English dropdown-ico

Manual Cleveland Range KEL-40

29 pages 1.55 mb
Download

Go to site of 29

Summary
  • Cleveland Range KEL-40 - page 1

    1333 East 179th S t., Cleveland, Ohio, U.S.A. 441 10 Phone: (216) 481-4900 Fax: (216) 481-3782 Visit our web site at www .clevelandrange.com SE95036 Rev . 6 Operators Manual Installation, Operation & Service Electric Floor Model Kettles For units built after August 1999 MODELS : KEL-25, KEL-30, KEL-40, KEL-40-SH, KEL-60, KEL-80, KEL-100 KEL-25- ...

  • Cleveland Range KEL-40 - page 2

    Shut off pow er at main fuse disconnect prior to ser vicing. Ensure kettle is at room temperature and pressure gauge is showing z ero or less prior to removing any fittings . Inspect unit daily f or proper operation. 0 Do not fill kettle abo v e recommended le v el marked on outside of k ettle. Surf aces ma y be e xtremely hot! Use protectiv e equi ...

  • Cleveland Range KEL-40 - page 3

    GENERAL Installation of the kettle must be accomplished by qualified electrical installation personnel working to all applicable local and national codes. Improper installation of pr oduct could cause injury or damage. This equipment is built to comply with applicable standards for manufactur ers. Included among those approval agencies ar e: UL, NS ...

  • Cleveland Range KEL-40 - page 4

    RECOMMENDED FLOOR DRAIN DET AIL ASSEMBL Y Position the kettle in it's permanent location, and level the kettle by turning the adjustable flanged feet. Once positioned and leveled, permanently secure the kettle's flanged feet to the floor using 5/16" lag bolts and floor anchors (supplied by the installer). There ar e three bolts r equ ...

  • Cleveland Range KEL-40 - page 5

    INST ALLA TION CHECKS Although the kettle has been thoroughly tested before leaving the factory , the installer is responsible for ensuring the pr oper operation of kettle once installed. Visual Checks 1. Check Tilting (tilting kettles): A / Gearbox tilts kettle smoothly and freely . 2. Insure ther e are: A / Three lag bolts secur ely holding each ...

  • Cleveland Range KEL-40 - page 6

    OPERA TING INSTRUCTIONS General Parts Drawing ITEM # DESCRIPTION FUNCTION 1. On-Off Switch/Solid State T urns kettle ON/OFF and allows the operator to adjust the kettle T emperature Control temperature in incr ements from 1 (Min.) to 10 (Max.). (see T emperature Range Chart in the Operating Instructions section). 2. Heat Indicator Light (Green) Whe ...

  • Cleveland Range KEL-40 - page 7

    OPERA TING THE KETTLE DO NOT LEAN ON OR PLACE OBJECTS ON KETTLE LIP . SERIOUS INJUR Y COULD RESUL T IF KETTLE TIPPED OVER, SPILLING HOT CONTENTS. 1. Before turning kettle on, read the V acuum/Pressure Gauge ( 4 ). The gauges needle should be in the green zone. Once heated, the kettle's normal maximum operating pressur e is approximately 1 0 -1 ...

  • Cleveland Range KEL-40 - page 8

    CARE AND CLEANING Cooking equipment must be cleaned regularly to maintain its fast, efficient cooking performance and to ensure its continued safe, r eliable operation. The best time to clean is shortly after each use (allow unit to cool to a safe temperature). W ARNINGS ➩ Do not use detergents or cleansers that are chloride based or contain quat ...

  • Cleveland Range KEL-40 - page 9

    ST AINLESS STEEL EQUIPMENT CARE AND CLEANING (Suppied courtesy of Nafem. For more information visit their web site at www .nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. Corrosion on metals is everywhere. It is r ecognized quickly on iron and steel as unsightly yellow/orange rust. Such metals are called “activ ...

  • Cleveland Range KEL-40 - page 10

    F AUCET ASSEMBL Y ITEM P ART DESCRIPTION QTY . NO. NO. 1. KE50825-5 3/4" Spout . . . . . . . . . . . . . . . . . . . . . .1 (KEL-25/30/40/60/80/100 & 40-SH) KE50825-3 3/4" Spout (KEL-25-T) . . . . . . . . . . . . .1 KE50825-2 3/4" Spout (KEL-40/60/80/100-T) . . . .1 2. F A95022 Retaining Ring . . . . . . . . . . . . . . . . . .1 ...

  • Cleveland Range KEL-40 - page 11

    HINGE ASSEMBL Y 1 5 3 2 13 12 6 4 7 11 8 10 9 9 ITEM NO . P AR T NO . DESCRIPTION QTY . Hinge Assembly 1. - 11 KE50597-1 25 - 40 Gallon, 20 Gallon Full Jacketed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE50597-2 60 - 80 Gallon, 30 - 40 Gallon Full Jacketed . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE50597-3 100 - ...

  • Cleveland Range KEL-40 - page 12

    ITEM NO. P ART NO. DESCRIPTION QTY . 1. KE50556-1 Probe, Water Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE54941-5 Safety V alve, 50 PSI, 1/2" (Nor th America) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KE54941-31 Safety V alve, 50 PSI, 1/2", (Europe) . . . . . ...

  • Cleveland Range KEL-40 - page 13

    11. KE000714-4 Pr essure Gauge, for units built prior to Februar y 2005 . . . . . . . . . . . . . . . . . . .1 KE50429-5 Pressure Gauge, for units built after January 2005 . . . . . . . . . . . . . . . . . . . . . .1 12. SE003013-1 L.E.D., Red, Replacement Kit., (includes LED & "O" Ring) . . . . . . . . . . . . . . . .1 SE003013-2 L.E ...

  • Cleveland Range KEL-40 - page 14

    CONTROL CONSOLE COMPONENTS - HAND TIL T 44 45 4 3 ...

  • Cleveland Range KEL-40 - page 15

    CONTROL CONSOLE COMPONENTS - HAND TIL T ITEM NO. P ART NO. DESCRIPTION QTY . 1. F A11134 Screw , 10-24 x 3/8" SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 2. KE50325 Gear Box Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. F A95008 Lo ...

  • Cleveland Range KEL-40 - page 16

    CONTROL CONSOLE COMPONENTS - POWER TIL T 41 42 40 44 45 4 3 ...

  • Cleveland Range KEL-40 - page 17

    CONTROL CONSOLE COMPONENTS - POWER TIL T ITEM NO. P ART NO. DESCRIPTION QTY . 1. KE503252 Gear Box Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. F A11134 Scr ew , 10-24 x 3/8" S.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE52832- ...

  • Cleveland Range KEL-40 - page 18

    TRUNNION ASSEMBL Y ITEM P ART DESCRIPTION QTY . NO. NO. 1. KE00354 TRUNNION BEARING ASSEMBL Y . . . . . .1 (INCLUDES P ART # 3 & 6) 2. KE00351 TRUNNION BEARING ASSEMBL Y . . . . . .1 (INCLUDES P ART # 3 & 6) 3. KE51711 ROLLER BEARING . . . . . . . . . . . . . . . . . 2 4. KE51571-1 SPHERICAL WASHER . . . . . . . . . . . . . . . .1 5. F A950 ...

  • Cleveland Range KEL-40 - page 19

    SP ARE P AR TS LIST ITEM ON. DESCRIPTION QTY . QTY . DOMESTIC OVERSEAS Refer to Kettle Bottom & Side for p art s drawing KE00458 Solid State Control Box 1 1 KE50753-7 Relay , 12 VDC 1 KE50750-5 Contactor , 208/240V , 60 Amp. 1 2 (special high wattage kettles - 6 elements) KE53838-11 T ransformer , 380-415 to 120-220V 1 SE00115 Potentiometer wit ...

  • Cleveland Range KEL-40 - page 20

    Cleveland Range equipment requir es little preventative maintenance. W e do however provide the following chart as a guideline for inspection and maintenance to keep your unit functioning at 100%. INSPECTION AND MAINTENANCE CHECK LIST The following check should be completed every six months or more frequently if unit is in a high volume facility . ...

  • Cleveland Range KEL-40 - page 21

    CALIBRA TING PROCEDURE 1. Insure the unit has a vacuum befor e you begin calibrating procedur es. If unit requir es venting refer to Kettle V enting Instructions. 2. Set On-Off Switch/T emperature Contr ol to " 10 " ( Max.). 3. Allow the unit to cycle twice. 4. Check temperature of the inner kettle surface with a digital surface ther mome ...

  • Cleveland Range KEL-40 - page 22

    3. Pull Pressur e Relief V alve (A) open to insur e vessel is not pressurized. 4. Remove Pressur e Relief V alve (A). 5. Replace Pressur e Relief V alve (A) with Str eet Elbow (B). 6. Add distilled water (C) through the Str eet Elbow (B), using a funnel if necessary . Refer to Distilled Water Requirements chart for the proper amount requir ed. 7. A ...

  • Cleveland Range KEL-40 - page 23

    LUBRICA TION PROCEDURE Lubricate the following parts ever y three months to insure smooth operation and r educe wear . TRUNNION HOUSING , WORM SCREW AND TIL T GEAR These parts are accessed through the top cover of the console. Apply grease to gear teeth. Check for excessive play and adjust with adjusting screw located on top of cross bar . KETTLE T ...

  • Cleveland Range KEL-40 - page 24

    KETTLE JACKET CLEANOUT AND P ASSIV A TION PROCEDURES The following procedur e should be preformed at least once every three years to prevent possible corr osion and ensure the optimum life of the kettle. DESCRIPTION - Molyfilm 315 inhibits corrosion in stainless steel and copper . A pH buffer is pr esent to assist in maintaining the appropriate pH ...

  • Cleveland Range KEL-40 - page 25

    Fault Isolation Pr ocedur e Step T est 1. Is there pr oper incoming voltage at terminal block? 2. Is the red LED illuminated? 3. Is the green LED illuminated? 4. Do both contactors energize? 5. Measure continuity acr oss safety thermostat. Is it an open circuit? 6. Is there 120 V AC present across the coils of the contactors? 7. Remove wire fr om l ...

  • Cleveland Range KEL-40 - page 26

    Fault Isolation Pr ocedur e Step T est 1. In a cold state, does the pressur e gauge read in the gr een zone? 2. Do the contactors shut off too early? (before r eaching normal maximum operating pressur e.) 3. Does the green LED r emain illuminated after the contactors shut off? 4. Unplug control box and measur e the resistance acr oss potentiometer ...

  • Cleveland Range KEL-40 - page 27

    5. Remove kettle thermistor and allow to cool. Remove edge connector from control box. T est r esistance across edge connector's pins #2 and #7. Is it approximately 100,000 ohms? 6. T ur n the potentiometer on the control box clockwise to increase the maximum operating temperature. Does the kettle now achieve maximum operating pressur e of 30- ...

  • Cleveland Range KEL-40 - page 28

    WIRING DIAGRAM 200-240v OUTSIDE OF NORTH AMERICA LIMIT ...

  • Cleveland Range KEL-40 - page 29

    WIRING DIAGRAM 380-600v OUTSIDE OF NORTH AMERICA LIMIT ...

Manufacturer Cleveland Range Category Hot Beverage Maker

Documents that we receive from a manufacturer of a Cleveland Range KEL-40 can be divided into several groups. They are, among others:
- Cleveland Range technical drawings
- KEL-40 manuals
- Cleveland Range product data sheets
- information booklets
- or energy labels Cleveland Range KEL-40
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cleveland Range KEL-40.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cleveland Range KEL-40, service manual, brief instructions and user manuals Cleveland Range KEL-40. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cleveland Range KEL-40.

Similar manuals

A complete manual for the device Cleveland Range KEL-40, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cleveland Range KEL-40 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cleveland Range KEL-40.

A complete Cleveland Range manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cleveland Range KEL-40 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cleveland Range KEL-40, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cleveland Range KEL-40, that we can find in the current document
3. Tips how to use the basic functions of the device Cleveland Range KEL-40 - which should help us in our first steps of using Cleveland Range KEL-40
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cleveland Range KEL-40
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cleveland Range KEL-40 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cleveland Range KEL-40?

Use the form below

If you did not solve your problem by using a manual Cleveland Range KEL-40, ask a question using the form below. If a user had a similar problem with Cleveland Range KEL-40 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)