English dropdown-ico

Manual Roland PCR-800

100 pages 6.6 mb
Download

Go to site of 100

Summary
  • Roland PCR-800 - page 1

    04348534 1MP Owner’ s Manual Owner’s Manual Cover_e.fm 1 ページ ２００６年１２月１９日　火曜日　午後５時２３分 ...

  • Roland PCR-800 - page 2

    2 Contents Names of things and what they do ................ 4 Panel .................................................................................................. 4 Side panel ........................................................................................... 7 Using control maps ........................................ 8 What is a con ...

  • Roland PCR-800 - page 3

    3 Settings (Edit mode) ...................................... 41 Assigning MIDI messages on the PCR keyboard ..................................... 41 Note assign............................................................................ 42 Aftertouch assign .................................................................... 44 Control change assi ...

  • Roland PCR-800 - page 4

    4 Names of things and what they do fig.Panel-Left.eps Display This shows a variety of information, such as the current state. * The display will dim if you leave the PCR without operating it for several seconds. * The explanations in this manual include illustrations that depict what should typically be shown by the display. Note, however, that you ...

  • Roland PCR-800 - page 5

    5 Names of things and what they do VALUE knob By turning the VALUE knob you can change the value of the MIDI CHANNEL, PROGRAM CHANGE, CONTROL MAP, or USER. In Edit mode, use this knob to select the item that you want to edit. [MIDI CHANNEL] button After pressing the [MIDI CHANNEL] button so it’s lit, you can turn the VALUE knob to specify the cha ...

  • Roland PCR-800 - page 6

    6 Names of things and what they do fig.Panel-Top.eps Controllers [R1]–[R9] (knobs) You can assign the desired MIDI messages to these knobs. (-> Assigning a MIDI message (p. 20)) Controllers [A1]–[A9], [B1]–[B9] (pads) You can assign the desired MIDI messages to these pads. (-> Assigning a MIDI message (p. 20)) The force with which you p ...

  • Roland PCR-800 - page 7

    7 Names of things and what they do fig.Panel-Side.eps DC IN jack You can connect a separately available AC adaptor (p. 92) to this jack. If you wish to purchase an AC adaptor, please contact your dealer. Power switch USB connector Use this if you’re connecting the PCR to your computer via a USB cable. MIDI MERGE switch This switches the MIDI IN m ...

  • Roland PCR-800 - page 8

    8 Using control maps The PCR-300/500/800 have fifty fully assignable controllers; you can freely assign any MIDI message to each of these controllers. The MIDI settings assigned to the controllers are collectively called a “control map.” This is the same as what was called a “memory set” on previous models of the PCR series. For details on ...

  • Roland PCR-800 - page 9

    9 Using control maps When the PCR-300/500/800 is shipped from the factory, it contains sixteen control maps. By switching among these control maps, you can quickly select control maps that are suitable for a wide variety of software. For details on the memory numbers of these control maps and their factory settings, refer to Control map list (p. 90 ...

  • Roland PCR-800 - page 10

    10 Using control maps The PCR-300/500/800 can receive control map data in the form of a bulk dump. If you want control map data you’ve created using PCR Editor to be received into the PCR’s current memory, you’ll need to make settings in PCR Editor so that the PCR will be ready to receive a bulk dump. If you want the PCR to receive this data ...

  • Roland PCR-800 - page 11

    11 Using control maps 7 Operate PCR Editor or your DAW software to transmit the control map data. Select “EDIROL PCR” as the MIDI output device for PCR Editor or your DAW software. For details on how to make this setting in your DAW software, refer to the owner’s manual for the DAW software you’re using. fig.D-End.eps 8 When the PCR has fin ...

  • Roland PCR-800 - page 12

    12 Using control maps The PCR-300/500/800 can transmit control map data to your DAW software in the form of a bulk dump. In order to transmit a control map you’ve edited on the PCR keyboard to PCR Editor or other software you’re using, you’ll need to make settings on the PCR to make it transmit the bulk data. For more about PCR Editor, refer ...

  • Roland PCR-800 - page 13

    13 Using control maps By turning the Protect setting on, you can protect the control map data from being accidentally overwritten. This will disable All Bulk reception (p. 10) and Save (p. 9) operations, protecting your valuable data from being overwritten. The Protect on/off setting is remembered even when the PCR is powered off. fig.H-Edit.eps 1 ...

  • Roland PCR-800 - page 14

    14 Using PCR Editor PCR Editor Ver. 2 is an application that lets you use your computer to create control maps (called “memory sets” on earlier models of the PCR series) for the EDIROL PCR series. fig.controller.eps The PCR-300/500/800 has a total of fifty controllers: [R1]–[R9], [S1]–[S9], [A1]– [A9], [B1]–[B9], [C1]–[C3], [L1]–[L4 ...

  • Roland PCR-800 - page 15

    15 Using PCR Editor If you have not yet installed PCR Editor in your computer, install it now as described in the included setup guide. 1 Use a USB cable to connect the PCR to your computer, then switch on the PCR’s power. 2 In Windows, choose [Start]-[All Programs]-[PCR Editor V2]-[PCR Editor 2] to start up PCR Editor. 3 In PCR Editor, choose [O ...

  • Roland PCR-800 - page 16

    16 Using PCR Editor Explanation of the menus File menu Menu Explanation New Creates a new control map. In the new control map, all controllers will be set to “NO AS- SIGN.” Open Loads a control map that was saved in SMF format. For details, refer to Loading a control map (p. 23). Save Saves the control map currently being edited by overwriting ...

  • Roland PCR-800 - page 17

    17 Using PCR Editor You can use the following keyboard shortcuts in PCR Editor. * In some text boxes, such as the main window’s Title field, the [Edit]–[Copy] and [Edit]–[Paste] commands are used for text editing. Keyboard shortcuts Command Windows Macintosh [File]–[New] Ctrl + N Command + N [File]–[Open] Ctrl + O Command + O [File]–[Sa ...

  • Roland PCR-800 - page 18

    18 Using PCR Editor fig.EditorMainWindow-e.eps Title You can enter a name for the control map currently being edited. Only single-byte alphanumeric characters can be entered as the control map name. The name you enter here is displayed as the title of the HTML file produced by the [File]-[Export Assign List] command. Controllers Click the controlle ...

  • Roland PCR-800 - page 19

    19 Using PCR Editor Output Port This specifies the USB port on the USB-connected computer to which the MIDI message will be sent. Button Mode For a button-type controller, this specifies the button’s mode. Aftertouch Mode If the controller currently being edited is [A1]–[A9] or [B1]–[B9], this specifies the aftertouch setting. Virtual Center ...

  • Roland PCR-800 - page 20

    20 Using PCR Editor Here’s how to assign a MIDI message to each controller. fig.EH-Assign.eps_81 1 In the main window, click the controller to which you want to assign a MIDI message. fig.EH-AssignMessage.eps_25 2 In the message assignment window, use the Assign Message field to select the type of MIDI message that you want to assign. fig.EH-Assi ...

  • Roland PCR-800 - page 21

    21 Using PCR Editor You can use either of the following two methods to view the MIDI messages you’ve assigned. Assignment list If you want to use your browser to view a list of the assignments for the current control map, choose [File]-[View Assign List]. This method is convenient when you want to see the control map settings at a glance. If you ...

  • Roland PCR-800 - page 22

    22 Using PCR Editor If you’ve used PCR Editor to create control map settings and want to use them on the PCR keyboard, you’ll need to send the control map currently being edited to the PCR’s current memory as described below. * When you send this data, the PCR’s current memory will be overwritten. If you want to preserve the settings of the ...

  • Roland PCR-800 - page 23

    23 Using PCR Editor A control map that you edit using PCR Editor can be saved as an SMF-format file on your computer, as well as being transferred to or from the PCR keyboard. * The comments that have been entered for the controllers are also saved in the SMF. To save a control map as an SMF file, proceed as follows. 1 From the menu bar, choose [Fi ...

  • Roland PCR-800 - page 24

    24 Using PCR Editor The setting items shown in the message assign window will depend on the MIDI message you’ve selected. This section explains the setting items for each MIDI message. Values for parameters are specified in decimal. * Within the explanation, values in square brackets [ ] are in hexadecimal. Clears any message assignment. No messa ...

  • Roland PCR-800 - page 25

    25 Using PCR Editor Polyphonic Key Pressure [An kk vv] Assign a polyphonic key pressure message. fig.EditorPolyKeyPres.eps_35 You can specify the following parameters for Polyphonic Key Pressure. Control Change [Bn cc vv] Assign a control change message. fig.EditorCC.eps_35 You can specify the following parameters for Control Change. Program Change ...

  • Roland PCR-800 - page 26

    26 Using PCR Editor Program Change (Min-Max) [Cn pp] Assign a program change message (with a variable program number). fig.EditorPC2.eps_35 You can specify the following parameters for Program Change (Min-Max). * The range of the program number [pp] is 1–128. Bank Select + Program Change [Bn 00 mm Bn 20 ll Cn pp] Assign a bank select message and ...

  • Roland PCR-800 - page 27

    27 Using PCR Editor Program Change – Inc Assign the program change increment function (PC INC). This will transmit a program change number that is one greater than the program change number most recently transmitted in the PCR’s program change mode. fig.EditorPCInc.eps_35 There are no parameters to specify for Program Change – Inc. RPN [Bn 65 ...

  • Roland PCR-800 - page 28

    28 Using PCR Editor Encoder Simulate [Bn cc 41] – [Bn cc 01] Assign a function that simulates a rotary encoder. fig.EditorEncoder.eps_35 You can specify the following parameters for Encoder Simulate. * This can be assigned to a button, but will not do anything. Assign a system realtime message or F6 (Tune Request). fig.EditorSR.eps_35 For System ...

  • Roland PCR-800 - page 29

    29 Using PCR Editor Assign a system exclusive message (System Ex.). You can enter up to twenty-four bytes. fig.EditorSysEx.eps_35 You can specify the following parameters for System Ex. Table 1: Special characters used in the message entry field Table 2: Types of data you can specify in the Data Type field System Ex. [F0...F7] Item Content Message ...

  • Roland PCR-800 - page 30

    30 Using PCR Editor Assign a MIDI message. You can enter up to twenty-four bytes. You may assign more than one MIDI message if desired. fig.EditorFreeMessage.eps_35 You can specify the following parameters for Free Message. Assign tempo control for transmitting MIDI Clock messages. fig.EditorTempo.eps_35 There are no parameters to specify for Tempo ...

  • Roland PCR-800 - page 31

    31 Using PCR Editor PCR-300_500_800_e.book 31 ページ ２００６年１２月１９日　火曜日　午後２時５９分 ...

  • Roland PCR-800 - page 32

    32 Playing (Play mode) Use Play mode when you want to play the PCR’s keyboard or use its controllers to control your software or sound module. Broadly speaking, the PCR has two modes. When you turn on the power, the PCR-300/500/800 will start up in Play mode. To return from Edit mode (p. 41) back to Play mode, press the [EDIT] button or the [CANC ...

  • Roland PCR-800 - page 33

    33 Playing (Play mode) Here’s how to specify the current channel, which will be used to transmit data produced by playing the keyboard as well as other performance data. Here’s how to change the current channel (MIDI transmit channel). fig.H-MIDI-Ch.eps 1 Press the [MIDI CHANNEL] button. The [MIDI CHANNEL] button will light. The display will in ...

  • Roland PCR-800 - page 34

    34 Playing (Play mode) You can select sounds on your sound module from the PCR by transmitting Program Changes. To select sounds in a different bank, you must first use Bank mode to transmit a Bank Select message to switch the bank. Then transmit a Program Change message. The bank select message must be transmitted before the program change. Here? ...

  • Roland PCR-800 - page 35

    35 Playing (Play mode) In order to switch the bank number, you’ll need to make system settings for “Value Encoder” so that [USER] is assigned to “BANK SELECT LSB” or “BANK SELECT MSB.” * For details on how to make this setting, refer to this page or VALUE knob settings (p. 80). If “BANK SELECT LSB” or “BANK SELECT MSB” is assi ...

  • Roland PCR-800 - page 36

    36 Playing (Play mode) The PCR-300/500/800’s keyboard has two parts—Lower and Upper—and you can select different sounds for each part. The entire keyboard will play the Lower sound. fig.Lower.eps_80 1 Press the [LOWER] button so it’s lit. 2 Press the [PROGRAM CHANGE] button, and turn the VALUE knob. The Lower sound will change. When you pla ...

  • Roland PCR-800 - page 37

    37 Playing (Play mode) Dual lets you play both the Lower sound and Upper sound from the entire keyboard. The entire keyboard will play both the Lower and Upper sounds. fig.Dual.eps_80 1 Press the [DUAL/SPLIT] button several times to make it light. * If you want to change the Upper sound, press the [UPPER] button. Split lets you specify a boundary b ...

  • Roland PCR-800 - page 38

    38 Playing (Play mode) Normally, the velocity value of the transmitted notes will vary depending on how strongly you play the keyboard. If desired, you can also specify a fixed velocity at which all notes will be transmitted regardless of how strongly you play the keyboard. This is convenient when you want to record into your DAW software at a fixe ...

  • Roland PCR-800 - page 39

    39 Playing (Play mode) You can set the controllers to the desired positions and then transmit their state as a “snapshot.” The snapshot function will transmit the current values of the controllers [R1]–[R9], [S1]– [S9], and [H1]–[H2] in a single operation. This is a convenient way to send control data to your DAW software. You can use thi ...

  • Roland PCR-800 - page 40

    40 Playing (Play mode) If you experience problems during operation such as notes on your sound module that fail to turn off, or if something is wrong with the sound, you can use the Panic function to fix the problem. The Panic function will transmit All Sound Off, All Notes Off, and Reset All Controllers messages on all channels. fig.H-PANIC.eps 1 ...

  • Roland PCR-800 - page 41

    41 Settings (Edit mode) The PCR-300/500/800 has a total of fifty controllers: [R1]–[R9], [S1]–[S9], [A1]–[A9], [B1]–[B9], [C1]–[C3], [L1]–[L4], [H1]–[H2], [P1]–[P2], [BEND], [MOD], and [AFTERTOUCH]. You can freely assign the MIDI message that will be transmitted by each of these controllers. You need to use Edit mode to make MIDI me ...

  • Roland PCR-800 - page 42

    42 Settings (Edit mode) Here’s how to assign a note message to a controller. Note messages are used in a performance, and can also be used to control DAW software. Basic editing (-> Advanced editing 1 (p. 43)) fig.H-Edit.eps 1 Press the [EDIT] button so it’s lit. fig.D-Edit.eps The display will indicate “EDIT.” fig.D-r1.eps 2 Slightly mo ...

  • Roland PCR-800 - page 43

    43 Settings (Edit mode) * If you assign a note message to [S1]–[S9], [R1]–[R9], or [P2], moving the controller to the maximum position will transmit a note message with the specified velocity value. Slightly lowering the controller from the maximum position will transmit a note message with a velocity of 0. * If you assign a note message to [A1 ...

  • Roland PCR-800 - page 44

    44 Settings (Edit mode) Here’s how to assign an aftertouch message to a controller. Basic editing (-> Advanced editing 1–3 (p. 45)) fig.H-Edit.eps 1 Press the [EDIT] button so it’s lit. fig.D-Edit.eps The display will indicate “EDIT.” fig.D-r1.eps 2 Slightly move the controller to which you want to assign aftertouch. If the controller ...

  • Roland PCR-800 - page 45

    45 Settings (Edit mode) Advanced editing 1–3 In Aftertouch Assign advanced editing 1, you can specify an upper and lower limit for the aftertouch data as well as edit the basic editing items. In advanced editing 2 and 3, you can also specify note aftertouch data (Polyphonic Key Pressure) instead of a channel. 1. Press the [EDIT] button so it’s ...

  • Roland PCR-800 - page 46

    46 Settings (Edit mode) Here’s how to assign a control change message to a controller. Basic editing (-> Advanced editing (p. 47)) fig.H-Edit.eps 1 Press the [EDIT] button so it’s lit. fig.D-Edit.eps The display will indicate “EDIT.” fig.D-r1.eps 2 Slightly move the controller to which you want to assign a control change message. If the ...

  • Roland PCR-800 - page 47

    47 Settings (Edit mode) Advanced editing 1 In control change assign advanced editing 1, you can specify an upper and lower limit for the control change data, in addition to setting the items available in basic editing. 1. Press the [EDIT] button so it’s lit. 2. Slightly move the controller to which you’re assigning a control change message. If ...

  • Roland PCR-800 - page 48

    48 Settings (Edit mode) Here’s how to assign a program change message to a controller. Basic editing (-> Advanced editing 1, 2 (p. 50), Advanced editing 3 and 4 (p. 51)) fig.H-Edit.eps 1 Press the [EDIT] button so it’s lit. fig.D-Edit.eps The display will indicate “EDIT.” fig.D-r1.eps 2 Slightly move the controller to which you want to a ...

  • Roland PCR-800 - page 49

    49 Settings (Edit mode) fig.D-NoteSelect.eps 9 Press the [ENTER] button. The display will indicate “N- -.” * The - - portion shows the currently specified value. 10 Use the VALUE knob or controllers [A1]–[A8] and [B1]–[B8] to specify the desired program number. 11 Press the [ENTER] button. If you’ve assigned this basic editing function to ...

  • Roland PCR-800 - page 50

    50 Settings (Edit mode) Advanced editing 1, 2 Program Change Assign advanced editing 1 lets you specify an upper limit and lower limit for the program change message. Advanced editing 2 lets you transmit Bank LSB/LSB settings along with the program change. 1. Press the [EDIT] button so it’s lit. 2. Slightly move the controller to which you want t ...

  • Roland PCR-800 - page 51

    51 Settings (Edit mode) * By “most recently transmitted program change number,” we mean the value that was last transmitted by the advanced editing 3 and 4 or program change functions (p. 34). * Program changes transmitted by the basic editing or advanced editing 1 and 2 functions have no effect on PC DEC or PC INC. Advanced editing 3 and 4 Adv ...

  • Roland PCR-800 - page 52

    52 Settings (Edit mode) You can assign a controller to adjust the speed of the F8 clock (20–250). * In order to transmit F8 clock, the F8 clock setting must be “ON.” (-> F8 Clock On/Off (p. 70)) fig.H-Edit.eps 1 Press the [EDIT] button so it’s lit. fig.D-Edit.eps The display will indicate “EDIT.” fig.D-r1.eps 2 Slightly move the cont ...

  • Roland PCR-800 - page 53

    53 Settings (Edit mode) You can assign an RPN or NRPN to a controller. Basic editing (-> Advanced editing 1 (p. 54)) fig.H-Edit.eps 1 Press the [EDIT] button so it’s lit. fig.D-Edit.eps The display will indicate “EDIT.” fig.D-r1.eps 2 Slightly move the controller to which you want to assign an RPN or NRPN message. If the controller is a bu ...

  • Roland PCR-800 - page 54

    54 Settings (Edit mode) Advanced editing 1 RPN/NRPN advanced editing 1 lets you specify the upper limit and lower limit for the data entry MSB (CC#6) of the transmitted RPN/NRPN message, in addition to allowing you to make the settings described in basic editing. 1. Press the [EDIT] button so it’s lit. 2. Slightly move the controller to which you ...

  • Roland PCR-800 - page 55

    55 Settings (Edit mode) You can assign a system exclusive message to a controller. Advanced editing 2 lets you assign a single-byte system message (system realtime message, tune request). Advanced editing 3 and 4 let you freely assign a message of up to twenty-four bytes. System exclusive assign lets you automatically calculate the checksum, or ins ...

  • Roland PCR-800 - page 56

    56 Settings (Edit mode) System exclusive assignment procedure fig.H-Edit.eps 1 Press the [EDIT] button so it’s lit. fig.D-Edit.eps The display will indicate “EDIT.” fig.D-r1.eps 2 Slightly move the controller to which you want to assign a system exclusive message. If the controller is a button, press it. The display will indicate the number o ...

  • Roland PCR-800 - page 57

    57 Settings (Edit mode) Using advanced editing 2 fig.D-F.eps The display will indicate “F-.” * The – portion shows the currently specified value. 8 Use the VALUE knob or controllers [A7 (6)], [B1 (8)], [B3 (A)]–[B5 (C)], and [B8 (F)] to specify the system exclusive message. 9 Press the [ENTER] button. 10 Specify the output port. (-> Port ...

  • Roland PCR-800 - page 58

    58 Settings (Edit mode) System exclusive message assignment examples • Specifying a checksum (p. 58) • Specifying the location of the data (p. 59) • Entering channel/block data (p. 60) Specifying a checksum The PCR-300/500/800 can automatically calculate a checksum within a system exclusive message and insert the result of this calculation in ...

  • Roland PCR-800 - page 59

    59 Settings (Edit mode) Specifying the location of the data As described below, you can specify the location and type of the variable data to be inserted in the system exclusive message. For basic editing and advanced editing 3, the range of data values will be the default range. For advanced editing 1 and advanced editing 4, it will be the range s ...

  • Roland PCR-800 - page 60

    60 Settings (Edit mode) Entering channel/block data If the system exclusive message contains a channel or GS block number, use the following procedure to specify the type and the value of the upper bits. A channel or block number corresponding to the current channel (p. 33) will be inserted into the lower bits. The block number is not actually a ch ...

  • Roland PCR-800 - page 61

    61 Settings (Edit mode) Examples of system exclusive message assignments • GM2 System On (p. 61) • Master Volume (p. 62) • Bend Pitch Control (p. 63) Here are some specific examples of system exclusive messages. GM2 System On “F0 7E 7F 09 03 F7” Let’s use basic editing mode to enter a GM2 System On system exclusive message. 1 Press the ...

  • Roland PCR-800 - page 62

    62 Settings (Edit mode) Master Volume “F0 7F 7F 04 01 vL vM F7” Since the data range of the Master Volume message is 00 00–7F 7F and there’s no need to specify this range, you can choose basic editing. Since the data format is two bytes in the order of LSB MSB, choose “DT3” (p. 59) when inserting the data. 1 Press the [EDIT] button so i ...

  • Roland PCR-800 - page 63

    63 Settings (Edit mode) Bend Pitch Control The GS message Bend Pitch Control has a data range of 40H–58H (0–24 semitones), so you should choose advanced editing 1, which lets you specify the region. Since the data format is one byte, you should choose “DT0” (p. 59) when inserting the data. fig.checksum-e.eps 1 Press the [ENTER] button. The ...

  • Roland PCR-800 - page 64

    64 Settings (Edit mode) Input mode setting When entering numeric values in modes other than Play mode, you can use either Decimal input mode or Hexadecimal input mode. Press the [DECIMAL] button if you want to use decimal input mode, or press the [HEX] button if you want to use hexadecimal input mode. * When you turn on the power, the PCR will star ...

  • Roland PCR-800 - page 65

    65 Settings (Edit mode) Virtual center click setting When using edit mode to assign MIDI messages on the PCR keyboard (p. 41), and you’re assigning a message to a knob [R1]–[R9] or slider [S1]–[S8], you’ll need to specify whether the virtual center click will be on or off. 1. Turn the VALUE knob to select On or Off. The PCR’s knobs and sl ...

  • Roland PCR-800 - page 66

    66 Settings (Edit mode) A message assigned to a controller can be copied to another controller. For example, if you want to assign similar functions to more than one controller, you can assign the desired MIDI message to one controller and copy the assignment to other controllers for greater efficiency. If you copy an assigned message between contr ...

  • Roland PCR-800 - page 67

    67 Settings (Edit mode) Here’s how to cancel the MIDI message assigned to a controller. If you’ve cancelled the assignment, moving that controller will not transmit any MIDI message. * If you cancel the MIDI message assignment for bender, modulation, aftertouch, hold (P1), or expression (P2), these controllers will revert to controlling their o ...

  • Roland PCR-800 - page 68

    68 System settings Here’s how to make system settings for the PCR-300/500/800. The system setting items are listed below. Category Controller Display Item Contents Factory setting Procedure Clock [A1 (0)] F8 CLOCK ON/OFF Specifies whether F8 Clock will be transmitted. OFF p. 70 [A2 (1)] F8 CLOCK DEFAULT TEMPO If “F8 Clock On/Off” is on, this ...

  • Roland PCR-800 - page 69

    69 System settings MIDI [B1 (8)] MIDI I/F SWITCH Specifies whether the MIDI connectors will be used as a MIDI inter- face. ON p. 76 [B2 (9)] MIDI MERGE DESTINATION Specifies the port that will be merged when the “MIDI MERGE” switch is On. PORT 1 p. 77 [A2 (1)] + [A1 (0)] ADVANCED DRIVER SWITCH Switches the driver operation mode. * If you change ...

  • Roland PCR-800 - page 70

    70 System settings Here’s how to specify whether F8 Clock will be transmitted. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY00,” and press the [ENTER] button. 4 Use the VALUE knob or controllers [A1] and ...

  • Roland PCR-800 - page 71

    71 System settings Here’s how to specify the port from which F8 Clock will be sent when “F8 Clock On/ Off” is On. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY02,” and press the [ENTER] button. 4 Use ...

  • Roland PCR-800 - page 72

    72 System settings Here’s how to specify how the velocity transmitted when you play the keyboard will respond to your playing strength. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY03,” and press the [ENT ...

  • Roland PCR-800 - page 73

    73 System settings [A7 (6)] 3-LIGHT These velocity curves produce less change in response to variations in your playing strength, making it easier for you to main- tain a consistent playing volume. You can produce high velocity values (volumes) even by playing the keyboard softly. [A8 (7)] 3-MEDIUM The keyboard sensitivity will be normal. [B1 (8)] ...

  • Roland PCR-800 - page 74

    74 System settings Here’s how to specify the port that will transmit performance data from the keyboard and bender lever. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY04,” and press the [ENTER] button. 4 ...

  • Roland PCR-800 - page 75

    75 System settings Here’s how to specify how the velocity transmitted when you play the pad controllers [A1]–[A9] and [B1]–[B9] will respond to your playing strength. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to se ...

  • Roland PCR-800 - page 76

    76 System settings Here’s how to specify whether the MIDI connectors will be used as a MIDI interface. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY08,” and press the [ENTER] button. 4 Use the VALUE knob ...

  • Roland PCR-800 - page 77

    77 System settings The PCR-300/500/800 has a MIDI MERGE switch. The MIDI Merge Destination setting specifies the port that will be merged when the MIDI MERGE switch is ON. The MIDI Merge function is convenient when you’ve connected an external MIDI controller other than the PCR to the PCR’s MIDI IN connector. For example, you could connect anot ...

  • Roland PCR-800 - page 78

    78 System settings Here’s how to switch ADVANCED DRIVER ON/OFF. Normally, we recommend that you use ON . * Changes you make to this setting will take effect the next time you turn on the power. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 U ...

  • Roland PCR-800 - page 79

    79 System settings Here’s how to specify the control map that will be selected when you turn on the power. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY12,” and press the [ENTER] button. 4 Use the VALUE k ...

  • Roland PCR-800 - page 80

    80 System settings Here’s how to specify the function that will be controlled by the VALUE knob when you press the [USER] button. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY14,” and press the [ENTER] bu ...

  • Roland PCR-800 - page 81

    81 System settings Here’s how to specify the function of the DYNAMIC MAPPING/V-LINK button. 1 Press the [EDIT] button so it’s lit. The display will indicate “EDIT.” 2 Use the VALUE knob to select “SYS,” and press the [ENTER] button. 3 Use the VALUE knob to select “SY15,” and press the [ENTER] button. 4 Use the VALUE knob or controll ...

  • Roland PCR-800 - page 82

    82 Troubleshooting If you experience problems, read this chapter first. It contains tips for resolving problems. ● Is the PCR connected correctly? Make sure that the PCR is connected to the USB connector of your computer via a USB cable. After making the USB connection, it may take fifteen seconds or more for your computer to detect the PCR. ● ...

  • Roland PCR-800 - page 83

    83 Troubleshooting ● Could you have connected the PCR to a USB connector that’s different than the one used when you installed the driver? The USB driver must be installed for each USB connector to which you connect the PCR. If you have a USB hub or a computer that has more than one USB connector, you should normally connect the PCR to the USB ...

  • Roland PCR-800 - page 84

    84 Troubleshooting If you were unable to install the USB driver using the procedure given, it is possible that your computer did not recognize the PCR’s USB driver correctly. In this case, you’ll need to delete the incorrectly installed USB driver. Follow the procedure below to delete the USB driver, and then re-install it. Windows users 1 Disc ...

  • Roland PCR-800 - page 85

    85 Troubleshooting ● In Windows XP/2000, have you made settings to “give priority to background processing”? To ensure that MIDI processing occurs smoothly, make settings to “give priority to background processing.” Separate sheet: Setup Guide ● Could you have disconnected and reconnected the USB cable? Try closing all DAW software that ...

  • Roland PCR-800 - page 86

    86 Troubleshooting By its nature, a software synthesizer produces sound via the sound card of your computer. There will be a time lag before the sound of the software synthesizer is actually played back from the sound card, and this is known as the “latency.” There will always be some latency for any combination of software synthesizer and soun ...

  • Roland PCR-800 - page 87

    87 Appendix PCR-300_500_800_e.book 87 ページ ２００６年１２月１９日　火曜日　午後２時５９分 ...

  • Roland PCR-800 - page 88

    88 Two MIDI ports If the PCR is connected to your computer via USB, the PCR will be able to use two MIDI output ports (PORT 1 and PORT 2). Each controller of the PCR can be assigned to send its MIDI messages to either port. For details on how to make this assignment, refer to Using PCR Editor to assign MIDI messages (p. 20) or Assigning MIDI messag ...

  • Roland PCR-800 - page 89

    89 Connecting the PCR directly to a sound module You can connect the PCR connected directly to a MIDI sound module, and use it to play and control the sound module. If you’re not connecting the PCR to your computer via USB, you’ll need to use a separately available AC adaptor (p. 92). You can purchase the appropriate AC adaptor from your dealer ...

  • Roland PCR-800 - page 90

    90 Control map list When the PCR-300/500/800 is shipped from the factory, it contains sixteen control maps. By switching among these control maps, you can quickly select control maps that are suitable for a wide variety of software. Refer to Using control maps (p. 8). You can also download the latest control maps from the Roland website and load th ...

  • Roland PCR-800 - page 91

    91 MIDI implementation chart Function... Basic Channel Mode Note Number Velocity Aftertouch Pitch Bend Control Change Program Change System Exclusive System Common System Real Time Aux Message Notes Transmitted Recognized Remarks Default Changed Default Messages Altered : True Voice Note ON Note OFF Key’s Ch’s 0–119 : True # : Song Pos : Song ...

  • Roland PCR-800 - page 92

    92 Main specifications PCR-300/500/800: MIDI KEYBOARD CONTROLLER Keyboard PCR-300: 32 keys (with velocity and channel aftertouch) PCR-500: 49 keys (with velocity and channel aftertouch) PCR-800: 61 keys (with velocity and channel aftertouch) Controllers Pads: [A1]–[A9], [B1]–[B9] Buttons: [L1]–[L4], [C1]–[C3] Knobs: [R1]–[R9] Sliders: [S1 ...

  • Roland PCR-800 - page 93

    93 Index A AC Adaptor ............................................................. 89, 92 Advanced Driver Switch ............................................. 78 Advanced Editing ......................................................... 41 Aftertouch ................................................................ 74–75 Aftertouch Assign ....... ...

  • Roland PCR-800 - page 94

    94 Index Curve Keyboard Aftertouch .............................................. 74 Keyboard Velocity .................................................. 72 Pad Aftertouch ........................................................ 75 Pad Velocity ............................................................. 75 D DATA Button .......................... ...

  • Roland PCR-800 - page 95

    95 Index Keyboard Shortcuts ...................................................... 17 Keyboard Velocity Curve ............................................ 72 Knobs ................................................................................ 6 L Latch ......................................................................... 19, 64 LOWER Button . ...

  • Roland PCR-800 - page 96

    96 Index PORT 1+2 ....................................................................... 65 PORT 2 ........................................................................... 65 Power Switch ................................................................... 7 PRM MUTE .................................................................... 39 PRM MUT ...

  • Roland PCR-800 - page 97

    NOTE ASSIGN Edit mode PCR keyboard settings AFTERTOUCH ASSIGN CONTROL CHANGE ASSIGN PROGRAM CHANGE ASSIGN RPN/NRPN ASSIGN RPN/NRPN ASSIGN Sys Ex. ASSIGN TEMPO ASSIGN Canceling an assignment (NO ASSIGN) Controllers : : -> Setting the Split point (p. 37) -> Saving a control map (p. 9) -> What is OMNI? (p. 33) -> Protecting the control map ...

  • Roland PCR-800 - page 98

    Memo PCR-300_500_800_e.book 98 ページ ２００６年１２月１９日　火曜日　午後２時５９分 ...

  • Roland PCR-800 - page 99

    2 As of November 1, 2006 (EDIROL-1) Information When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor in your country as shown below. CHINA Roland Shanghai Electronics Co.,Ltd. 5F. No.1500 Pingliang Road Shanghai 200090, CHINA TEL: (021) 5580-0800 Roland Shanghai Electronics Co.,Ltd. (B ...

  • Roland PCR-800 - page 100

    04348534 1MP PCR-300_500_800_e.book 100 ページ ２００６年１２月１９日　火曜日　午後２時５９分 ...

Manufacturer Roland Category Musical Instrument

Documents that we receive from a manufacturer of a Roland PCR-800 can be divided into several groups. They are, among others:
- Roland technical drawings
- PCR-800 manuals
- Roland product data sheets
- information booklets
- or energy labels Roland PCR-800
All of them are important, but the most important information from the point of view of use of the device are in the user manual Roland PCR-800.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Roland PCR-800, service manual, brief instructions and user manuals Roland PCR-800. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Roland PCR-800.

Similar manuals

A complete manual for the device Roland PCR-800, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Roland PCR-800 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Roland PCR-800.

A complete Roland manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Roland PCR-800 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Roland PCR-800, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Roland PCR-800, that we can find in the current document
3. Tips how to use the basic functions of the device Roland PCR-800 - which should help us in our first steps of using Roland PCR-800
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Roland PCR-800
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Roland PCR-800 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Roland PCR-800?

Use the form below

If you did not solve your problem by using a manual Roland PCR-800, ask a question using the form below. If a user had a similar problem with Roland PCR-800 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)