

    UK/plessey Read: Format Data Digits (V ariable) Checksum1+2 (Optional) Checksum V erification: The UK/Plessey has one or two optional checksum digits. The checksum1 and checksum2 will be calculated as the sum module 10 or 1 1 of the data digits. Checksum T ransmission: By setting Enable , checksum will be transmitted. Max./Min. code length: Refer t ...

  • Opticon LGZ 7225 - page 64

    Checksum T ransmission Disable Enable 00 ഖ 01 Max. code length 00-64 00-64 00 ഖ Min. code length 00-64 00-64 00 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < @ > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 64 ...

  • Opticon LGZ 7225 - page 65

    T elepen Read: IA T A (International Air Transport Association). Checksum V erification: The checksum is presented as the sum module 10 or 1 1 of the data digits. Checksum T ransmission: By setting Enable , checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/ending: Refer to T runcate le ...

  • Opticon LGZ 7225 - page 66

    Max. code length 00-64 00-64 00 ഖ Min. code length 00-64 00-64 00 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < S > ഖ Insert group selection 00-44 00-44 00 ഖ )RUPDW 1XPHULFRQO )XOO$6&,,RQO  ഖ      Exit 66 ...

  • Opticon LGZ 7225 - page 67

    St andard 2 of 5 Read: Format Data Digits (V ariable) Checksum1 (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/ending: Refer to T runcate leading/ending of UPCA. Code Id setting: Refer to Code I D setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option B ...

  • Opticon LGZ 7225 - page 68

    T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < i > ഖ Insert group selection 00-44 00-44 00 ഖ Exit 68 ...

  • Opticon LGZ 7225 - page 69

    China Post Read: Format Data Digits (V ariable) Checksum1 (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/ending: Refer to T runcate leading/ending of UPCA. Code Id setting: Refer to Code I D setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Program Option B ar Cod ...

  • Opticon LGZ 7225 - page 70

    T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 00-ffH < t > ഖ Insert group selection 00-44 01-44 00 ഖ Exit 70 ...

  • Opticon LGZ 7225 - page 71

    It alian Pharmacode Read: Format Data Digits (V ariable) Checksum1 (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. T runcate leading/ending: Refer to T runcate leading/ending of UPCA. Code Id setting: Refer to Code I D setting of UPCA. Insertion group selection: Refer to Insertion group selection of UPCA. Leading “A? ...

  • Opticon LGZ 7225 - page 72

    Min. code length 00-64 00-64 09 ഖ T runcate leading 0-15 00-15 00 ഖ T runcate ending 0-15 00-15 00 ഖ Code ID setting 00-ffH ASCII code 01-ffH < p > ഖ Insert group selection 00-44 00-44 00 ഖ Leading “A” Disable Enable 00 ഖ 01 Exit 72 ...

  • Opticon LGZ 7225 - page 73

    String setting Prefix characters : Up to 22 ASCII characters may be sent before data digits. Pre fi x Data D ig its Suffi x Suffix characters: Up to 22 ASCII characters may be sent after data digit s. Preamble/ Postamble characters: They are appended to the data automatically when each barcode is decoded. Example: Add a prefix/suffix or preamble/po ...

  • Opticon LGZ 7225 - page 74

    Preamble characters setting None 1-22 characters 00 ഖ 00-ffH ASCII code Postamble characters setting None 1-22 characters 00 ഖ 00-ffH ASCII code Insert G1 characters setting None 1-22 characters 00 ഖ 00-ffH ASCII code Insert G2 characters setting None 1-22 characters 00 ഖ 00-ffH ASCII code Insert G3 characters setting None 1-22 characters 0 ...

  • Opticon LGZ 7225 - page 75

    String setting Insert G1/G2/G3/G4 character settin g: The scanner offer 4 positions and 4 characters to insert among the symbol. Example: Barcode “1 2 3 4 5 6”. Output- Barcode “1 2 A B 3 4 C D 5 6”. St e p s : 1) Scan Prog ramming and Insert G1 characters setting barcode. 2) Use the ASCII code t able to find the value of A ඎ 41,B ඎ 42. ...

  • Opticon LGZ 7225 - page 76

    Insert G3 characters setting None 1-22 characters 00 ഖ 00-ffH ASCII code Insert G4 characters setting None 1-22 characters 00 ഖ 00-ffH ASCII code Exit 76 ...

  • Opticon LGZ 7225 - page 77

    T ransmission Preamble transmission : By setting Enable , Preamble will be appended before the data transmitted. Postamble transmission: By setting Enable, Postamble will be appended after the data is transmitted. Insert data group 1-4 position: The scanner offers 4 positions to insert among the symbol. The position default value is “00” to ind ...

  • Opticon LGZ 7225 - page 78

    Insert data group 1 position 00-64 (00: no insertion) 00-64 00 ഖ Insert data group 2 position 00-64 (00: no insertion) 00-64 00 ഖ Insert data group 3 position 00-64 (00: no insertion) 00-64 00 ഖ Insert data group 4 position 00-64 (00: no insertion) 00-64 00 ഖ Code ID position Before code data After code data 00 ഖ 01 Exit 78 ...

  • Opticon LGZ 7225 - page 79

    T ransmission Code ID transmission: If your a pplication is needed to transmit Code ID, you must set this to Proprietary ID or AIM ID. Code length transmiss ion: A number of data digit s can be transmitted before the code data when Enable is selected. The total length of the barcode is the number of barcode data except T runcate Leading/Ending Digi ...

  • Opticon LGZ 7225 - page 80

    Code length transmission Disable Enable 00 ഖ 01 Code name transmission Disable Enable 00 ഖ 01 Case conversion Disable Upper case Lower case *For barcode data only 00 ഖ 01 02 Exit Format of barcode da ta transmission: Prefix Name Preamble ID Code Length Barcode data ID Postamble Suf fix Insert groups 80 ...

  • Opticon LGZ 7225 - page 81

    7HVW&KDUW CODABAR-P ARA CODE-1 1 P ARA CODE-128 P ARA CODE-39 P ARA CODE-93 P ARA EAN-13 P ARA  81 ...

  • Opticon LGZ 7225 - page 82

    PDF-417 ST ANDR AD-25 P ARA CODE-16K EAN-8 P ARA INDUSTRIAL-25 P AR A UPCE P ARA  82 ...

  • Opticon LGZ 7225 - page 83

    INTERLEA VED-25 P ARA MA TRIX 25 P ARA  MSI/PLESSEY P ARA UPCA P ARA UK/PLESSEY P ARA   83 ...

  • Opticon LGZ 7225 - page 84

       ASCII Code T able 1RWH )RUNHERDUGZHGJH RQO / +       1XOO  18/ '/(  8S ) 62+ '&  'RZQ ) 67; '&  /HIW ) (7; '&  5LJKW ) (27 &apos ...

  • Opticon LGZ 7225 - page 85

    Parameter Setting List Program Barcode standard p arameter setting list If you wish to display the current configuration of your LGZ7225 , scanner over the host terminal/computer scan the Barcode standard parameter setting list bar code. Unique parameter list If you wish to display the unique parameter setting list, scan the unique parameter list b ...

  • Opticon LGZ 7225 - page 86

    Firmware version list If you wish to display the firmware version, scan the Firmware version list. WA RNING : Default value initiali zation If you wish to return the LGZ 7225 to all the factory default settings, scan the Default value initialization bar code. Exit 86 ...

  • Opticon LGZ 7225 - page 87

    97 0 A 1 B 2 C 3 D 4 E 5 F 6 7 8 Finish 9 87 ...

Manufacturer Opticon Category Scanner

Documents that we receive from a manufacturer of a Opticon LGZ 7225 can be divided into several groups. They are, among others:
- Opticon technical drawings
- LGZ 7225 manuals
- Opticon product data sheets
- information booklets
- or energy labels Opticon LGZ 7225
All of them are important, but the most important information from the point of view of use of the device are in the user manual Opticon LGZ 7225.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Opticon LGZ 7225, service manual, brief instructions and user manuals Opticon LGZ 7225. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Opticon LGZ 7225.

Similar manuals

A complete manual for the device Opticon LGZ 7225, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Opticon LGZ 7225 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Opticon LGZ 7225.

A complete Opticon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Opticon LGZ 7225 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Opticon LGZ 7225, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Opticon LGZ 7225, that we can find in the current document
3. Tips how to use the basic functions of the device Opticon LGZ 7225 - which should help us in our first steps of using Opticon LGZ 7225
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Opticon LGZ 7225
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Opticon LGZ 7225 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Opticon LGZ 7225?

Use the form below

If you did not solve your problem by using a manual Opticon LGZ 7225, ask a question using the form below. If a user had a similar problem with Opticon LGZ 7225 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)