English dropdown-ico

Manual Wegener Communications DVR396

30 pages 0.26 mb
Download

Go to site of 30

Summary
  • Wegener Communications DVR396 - page 1

    Inst allation Guide Model DVR395/DVR396 DIGIT AL VIDEO RECEIVER Data, drawings, and other material contained herein are proprietary to Wegener Communications, Inc., and may not be reproduced or duplicated in any form without the prior permission of Wegener Communications, Inc. When ordering parts from Wegener Communications, Inc., be sure to includ ...

  • Wegener Communications DVR396 - page 2

    Page 2 DVR395/DVR396-002 Page 2 of 30 This Page Intentionally Left Blank ...

  • Wegener Communications DVR396 - page 3

    Page 3 Page 3 of 30 DVR395/DVR396-002 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION As this unit is intended to interface with other electrical/electronic systems, proper engineering pr ...

  • Wegener Communications DVR396 - page 4

    Page 4 DVR395/DVR396-002 Page 4 of 30 This Page Intentionally Left Blank ...

  • Wegener Communications DVR396 - page 5

    Page 5 Page 5 of 30 DVR395/DVR396-002 ABOUT THIS MANUAL This manual was composed in Microsoft W ord 97, and is configured to be used most easily as an electronic document. It can be printed and used as a hard copy, but some features, such as links, are not accessible in that mode. If viewing the electronic version, we recommend you safeguard the or ...

  • Wegener Communications DVR396 - page 6

    Page 6 DVR395/DVR396-002 Page 6 of 30 This Page Intentionally Left Blank ...

  • Wegener Communications DVR396 - page 7

    Page 7 Page 7 of 30 DVR395/DVR396-002 T ABLE OF CONTENTS ABOUT THIS MANUAL ............................................................................................................. 5 TABLE OF CONTENTS ............................................................................................................. 7 LIST OF ILLUSTRATIONS ........... ...

  • Wegener Communications DVR396 - page 8

    Page 8 DVR395/DVR396-002 Page 8 of 30 LIST OF ILLUSTRA TIONS Figure 1. Ferrite Bead Installation For DVR396 ......................................................................... 11 Figure 2. DVR395 Rear Panel ..................................................................................................... 13 Figure 3. DVR396 Rear Panel .... ...

  • Wegener Communications DVR396 - page 9

    Page 9 Page 9 of 30 DVR395/DVR396-002 SECTION 1 GENERAL INFORMA TION 1.1 INTRODUCTION This section contains instructions for c onnecting the Model DVR395/DVR396 Digital Video Receiver into a satellite receive system , and operating it in that mode. 1.2 UNP ACKING AND INSPECTION Carefully unpack the unit and inspect it for obvi ous signs of physical ...

  • Wegener Communications DVR396 - page 10

    Page 10 DVR395/DVR396-002 Page 10 of 30 required if the room is cool (<75°F). For hi gher rack mounting densities, forced-air rack ventilation is strongly recommended. Please no te the average per-unit power dissipation of 45 watts (@ max LNB DC current loading) and plan accord ingly. Table 1. Equipment Specifications Parameter Specification In ...

  • Wegener Communications DVR396 - page 11

    Page 11 Page 11 of 30 DVR395/DVR396-002 1.4 REAR P ANEL CONNECTIONS The DVR395 rear panel connections are shown and described in Figure 2 (Page13). Figure 1. Ferrite Bead Installation For DVR396 1.4.1 Ferrite Cores And Their Installation In order to meet FCC requirement s for Radiated Emissions, this unit m ust have Ferrites installed on certain ca ...

  • Wegener Communications DVR396 - page 12

    Page 12 DVR395/DVR396-002 Page 12 of 30 installations, but especially in multi-service environm ents, should use high-quality shielded cables, with the shield grounded according to good engineering standard s. 1.4.1.2 Ferrite Installation For this installation, there are three ferrites that are larger than the others. These should be used for the c ...

  • Wegener Communications DVR396 - page 13

    Page 13 Page 13 of 30 DVR395/DVR396-002 Figure 2. DVR395 Rear Panel Figure 3. DVR396 Rear Panel MODULE 1 RS232 CONTACT RATING 0.1A @ 30VDC AUDIO R RF IN R LL 16 2 1 AUDIO MODE PORT SERIAL HSD OUT S/N CH 2/3 MOD OUT OUT MODULE 2 (MODULE 2) (MODULE 1) VIDEO - CLOSURE GND ALARM N/O COM 1 + N/C 2 - + AUDIO 4 6 S-VIDEO AUDIO 3 5 115/230VAC RISQUE DE CHO ...

  • Wegener Communications DVR396 - page 14

    Page 14 DVR395/DVR396-002 Page 14 of 30 1.5 SECURITY LABELS The DVR395 incorporates security labels. There are no user serviceable components within the IRD (integrated receiver decoder). Ta mpering with the security labels, opening the units, will void your warranty. If you have questions, contact Wegener's custom er service department at the ...

  • Wegener Communications DVR396 - page 15

    Page 15 Page 15 of 30 DVR395/DVR396-002 VIDEO CONNECTIONS Composite: connect the composite video output to the desired unit using a standard phono plug cable. The equipment it is connected to MUST have a 75-ohm term ination. S-video: connect the S-video output to the desired unit using a standard S-video mini- DIN connector. AUDIO CONNECTIONS Using ...

  • Wegener Communications DVR396 - page 16

    Page 16 DVR395/DVR396-002 Page 16 of 30 1.6 TECHNICAL SUPPORT In the event the unit fails to perform as desc ribed, contact Wegener Communications Customer Service at (770) 814-4057, F AX (770) 232-0621, or email “ service@wegener.com ”. To return a product for service: 1. Obtain a Return Material Authorization (RMA) number by com pleting and f ...

  • Wegener Communications DVR396 - page 17

    Page 17 Page 17 of 30 DVR395/DVR396-002 SECTION 2 POWER ON PROCEDURES 2.1 GENERAL This section provides information and procedures for powering up the unit. 2.2 CONTROL DIP SWITCHES A four position DIP switch on the rear panel prov ides manual control and setup selection. Mode setting is as follows: (In se tting the DIP switches, "D" = do ...

  • Wegener Communications DVR396 - page 18

    Page 18 DVR395/DVR396-002 Page 18 of 30 Figure 4. DVR395 Front Panel Figure 5. DVR396 Front Panel MODEL DVR395 S/N STATUS SELECT ENTER MPEG-2 IRD COMMUNICATIONS WEGENER STATUS S/N MODEL DVR396 WEGENER COMMUNICATIO NS ENTER SELECT MPEG-2 IRD ...

  • Wegener Communications DVR396 - page 19

    Page 19 Page 19 of 30 DVR395/DVR396-002 Table 5. Front Panel Controls and Indicator Item Description IRD Status A Red/Green/Amber LED used to show operating status, including normal operation, warnings, and alarms. See Table 6 (Page 20). On Screen Display (OSD) On Screen Display of IRD may be activated by pressing the <SELECT> front panel pus ...

  • Wegener Communications DVR396 - page 20

    Page 20 DVR395/DVR396-002 Page 20 of 30 Table 6. LED Indications Mode Condition Status LED Power Up IRD is in process of powering up RED/GREEN Blink Pattern Boot Fail EEPROM Boot Failure RED Receiver Board Diagnostics Failure RED Receiver Board Communications Failure RED Secure micro / Host ID mism atch RED Alarm Receiver Board Run-Time Fa ilure RE ...

  • Wegener Communications DVR396 - page 21

    Page 21 Page 21 of 30 DVR395/DVR396-002 The following definitions apply to Table 6 : Blink - LED is OFF for 1 second, and then blinks on count times (ON for 250 m s and OFF for 250 ms). This overall pattern is continued. Flutter - ON for 50 ms, OFF for 50 ms, repeating…. AMBER - RED and GREEN turned ON at the same time. Note: ms = 1/1000 second T ...

  • Wegener Communications DVR396 - page 22

    Page 22 DVR395/DVR396-002 Page 22 of 30 This Page Intentionally Left Blank ...

  • Wegener Communications DVR396 - page 23

    Page 23 Page 23 of 30 DVR395/DVR396-002 SECTION 3 SETUP 3.1 GENERAL This section provides procedures for initial setup of the unit. 3.2 ON SCREEN DISPLA Y (OSD) The OSD information is contained in the video output from the receiver. It is turned on by pressing either the <SELECT> or <ENTER> push-button on the front panel. The display is ...

  • Wegener Communications DVR396 - page 24

    Page 24 DVR395/DVR396-002 Page 24 of 30 3.3 CUST OMIZING SETTINGS FO R YOUR SYSTEM You can customize the settings of the DVR395 to fit your system using the OSD and front panel push buttons. To edit settings, perform the following procedures and see Table 7 (Page 23). • Power up the unit. • Connect a terminal for the On Screen Display. See Sect ...

  • Wegener Communications DVR396 - page 25

    Page 25 Page 25 of 30 DVR395/DVR396-002 For Carrier Status: • From the Main Menu, select “Carrier Status.” • Press <ENTER> to display the “Carrier Status” screen. • This is a read-only screen. • Press <ENTER> to Return to the Main Menu. For Signal Strength: • From the Main Menu, select “Signal Strength” and Press & ...

  • Wegener Communications DVR396 - page 26

    Page 26 DVR395/DVR396-002 Page 26 of 30 For Software Version: This is a read-only screen showing the versions of the various software packages. • Select “Software Version” from the Main Menu and press <ENTER> to display the screen. • Press <ENTER> to return to the Main Menu. SOFTWARE SELECT Application: V1.3 Receiver: 17 (Type 4 ...

  • Wegener Communications DVR396 - page 27

    Page 27 Page 27 of 30 DVR395/DVR396-002 APPENDIX A RMA REQUEST FORM Not every system or location will use the RMA Re quest Form shown on the following page. It is provided as a convenience for those custom ers who send units directly to Wegener Communications, Inc. for repair. If there is any doubt regarding use of this form, contact Ne twork Contr ...

  • Wegener Communications DVR396 - page 28

    Page 28 DVR395/DVR396-002 Page 28 of 30 service@wegener.com RMA REQUEST FORM Fax (770) 232-0621 Com p an y Name: Bill-To Address: Shi p -To Address: Contact Name: Phone # ( ) - Fax #: ( ) - Com p lete Model #: Serial #: In Warrant y : Yes No Problem: Additional Comments: ...

  • Wegener Communications DVR396 - page 29

    Page 29 Page 29 of 30 DVR395/DVR396-002 RECORD OF REVISIONS Date of Change Rev. Level Page No. Description of Change 7/19/97 A Initial Release 8/27/99 B 10 11 Changed “RJ-11” to “RJ-12.” Table 3 , Reversed Ch. 2 & 3 in “Function” Column. 4/7/00 C 10 10 11 Added Sections 1.3.3 – 1.3.7 Added Metric equivalent measurements Added Ferr ...

  • Wegener Communications DVR396 - page 30

    Page 30 DVR395/DVR396-002 Page 30 of 30 SERVICE RETURN ADDRESS Service Department RMA# ________ Wegener Communications, Inc. 359 Curie Drive Alpharetta, GA 30005 CONTACT NUMBERS AND ADDRESSES Voice: (770) 814-4057 FAX: (770) 232-0621 email: service@wegener.com ...

Manufacturer Wegener Communications Category Stereo Receiver

Documents that we receive from a manufacturer of a Wegener Communications DVR396 can be divided into several groups. They are, among others:
- Wegener Communications technical drawings
- DVR396 manuals
- Wegener Communications product data sheets
- information booklets
- or energy labels Wegener Communications DVR396
All of them are important, but the most important information from the point of view of use of the device are in the user manual Wegener Communications DVR396.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Wegener Communications DVR396, service manual, brief instructions and user manuals Wegener Communications DVR396. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Wegener Communications DVR396.

Similar manuals

A complete manual for the device Wegener Communications DVR396, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Wegener Communications DVR396 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Wegener Communications DVR396.

A complete Wegener Communications manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Wegener Communications DVR396 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Wegener Communications DVR396, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Wegener Communications DVR396, that we can find in the current document
3. Tips how to use the basic functions of the device Wegener Communications DVR396 - which should help us in our first steps of using Wegener Communications DVR396
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Wegener Communications DVR396
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Wegener Communications DVR396 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Wegener Communications DVR396?

Use the form below

If you did not solve your problem by using a manual Wegener Communications DVR396, ask a question using the form below. If a user had a similar problem with Wegener Communications DVR396 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)