English dropdown-ico

Manual JVC RM-P2580

32 pages 1.12 mb
Download

Go to site of 32

Summary
  • JVC RM-P2580 - page 1

    INSTRUCTIONS REMOTE CONTROL UNIT RM-P2580 For Customer Use: Enter below the Model No. and Serial No. which is located on the body. Retain this information for future reference. Model No. RM-P2580 Serial No. SC96858-001 R INTRODUCTION BASIC OPERA TIONS APPLIED OPERA TIONS O THER CONNECTIONS MENU SCREEN SETUPS ...

  • JVC RM-P2580 - page 2

    2 CA UTION RISK OF ELECTRIC SHOCK DO NOT OPEN CA UTION : T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMO VE CO VER (OR BACK). NO USER SER VICEABLE P ARTS INSIDE. REFER SER VICING T O QU ALIFIED SERVICE PERSONNEL. Information f or USA This de vice complies with Part 15 of the FCC Rules. Changes or modifications not approv ed b y JVC could void th ...

  • JVC RM-P2580 - page 3

    3 1. INTRODUCTION ● CONTENTS .......................................................................................................................................... 3 ● FEA TURES ........................................................................................................................................... 4 ● ACCESSORIES ...... ...

  • JVC RM-P2580 - page 4

    4 䢇 Presetting of up to 64 positions (including the home positions) each, for up to 8 combination camer as (TK-C675B). 䢇 Built-in P AN, TIL T and ZOOM control for up to 8 camer as. 䢇 RS-485 connection system enables cascaded connection of cameras . 䢇 Built-in sequential switcher . 䢇 Alarm input ter minals. 䢇 Data I/O terminals for inter ...

  • JVC RM-P2580 - page 5

    5 1 [MENU] button (with an indicator) When this button is pressed, the MONIT OR OUTPUT 1 ‚ on the rear panel outputs a menu screen and the indi- cator with this button lights up . REF . : “MENU SCREEN SETUP” on page 25. 2 [SET] button ● While a nor mal screen is display ed (i.e. when a menu screen is not displa yed), pressing and holding th ...

  • JVC RM-P2580 - page 6

    6 8 [A UTO] b utton When this button is pressed, the unit enters the A UT O SE- QUENCE mode, in which the indicator lights up and the MONIT OR OUTPUT 1 connector ‚ on the rear panel out- put the camera video signals according to automatic s witch- ing. REF . : “A UTO SEQ UENCE OPERA TION” on page 13. 9 [F1, F2, F3] Function buttons These butt ...

  • JVC RM-P2580 - page 7

    7 The A UT O P A TROL function can be set on a per-camera basis. REF . : “A UTO P A TROL OPERA TION” on page 15. % [–, +] Negative and positive b uttons Press button to decrease or increase the camera or posi- tion number . ^ [A UTO P AN] button Press this button to rotate or s wing a camera between pre- set positions at a preset time inter v ...

  • JVC RM-P2580 - page 8

    8 › [A C ` INPUT] A C power input connector Connect to a conv entional 120 V AC power supply using the provided pow er cord. fi [PO WER] s witch T urns the power of the unit ON and OFF . When this switch is set to ON, the POWER indicator 4 on the front panel lights up . fl [T O CAMERA] Camera control signal connectors Connection ter minals f or ...

  • JVC RM-P2580 - page 9

    9 2. BASIC OPERA TIONS Manual Operation Camera Selection ( REF . :P age 10) Switching to the selected camera video . P an/Tilt Operation ( REF . : P age 12) (TIL T) Tilts the camera up and down, (P AN) P ans the camera in the left and right directions. P osition Selection ( REF . : P age 11) Switching the camera to the selected video position. Oper ...

  • JVC RM-P2580 - page 10

    10 Selecting a Desired Camera 2. BASIC OPERA TIONS CAMERA SELECTION 1. Press the CAMERA button so that the indicator lights up . 2. Input the camera number using the numeric k eys (0 to 9). The input figure is shown in the CAMERA display together with a period after it. (Example: When “8” is input) T o clear the input figure , press the CLEAR b ...

  • JVC RM-P2580 - page 11

    11 Selecting a Desired Preset P osition ( REF . : P age 27 for the position presetting.) 2. BASIC OPERA TIONS POSITION SELECTION 1. Press the POSITION button so that the indicator lights up . 2. Input the position number using the numeric ke ys (0 to 9). The input figure is shown in the POSITION displa y to- gether with a period after it. (Example: ...

  • JVC RM-P2580 - page 12

    12 The manual operation allo ws y ou to P AN or TIL T the selected camera and to control its lens. 2. BASIC OPERA TIONS MANU AL OPERA TION NO TES ● Manual operation is not a v ailable in the A UT O SEQUENCE or A UTO P A TR OL modes. ● Only the le ver tilting oper ation is av ailable in the A UT O P AN mode . Operating the P AN/TIL T Contr ol Le ...

  • JVC RM-P2580 - page 13

    13 A UT O SEQUENCE OPERA TION Operation with the Basic System ( REF . : P age 32 f or the s witching inter val setting.) When the A UTO b utton is pressed, the A UTO indicator lights up and the MONIT OR OUTPUT connectors output the camera images, s witching them in order of camera numbers at constant intervals . (Example) When using cameras 1 to 6 ...

  • JVC RM-P2580 - page 14

    14 The A UTO P AN operation consists of low-speed horizontal mo vement of a camera between preset positions at a constant time interval. A utomatic panning is set between 2 points. This function can be set on individual cameras. 2. BASIC OPERA TIONS A UT O P AN OPERA TION 1. Press the A UTO P AN button. The LED indicator lights up and the A UT O P ...

  • JVC RM-P2580 - page 15

    15 2. BASIC OPERA TIONS A UT O P A TROL OPERA TION The A UTO P A TROL operation consists of high-speed camera mo vement between multiple pre-set positions, in a sequence and at time intervals set b y the user . This function can be set on individual cameras. 1. Press the A UT O P A TROL b utton. The LED indicator lights up and the A UT O P A TROL o ...

  • JVC RM-P2580 - page 16

    16 2. BASIC OPERA TIONS KEY LOCK (PREVENTION OF OPERA TION MIST AKE) The KEY LOCK function helps prevent operational mistakes b y inhibiting the functions of all the b uttons and the jo ystick on the contr ol panel. 1. Press and hold the SET button f or more than 3 seconds to put the unit into KEY LOCK status. The KEY LOCK indicator lights up , and ...

  • JVC RM-P2580 - page 17

    17 When an alar m signal is receiv ed, this unit performs the f ollowing oper ations. <Alarm priority mode> ● The video is s witched to the camera position from which the alarm signal is received. ● An alarm signal will automatically override and cancel the operation of either A UTO P A TROL or A UTO SEQUENCE. (A UTO SEQUENCE: In A mode o ...

  • JVC RM-P2580 - page 18

    18 CAMERA SWITCHING OPERA TION D A T A OUTPUT 3. APPLIED OPERA TIONS ALARM OPERA TION (Continued) Clearing the alarm The alarm operation can be cleared in tw o ways: 1 TO CAMERA TO CAMERA DATA I / O DATA I / O RX + RX - TX + TX - COM COM 1 2 3 4 5 6 7 8 COM COM 9/1 9/1 10/2 10/2 11/3 11/3 12/4 12/4 13/5 13/5 14/6 14/6 15/7 15/7 16/8 16/8 COM COM CO ...

  • JVC RM-P2580 - page 19

    19 1 TO CAMERA TO CAMERA DATA I / O DATA I / O RX RX + RX RX - TX TX + TX TX - COM COM 1 2 3 4 5 6 7 8 COM COM 9/1 9/1 10/2 10/2 11/3 11/3 12/4 12/4 13/5 13/5 14/6 14/6 15/7 15/7 16/8 16/8 COM COM COM COM COM COM CAMERA CAMERA SW SW UNIT UNIT ALARM ALARM AUTO AUTO 4 3 1 2 8 7 5 6 2 3 4 5 6 7 8 1 MONITOR MONITOR OUTPUT OUTPUT MONITOR MONITOR SERIAL- ...

  • JVC RM-P2580 - page 20

    20 A MODE T erminal Name AU T O I/O 1 to 8 (I/O 9/ to 16/8) UNIT ALARM CAMERA SW Condition — When 8 SEL OUT is set • I/O 1 to 8 correspond to cameras 1 to 8. When 8 ALM OUT is set • I/O 1 to 8 corresponds to cameras 1 to 8. — — Signals The MAKE signal is output for betw een 500 ms and 1000 ms duration in the follo wing cases. ● P ower O ...

  • JVC RM-P2580 - page 21

    21 V .IN V .IN 34 2 1 MONIT OR B OUTPUT CAM SW OUT VIDEO INPUT CAM IN MONIT OR-A OUTPUT VCR OUTPUT RS-232C MASTER MONITOR MONITOR TIMELAPSE VCR CAMERA 1 CAMERA 2 CAMERA 3 ID:1 ID:2 ID:3 5 6 7 8 1 TO CAMERA TO CAMERA DATA I / O DATA I / O RX RX + RX RX - TX TX + TX TX - COM COM 1 2 3 4 5 6 7 8 COM COM 9/1 9/1 10/2 10/2 11/3 11/3 12/4 12/4 13/5 13/5 ...

  • JVC RM-P2580 - page 22

    22 T erminal Name AU T O I/O 1 to 8 UNIT ALARM CAMERA SW Condition — When 8 SEL OUT is set • I/O 1 to 8 correspond to cameras 1 to 8. When 16 SEL OUT is set • I/O 1 to 16 correspond to cameras 1 to 16. 8ALM OUT • I/O 1 to 8 correspond to cameras 1 to 8. 16ALM OUT • I/O 1 to 16 correspond to cameras 1 to 16. — — B MODE Signals The MAKE ...

  • JVC RM-P2580 - page 23

    23 The electrical standards applied to the SERIAL-1 and SERIAL- 2 connectors can be s witched between RS-232C and RS-422A using pins 7 and 8 of the rear panel DIP s witch. 4. CONNECTIONS REAR P ANEL CONNECT ORS T O CAMERA Connection to control the camera. (The RM-P2580 is compatible with a TK-C675B camera.) Communication is carried out by MUL TIDRO ...

  • JVC RM-P2580 - page 24

    24 4. CONNECTIONS REAR P ANEL CONNECT ORS (Continued) D A T A I/O 䡵 ALARM INPUTS 1 to 16 TTL lev el (Make/Break), input duration 70 ms or more. REF . : “CONTROL UNIT SCREEN” on page 28 and “POLARITY item of D A T A I/O SCREEN (INPUT ASSIGNMENT SCREEN)” on page 31 for the Make/ Break s witching. 䡵 ALARM/SELECT OUTPUTS 1 to 16 Alar m or s ...

  • JVC RM-P2580 - page 25

    25 5. MENU SCREEN SETUPS FLO W OF MENUS POSITION SETUP SET UP screen CAMERA CONTROL UNIT screen ( REF . : Page 28) POSITION SETUP screen ( REF . : Page 27) CAMERA screen ( REF . : Page 28) OPTION screen ( REF . : Page 29) MAX CAMERA (Displayed at B Mode only) P/T SPEED SERIAL-2 (Displayed at B Mode only) CAMERA SELECTION (Displayed at A Mode only) ...

  • JVC RM-P2580 - page 26

    26 MENU OPERA TION 5. MENU SCREEN SETUPS 1. Set the POWER s witch on the rear panel to “ON”. 2. Press and hold the MENU button f or about 3 seconds. The LED indicator lights up and the MONIT OR OUTPUT 1 connector on the rear panel outputs the SETUP screen signal. 3. Select a menu item by mo ving the cursor (>) using the P AN/TIL T control le ...

  • JVC RM-P2580 - page 27

    27 1. Press and hold the MENU button f or about 3 seconds to display the SETUP screen. 2. Select POSITION SETUP and press the SET button. “– POSITION SETUP MODE –” with the currently selected Camera No . and the P osition No. are displa yed. ("C01 - P05" shows the Camera 1, P osition 5.) 3. Select a camera number . CAMERA button ? ...

  • JVC RM-P2580 - page 28

    28 1. Press and hold the MENU button f or about 3 seconds to display the SETUP screen. 2. Select CAMERA and press the SET button. The menu screen for the connected camer as is displa yed. 5. MENU SCREEN SETUPS CAMERA SCREEN T o set up the connected cameras, please refer to the instruction man uals of the individual cameras. Use the follo wing pr oc ...

  • JVC RM-P2580 - page 29

    32 Item PRIORITY ALARM TIME BUZZER TIME Function Sets whether an alar m input is accepted during manual opera- tion. ALARM : Alar m input is accepted e ven during manual opera- tion. MANU AL : Alar m input is not accepted during manual opera- tion. Sets how long the alarm operation will continue after an alarm input. Sets the buzz er sound generate ...

  • JVC RM-P2580 - page 30

    33 6. OTHER TROUBLESHOO TING Check • Is the power supply connected properly to all off the camer as? • Are the cameras connected properly to the VIDEO INPUT connectors? • Are the camera heads compatib le with this unit? • Preset their home positions. • Are the cameras connected properly to the TO CAMERA connectors? • Are the DIP s witch ...

  • JVC RM-P2580 - page 31

    34 6. OTHER SPECIFICA TIONS Applicable camer as : TK-C675B Max. number of connected camer as : 8 (A mode), 16(B mode) Max. cable length : 1.2 km Control terminals : Push ter minals (RS-485) 9600 bps. Max. number of DA T A I/O terminals :1 6 Max. number of alarm inputs/outputs :1 6 Number of UNIT ALARM outputs : 1 line (open-collector) Number of A U ...

  • JVC RM-P2580 - page 32

    32 Item PRIORITY ALARM TIME BUZZER TIME Function Sets whether an alar m input is accepted during manual opera- tion. ALARM : Alar m input is accepted e ven during manual opera- tion. MANU AL : Alar m input is not accepted during manual opera- tion. Sets how long the alarm operation will continue after an alarm input. Sets the buzz er sound generate ...

Manufacturer JVC Category Camera Accessories

Documents that we receive from a manufacturer of a JVC RM-P2580 can be divided into several groups. They are, among others:
- JVC technical drawings
- RM-P2580 manuals
- JVC product data sheets
- information booklets
- or energy labels JVC RM-P2580
All of them are important, but the most important information from the point of view of use of the device are in the user manual JVC RM-P2580.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JVC RM-P2580, service manual, brief instructions and user manuals JVC RM-P2580. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JVC RM-P2580.

Similar manuals

A complete manual for the device JVC RM-P2580, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JVC RM-P2580 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JVC RM-P2580.

A complete JVC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JVC RM-P2580 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JVC RM-P2580, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JVC RM-P2580, that we can find in the current document
3. Tips how to use the basic functions of the device JVC RM-P2580 - which should help us in our first steps of using JVC RM-P2580
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JVC RM-P2580
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JVC RM-P2580 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JVC RM-P2580?

Use the form below

If you did not solve your problem by using a manual JVC RM-P2580, ask a question using the form below. If a user had a similar problem with JVC RM-P2580 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)