English dropdown-ico

Manual Napoleon Fireplaces NPS40

40 pages 3.35 mb
Download

Go to site of 40

Summary
  • Napoleon Fireplaces NPS40 - page 1

    W415-0616 / B / 02.18.08 1 W415-0616 / B / 02.18.08 $10.00 ...

  • Napoleon Fireplaces NPS40 - page 2

    W415-0616 / B / 02.18.08 2 T ABLE of CONTENTS PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE PG 3-5 INTRODUCTION W arranty W arnings and safety precautions 6-10 GENERAL INTRODUCTION General Instructions Pellet Quality Specifi cations Heating Specifi cations Dimensions Specifi cations EP A Compliance 10-11 GENERAL INST ALLA TION Planning your Ins ...

  • Napoleon Fireplaces NPS40 - page 3

    W415-0616 / B / 02.18.08 3 NAPOLEON ® Pellet Heaters are manufactured under the strict Standard of the World Recognized ISO 9001 : 2000 Quality Assurance Certifi cate. NAPOLEON ® products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. The complete fi replace is thoroughly ...

  • Napoleon Fireplaces NPS40 - page 4

    W415-0616 / B / 02.18.08 4 WARNINGS AND SAFETY PRECA UTIONS ...

  • Napoleon Fireplaces NPS40 - page 5

    W415-0616 / B / 02.18.08 5 WARNINGS AND SAFETY PRECA UTIONS ...

  • Napoleon Fireplaces NPS40 - page 6

    W415-0616 / B / 02.18.08 6 GENERAL INTR ODUCTION GENERAL INSTRUCTIONS Thank you for purchasing the Napoleon® Pellet Heater . This heater is designed for use with Pelletized Wood Only . Please read this entire manual before installation and use of this pellet fuel-burning room heater . Failure to follow these instruc- tions could result in property ...

  • Napoleon Fireplaces NPS40 - page 7

    W415-0616 / B / 02.18.08 7 DIMENSIONS Figures 1a-b NPI40 with NI800 Flashing Shown NPS40 Figures 2a-c ...

  • Napoleon Fireplaces NPS40 - page 8

    W415-0616 / B / 02.18.08 8 DIMENSIONS CONTINUED Figures 3a-c NPI40 with AK9 Adapter and CISK Flashing Shown ...

  • Napoleon Fireplaces NPS40 - page 9

    W415-0616 / B / 02.18.08 9 DIMENSIONS CONTINUED Figures 4a-c NPI40 with AK8 Adapter and GICSK Flashing Shown ...

  • Napoleon Fireplaces NPS40 - page 10

    W415-0616 / B / 02.18.08 10 GENERAL INST ALLA TION HEA TER PLA CEMENT PLANNING Y OUR INST ALLA TION Have an authorized Napoleon® dealer install the heater . If you install the heater yourself, have your dealer review your installation plans and/or installation. Draw out a detailed plan of the installation including dimensions and verify the dimens ...

  • Napoleon Fireplaces NPS40 - page 11

    W415-0616 / B / 02.18.08 11 SAFETY FEA TURES BLOWER OVER-RIDE SWITCH: Y our heater is equipped with a convection blower that circulates hot air into your room. This switch will automatically turn the blower on, when the temperature at the back of the fi re box reaches a cer- tain temperature. The blower can cycle from your desired setting to maxim ...

  • Napoleon Fireplaces NPS40 - page 12

    W415-0616 / B / 02.18.08 12 GENERAL VENTING Must be an approved 3" or 4" Diameter T ype "L" or "PL" vent, vented to the outside or connect the vent to a factory built type "A" chimney using an adaptor; and/or stainless steel chimney liner for masonry fi replace installations. Use 4" diameter vent if ven ...

  • Napoleon Fireplaces NPS40 - page 13

    W415-0616 / B / 02.18.08 13 * * * * * Recommended to prevent condensation on windows and thermal breakage ** This is a recommended distance . For additional r equir ements chec k local codes . A B C D E F G H I K 24 INCHES 48 INCHES 12 INCHES* 18 INCHES 0 INCHES 3 INCHES 9 INCHES 3 FEET 7 FEET** 12 INCHES** 24 INCHES 2 FEET Clearance above grade, v ...

  • Napoleon Fireplaces NPS40 - page 14

    W415-0616 / B / 02.18.08 14 NPS40 INST ALLA TION STRAIGHT INST ALLA TION Through the W all Installations Interior V ertical V ents CORNER INST ALLA TION Through the W all V ents Interior V ertical V ents NOTE: If interior vertical pellet vent is used, the clearance to the back wall is determined by the upward-turning elbow or "T ee". It w ...

  • Napoleon Fireplaces NPS40 - page 15

    W415-0616 / B / 02.18.08 15 VENTING INST ALLA TION EXAMPLES HORIZONT AL EXHAUST THR OUGH WALL INST ALLA TION Figure 13 THROUGH WALL WITH VERTICAL RISE AND HORIZONT AL TERMINA TION INST ALLA TION Figure 14 ...

  • Napoleon Fireplaces NPS40 - page 16

    W415-0616 / B / 02.18.08 16 MINIMUM INSIDE VERTICAL CLEARANCES Outside air (Recommended) (Installation showing inlet of out- side air in ventilated crawl space) Ceiling Support V ent must maintain 3” clearance to combus- tibles. V ertical Cap Roof Flashing Storm Collar Floor Protection 3” 2” Class A Chimney Ceiling Support Outside air (Recomm ...

  • Napoleon Fireplaces NPS40 - page 17

    W415-0616 / B / 02.18.08 17 Figure 17 HEARTH MOUNT INST ALLA TION Floor Protection 6” MIN Clean-out tee Outside Air (Recommended) Storm Collar V ertical Cap Chimney Cap Bring outside air to the stove Pellet Liner Flue Cover Pellet Ve n t Clean all ashes out of the inside of the fi replace. Make sure that the chimney and fi replace are free of c ...

  • Napoleon Fireplaces NPS40 - page 18

    W415-0616 / B / 02.18.08 18 NPI40 INST ALLA TION O VER VIEW See the section “INST ALLA TION - MINIMUM MANTEL CLEARANCES” Drywall (or other combustible material) See the sections “GENERAL VENTING” and “INST ALLA TION” See the section “MINIMUM FRAM- ING DIMENSIONS” Side W all See the section “MINIMUM CLEARANCES TO COMBUSTIBLES” Se ...

  • Napoleon Fireplaces NPS40 - page 19

    W415-0616 / B / 02.18.08 19 Figure 22 INST ALLA TION INT O A MASONR Y FIREPLACE Stand-offs (See Dimensions on page 7) may be removed to fi t the insert into the fi replace. When installing the insert into a masonry fi replace, do not remove any bricks or masonry . If necessary , the damper plate may be removed from the smoke shelf, to accommodat ...

  • Napoleon Fireplaces NPS40 - page 20

    W415-0616 / B / 02.18.08 20 INST ALLA TION INT O A F A CTOR Y BUIL T (MET AL) FIREPLACE Figure 23 Stand-offs (See Dimensions on page 7) may be removed to fi t the insert into the fi replace. When installing the insert into a factory built fi replace, you must not modify any part that would alter the integrity in any way . Bolted or screwed toget ...

  • Napoleon Fireplaces NPS40 - page 21

    W415-0616 / B / 02.18.08 21 INST ALLA TION INT O A COMB USTIBLE BUIL T -IN ENCLOSURE Figure 24a MINIMUM FRAMING DIMENSIONS When installing the insert as a "Built-in" heater , it is important to maintain the "Clearances to Combustibles" as illustrated in Figure 24a-b. A non-combustible heart must cover the fl ooring underneath, ...

  • Napoleon Fireplaces NPS40 - page 22

    W415-0616 / B / 02.18.08 22 Figure 25 MINIMUM ENCLOSURE CLEARANCES ...

  • Napoleon Fireplaces NPS40 - page 23

    W415-0616 / B / 02.18.08 23 1. Secure the Right Flashing to the right side of the unit using two of the #8 x 1/2" screws . NOTE: Feed the Air Control Rod into the Air Control Slot on the Right Flashing before securing. (FIGURE 26) 2. T wist spring handle (supplied with the heater) onto the air control rod until it hits the stop. 3. Remove the ...

  • Napoleon Fireplaces NPS40 - page 24

    W415-0616 / B / 02.18.08 24 CAUTION: Never use gasoline, lantern fuel, lighter fl uid to start or "freshen-up" a fi re in this heater . Keep all such fl uids away from heater when in use. Due to different installation set ups, length and size of venting and fuel quality , the low feed setting from the factory will not always be correct ...

  • Napoleon Fireplaces NPS40 - page 25

    W415-0616 / B / 02.18.08 25 ! W ARNING GENERAL MAINTENANCE NPS40 AND NPI40 D AIL Y ( WHENEVER USING THE HEA TER ) The front of the heater becomes very hot during opera- tion. Let the heater cool completely before conducting service. 1. Open the side doors on either side of the heater . 2. On the right side of the heater are two latches. Release the ...

  • Napoleon Fireplaces NPS40 - page 26

    W415-0616 / B / 02.18.08 26 Make certain the heater has fully cooled (approximately 25 minutes) before opening the door and conducting service. T o clean the burn pot, open the door and knock away any debris on the burn pot. If se- verely clogged, remove the burn pot to gain bet- ter access. If removing the burn pot set aside on a non-combustible s ...

  • Napoleon Fireplaces NPS40 - page 27

    W415-0616 / B / 02.18.08 27 The products of combustion will contain small particles of fl y ash. The fl y ash will collect in the exhaust venting system and restrict the fl ow of the fl ue gases. Incomplete combustion occurs during startup, shutdown, or incorrect operation of the room heater will lead to some soot formation which will collect i ...

  • Napoleon Fireplaces NPS40 - page 28

    W415-0616 / B / 02.18.08 28 Inspect the door gasket to make sure it is fully attached. Heater gasket cement can be used to re-attach if necessary . If the door gasket is worn or fl attened, replace. Check the door to make sure it latches correctly . The latch should engage with a slight amount of resistance, yet not be too diffi cult. If the glas ...

  • Napoleon Fireplaces NPS40 - page 29

    W415-0616 / B / 02.18.08 29 Figure 48 NORMAL OPERA TING SOUNDS ...

  • Napoleon Fireplaces NPS40 - page 30

    W415-0616 / B / 02.18.08 30 WIRING DIA GRAM Figure 49 ...

  • Napoleon Fireplaces NPS40 - page 31

    W415-0616 / B / 02.18.08 31 # P ART NO . DESCRIPTION 1 W660-0052 LOW LIMIT SWITCH 140°F (80°C) 2 W660-0053 OVER-RIDE SWITCH 160°F (71°C) 3 W660-0054 IGNITION SWITCH 120°F (60°C) 4 W660-0055 HIGH LIMIT SWITCH 200°F (93°C) 5 W660-0056 V ACUUM SWITCH 6 W380-0020 CONTROL KNOB 7* W195-0004 POWER CORD 8 W435-0009 AUGER MOT OR 9 W062-0021 CONVECTI ...

  • Napoleon Fireplaces NPS40 - page 32

    W415-0616 / B / 02.18.08 32 COMMON REPLA CEMENTS P ARTS ...

  • Napoleon Fireplaces NPS40 - page 33

    W415-0616 / B / 02.18.08 33 NPS40 REPLA CEMENTS P ARTS 57 38 61 44 63 65 57 64 56 58 59 60 66 15 31 39 54 40 53 ...

  • Napoleon Fireplaces NPS40 - page 34

    W415-0616 / B / 02.18.08 34 NPI40 REPLA CEMENTS P ARTS ...

  • Napoleon Fireplaces NPS40 - page 35

    W415-0616 / B / 02.18.08 35 NPI40 A CCESSOR Y PA R T S COMMON A CCESSOR Y P ARTS ...

  • Napoleon Fireplaces NPS40 - page 36

    W415-0616 / B / 02.18.08 36 TR OUBLESHOO TING SYMPT OM TEST SOL UTION *NOTE: All troubleshooting procedures should be carried out by qualifi ed technicians or installers. The heater will not start Smoke in the room The exhaust blower is not operating The ignitor will not light the pellets however everything else in the heater operates The auger mo ...

  • Napoleon Fireplaces NPS40 - page 37

    W415-0616 / B / 02.18.08 37 TR OUBLESHOO TING CONTINUED SYMPT OM Feed rate dial has no effect on the fi re (timer control only) The convection blower is not functioning nor- mally The heater will not operate when hot TEST SOL UTION - Secure all connections to the power control module. - Perform a resistance test to the potentiometer by placing the ...

  • Napoleon Fireplaces NPS40 - page 38

    W415-0616 / B / 02.18.08 38 TR OUBLESHOO TING CONTINUED SYMPT OM TEST SOL UTION The 200°F (93°) high limit tem- perature sensor has tripped The heater will not turn off The heater keeps going out Excessive carbon build up in the fi rebox, low heat out put - Reset the sensor and determine whether it was the convection blower or 160°F (71°C) tem ...

  • Napoleon Fireplaces NPS40 - page 39

    W415-0616 / B / 02.18.08 39 SER VICE AND MAINTENANCE L OG Dealer's Name: Dealer's Address: City: State/Province: Zip Code/Postal Code: Serial Number: Date of Purchase: Date Installed: Notes: OWNERSHIP RECORDS SERVICE D A TE SER VICE TECHNICIAN SERVICE DESCRIPTION ...

  • Napoleon Fireplaces NPS40 - page 40

    W415-0616 / B / 02.18.08 40 NO TES ...

Manufacturer Napoleon Fireplaces Category Stove

Documents that we receive from a manufacturer of a Napoleon Fireplaces NPS40 can be divided into several groups. They are, among others:
- Napoleon Fireplaces technical drawings
- NPS40 manuals
- Napoleon Fireplaces product data sheets
- information booklets
- or energy labels Napoleon Fireplaces NPS40
All of them are important, but the most important information from the point of view of use of the device are in the user manual Napoleon Fireplaces NPS40.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Napoleon Fireplaces NPS40, service manual, brief instructions and user manuals Napoleon Fireplaces NPS40. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Napoleon Fireplaces NPS40.

Similar manuals

A complete manual for the device Napoleon Fireplaces NPS40, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Napoleon Fireplaces NPS40 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Napoleon Fireplaces NPS40.

A complete Napoleon Fireplaces manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Napoleon Fireplaces NPS40 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Napoleon Fireplaces NPS40, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Napoleon Fireplaces NPS40, that we can find in the current document
3. Tips how to use the basic functions of the device Napoleon Fireplaces NPS40 - which should help us in our first steps of using Napoleon Fireplaces NPS40
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Napoleon Fireplaces NPS40
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Napoleon Fireplaces NPS40 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Napoleon Fireplaces NPS40?

Use the form below

If you did not solve your problem by using a manual Napoleon Fireplaces NPS40, ask a question using the form below. If a user had a similar problem with Napoleon Fireplaces NPS40 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)