English dropdown-ico

Manual Jeep Liberty (2005)

424 pages 11.56 mb
Download

Go to site of 424

Summary
  • Jeep Liberty (2005) - page 1

    T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................. 1 1 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 7 7 4 UNDERST ANDING YOUR INSTRUMENT P ANEL .................................. ...

  • Jeep Liberty (2005) - page 2

    ...

  • Jeep Liberty (2005) - page 3

    INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 ▫ Roll Over W arning ..................... 5 䡵 How T o Use This Manual .................. 7 䡵 W arnings And Cautions ................... 7 䡵 V ehicle Identification Number ............... 8 䡵 V ehicle Modifications / Alterations ........... 9 1 ...

  • Jeep Liberty (2005) - page 4

    INTRODUCTION Thank you for selecting a Jeep 威 Liberty and welcome to our worldwide family . This is a specialized utility vehicle designed for both on-road and of f-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However , on-road ride and handling will have a differ ent feel from wh ...

  • Jeep Liberty (2005) - page 5

    Roll Over W arning Utility vehicles have a significantly higher roll over rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity , and narrower track than many passenger cars. It is capable of perform- ing better in a wide variety of off-r oad applications. Driven in an unsafe manner , all vehicles c ...

  • Jeep Liberty (2005) - page 6

    Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury . In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year , and could reduce disabling injuries by 2 million annually . In a roll over crash an unbelted person is si ...

  • Jeep Liberty (2005) - page 7

    W ARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contain or emit chemicals known to the State of Califor ...

  • Jeep Liberty (2005) - page 8

    VEHICLE IDENTIFICA TION NUMBER The vehicle identification number (VIN) is located on a stamped plate on the bottom of the left front A-Pillar , visible from outside of the vehicle thr ough the wind- shield. This number also appears on the Automobile Information Disclosure Label af fixed to a window on your vehicle. Save this label for a convenient ...

  • Jeep Liberty (2005) - page 9

    VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. INTRODUCTION 9 1 ...

  • Jeep Liberty (2005) - page 10

    ...

  • Jeep Liberty (2005) - page 11

    THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 4 ▫ Ignition Key .......................... 1 4 ▫ Key-In-Ignition Reminder ................ 1 6 䡵 Sentry Key Immobilizer System .............. 1 6 ▫ Important Note About Service ............. 1 7 ▫ Replacement Keys .................... ...

  • Jeep Liberty (2005) - page 12

    ▫ T o Unlock The Doors ................... 2 5 ▫ T o Lock The Doors ..................... 2 6 ▫ T o Unlatch The Swing Gate Flip-Up W indow . .26 ▫ Panic Alarm .......................... 2 7 ▫ T o Use The Panic Alarm ................. 2 7 ▫ T o Program Additional T ransmitters ......... 2 8 ▫ General Information .................... 2 ...

  • Jeep Liberty (2005) - page 13

    ▫ Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags .......... 4 8 ▫ Child Restraint ........................ 6 3 䡵 Engine Break-In Recommendations ........... 7 3 䡵 Safety T ips ............................ 7 3 ▫ Exhaust Gas .......................... 7 3 ▫ Safety Checks Y ou Should Make Inside The V ehicle .. ...

  • Jeep Liberty (2005) - page 14

    A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number . The key code can also be obtained by the dealer from your vehicle invoice. Ignition Key Insert the key fully , then turn the switch to one of the four ...

  • Jeep Liberty (2005) - page 15

    T o remove the ignition key on models with a manual transmission, depress and hold the key r elease button, turn the ignition key to LOCK and remove the key . W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake ...

  • Jeep Liberty (2005) - page 16

    Key-In-Ignition Reminder If you open the driver’s door and the key is fully inserted in the ignition switch, a chime will sound to remind you to remove the key . SENTR Y KEY IMMOBILIZER SYSTEM The Sentry Key Immobilizer System (SKIS) prevents unauthorized operation of the vehicle by disabling the engine. The system will shut the engine down after ...

  • Jeep Liberty (2005) - page 17

    NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting pr oblems and loss of security protection. • Mobil Speedpass™, additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (T ransponder) fault ...

  • Jeep Liberty (2005) - page 18

    consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer . Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1. Cut the additional Sentry ...

  • Jeep Liberty (2005) - page 19

    2. This device must accept any interfer ence that may be received, including interfer ence that may cause undes- ired operation. STEERING WHEEL LOCK — IF EQUIPPED Y our vehicle may be equipped with a passive steering wheel lock (manual transmission only). This lock pre- vents steering the vehicle without the ignition key . If the steering wheel i ...

  • Jeep Liberty (2005) - page 20

    DOORS AND DOOR LOCKS The vacuum fluorescent (VF) display located in the odometer area displays the wor d “door” as an indication of a door ajar or door not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the VF display will show the word “door” and then show the odometer/trip odometer mileage ...

  • Jeep Liberty (2005) - page 21

    chime for each complete display cycle (three cycles total). After this, the display will continue to cycle only (no chimes). If the trip/reset button is pr essed while the VF warnings are being displayed, the VF display will r evert back to only displaying the odometer/trip odometer mileage. Manual Door Locks Use the manual door lock plunger to loc ...

  • Jeep Liberty (2005) - page 22

    W ARNING! • For personal security , and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Un ...

  • Jeep Liberty (2005) - page 23

    Power Door Locks — If Equipped A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Therefor e, make sure the keys ar e not inside the vehicle before closing the door . If you press the door lock switch while the keys ar e in the ignition ...

  • Jeep Liberty (2005) - page 24

    Child Protection Locks The rear doors of your vehicle ar e equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks. W ARNING! A void trapping anyone in the vehicle in a collision. Remember that the r ...

  • Jeep Liberty (2005) - page 25

    REMOTE KEYLESS ENTR Y This system allows you to lock or unlock the doors or open the swing gate flip-up window from distances of 23–50 feet (7–15 meters) using a transmitter . Y ou don’t have to point the transmitter at the vehicle to activate the system. Each vehicle comes with two transmitters. T o Unlock the Doors Press and r elease the ? ...

  • Jeep Liberty (2005) - page 26

    4. Repeating steps 1–3 will r estore original operation. NOTE: The Light Flash can be enabled or disabled (within 23–50 feet (7–15 meters) of the vehicle) by per- forming the following procedur e: 1. Pr ess and hold the ⬙ Lock ⬙ button on the transmitter . 2. Continue to hold the ⬙ Lock ⬙ button, wait at least 4 but no longer than 10 ...

  • Jeep Liberty (2005) - page 27

    W ARNING! T o avoid injury stand back when opening. Glass will automatically rise. NOTE: The transmitter can be programmed to unlatch the flip-up window immediately upon activation of the “Rear Release” button (without pressing and holding) (within 23–50 feet (7–15 meters) of the vehicle) by per- forming the following procedur e: 1. Pr ess ...

  • Jeep Liberty (2005) - page 28

    T o Program Additional T ransmitters NOTE: If vehicle is equipped with the optional Elec- tronic V ehicle Information Center (EVIC) in the overhead console, the transmitters may also be programmed through the EVIC display . For additional information, refer to “Over head Console — If Equipped” in Section 3. Up to 4 transmitters can be program ...

  • Jeep Liberty (2005) - page 29

    2. This device must accept any interfer ence that may be received, including interfer ence that may cause undes- ired operation. If your Remote Keyless Entry fails to operate from a normal distance, check for these two conditions: 1. W eak batteries in transmitter . The expected life of batteries is from one to two years 2. Closeness to a radio tra ...

  • Jeep Liberty (2005) - page 30

    SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors, swing gate, swing gate flip-up window , and ignition for unautho- rized operation. When the alarm is activated, the system provides both audible and visual signals. The horn, headlights, and tail lights will sound/flash repeatedly for three minutes. If disturbance is stil ...

  • Jeep Liberty (2005) - page 31

    T o Disarm the System T o disarm the system, you will need to press the “Un- lock” button on the remote keyless entry transmitter or turn the ignition key to the RUN position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering. NOTE: On vehicles equip ...

  • Jeep Liberty (2005) - page 32

    T o open the swing gate, pull the gate handle to its first detent to open just the flip-up window . Pull the handle to its second detent (all the way) to open both the flip-up window and swing gate. W ARNING! T o avoid injury stand back when opening. Glass will automatically rise. The vacuum fluorescent (VF) display located in the odometer area dis ...

  • Jeep Liberty (2005) - page 33

    EVIC display (not in the instrument cluster). For addi- tional information, refer to “Over head Console — If Equipped” in Section 3. If any other active warnings including “door” or “LO- W ASH” are pr esent, they will be shown in the VF display and will also continue to cycle. If the vehicle is moving, two single chimes will occur if ...

  • Jeep Liberty (2005) - page 34

    open (one chime for each complete display cycle). After this, the VF display will continue to sequence only (no chimes). If the trip/reset button is pr essed while the VF warnings are being displayed, the VF display will r evert back to only displaying the odometer/trip odometer mileage. NOTE: Close swing gate before flip-up window . CAUTION! Do no ...

  • Jeep Liberty (2005) - page 35

    WINDOWS Power Windows — If Equipped The power window switches are located on the center floor console. The top left switch controls the left fr ont window and the top right switch controls the right fr ont window . The lower left switch controls the left r ear passenger window , and the lower right switch controls the right rear passenger window ...

  • Jeep Liberty (2005) - page 36

    Auto Down Feature — If Equipped The driver’s and passenger’s front window switches have an auto down feature. Pr ess the window switch past the detent, release, and the window will go down auto- matically . T o open the window part way , press the window switch part way and release it when you want the window to stop. Rear Passenger W indow S ...

  • Jeep Liberty (2005) - page 37

    windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buf feting occurs with the sunroof open, adjust the sunr oof opening to minimize the buffeting. OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. ...

  • Jeep Liberty (2005) - page 38

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thr own from the vehicle. Seat belts r educe the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at ...

  • Jeep Liberty (2005) - page 39

    Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. Latch Plate THINGS TO KNOW BEFORE ST ...

  • Jeep Liberty (2005) - page 40

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is ...

  • Jeep Liberty (2005) - page 41

    4. Position the lap belt acr oss your thighs, below your abdomen. T o remove slack in the lap portion, pull up a bit on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. NOTE: The “Seat Belt Indicator Light” will re ...

  • Jeep Liberty (2005) - page 42

    W ARNING! A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. A twisted belt cannot do its job as well. In a collision it could even cut into you. Be sure the ...

  • Jeep Liberty (2005) - page 43

    Adjustable Upper Shoulder Belt Anchorage In the front seat positions, the shoulder belt can be adjusted upward or downwar d to position the belt away from your neck. T o lower the shoulder belt height, push the button and slide the height adjuster down. T o raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height ...

  • Jeep Liberty (2005) - page 44

    W ARNING! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e ta ...

  • Jeep Liberty (2005) - page 45

    Energy Management Feature This vehicle has a safety belt system with an energy management feature at the driver and fr ont passenger seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to pay out webbing in a controlled manner . This featu ...

  • Jeep Liberty (2005) - page 46

    Seat Belt Pretensioners The driver and front passenger seat belts ar e equipped with a pretensioning device that is designed to r emove any slack from the seat belt systems in the event of a collision. This device improves the performance of the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners wor ...

  • Jeep Liberty (2005) - page 47

    The Enhanced W arning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or ST AR T position. The manufacturer does not r ecom- mend deactivating the Enhanced W arning System (BeltAlert). ...

  • Jeep Liberty (2005) - page 48

    Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender . This extender should be used only if the existing belt is not long enough. When it is not requir ed, remove the ex- ...

  • Jeep Liberty (2005) - page 49

    the instrument panel, above the glove compartment. The words SRS/AIRBAG ar e embossed on the airbag covers. NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. The front airbags have a multi stage inflator design. This may allow the airbag to have differ ent rates of inflation that are based on co ...

  • Jeep Liberty (2005) - page 50

    W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured be- cause the airbags are not there to protect you. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating. • If your vehicle is equipped ...

  • Jeep Liberty (2005) - page 51

    airbags work, you need the seat belts to keep you in the right position for the airbags to protect you pr operly . Here ar e some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appr opriate child restraint. Infants in rear -facing chil ...

  • Jeep Liberty (2005) - page 52

    W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instru- ment panel during airbag de ...

  • Jeep Liberty (2005) - page 53

    • Driver and Front Passenger Seat Belt Pr etensioners • Front Passenger Seat Occupant Classification System (OCS) − Occupant Classification Module − Passenger Airbag Disabled (P AD) Indicator Light − Interconnecting W iring − Pressur e Sensor , Bladder Assembly , and Belt T ension Sensor How The Airbag System W orks • The Occupant Res ...

  • Jeep Liberty (2005) - page 54

    in any part of the system, it turns on the AIRBAG warning light either momentarily or continuously . A single chime will sound if the light comes on again after initial start up. W ARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on ...

  • Jeep Liberty (2005) - page 55

    • The Side Impact SRS W indow Bags are designed to activate only in certain side collisions. When the ORC (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes ...

  • Jeep Liberty (2005) - page 56

    If there is a fault pr esent in the system, the AIRBAG warning light will light indicating that you should take the vehicle to an authorized dealer . In the pres- ence of an occupant in the passenger seat, if both the P AD indicator light (located in the front passenger grab handle) and AIRBAG warning light (located in the instrument cluster) ar e ...

  • Jeep Liberty (2005) - page 57

    should always use the P AD indicator light as an indica- tion if the front passenger is pr operly positioned or not. If the P AD indicator light comes on when an adult is in the passenger seat, have the passenger re-position them- selves in the seat until the light goes out. Remember , if the P AD indicator light is illuminated the passenger front ...

  • Jeep Liberty (2005) - page 58

    • The Belt T ension Sensor (BTS) is located at the outboard passenger lap belt anchor . The BTS creates a signal based on outboard lap belt tension. This signal is sent to the OCM to ensure that the r esultant bladder pressur e increase due to applied lap belt tension does not cause a small occupant to be classified as a larger occupant. • The ...

  • Jeep Liberty (2005) - page 59

    • Do not use prior or future model year seat covers not designated for the specific model being repair ed. Al- ways use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover . • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar . • At no time shoul ...

  • Jeep Liberty (2005) - page 60

    However , if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately . As the airbags deflate you may see some smoke-like particles. The particles are a normal by- product of the pr ocess that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin ...

  • Jeep Liberty (2005) - page 61

    Enhanced Accident Response System (E.A.R.S.) If the airbags deploy after an impact and the electrical system remains functional, the interior lights will turn on and the power door locks (if equipped) will unlock 5 seconds after airbag deployment. Also, the fuel system will shut off immediately upon airbag deployment (gasoline models only). The ign ...

  • Jeep Liberty (2005) - page 62

    Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right ...

  • Jeep Liberty (2005) - page 63

    Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint systems. This is the law , and you can be prosecuted for ignoring it. Children 12 years and under should ride pr operly buck- le ...

  • Jeep Liberty (2005) - page 64

    Infants and Small Children There ar e differ ent sizes and types of restraints for children fr om newborn size to the child almost large enough for an adult seat belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is corr ect for your child: • This vehicle is not capable of a ...

  • Jeep Liberty (2005) - page 65

    • Children who weigh mor e than 20 lbs (9 kg) and who are older than one year can ride forwar d-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing dir ection are for children who weigh 20 to 40 lbs (9 to 18 kg), and ar e older than one year old. These child seats are also held in the vehicle b ...

  • Jeep Liberty (2005) - page 66

    Standards. The manufactur er recommends that you try a child restraint in the vehicle seats wher e you will use it before you buy it. • The restraint must be appr opriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instr uctions that come with the restraint. If you ...

  • Jeep Liberty (2005) - page 67

    LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CH ildren) Y our vehicle’s rear seat is equipped with the child restraint anchorage system called LA TCH. The LA TCH system provides for the installation of the child r estraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorage ...

  • Jeep Liberty (2005) - page 68

    Installing the LA TCH-Compatible Child Restraint System W e urge that you car efully follow the directions of the manufacturer when installing your child r estraint. Not all child restraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that were pr ovided with the child restraint system. The re ...

  • Jeep Liberty (2005) - page 69

    In addition, there ar e tether strap anchorages behind each rear seating position located on the back of the seat. Many , but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing todd ...

  • Jeep Liberty (2005) - page 70

    downward into the seat, r emoving slack in the straps according to the child r estraint manufacturer’s instruc- tions. W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when in ...

  • Jeep Liberty (2005) - page 71

    buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate fr om the buckle, turn the buckle aro ...

  • Jeep Liberty (2005) - page 72

    W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Children T oo Large for Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs ar ...

  • Jeep Liberty (2005) - page 73

    ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not r equired for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-thr ottle acceleration, within the limits of local traffic laws, c ...

  • Jeep Liberty (2005) - page 74

    garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine r unning for more than a short period, adjust the ventilation system to force fr esh, outside air into the vehicle. • Guard against carbon monoxide with pr oper mainte- nance. Have the exhaust system inspe ...

  • Jeep Liberty (2005) - page 75

    Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should feel the air directed against the windshield. Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tr ead wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the trea ...

  • Jeep Liberty (2005) - page 76

    ...

  • Jeep Liberty (2005) - page 77

    UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 8 1 ▫ Inside Day/Night Mirror ................. 8 1 ▫ Inside Automatic Dimming Mirror — If Equipped .......................... 8 2 ▫ Outside Mirrors ....................... 8 2 ▫ Power Remote Control Outside Mirr ors — If Equipped ......... ...

  • Jeep Liberty (2005) - page 78

    ▫ Front Seat Adjustment — Recline .......... 1 0 9 ▫ Head Restraints ...................... 1 1 0 ▫ Power Seat Adjuster — If Equipped ........ 1 1 1 ▫ Heated Seats — If Equipped ............. 1 1 2 ▫ 65/35 Split Folding Rear Seat ............. 1 1 3 䡵 T o Open And Close The Hood ............. 1 1 6 䡵 Lights ..................... ...

  • Jeep Liberty (2005) - page 79

    䡵 Electronic Speed Contr ol .................. 1 2 7 ▫ T o Activate .......................... 1 2 7 ▫ T o Set At A Desir ed Speed ............... 1 2 8 ▫ T o Deactivate ........................ 1 2 8 ▫ T o Resume Speed ..................... 1 2 8 ▫ T o V ary The Speed Setting ............... 1 2 8 ▫ T o Accelerate For Passing ....... ...

  • Jeep Liberty (2005) - page 80

    ▫ Cargo T ie-Down Hooks ................. 1 5 2 ▫ Cargo Or ganizer — If Equipped ........... 1 5 4 䡵 Rear W indow Features ................... 1 5 6 ▫ Rear W indow W iper/W asher ............. 1 5 6 ▫ Rear W indow Defroster ................. 1 5 8 䡵 Roof Luggage Rack ..................... 1 5 9 80 UNDERST ANDING THE FEA TURES OF YOUR ...

  • Jeep Liberty (2005) - page 81

    MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the r ear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror . The mirror should be adjusted while set in the day position (toward windshield). Annoying headlight glare fr om vehicles behind you can be reduced by mo ...

  • Jeep Liberty (2005) - page 82

    Inside Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during cl ...

  • Jeep Liberty (2005) - page 83

    W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other objects. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror . Power R ...

  • Jeep Liberty (2005) - page 84

    Heated Remote Control Mirrors — If Equipped These mirrors ar e heated to melt frost or ice. This feature is activated whenever you turn on the r ear window defrost. Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor . T o use the mirror , rotate the sun visor down and swing the mirror cover upwar d. The l ...

  • Jeep Liberty (2005) - page 85

    HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g., ⬙ Call ѧ Mike ѧ W ork ⬙ or ⬙ Dial ѧ 248-555-1212 ⬙ ). Y our cellular phone’s audio is transm ...

  • Jeep Liberty (2005) - page 86

    with the system at a time. The system is available in English, Spanish, or French languages (as equipped). The rearview mirr or contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the ⬙ ...

  • Jeep Liberty (2005) - page 87

    The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can either be adjusted from the radio volume control knob, or fr om the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts fr om the UConnect™ system such as ⬙ CELL ⬙ or ...

  • Jeep Liberty (2005) - page 88

    Help Command If you need assistance at any prompt or if you want to know what your options are at any pr ompt, say ⬙ Help ⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help. T o activate the UConnect™ system from idle, simply press the ’Phone’ button and follow audible pr ompt ...

  • Jeep Liberty (2005) - page 89

    • Y ou will be asked to say a four-digit pin number which you will later need to enter into your cellular . Y ou can enter any four-digit pin number . Y ou will not need to remember this pin number after the initial pairing process. • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. ...

  • Jeep Liberty (2005) - page 90

    • For example, you can say ⬙ 234-567-8901. ⬙ The phone number that you enter must be of valid length and combination. The UConnect™ limits the user from dialing invalid combination of numbers. For example, 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. • The UConnect™ ...

  • Jeep Liberty (2005) - page 91

    • When prompted, say the name of the new entry . Use of long names helps the voice recognition and is r ecom- mended. For example, say ⬙ Robert Smith ⬙ or ⬙ Robert ⬙ instead of ⬙ Bob. ⬙ • When prompted, enter the number designation (e.g.: ⬙ Home, ⬙⬙ W ork, ⬙⬙ Mobile, ⬙ or ⬙ Pager ⬙ ). This will allow you to store mul ...

  • Jeep Liberty (2005) - page 92

    After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙ Phonebook Edit ⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may ha ...

  • Jeep Liberty (2005) - page 93

    • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook List Names. ? ...

  • Jeep Liberty (2005) - page 94

    Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in pr ogress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the curr ent call on hold and answer the incoming call. NOTE: The UConne ...

  • Jeep Liberty (2005) - page 95

    Conference Call When two calls are in pr ogress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-W ay Calling T o initiate three-way calling, pr ess the ’V oice Recogni- tion’ button while a call is in progr ess and mak ...

  • Jeep Liberty (2005) - page 96

    • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred fr om the UConnect™ system to the mobile phone. • An active call is automatically transferred to the mobile phone after ignition key is switched to off. UConnect™ System Features Lang ...

  • Jeep Liberty (2005) - page 97

    • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Emergency ⬙ and the UConnect™ system will instr uct the paired cellular phone to call the emer gency num- ber . This feature is only supported in the USA. NOTE: The emergency number dialed is based on the Country where the vehicle is pur chased (91 1 for USA/ Canada and 060 for ...

  • Jeep Liberty (2005) - page 98

    Paging T o learn how to page, refer to section ⬙ W orking with Automated Systems. ⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. V oice Mail Calling T o learn how to access your voice mail, refer to section ⬙ W orking with Automated Systems. ⬙ W o ...

  • Jeep Liberty (2005) - page 99

    T urning Confirmation Prompts On/Off T urning confirmation prompts of f will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number befor e you dial it). • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Confirmations. ⬙ The UConn ...

  • Jeep Liberty (2005) - page 100

    Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party , but the other party will not be able to hear you. In order to mute the UConnect™ system: • Press the ’V oice Recognition’ button. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Mute. ...

  • Jeep Liberty (2005) - page 101

    Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Y our cellular phone can be paired with many dif ferent electronic devices, but can only be actively ⬙ connected ⬙ with one electronic device at a time. If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone ...

  • Jeep Liberty (2005) - page 102

    • When prompted say the priority number of the cellu- lar phone you wish to select. Y ou can also press the ⬘ V oice Recognition’ button anytime while the list is being played and say the priority number . • The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return ...

  • Jeep Liberty (2005) - page 103

    • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English and Spanish accents, the system may not always work for some. • ...

  • Jeep Liberty (2005) - page 104

    • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as, audio clarity , echo. and loud- ness to a large degr ee, rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluet ...

  • Jeep Liberty (2005) - page 105

    UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 105 3 ...

  • Jeep Liberty (2005) - page 106

    106 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...

  • Jeep Liberty (2005) - page 107

    UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 107 3 ...

  • Jeep Liberty (2005) - page 108

    North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up ...

  • Jeep Liberty (2005) - page 109

    Using body pressur e, move forward and r earward on the seat to be sure the seat adjusters have latched. W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehic ...

  • Jeep Liberty (2005) - page 110

    Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The head restraints have a locking button that must be pushed inward to lower the head restraint. The r estraints may be raised without pushing ...

  • Jeep Liberty (2005) - page 111

    Power Seat Adjuster — If Equipped W ARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. 6–W ay Power Seat with Manual Recliner The seat switch is ...

  • Jeep Liberty (2005) - page 112

    This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. Heated Seats — If Equipped The heated seat switch is located on the outboard side of the front seats. Pr essing this switch to its desired setting (HI or LO) will activate the respective heating element for the he ...

  • Jeep Liberty (2005) - page 113

    Once the heated seat switch is activated, depressing it a second time will de-activate it. 65/35 Split Folding Rear Seat T o provide additional storage ar ea, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating r oom. NOTE: Prior to folding the rear seat, it may be necessary to reposition the fr ...

  • Jeep Liberty (2005) - page 114

    T o fold the 65/35 rear seat, perform the following steps: 1. Locate the seatback release handle on the outboard top side of each rear seatback; lift up on the handle, and rotate the lever forwar d until the seatback releases. Fold the seatback completely forward. NOTE: When lifting up on the release handle, the seatback will release easier if you ...

  • Jeep Liberty (2005) - page 115

    T o restore the 65/35 rear seat to the upright position perform the following steps: Raise the seatback and lock it into place. If interference from the car go area pr events the seatback from fully locking, you will have difficulty r eturning the seat to its proper position. The seat r elease handle will be flush with the seatback when the seat is ...

  • Jeep Liberty (2005) - page 116

    TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever inside your vehicle located under the left side of the instrument panel. Then, reach under the hood and slide the safety latch to the right and lift the hood. T o prevent possible damage, do not slam the hood to close it. Lower the hood unt ...

  • Jeep Liberty (2005) - page 117

    secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. LIGHTS Interior Lights The overhead lights will come on when a door ...

  • Jeep Liberty (2005) - page 118

    Daytime Brightness Feature Certain components (odometer , radio, etc.) can be illumi- nated at full brightness during the daytime. This can be helpful when driving with your headlights on during the daytime such as in a parade or a funeral procession. T o activate this feature, r otate the multi-function control lever one detent lower than the dome ...

  • Jeep Liberty (2005) - page 119

    Parking Lights, Instrument Panel Lights, and Headlights T urn the end cap of the multi-function control lever to the first detent for parking lights and instrument panel lights. T urn to the second detent for headlight operation. T o change the brightness of the instrument panel lights, rotate the center portion of the multi-function contr ol lever ...

  • Jeep Liberty (2005) - page 120

    NOTE: A tone will chime if the turn signals are left on for more than 2 miles (3.2 km). Lights-On Reminder A chime will sound if the driver’s door is left open, and the headlights or parking lights are left on. Battery Saver Feature — Exterior Lights If the park lights, headlights, fog lights, or high beams are left on when the ignition switch ...

  • Jeep Liberty (2005) - page 121

    Light Bar — If Equipped 1. Remove lamp covers by pressing the thumb tab up- wards, and pulling the cover of f. CAUTION! The auxiliary lights mounted on the off road light bar should be illuminated during ⴖ OFF-ROAD USE ONL Y . ⴖ Having them illuminated on public streets, highways, roads, etc. may be illegal in your state. Y our state may also ...

  • Jeep Liberty (2005) - page 122

    2. W ith the ignition in the ON position, press the button to turn on the light bar (located on the instrument panel to the left of the steering column). Press the button again to turn off the light bar . An indicator light in the instrument cluster will illumi- nate when the light bar has been activated. T o reinstall lamp covers, insert the tab u ...

  • Jeep Liberty (2005) - page 123

    WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch on the control lever . This control lever is located on the right side of the steering column. For front wiper operation, turn the control lever end cap upwar d to select the desired wiper speed. W indshield Wiper/W asher Switch UNDERST ANDING THE FEA TURES OF YOUR VEHIC ...

  • Jeep Liberty (2005) - page 124

    Windshield W ashers T o use the washer , pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then r esume the intermit- tent interval previously selected. NOTE: If vehicle is equipped with the optional Elec- tronic V e ...

  • Jeep Liberty (2005) - page 125

    Mist Feature Push down on the wiper lever to activate a single wipe to clear off r oad mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. CAUTION! In cold weather , always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wip ...

  • Jeep Liberty (2005) - page 126

    TIL T STEERING COLUMN T o tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towar ds you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. T ilt Steering Column 126 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...

  • Jeep Liberty (2005) - page 127

    W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator opera- ...

  • Jeep Liberty (2005) - page 128

    T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate the Speed Control without erasing the memory . Pressing ...

  • Jeep Liberty (2005) - page 129

    T o Accelerate for Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. NOTE: When driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. (If the vehicle speed drops ...

  • Jeep Liberty (2005) - page 130

    Pressing the MENU button will change the displayed programming featur es. Pressing the STEP button will select the available choices. Pressing the C/T (Compass/ T emperature) button will r eturn the display to the normal compass/temperature display . NOTE: T emperature accuracy can be ef fected from heat soak. For best accuracy , the vehicle should ...

  • Jeep Liberty (2005) - page 131

    The reading lights ar e activated by pressing on the recessed ar ea of the corresponding lens. NOTE: The dome/reading lights will r emain on until the switch is pressed a second time, so be sur e they have been turned off befor e leaving the vehicle. Electronic V ehicle Information Center The electronic vehicle information center (EVIC), when the a ...

  • Jeep Liberty (2005) - page 132

    Customer Programmable Features Press the MENU button until one of the display choices following appears: Language? When in this display you may select one of five lan- guages for all display nomenclature, including the trip computer functions. Press the STEP button while in this display to select English, Francais, Deutsch, Italiana, or Espanol. As ...

  • Jeep Liberty (2005) - page 133

    ALL DOORS. This can also be programmed using the key fob, refer to “Remote Keyless Entry” earlier in this section. T rain Remote? Pressing the STEP button when in this display will select “Y es” or “No.” NOTE: Any time you perform this procedur e, it is necessary to retrain all curr ently trained key fobs. T o T rain Additional Key Fobs ...

  • Jeep Liberty (2005) - page 134

    Flash Lights W ith Locks? When this feature is selected, the fr ont and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter . This feature may be selected with or without the sound horn on lock feature selected. Pr essing the STEP button when in this display will select “Y es” or “No.? ...

  • Jeep Liberty (2005) - page 135

    Mini-T rip Computer This feature, located in the over head console, displays information on outside temperature, compass dir ection, and trip information. Reset Button Use this button to reset the A verage Economy , T rip Miles, and T ime Elapsed displays to zero. This will occur only if a resettable function is curr ently being displayed (A ver- a ...

  • Jeep Liberty (2005) - page 136

    W ARNING! Even if the display still reads a few degrees above 32°F (0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Step Button Press the STEP button to cycle through all of the displays. The displays are: A ver ...

  • Jeep Liberty (2005) - page 137

    T ire PSI Shows the pressur e and location of each tire, except for the spare tir e. The tire location will blink when under pressur e. Blank Screen Shows a blank screen. Pr essing the C/T button returns to the Compass and T emperature display . Pressing the STEP button returns you to the A verage Miles per Gallon display . Automatic Compass Calibr ...

  • Jeep Liberty (2005) - page 138

    Compass V ariance is the difference between magnetic north and geographic north. In some areas of the country , the differ ence between magnetic and geographic north is great enough to cause the compass to give false r eadings. If this occurs, the compass variance must be set according to the Compass V ariance Map. T o set the variance: T urn the i ...

  • Jeep Liberty (2005) - page 139

    General Information This transmitter complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference that may be received, including interfer ence that may cause undes- ired operation CAUTION! Chan ...

  • Jeep Liberty (2005) - page 140

    W ARNING! Before programming HomeLink to a garage door opener or gate operator , make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener , it is advised to park outside of the garage. Do not use HomeLink with any garage door opener that lacks safety stop and rever ...

  • Jeep Liberty (2005) - page 141

    Programming HomeLink NOTE: It is recommended that a new battery be placed in the hand-held transmitter of the device being pro- grammed to HomeLink for quicker training and accurate transmission of the radio frequency signal. W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s engine while programming ...

  • Jeep Liberty (2005) - page 142

    2. Simultaneously press and hold both the desired HomeLink button and the hand-held transmitter button. After a short time, the message TRAINING will show on HomeLink display . Do not release the buttons until the next step has been completed. 3. When the message TRAINED appears on the HomeLink display , release both the HomeLink and hand- held tra ...

  • Jeep Liberty (2005) - page 143

    If the message TRANSMIT appears on the HomeLink display but your device does not activate, the device may be equipped with a ⬙ rolling code ⬙ system. Continue with steps five through seven below to complete the pr ogram- ming of a rolling code equipped device (most commonly a garage door opener). 5. At the garage door opener receiver (motor-hea ...

  • Jeep Liberty (2005) - page 144

    If, after programming the HomeLink W ireless Control System, the hand-held transmitter and/or other HomeLink units in other vehicles fail to activate the rolling code equipped device, you may need to clear (or ⴖ erase ⴖ ) the device’s receiver memory . Refer to your garage door opener’s Owner’s Manual for the proce- dure or contact HomeLi ...

  • Jeep Liberty (2005) - page 145

    Press and hold the HomeLink button while you press and release - every two seconds ( ⴖ cycle ⴖ ) your hand-held transmitter button until the radio signal has success- fully been accepted by HomeLink. (The message TRAINED will appear on the HomeLink display .) Proceed with the r emaining steps under ⬙ Programming HomeLink ⬙ to complete. Usin ...

  • Jeep Liberty (2005) - page 146

    Press and hold the switch r earward to fully open the sunroof. The sunr oof can be stopped at any position between closed and full open. Momentarily pressing the switch rearwar d will activate the Express Open Featur e, causing the sunroof to open automatically . Press and hold the “V” button in the center of the sunr oof switch to open the ven ...

  • Jeep Liberty (2005) - page 147

    the sunroof and the sunr oof will remain in the partial vent position until the switch is pushed forward again. Express Open Feature During the Express Open operation, any movement of the switch will stop the sunroof and it will r emain in a partial open position. Again, momentarily pressing the switch rearwar d will activate the Express Open Featu ...

  • Jeep Liberty (2005) - page 148

    POWER OUTLET T o the right of the convenience tray (lower center of instrument panel) is an outlet for electrically power ed accessories. Pull lightly on the top of the plastic cover to open the outlet. There is a r ear power outlet located in the right rear car go area above the storage car go net/CD changer (if equipped). Front Power Outlet Rear ...

  • Jeep Liberty (2005) - page 149

    The rear power outlet is a dir ect feed from the battery so it receives power whether the ignition is in the ON or OFF position. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use. CAUTION! Electrical Outlet Use W ith Engine Off • Many accessories that can be plugged in draw power from the ve ...

  • Jeep Liberty (2005) - page 150

    CUP HOLDERS In the center console there ar e two cup holders for the front seat passengers. NOTE: The front cup holder insert is r emovable from the console, for cleaning. Smoker’s Package — If Equipped W ith the optional Smoker’s package, a removable ash tray is inserted into the front cup holder location. The rear passengers have access to ...

  • Jeep Liberty (2005) - page 151

    CARGO AREA FEA TURES Cargo Light The cargo ar ea light is activated by opening the swing gate, opening any door , or by rotating the dimmer contr ol on the multi-function control lever to the extr eme top position. If all doors are closed and only the swing gate is open, pushing on the cargo light lens surface will turn of f all interior lights. Pu ...

  • Jeep Liberty (2005) - page 152

    W ARNING! In an accident a cargo cover loose in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle. Cargo Tie-Down Hooks ...

  • Jeep Liberty (2005) - page 153

    W ARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • The weight and position of cargo and passengers can change the vehicle center ...

  • Jeep Liberty (2005) - page 154

    Cargo Organizer — If Equipped This vehicle may be equipped with a cargo or ganizer that mounts on the floor behind the rear seat. Items may be placed on the flat surface or stored in the thr ee storage compartments. W ARNING! • T o avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or ...

  • Jeep Liberty (2005) - page 155

    2. Place the rear corners of the cargo or ganizer into the supports located on the rear trim panel. Pr ess down on the back of the cargo or ganizer to lock it into place. W ARNING! Do not load objects over 30 lbs (13.5 kg) in the upper position. Failure to follow this warning could cause the cargo organizer to collapse resulting in personal injury ...

  • Jeep Liberty (2005) - page 156

    T o Open Storage Compartments 1. Pull up on the center opening of the cargo organizer . 2. Lift up on the storage compartment dividers and lock into place. Cargo Organizer Removal Loosen screw , then lift lever from each mount located on the floor of the rear car go area, and r emove the cargo organizer fr om the vehicle. REAR WINDOW FEA TURES Rear ...

  • Jeep Liberty (2005) - page 157

    If the rear wiper is operating when the ignition is turned OFF , the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at. If the swing gate flip-up window is open or the swing gate is open, connection to the rear window wiper is interrup ...

  • Jeep Liberty (2005) - page 158

    Rear Window Defroster On the top of the climate control panel is a push button for rear window defr osting. An amber indicator in the push button will light when the defroster is turned on. Push again to turn off the defr oster prior to an automatic time-out. The defroster will automatically turn of f after about ten minutes. For about five more mi ...

  • Jeep Liberty (2005) - page 159

    ROOF LUGGAGE RACK External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the rated vehicle capacity as shown on the label attached to the drivers door shut face. CAUTION! • T o avoid damage to the roof rac ...

  • Jeep Liberty (2005) - page 160

    W ARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack. 160 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...

  • Jeep Liberty (2005) - page 161

    UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel And Interior Contr ols ....... 1 6 5 䡵 Instrument Cluster ...................... 1 6 6 ▫ 2.4L/3.7L Engines ..................... 1 6 6 ▫ 2.8L Diesel Engines .................... 1 6 7 䡵 Instrument Cluster Description ............. 1 6 8 䡵 Electronic Digital Clock ........ ...

  • Jeep Liberty (2005) - page 162

    ▫ T uning ............................. 1 7 9 ▫ Radio Data System (RDS) ............... 1 7 9 ▫ PTY (Pr ogram T ype) Button .............. 1 7 9 ▫ Balance ............................ 1 8 1 ▫ Fade .............................. 1 8 1 ▫ T one Control ........................ 1 8 1 ▫ AM/FM Selection ..................... 1 8 1 ▫ Scan ...

  • Jeep Liberty (2005) - page 163

    ▫ Mode .............................. 1 8 6 ▫ T ape CD Button ...................... 1 8 6 ▫ T ime Button ......................... 1 8 7 ▫ Scan Button ......................... 1 8 7 ▫ CD Changer Control Capability — If Equipped ......................... 1 8 7 䡵 Sales Code RBK—AM/ FM Stereo Radio W ith CD Player And CD Changer Cont ...

  • Jeep Liberty (2005) - page 164

    ▫ Using The PTY (Pr ogram T ype) Button (If Equipped) ........................ 2 0 6 ▫ PTY Button ⬙ Scan ⬙ ..................... 2 0 6 ▫ PTY Button ⬙ Seek ⬙ ..................... 2 0 7 ▫ Satellite Antenna ...................... 2 0 7 ▫ Reception Quality ..................... 2 0 7 䡵 Remote Sound System Controls — If Equipped . ...

  • Jeep Liberty (2005) - page 165

    INSTRUMENT P ANEL AND INTERIOR CONTROLS UNDERST ANDING YOUR INSTRUMENT P ANEL 165 4 ...

  • Jeep Liberty (2005) - page 166

    INSTRUMENT CLUSTER 2.4L/3.7L ENGINES 166 UNDERST ANDING YOUR INSTRUMENT P ANEL ...

  • Jeep Liberty (2005) - page 167

    2.8L DIESEL ENGINES UNDERST ANDING YOUR INSTRUMENT P ANEL 167 4 ...

  • Jeep Liberty (2005) - page 168

    INSTRUMENT CLUSTER DESCRIPTION 1. T achometer Indicates the permissible engine revolutions-per -minute for each gear range. Before r eaching the red ar ea, ease up on the accelerator to prevent engine damage. 2. T urn Signal Indicator Light The arrows will flash in unison with the exterior turn signals, when using the multi-function control lever . ...

  • Jeep Liberty (2005) - page 169

    the vehicle’s handling and stopping ability . Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pr essure as specified on the vehicle placard. (See page 268 for mor e information.) 6. 4LO Mode Indicator Light — If Equipped This light alerts the driver that the vehicle is in the 4 LO four– ...

  • Jeep Liberty (2005) - page 170

    converter damage. The vehicle should be serviced as soon as possible if this occurs. (See page 309 for more information.) 9. Anti-Lock W arning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition switch is turned to the ON position and may sta ...

  • Jeep Liberty (2005) - page 171

    1 1. T emperature Gage Indicates engine coolant temperature. Any read- ing within the normal range indicates that the cooling system is operating satisfactorily . The gage pointer will likely indicate a higher temperature (above center scale) when driving in hot weather , up mountain grades, in heavy stop and go traffic, or when towing a trailer . ...

  • Jeep Liberty (2005) - page 172

    EVIC display (not in the instrument cluster). For addi- tional information, refer to “Over head Console — If Equipped” in Section 3. U.S. federal regulations r equire that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Ther e- fore, if the odometer r eading is chan ...

  • Jeep Liberty (2005) - page 173

    17. Part T ime Indicator Light — If Equipped This light alerts the driver that the vehicle is in the P AR T TIME four–wheel drive high range mode, and the front and r ear driveshafts are mechanically locked together forcing the fr ont and rear wheels to rotate at the same speed. (See page 236 for more information.) 18. Brake W arning Light This ...

  • Jeep Liberty (2005) - page 174

    Also, the light will come on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. If the parking brake is off and the light r emains on, have the brake system inspected as soon as possible. 19. Full T ime Indica ...

  • Jeep Liberty (2005) - page 175

    24. O/D (Overdrive) Off Indicator Light This light will illuminate when the O/D OFF button has been selected. The O/D OFF button is located on the gear shift lever . 25. Seat Belt Indicator Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat bel ...

  • Jeep Liberty (2005) - page 176

    off. If the light r emains lit with the engine running your vehicle will usually be drivable, however , see your dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is r e- quired and you may experience r educed performance, an elevated/rough idle or engine stall and your vehicle may requir ...

  • Jeep Liberty (2005) - page 177

    RADIO GENERAL INFORMA TION Radio Broadcast Signals Y our new radio will provide excellent r eception under most operating conditions. Like any system, however , car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. T o help you understand and sa ...

  • Jeep Liberty (2005) - page 178

    remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle fr ont door will cancel this feature. SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE T APE PLA YER, CD PLA YER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. Operating Instructions ? ...

  • Jeep Liberty (2005) - page 179

    T uning Press the TUNE contr ol up or down to increase or decrease the fr equency . If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Radio Data System (RDS) The Radio Data System allows radio broadcasting sta- tions ...

  • Jeep Liberty (2005) - page 180

    Program T ype Radio Display Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Program T ype Radio D ...

  • Jeep Liberty (2005) - page 181

    Pressing PTY , then SCAN will scan the FM Band and stop at all RDS stations. Each RDS station will be played for a 5 second scan once around the FM Band and stop at the last station. The PTY icon will then turn of f. Balance The Balance control adjusts the left-to-right speaker bal- ance. Push in the button and it will pop out. Adjust the balance a ...

  • Jeep Liberty (2005) - page 182

    T o Set The Radio Push-button Memory When you are r eceiving a station that you wish to commit to push-button memory , press the SET button. SET 1 will show in the display window . Select the push-button you wish to lock onto this station and press and release that button. If a station is not selected within 5 seconds after pressing the SET button, ...

  • Jeep Liberty (2005) - page 183

    Press the SEEK button up or down to move the track number to skip forward or backwar d 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed aga ...

  • Jeep Liberty (2005) - page 184

    Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch r oller will automatically retract to pr otect the tape from any damage. When power is r estored to the tape player , the pinch roller will automatically r eengage and the tape will resume play . Noise Reduction The Dolby Noise Reduction System* is on whenev ...

  • Jeep Liberty (2005) - page 185

    If the volume control is ON, the unit will switch fr om radio to CD mode and begin to play . The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: • Y ou may eject a disc with the radio OFF . The ignition switch must be in the ON or ACC position to insert a disc with the rad ...

  • Jeep Liberty (2005) - page 186

    FF/TUNE/RW Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play . This feature plays the tracks on the se- lected disc in random order to pr ovide an interesti ...

  • Jeep Liberty (2005) - page 187

    Time Button Press this button to change the display fr om elapsed CD playing time to time of day . Scan Button Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available thr ...

  • Jeep Liberty (2005) - page 188

    Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an inter esting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will ...

  • Jeep Liberty (2005) - page 189

    SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLA YER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. NOTE: Power to operate the radio is suppli ...

  • Jeep Liberty (2005) - page 190

    T une Press the TUNE contr ol up or down to increase or decrease the fr equency . If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. T o Set The Radio Push-Button Memory When you are r eceiving a station that you wish ...

  • Jeep Liberty (2005) - page 191

    Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and F ADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and r ear speakers. Press the AUDIO button again or wai ...

  • Jeep Liberty (2005) - page 192

    Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may either insert or eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day . If the power is ON, the ...

  • Jeep Liberty (2005) - page 193

    FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play . This feature plays the tracks on the selected disc in random order to pr ...

  • Jeep Liberty (2005) - page 194

    Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display . Fast Forward And Rewind Buttons Press and ...

  • Jeep Liberty (2005) - page 195

    CD HOT will pause the operation. Play can be resumed when the operating temperature is corr ected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following r easons: • Excessive vibration • Disc inserted upside down • Damaged disc • W ater condensation on optics SALE ...

  • Jeep Liberty (2005) - page 196

    NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button r epeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received. T o select Sirius Satellite Radio? ...

  • Jeep Liberty (2005) - page 197

    and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in the d ...

  • Jeep Liberty (2005) - page 198

    General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesir ed opera- tion. NOTE: Changes or modifications ...

  • Jeep Liberty (2005) - page 199

    show the disc number , the track number , and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number wher e the CD is being loaded. After the radio displays “load” insert the CD into the player . Radio display will show “loading” ...

  • Jeep Liberty (2005) - page 200

    FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play . This feature plays the tracks on the disc in random order to pr ovide an interesting change of ...

  • Jeep Liberty (2005) - page 201

    Program T ype Radio Display Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY i ...

  • Jeep Liberty (2005) - page 202

    T ime Press the TIME button to change the display fr om elapsed CD playing time to time of day . Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will not damage the di ...

  • Jeep Liberty (2005) - page 203

    SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NA VIGA TION SYSTEM The navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “Navi- gation User’s Manual” for detailed operating instruc- tions. NOTE: If your vehicle is not equipped with the C ...

  • Jeep Liberty (2005) - page 204

    System Activation T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Y our V ehi ...

  • Jeep Liberty (2005) - page 205

    ESN/SID Access W ith RBP , RBU, RAZ, RB1 and RBQ Radios W ith the ignition switch in the ACCESSOR Y position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF , or 5 min ...

  • Jeep Liberty (2005) - page 206

    Selecting a Channel Press and r elease the SEEK or TUNE buttons to search for the next channel. Press the top of the button to sear ch up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Press and r elease the SCAN button (if equipped) to automatically change chan ...

  • Jeep Liberty (2005) - page 207

    NOTE: Pressing the ⬙ SEEK ⬙ or ⬙ SCAN ⬙ button while performing a music type scan will change the channel by one and stop the search. Pr essing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button ⴖ SEEK ⴖ When the desired pr ogram is obtained, press the ⬙ SEEK ⬙ button wi ...

  • Jeep Liberty (2005) - page 208

    REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the r ear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a r ocker type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the r ocker s ...

  • Jeep Liberty (2005) - page 209

    Radio Operation Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch will “Seek” down for the next listenable station. The button located in the center of the left hand control will tune to the next preset station that you have pr o- grammed in the radio preset push-button. T ap ...

  • Jeep Liberty (2005) - page 210

    If you press the switch up or down twice it plays the second track, three times, it will play the thir d, etc. The button in the center of the left hand switch will cause the CD changer to play the next available disc in the 6–disc magazine. CASSETTE T APE AND PLA YER MAINTENANCE T o keep the cassette tapes and player in good condition, take the ...

  • Jeep Liberty (2005) - page 211

    As preventive maintenance, clean the head about every 30 hours of use. If you wait until the head becomes very dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette. CD/DVD DISC MAINTENANCE T o keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by it ...

  • Jeep Liberty (2005) - page 212

    CLIMA TE CONTROLS The controls for the heating, air conditioning, and venti- lation system in this vehicle consist of a series of rotary knobs, and a push-button. These comfort controls can be set to obtain desired interior conditions. Blower Control The rotary knob on the left contr ols the blower and can be set in one of four positions from Low t ...

  • Jeep Liberty (2005) - page 213

    OFF This position turns off the blower motor and outside air will not pass through any outlets. Recirculate (Max A/C) Air flows through the outlets located in the instrument panel. Allows for circulation of interior air only which will cool the cabin faster . This setting can be used in very hot weather to maximize the effect of the air conditioner ...

  • Jeep Liberty (2005) - page 214

    Mix Air flows through the floor outlets, the outlets at the base of the windshield, and the side window demisters outlets. Defrost Air flows through the outlets at the base of the windshield and through the side window demister outlets. Operating Tips Fast Cool Down For a fast cool down, turn the blower fan rotary knob to the extreme clockwise posi ...

  • Jeep Liberty (2005) - page 215

    Summer Operation Air conditioned equipped vehicle’s cooling systems must be protected with a high quality engine coolant during summer to provide pr oper corrosion pr otection and to raise the boiling point of the coolant for protection against overheating. A 50% concentration is recom- mended. W inter Operation When operating the system during t ...

  • Jeep Liberty (2005) - page 216

    ...

  • Jeep Liberty (2005) - page 217

    ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 2 0 ▫ Manual T ransmission .................. 2 2 0 ▫ Automatic T ransmission ................ 2 2 0 ▫ Normal Starting — Gasoline Engines ....... 2 2 1 ▫ Normal Starting — Diesel Engines ......... 2 2 3 ▫ Diesel Fuel-W ater Separator .............. 2 2 ...

  • Jeep Liberty (2005) - page 218

    ▫ Shift Positions ........................ 2 4 2 ▫ Shifting Procedur e .................... 2 4 3 䡵 T rac-Lok™ Rear Axle — If Equipped ......... 2 4 5 䡵 Parking Brake ......................... 2 4 5 䡵 Anti-Lock Brake System — If Equipped ....... 2 4 7 䡵 On-Road Driving T ips ................... 2 4 9 䡵 Off-Road Driving T ips ... ...

  • Jeep Liberty (2005) - page 219

    ▫ T ire Pressur e Monitoring — Base System ..... 2 6 8 ▫ T ire Pressur e Monitoring — Premium System . 270 ▫ General Information ................... 2 7 3 䡵 T ire Chains ........................... 2 7 4 䡵 T ire Rotation Recommendations ............ 2 7 5 䡵 Fuel Requirements (Gasoline Engines) ........ 2 7 6 ▫ Reformulated Gasolin ...

  • Jeep Liberty (2005) - page 220

    ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. W ARNING! Do not leave children or animals inside parked vehicles in hot weather . Interior heat build up may cause serious injury or death. Manual T ransmission Apply the parking brake, place the gearshift contro ...

  • Jeep Liberty (2005) - page 221

    Normal Starting — Gasoline Engines Normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. T urn the key to the ST AR T position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the normal sta ...

  • Jeep Liberty (2005) - page 222

    W ARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury . If Engine Fails to Start If the engine fails to start after you have followed the “Normal Starting” procedur e, it may be flooded. Push the accelera ...

  • Jeep Liberty (2005) - page 223

    If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor , the “Normal Starting” procedur e should be repeated. After Starting The idle speed is automatically controlled and will de- crease as the engine warms up. Normal Starting — Diesel Engines 1. T urn the ignition key to ...

  • Jeep Liberty (2005) - page 224

    T urbocharger “Cool Down” NOTE: Letting the engine idle after extended operation allows the turbine housing to cool to normal operating temperature. The following chart should be used as a guide in deter- mining the amount of engine idle time requir ed to sufficiently cool down the turbochar ger before shut down, depending upon the type of driv ...

  • Jeep Liberty (2005) - page 225

    Diesel Fuel-W ater Separator A diesel fuel-water separator separates the water nor- mally found in diesel fuel. A manual hand prime pump is located on the filter head for re-priming the fuel system. The fuel-water separator is located on the driver side cowl in the engine compartment. Refer to “2.8L T urbo Diesel Engine Compartment” in Section ...

  • Jeep Liberty (2005) - page 226

    3. Depress the fuel-water separator knob 20 consecutive times. 4. T urn the ignition to ST AR T and crank the engine a maximum of 10 seconds. If the engine does not start, repeat Step 3. NOTE: The engine will typically start within 10 sec- onds; the engine will idle then stall, purging air fr om the fuel lines and filter . 5. Depress the fuel-water ...

  • Jeep Liberty (2005) - page 227

    W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10-1 15 volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0°F (-18°C) ar e expected to last for several days. TRANSMISSION SHIFTING 6-Speed Manual T ransmission Follow the shift pattern on the gearshift knob. NOTE: The backup lights w ...

  • Jeep Liberty (2005) - page 228

    W ARNING! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. CAUTION! T o drive as safely as possible and to prolong the life of your manual transmission, follow these ...

  • Jeep Liberty (2005) - page 229

    • When “rocking” a stuck vehicle by shifting between a forward gear and r everse, do not spin wheels faster than 15 mph (24 km/h), or drivetrain damage may result. Recommended Manual T ransmission Shifting Speeds The manufacturer r ecommends that you use the shift speeds listed in the chart below . Manual T ransmission Shift Speeds in MPH (KM ...

  • Jeep Liberty (2005) - page 230

    Automatic T ransmission Shifting from D (Drive) to P (Park) or R (Reverse) (or from P or R to D) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. W ARNING! It is dangerous to shift the selector lever out of “P” or “N? ...

  • Jeep Liberty (2005) - page 231

    Gear Ranges P (Park) Supplements the parking brake by locking the transmis- sion. The engine can be started in this range. Never use P (Park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always place the gear selector in the P (Park) position first, and then apply the parking brake. W ARNING! Unint ...

  • Jeep Liberty (2005) - page 232

    The following indicators should be used to ensure that you have engaged the transmission shift lever into the P (Park) position: • When shifting into P (Park), depr ess the button on the shift lever and firmly move the lever all the way forward until it stops. • Look at the shift indicator window on the console to ensure it is in the P (Park) p ...

  • Jeep Liberty (2005) - page 233

    Overdrive (O/D) For most city and highway driving. The transmission contains an electronically contr olled Overdrive, and will automatically shift from D (Drive) to O/D (Over drive) if the following conditions are pr esent: • The transmission selector is in D (Drive). • The O/D OFF button has not been activated. • V ehicle speed is above appr ...

  • Jeep Liberty (2005) - page 234

    NOTE: If the vehicle is started in cold outside tempera- tures, shifts into Over drive may be delayed. Normal Overdrive and shifting operation will r esume when the temperature of the transmission r eaches the appropriate temperature. Refer to the “Note” under “T orque Con- verter Clutch” later in this section. If the transmission temperatu ...

  • Jeep Liberty (2005) - page 235

    Over T emperature Mode The transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may r esult in a slightly differ ent feeling or response during normal operation in D (Drive) position. If the transmission beco ...

  • Jeep Liberty (2005) - page 236

    normal condition and will not cause damage to the transmission. The torque converter will r efill within 5 seconds of shifting from P (Park) into any other gear position. Rocking the V ehicle If the vehicle becomes stuck in snow , sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between “First” and R ...

  • Jeep Liberty (2005) - page 237

    When additional traction is requir ed the transfer case 4H and 4L positions can be used to lock the front and r ear driveshafts together and force the fr ont and rear wheels to rotate at the same speed. This is accomplished by simply moving the shift lever to these positions. The 4H and 4L positions are intended for loose, slippery road surfaces on ...

  • Jeep Liberty (2005) - page 238

    Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel. Any differ ence will adversely affect shifting and can cause damage to the transfer case. W ARNING! • Because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster ...

  • Jeep Liberty (2005) - page 239

    4L 4-Wheel-Drive Low Range - Low speed 4 wheel drive. Locks the front and r ear driveshafts together . Forces the front and r ear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only . Do not exceed 25 mph (40 km/h). (Allows engine starting without depressing the clutch pedal on ve ...

  • Jeep Liberty (2005) - page 240

    NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be requir ed for clutch teeth alignment and shift completion to occur . The pre- ferred method is with the vehicle r olling 2 to 3 mph (3 to 5 km/h). A void ...

  • Jeep Liberty (2005) - page 241

    The P AR T TIME indicator light, located on the instru- ment cluster , illuminates when the transfer case is shifted to the 4 P AR T TIME position. The FULL TIME indicator light, located on the instru- ment cluster , illuminates when the transfer case is shifted to the 4 FULL TIME position. The 4LO MODE indicator light, located on the instru- ment ...

  • Jeep Liberty (2005) - page 242

    Proper operation of 4-wheel drive vehicles depends on tires of equal size, type, and cir cumference on each wheel. Any differ ence will adversely affect shifting and can cause damage to the transfer case. W ARNING! • Because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faste ...

  • Jeep Liberty (2005) - page 243

    N Neutral - Disengages both the front and r ear driveshafts from the powertrain. T o be used for flat towing behind another vehicle. Refer to “Recreational T owing” in Sec- tion 5 for more information. 4LO Part T ime 4–Wheel Drive Low Range - Low speed 4–wheel drive. Locks the transfer case inter-axle dif fer- ential. Forces the fr ont and ...

  • Jeep Liberty (2005) - page 244

    shifting. This will allow full engagement of the newly selected position. Apply a constant force when shifting the transfer case lever . 4 FULL TIME to 4 LO or 4 LO to 4 FULL TIME W ith the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to N (Neutral). While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift th ...

  • Jeep Liberty (2005) - page 245

    TRAC-LOK™ REAR AXLE — IF EQUIPPED The optional T rac-Lok™ rear axle pr ovides a constant driving force to both r ear wheels and reduces wheel spin caused by the loss of traction at one driving wheel. If traction differs between the two r ear wheels, the differ - ential automatically proportions the usable tor que by providing mor e torque to ...

  • Jeep Liberty (2005) - page 246

    T o release the parking brake, pull up slightly , press the center button, then lower the lever completely . Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the P (Park) position. Make certain the transfer case is in gear . Failure to do so may cause the vehicle to ro ...

  • Jeep Liberty (2005) - page 247

    ANTI-LOCK BRAKE SYSTEM — IF EQUIPPED The Anti-Lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate com- puter to modulate hydraulic pressur e to prevent wheel lock-up and help avoid skidding on slippery surfaces. All vehicle wheels and tires must be th ...

  • Jeep Liberty (2005) - page 248

    W ARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop. W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it incre ...

  • Jeep Liberty (2005) - page 249

    CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioni ...

  • Jeep Liberty (2005) - page 250

    where additional low speed pulling power is needed. V ehicle speeds in excess of 25 mph (40 km/h) should be avoided when in 4L or 4LO range. Driving Through W ater Although your vehicle is capable of driving through water , there ar e a number of precautions that must be considered befor e entering the water: CAUTION! When driving through water , d ...

  • Jeep Liberty (2005) - page 251

    Standing W ater A void driving in standing water deeper than 20 inches, and reduce speed appr opriately to minimize wave ef- fects. Maximum speed in 20 inches of water is less than 5 mph (8 km/h). Maintenance After driving through deep water , inspect your vehicle fluids and lubricants (engine oil, transmission oil, axle, transfer case) to assure t ...

  • Jeep Liberty (2005) - page 252

    your speed. If the brakes are r equired to contr ol vehicle speed, apply them lightly and avoid locking or skidding the tires. W ARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. T o do so may result in tipping and rolling the vehicle. Always back care- fully straig ...

  • Jeep Liberty (2005) - page 253

    After Driving Off-Road Off-r oad operation puts more str ess on your vehicle than does most on-road driving. After going off-r oad it is always a good idea to check for damage. That way you can get any problems taken car e of right away and have your vehicle ready when you need it. • Completely inspect the underbody of your vehicle. Check tires, ...

  • Jeep Liberty (2005) - page 254

    TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards. T ires designed to this standar d have ...

  • Jeep Liberty (2005) - page 255

    T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar ds T = T emporary Spare tir e 31 = Overall Diameter in Inches (in) 215 = Section W idth in Milimeters (mm) 65 = A ...

  • Jeep Liberty (2005) - page 256

    EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be a ...

  • Jeep Liberty (2005) - page 257

    Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tir es as mounted on the vehicle. If the ...

  • Jeep Liberty (2005) - page 258

    Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar . For vehicles other than passenger cars, the cold tire inflation pr essures ar e listed on either the shutface of the driver’s door , ...

  • Jeep Liberty (2005) - page 259

    T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pr essures for the fr ont, rear and spare tir es. Loading The vehicle maximum load on th ...

  • Jeep Liberty (2005) - page 260

    combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight refer enced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the ...

  • Jeep Liberty (2005) - page 261

    ST ARTING AND OPERA TING 261 5 ...

  • Jeep Liberty (2005) - page 262

    W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Proper tir e inflation pressur e is essential to the safe and satisfactory operation of y ...

  • Jeep Liberty (2005) - page 263

    2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under inflation also increases tire r olling resistance and r esults in higher fuel consump- tion. 3. Ride Comfort and V ehicle Stabilit ...

  • Jeep Liberty (2005) - page 264

    more often if subject to a wide range of outdoor tempera- tures, as tir e pressur es vary with temperature changes. Inflation pressur es specified on the label are always “Cold Inflation Pressur e.” Cold inflation pressur e is defined as the tire pr essure after the vehicle has been idle for at least 3 hours, or driven less than a mile after a ...

  • Jeep Liberty (2005) - page 265

    Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial tires in sets of four . Never combine them with other types of tires. Cuts and punctures in radial tir es are r epairable only in the tread ar ea beca ...

  • Jeep Liberty (2005) - page 266

    T read Wear Indicators These indicators are narr ow strips 1/16 inch (1.6 mm) thick and are found in the tr ead pattern grooves. When the tread pattern is worn down to these tr eadwear indicators, the tires should be r eplaced. Overloading your vehicle, long trips in very hot weather , and driving on bad roads may r esult in greater wear . Replacem ...

  • Jeep Liberty (2005) - page 267

    W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unap- proved tires and wheels may change suspension dimen- sions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering ...

  • Jeep Liberty (2005) - page 268

    T ires may also cause the vehicle to pull left or right. Alignment will not correct this pr oblem. See your dealer for proper diagnosis of the pr oblem. Improper alignment will not normally cause vehicle vibration, which may be a result of tir e and wheel out-of-balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear ...

  • Jeep Liberty (2005) - page 269

    The system will consist of tire pr essure monitoring sensors attached to each wheel through the valve stem mounting hole, a central receiver module and an amber colored Indicator Lamp. A sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare wheel and tir e assembly . NOTE: For vehicles with optional wheel/t ...

  • Jeep Liberty (2005) - page 270

    CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor . NOTE: • The TPM system can inform the driver of a low tire pressur e condition. • The TPM system is not intended to replace normal tir e care ...

  • Jeep Liberty (2005) - page 271

    system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. The T ire Pressur e Monitoring System consists of the following components: • Receiver Module • 4/5 Wheel Sensors • 4 Wheel Sensor T rigger Modules • T ire Pressur e Monitoring System Display Messages in the EVIC • Am ...

  • Jeep Liberty (2005) - page 272

    NOTE: The Indicator Lamp will only illuminate for the four active road tir es. A low spare tire pr essure will not cause the Indicator Lamp to illuminate When the appropriate conditions exist, the Electr onic V ehicle Information Center (EVIC) displays the following messages. LEFT FRONT , LEFT REAR, RIGHT FRONT , RIGHT REAR LOW PRESSURE, SP ARE LOW ...

  • Jeep Liberty (2005) - page 273

    CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor . NOTE: • The TPM system can inform the driver of a low tire pressur e condition. • The TPM system is not intended to replace normal tir e care ...

  • Jeep Liberty (2005) - page 274

    TIRE CHAINS CAUTION! T o avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indic ...

  • Jeep Liberty (2005) - page 275

    TIRE ROT A TION RECOMMENDA TIONS T ires on the front and r ear axles of vehicles operate at differ ent loads and perform differ ent steering, handling, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be r educed by timely rotation of tir es. The benefits of rotation ar e e ...

  • Jeep Liberty (2005) - page 276

    The suggested rotation method is the “forwar d-cross” shown in the following diagram. FUEL REQUIREMENTS (GASOLINE ENGINES) Y our engine is designed to meet all emis- sions regulations and pr ovide excellent fuel economy and performance when us- ing high quality unleaded gasoline having an octane rating of 87. The use of premium gasoline is not ...

  • Jeep Liberty (2005) - page 277

    Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and immediate service is requir ed. Poor quality gasoline can cause problems such as har d starting, stalling and hesitations. If you experience these symptoms, try another brand of gasoline before consid- erin ...

  • Jeep Liberty (2005) - page 278

    Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are r equired in some ar eas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasoline containing M ...

  • Jeep Liberty (2005) - page 279

    Materials Added T o Fuel All gasoline sold in the United States is requir ed to contain effective deter gent additives. Use of additional detergents or other additives is not needed under normal conditions. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Fede ...

  • Jeep Liberty (2005) - page 280

    Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed ar ea, such as a garage, and never sit in a parked vehic ...

  • Jeep Liberty (2005) - page 281

    NOTE: DaimlerChrysler Corporation recommends that this vehicle should be operated using Diesel fuel with 15 ppm Sulfur or less, where it is available. W ARNING! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel. Diesel fuel is seldom complete ...

  • Jeep Liberty (2005) - page 282

    The gas cap is located behind the fuel filler door , on the left side of the vehicle. If the gas cap is lost or damaged, be sure the r eplacement cap has been designed for use with this vehicle. When tightening the gas cap, tighten until 2 or 3 clicks are hear d to insure that the cap is pr operly seated. NOTE: A loose gas cap may cause the “Malf ...

  • Jeep Liberty (2005) - page 283

    Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “CHECK GAS CAP” message will be displayed in the EVIC (Electronic V ehicle Information Center). Refer to “Overhead Console” in Section 3 of this manual. T ighten the fuel filler cap properly and pr ...

  • Jeep Liberty (2005) - page 284

    Perform maintenance services as prescribed in the “Maintenance Schedules” section. When your vehicle is used for trailer towing, never exceed the gross axle weight rating (GA WR) by the addition of: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle. Remember that everything p ...

  • Jeep Liberty (2005) - page 285

    CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brake pedal effort, and longer stopping distances. W ARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overl ...

  • Jeep Liberty (2005) - page 286

    Minimum V ehicle Requirements for T railer T owing 286 ST ARTING AND OPERA TING ...

  • Jeep Liberty (2005) - page 287

    RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) T owing – 2WD Models Recreational towing is not allowed. T owing with the rear wheels on the gr ound can result in sever e transmis- sion damage. T owing — 4WD Models CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: The tr ...

  • Jeep Liberty (2005) - page 288

    5. Shift automatic transmission into D (Drive) or manual transmission into any forward gear . 6. Release brake pedal and ensure that there is no vehicle movement. 7. Shut the engine OFF and place the ignition key into the unlocked OFF position. 8. Shift automatic transmission into P (Park) or ensure manual transmission is in any forward gear . 9. A ...

  • Jeep Liberty (2005) - page 289

    5. Start engine. 6. Shift automatic transmission into D (Drive) or manual transmission into any forward gear . W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the N (Neutral) position without first fully engaging the parking brake. The transfer case N (Neutral) position disengages both the fro ...

  • Jeep Liberty (2005) - page 290

    W ARNING! Do not add a snow plow , winches, or any other aftermarket equipment to the front of your vehicle. This could adversely affect the functioning of the airbag system and you could be injured. 290 ST ARTING AND OPERA TING ...

  • Jeep Liberty (2005) - page 291

    WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flashers ................. 2 9 2 䡵 If Y our Engine Overheats ................. 2 9 3 䡵 Jacking And T ire Changing ................ 2 9 4 ▫ Jack Location ........................ 2 9 5 ▫ Spare T ire Stowage .................... 2 9 5 ▫ Preparations For Jacking ................ 2 9 6 ...

  • Jeep Liberty (2005) - page 292

    HAZARD W ARNING FLASHERS Y our vehicle’s hazard warning flasher is an emer gency warning system. When you activate it, all front and r ear directional signals will flash intermittently . Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle. This is an emergency warning system, not ...

  • Jeep Liberty (2005) - page 293

    IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appr opriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N (Neutral), but do not increase engine idle speed. NOTE: There ar e steps that you can take to slow down an imp ...

  • Jeep Liberty (2005) - page 294

    If the coolant temperature of a vehicle equipped with a diesel engine approaches the “H” (hot mark) a warning chime will sound to alert the driver . The air conditioning system will turn off automatically and power loss will occur until the engine temperature r eturns to the normal range. If the overheating condition persists a continuous chime ...

  • Jeep Liberty (2005) - page 295

    Jack Location The scissor-type jack, and tir e changing tools are stored beneath the right rear seat. T o remove the jack from its stowage position, turn the thumb screw counter clock- wise to loosen jack assembly and then remove it. Spare Tire Stowage T o remove the spar e tire from the carrier , remove the tir e cover , if equipped, and remove th ...

  • Jeep Liberty (2005) - page 296

    NOTE: If you have added aftermarket accessories to the spare tir e mounted carrier , it cannot exceed a gross weight of 50 lbs (23 kg) including the weight of the spare tire. Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place auto- matic transmission in P (Park), or manual ...

  • Jeep Liberty (2005) - page 297

    4. Locate the jack as shown. For the front tires, place it in the notch on the body weld seam behind wheel to be changed. For the rear tir es, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw ...

  • Jeep Liberty (2005) - page 298

    W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install lug nuts with cone-shaped end toward wheel. L ...

  • Jeep Liberty (2005) - page 299

    JUMP ST ARTING PROCEDURE NOTE: Check the charge indicator on the battery . If the indicator is light or yellow , replace the battery . 1. W ear eye protection and r emove any metal jewelry such as watch bands or bracelets that might make an unintended electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle w ...

  • Jeep Liberty (2005) - page 300

    NOTE: T o start the vehicle following connection of a booster battery , the Security Alarm System must first be disabled by cycling a front door key cylinder or by using the keyless entry transmitter . W ARNING! Jump starting can be dangerous. T o avoid personal injury or damage to electrical components in vehicle, observe the following warnings: ? ...

  • Jeep Liberty (2005) - page 301

    W ARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. EMERGENCY T OW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, they are mounted in the front and the r ear . CAUTION! T ow hooks ar ...

  • Jeep Liberty (2005) - page 302

    TOWING A DISABLED VEHICLE 2WD Models Only Provided the transmission is operable, tow only in N (Neutral) at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). T owing at more than 30 mph (48 km/h) or for mor e than 15 miles (24 km) can cause severe transmission damage. If the transmission is not operable, or the ...

  • Jeep Liberty (2005) - page 303

    MAINT AINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine ........................... 3 0 6 䡵 3.7L Engine ........................... 3 0 7 䡵 2.8L T urbo Diesel Engine ................. 3 0 8 䡵 Onboard Diagnostic System — OBD II ........ 3 0 9 ▫ Loose Fuel Filler Cap Message ............ 3 0 9 䡵 Emissions Inspection And Maintenance Programs .. ...

  • Jeep Liberty (2005) - page 304

    ▫ Maintenance-Free Battery ................ 3 2 0 ▫ Air Conditioner Maintenance ............. 3 2 1 ▫ Power Steering Fluid Check .............. 3 2 2 ▫ Driveline And Steering Component Lubrication .......................... 3 2 2 ▫ Body Lubrication ..................... 3 2 3 ▫ W indshield W iper Blades ................ 3 2 3 ▫ W inds ...

  • Jeep Liberty (2005) - page 305

    䡵 Bulb Replacement ...................... 3 5 1 ▫ Head Light .......................... 3 5 1 ▫ Front T urn Signal ..................... 3 5 2 ▫ Front Fog Light (Fr ont Fascia Mounted) ..... 3 5 3 ▫ Light Bar ........................... 3 5 4 ▫ Rear T ail, Stop, T urn Signal, And Back-Up Lights ............................. 3 5 5 ▫ Ce ...

  • Jeep Liberty (2005) - page 306

    2.4L ENGINE 306 MAINT AINING YOUR VEHICLE ...

  • Jeep Liberty (2005) - page 307

    3.7L ENGINE MAINT AINING YOUR VEHICLE 307 7 ...

  • Jeep Liberty (2005) - page 308

    2.8L TURBO DIESEL ENGINE 308 MAINT AINING YOUR VEHICLE ...

  • Jeep Liberty (2005) - page 309

    ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems ar e operating properly , your vehicle will provide excellent performance and fuel economy , as wel ...

  • Jeep Liberty (2005) - page 310

    that the gas cap is properly tightened. Pr ess the odometer reset button to turn the message of f. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a r ow , the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem ...

  • Jeep Liberty (2005) - page 311

    5. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn of f the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all an ...

  • Jeep Liberty (2005) - page 312

    DEALER SERVICE Y our dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner . Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any pr ocedure yourself. NOTE: Intentional tampering with emissions c ...

  • Jeep Liberty (2005) - page 313

    The best time to check the engine oil level is about 5 minutes after a fully warmed engine has been shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level between the ADD and SAFE markings on the dipstick. ...

  • Jeep Liberty (2005) - page 314

    If ANY of these apply to you, then change your engine oil at every interval shown in schedule “B” of the “Mainte- nance Schedules” section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule “A” of the “Main- tenance Schedules” section of this manual NOTE: Under no circumsta ...

  • Jeep Liberty (2005) - page 315

    Engine Oil Selection (Diesel Engines) For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer r ecommends using synthetic engine oils that are API Certified (SL/CF), and meet the require- ments of DaimlerChrysler Material Standard MS-10725. Engine Oil V iscosity (2.8L Diesel Engines) Use ...

  • Jeep Liberty (2005) - page 316

    Disposing of Used Engine Oil Care should be taken in disposing of used engine oil fr om your vehicle. Used oil and oil filters, indiscriminately discarded, can pr esent a problem to the envir onment. Contact your authorized dealer , service station, or gov- ernmental agency for advice on how and where used oil can be safely discarded in your ar ea. ...

  • Jeep Liberty (2005) - page 317

    Spark Plugs Spark plugs must fire pr operly to assure engine perfor - mance and emission control. New plugs should be in- stalled at the mileage specified in the appropriate main- tenance chart. The entire set should be r eplaced if there is any malfunction due to a faulty spark plug. Refer to the “V ehicle Emission Control Information” label i ...

  • Jeep Liberty (2005) - page 318

    W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual situations involving grossly malfunctioning engine o ...

  • Jeep Liberty (2005) - page 319

    Engine Timing Belt — 2.4L Engine Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition Wiring System — 2.4L Engine Replace the ignition cables at the intervals described in the appropriate maintenance schedule. Crankcase Emission Control System Proper operation of this system depends on fr e ...

  • Jeep Liberty (2005) - page 320

    Maintenance-Free Battery Y our vehicle is equipped with a maintenance-free battery . Y ou will never have to add water , nor is periodic main- tenance requir ed. W ARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery . T o determine the battery charge, check the ba ...

  • Jeep Liberty (2005) - page 321

    CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. Also, if a “fast charger” is used while battery is in the vehicle, disconne ...

  • Jeep Liberty (2005) - page 322

    Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluor ocar- bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product. How- ever , the manufacturer r ecommends that air conditioning service be performed by dealers or other service facilities using recovery and r ecycling equ ...

  • Jeep Liberty (2005) - page 323

    “Maintenance Schedule” in Section 8 is very important, particularly if your vehicle is subjected to off-r oad or other heavy-duty use. See your authorized dealer for complete service information. Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, swing gate and hood hinges, should be lubricated periodi ...

  • Jeep Liberty (2005) - page 324

    Windshield W ashers The fluid reservoir for the windshield washers and the rear window washer is shar ed. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not antifreeze/coolant) and operate the system for a few s ...

  • Jeep Liberty (2005) - page 325

    have an authorized technician inspect the complete ex- haust system and adjacent body areas for br oken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil ...

  • Jeep Liberty (2005) - page 326

    Cooling System — Drain, Flush, And Refill At the intervals shown on the appropriate “Maintenance Schedule” the system should be drained, flushed, and refilled. If the coolant solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner (see your authorized dealer for recommendations). ...

  • Jeep Liberty (2005) - page 327

    Adding Engine Coolant Y our vehicle has been built with an improved antifr eeze/ coolant that allows extended maintenance intervals. This antifreeze/coolant can be used up to 5 Y ears or 100,000 miles before r eplacement. T o prevent reducing this ex- tended maintenance period, it is important that you use the same antifreeze/coolant thr oughout th ...

  • Jeep Liberty (2005) - page 328

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. W ARNING! The warning words DO NOT OPEN HOT on the cooling system pressure cap are a safety precaution. Never add antifreeze/coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat cause ...

  • Jeep Liberty (2005) - page 329

    When additional antifreeze/coolant is needed to main- tain the proper level, it should be added to the coolant recovery bottle. Do not overfill. Points T o Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the fr ont of the engine compartment. This is normally a result of moist ...

  • Jeep Liberty (2005) - page 330

    • Make sure that the radiator and coolant r ecovery bottle hoses are not kinked or obstr ucted. • Keep the front of the radiator clean. Also, if your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for summer or winter operation. If replacement is ever necessary , install ONL Y ...

  • Jeep Liberty (2005) - page 331

    W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou wouldn’t have your full braking capacity in an emergency . Brake and Power Steering System Hoses When ...

  • Jeep Liberty (2005) - page 332

    W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately . Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the “Brake W arning ...

  • Jeep Liberty (2005) - page 333

    Use only manufacturer’s r ecommended brake fluid, refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. W ARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking. Y ou could have an accident. W ARNI ...

  • Jeep Liberty (2005) - page 334

    CAUTION! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants, a ...

  • Jeep Liberty (2005) - page 335

    (cross-hatched ar ea) on the oil level indicator . The fluid level indicator should be in the COLD region at 70° F (21° C) fluid temperature. If the fluid level is low , add sufficient fluid to bring to the proper level. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid is added through the dipstick tube. NOT ...

  • Jeep Liberty (2005) - page 336

    Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water . If con- taminated with water , the fluid should be changed im- mediately . T ransfer Case Fluid Leve ...

  • Jeep Liberty (2005) - page 337

    CAUTION! When installing plugs, do not overtighten. Y ou could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s r ecommended fluid, refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. Front/Rear Axle Fluid The front axle has a thr eaded “fill plug” on the cover plate, and a thre ...

  • Jeep Liberty (2005) - page 338

    hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under - body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corr osion resistance built into your vehicle. What Causes Corrosion? Corrosion is the r esult of deterioration or removal of pai ...

  • Jeep Liberty (2005) - page 339

    CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the under carriage at least once a month. • It is important that the drain holes in the lower edges of the ...

  • Jeep Liberty (2005) - page 340

    • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar 威 T ouch Up Paint on scratches or chips as soon as possible. Y our authorized dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar 威 Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar ? ...

  • Jeep Liberty (2005) - page 341

    cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instr u- ments which may scratch the elements. When cleaning the rear view mirr or , spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirr or . Carpet V acuum your carpet regularly to pr event a soil build-up. ...

  • Jeep Liberty (2005) - page 342

    vegetation or brush that could become a fir e hazard, or conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. CAUTION! Under frequent heavy-duty driving conditions, change all lubricants and lubricate body compo- nents, all driveline joints and steering linkage more often than in normal service to prevent excessive we ...

  • Jeep Liberty (2005) - page 343

    Cavity Fuse Description 1 15 Amp Blue Horn Relay , Power Sunroof Relay , Power W indow Relay 2 10 Amp Red Rear Fog Lights (Export Only) 3 20 Amp Y el- low Cigar Lighter 4 10 Amp Red Headlight Low Beam Right 5 10 Amp Red Headlight Low Beam Left 6 20 Amp Y el- low Body Control Module/Power Door Locks 7 10 Amp Red Left Park Light/Left T ail Lamp/Licen ...

  • Jeep Liberty (2005) - page 344

    Cavity Fuse Description 19 20 Amp Y el- low Frt Fog Lights/T railer T ow Stop and T urn Lights 20 Spare 21 10 Amp Red Radio 22 20 Amp Y el- low Power Sunroof Relay/ Antenna Module (Export Only) 23 Spare 24 10 Amp Red PDC Blower Motor 25 10 Amp Red Heated Seat Switches/HV AC Control Head/T railer T ow Battery Charge 26 10 Amp Red Headlight High Beam ...

  • Jeep Liberty (2005) - page 345

    Cavity Fuse Description 38 10 Amp Red ABS Contr oller/Shifter As- sembly 39 10 Amp Red Hazard Flasher (T urn Signals)/Backup Lamp Switch (Manual T ransmission Only)/T ransmission Range Switch (Automatic T ransmis- sion Only) Underhood Fuses (Power Distribution Center) Y our vehicle is equipped with an electrical power distri- bution center located ...

  • Jeep Liberty (2005) - page 346

    Cavity Fuse Description F3 50 Amp Red JB Power F4 40 Amp Green ABS Pump F5 20 Amp Y el- low NGC T rans F6 30 Amp Pink ASD F7 50 Amp Red JB Power F8 40 Amp Green Ign/Start F9 50 Amp Red JB Power F10 30 Amp Pink T railer T ow F1 1 Open F12 30 Amp Pink Light Bar F13 40 Amp Green W indows F14 40 Amp Green Ignition Switch Cavity Fuse Description F15 50 ...

  • Jeep Liberty (2005) - page 347

    Cavity Fuse Description F27 Open F28 15 Amp Blue Starter R29 Half ISO Re- lay Fuel Pump R30 Half ISO Re- lay Starter R31 Half ISO Re- lay W iper On/Off R32 Half ISO Re- lay W iper Hi/Lo R33 Full ISO Re- lay H. Blower R34 Full ISO Re- lay Rad. Fan Hi R35 Half ISO Re- lay A/C Clutch R36 Open Cavity Fuse Description R37 Half ISO Re- lay NGC T rans R38 ...

  • Jeep Liberty (2005) - page 348

    Cavity Fuse Description F5 Open F6 30 Amp Pink ASD F7 50 Amp Red JB Power F8 40 Amp Green Ign/Start F9 50 Amp Red JB Power F10 30 Amp Pink T railer T ow F1 1 20 Amp Y el- low Fuel Heater F12 30 Amp Pink Light Bar F13 40 Amp Green W indows F14 40 Amp Green Ignition Switch F15 50 Amp Red JB Power F16 15 Amp Blue ASD Feed F17 Open Cavity Fuse Descript ...

  • Jeep Liberty (2005) - page 349

    Cavity Fuse Description R30 Half ISO Re- lay Starter R31 Half ISO Re- lay W iper On/Off R32 Half ISO Re- lay W iper Hi/Lo R33 Full ISO Re- lay H. Blower R34 Full ISO Re- lay Rad. Fan Hi R35 Half ISO Re- lay A/C Clutch R36 Half ISO Re- lay V iscous Heat R37 Open R38 Open Cavity Fuse Description R39 Full ISO Re- lay ASD R40 Full ISO Re- lay Rad. Fan ...

  • Jeep Liberty (2005) - page 350

    air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. REPLACEMENT BULBS Interior Lights Bulb T ype A/C Heater .................... N o t S e r viceable Ashtray Receiver Light .... ...

  • Jeep Liberty (2005) - page 351

    BULB REPLACEMENT Head Light 1. Open the hood. 2. Reach behind the headlamp unit in the engine com- partment to access the headlamp bulb lock ring. 3. Firmly grasp the lock ring on the back of the headlamp unit housing. 4. Rotate the lock ring on the back of the headlamp housing counter-clockwise to unlock it. CAUTION! Do not touch the new bulb with ...

  • Jeep Liberty (2005) - page 352

    Front T urn Signal 1. Remove the screw fr om the turn signal/park lamp unit. 2. Pull the inboard side of the lamp away enough to disengage the tab that secures the outboar d side of the lamp from the slot in the fr ont bumper fascia. 3. Rotate the bulb socket counter-clockwise to unlock it. CAUTION! Do not touch the new bulb with your fingers. Oil ...

  • Jeep Liberty (2005) - page 353

    Front Fog Light (Front Fascia Mounted) 1. Remove the thr ee screws from the backside of the lamp housing. 2. Pull the bezel and lens away from the lamp housing far enough to access and disconnect the wiring connector from the bulb pigtail wir e. 3. Pinch together the two hooked ends of the bulb retainer clip and disengage them fr om the slots in th ...

  • Jeep Liberty (2005) - page 354

    Light Bar 1. Remove the screws from the light bar cover . 2. Remove the light bar cover . 3. Disconnect wiring harness from bulb socket. 4. Rotate the socket on the back of the lamp housing counter-clockwise to unlock it. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in co ...

  • Jeep Liberty (2005) - page 355

    Rear T ail, Stop, T urn Signal, and Back-Up Lights 1. Open the swing gate. 2. Remove the two T orx fasteners. 3. Remove rear lamp assembly . 4. Rotate the socket on the back of the lamp housing counter-clockwise to unlock it. 5. Replace the bulb. Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. T wist the bulb ...

  • Jeep Liberty (2005) - page 356

    FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 20.5 Gallons 78 Liters Engine Oil with Filter 2.4/3.7 Liter Engines (SAE 5W -30, API Certified Engine Oil) 5 Qts 4.7 Liters 2.8 Liter Diesel Engine (SAE 0W -40 Mobil 1 威 Synthetic, API Certified Engine Oil) 6.4 Qts 6.1 Liters Cooling System * 2.4 Liter Engine (Mopar 威 Antifreeze/Coolant 5 Y ear/1 ...

  • Jeep Liberty (2005) - page 357

    RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil (2.4L and 3.7L Engines) Use API Certified SAE 5W -30 Engine Oil, meeting the requirements of DaimlerChrysler Material S ...

  • Jeep Liberty (2005) - page 358

    Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid Manual T ransmission Mopar 威 Manual T ransmission Lubricant or equivalent (meeting the re- quirements of DaimlerChrysler Material Standar d MS-9224) T ransfer Case Mopar 威 A TF+4 Automatic T ransmission Fluid Axle Differ en ...

  • Jeep Liberty (2005) - page 359

    MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 6 0 䡵 Maintenance Schedules — Gasoline Engines .... 3 6 0 ▫ Schedule “B” — Gasoline Engines ......... 3 6 3 ▫ Schedule “A” — Gasoline Engines ......... 3 7 3 䡵 Maintenance Schedules — Diesel Engines ..... 3 7 8 ▫ Schedule “B” — Diesel E ...

  • Jeep Liberty (2005) - page 360

    EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliab ...

  • Jeep Liberty (2005) - page 361

    • T axi, police, or delivery service (commercial service). • Off-r oad or desert driving. • If equipped for and operated with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “Schedule B” of the “Maintenance Schedules” section ...

  • Jeep Liberty (2005) - page 362

    At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will impr ove the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent, add as requir ed. On ...

  • Jeep Liberty (2005) - page 363

    Schedule “B” — Gasoline Engines Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32°F (0°C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than ...

  • Jeep Liberty (2005) - page 364

    Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the fr ont and rear axle fluid‡ X 364 ...

  • Jeep Liberty (2005) - page 365

    Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary . 〫 ...

  • Jeep Liberty (2005) - page 366

    Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the fr ont and rear axle fluid‡ X ...

  • Jeep Liberty (2005) - page 367

    Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) Change the engine oil and engine oil filter , if not replaced at 3 months. XXXXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary . 〫 X ...

  • Jeep Liberty (2005) - page 368

    Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (101 000) (106 000) (110 000) (1 15 000) (120 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the fr ont and rear axle fluid ...

  • Jeep Liberty (2005) - page 369

    Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary ...

  • Jeep Liberty (2005) - page 370

    Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the fr ont and rear axle flui ...

  • Jeep Liberty (2005) - page 371

    Miles 108,000 11 1,000 1 14,000 1 17,000 120,000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Change the engine oil and engine oil filter , if not replaced at 3 months. XXXXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if nece ...

  • Jeep Liberty (2005) - page 372

    Miles 108,000 11 1,000 1 14,000 1 17,000 120,000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Inspect the drive belt and replace as needed. Not r equired if belt was previously r eplaced. X Drain and refill the transfer case fluid. X Flush and replace the engine coolant/anti-fr eeze at 120 months, if not replaced at 102,000 miles ...

  • Jeep Liberty (2005) - page 373

    Schedule “A” — Gasoline Engines Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [Months] [6] [12] [18] [24] [30] Change the engine oil and engine oil filter . X X X X X Rotate the tires. X X X X X Inspect the engine air filter element, and replace if necessary . X Replace the spark plugs. X In ...

  • Jeep Liberty (2005) - page 374

    Miles 36,000 42,000 48,000 54,000 (Kilometers) (58 000) (67 000) (77 000) (86 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the brake linings. X X 374 SCHEDULE “A” — GASOLINE ENGINES 8 M A I N T E N A N C E S C H E D U L E S ...

  • Jeep Liberty (2005) - page 375

    Miles 60,000 66,000 72,000 78,000 (Kilometers) (96 000) (106 000) (1 15 000) (125 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if nec- essary . X Replace the spark plugs. X Inspect the ignition cables, and replace if necessary (2. ...

  • Jeep Liberty (2005) - page 376

    Miles 84,000 90,000 96,000 102,000 (Kilometers) (134 000) (144 000) (154 000) (163 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if nec- essary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary . 〫 X ...

  • Jeep Liberty (2005) - page 377

    Miles 108,000 1 14,000 120,000 (Kilometers) (173 000) (182 000) (192 000) [Months] [108] [1 14] [120] Change the engine oil and engine oil filter . X X X Rotate the tires. X X X Inspect the engine air filter element, and replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary . 〫 X Inspect the ignition ...

  • Jeep Liberty (2005) - page 378

    MAINTENANCE SCHEDULES — DIESEL ENGINES There ar e two maintenance schedules that show the required service for your vehicle. First is Schedule ⴖ B ⴖ . It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures ar e below 32°F (0°C). • Stop and go driv ...

  • Jeep Liberty (2005) - page 379

    At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will impr ove the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent, add as requir ed. On ...

  • Jeep Liberty (2005) - page 380

    Schedule “B” — Diesel Engines Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32°F (0°C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than 50 ...

  • Jeep Liberty (2005) - page 381

    Miles 6,250 12,500 18,750 25,000 31,250 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element. Replace as necessary . X X XXX Replace the engine air filter element. XX Inspect the boost pressur e solenoid filter . Replace as necessary . X X XXX Replace ...

  • Jeep Liberty (2005) - page 382

    Miles 37,500 43,750 50,000 56,250 62,500 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element. Replace as necessary . X X XXX Replace the engine air filter element. XX X Inspect the boost pressur e solenoid filter . Replace as necessary . X X XXX Rep ...

  • Jeep Liberty (2005) - page 383

    Miles 68,750 75,000 81,250 87,500 93,750 100,000 (Kilometers) (1 10 000) (120 000) (130 000) (140 000) (150 000) (160 000) Change the engine oil and engine oil filter . X X X X X X Inspect the engine air filter element. Re- place as necessary . XXX X X X Replace the engine air filter element. XX X Inspect the boost pressur e solenoid filter . Re- p ...

  • Jeep Liberty (2005) - page 384

    Miles 68,750 75,000 81,250 87,500 93,750 100,000 (Kilometers) (1 10 000) (120 000) (130 000) (140 000) (150 000) (160 000) Inspect the brake linings. X X Drain and refill the fr ont and rear axle fluid. X X 〫 Applies only if vehicle is used for frequent trailer towing, or fleet/commercial service. † The replacement of such component is r equest ...

  • Jeep Liberty (2005) - page 385

    Schedule “A” — Diesel Engines Miles 12,500 25,000 37,500 50,000 (Kilometers) (20 000) (40 000) (60 000) (80 000) Change the engine oil and engine oil filter . X X X X Inspect the engine air filter element. Replace as neces- sary . XXX X Replace the engine air filter element. XX Inspect the boost pressur e solenoid filter . Replace as nec- ess ...

  • Jeep Liberty (2005) - page 386

    Miles 62,500 75,000 87,500 100,000 (Kilometers) (100 000) (120 000) (140 000) (160 000) Change the engine oil and engine oil filter . X X X X Inspect the engine air filter element. Replace as neces- sary . XX X X Replace the engine air filter element. XX Inspect the boost pressur e solenoid filter . Replace as nec- essary . XX X X Replace the boost ...

  • Jeep Liberty (2005) - page 387

    Miles 62,500 75,000 87,500 100,000 (Kilometers) (100 000) (120 000) (140 000) (160 000) Replace the engine accessory drive belt. X Inspect the brake linings. X X Inspect the transfer case fluid. X † The replacement of such component is r equested if there is superficial wear , bearing clearance, or evident grease leak. Inspection and service shou ...

  • Jeep Liberty (2005) - page 388

    ...

  • Jeep Liberty (2005) - page 389

    IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 3 9 0 ▫ Prepar e For The Appointment ............ 3 9 0 ▫ Prepar e A List ........................ 3 9 0 ▫ Be Reasonable W ith Requests ............. 3 9 0 䡵 If Y ou Need Assistance ................... 3 9 0 䡵 ...

  • Jeep Liberty (2005) - page 390

    SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s ...

  • Jeep Liberty (2005) - page 391

    technicians, special tools, and the latest information to assure your vehicle is fixed corr ectly and in a timely manner . This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the deale ...

  • Jeep Liberty (2005) - page 392

    Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center . Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the U ...

  • Jeep Liberty (2005) - page 393

    W ARRANTY INFORMA TION See your manufacturer’s W arranty Information Booklet for information on warranty coverage and transfer of warranty . IF YOU NEED CONSUMER ASSIST ANCE 393 9 ...

  • Jeep Liberty (2005) - page 394

    U.S. ONL Y 394 IF YOU NEED CONSUMER ASSIST ANCE ...

  • Jeep Liberty (2005) - page 395

    MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immedi ...

  • Jeep Liberty (2005) - page 396

    PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover or ders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street addr ess is required when or dering manuals. (No P .O. Boxes). • ...

  • Jeep Liberty (2005) - page 397

    Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .daimlerchrysler .com • www .daimlerchrysler .ca/manuals IF YOU NEED CONSUMER ASSIST ANCE 397 9 ...

  • Jeep Liberty (2005) - page 398

    ...

  • Jeep Liberty (2005) - page 399

    INDEX 10 ...

  • Jeep Liberty (2005) - page 400

    ABS (Anti-Lock Brake) System ............ 170,247 Adding W asher Fluid ..................... 1 5 7 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 319 Air Conditioner Maintenance ............... 3 2 1 Air Conditioning, Operating T ips ............ 2 1 4 Air Conditioning Refrigerant ............... 3 2 2 Air Filter ........................... ...

  • Jeep Liberty (2005) - page 401

    Bar , Light .......................... 121,354 Battery ............................... 3 2 0 Emergency Starting ..................... 2 9 9 Keyless T ransmitter Replacement ............ 2 9 Saving Feature (Pr otection) ............... 1 2 0 Belts, Drive ............................ 3 1 6 Body Mechanism Lubrication ............... 3 2 3 B-Pillar Loc ...

  • Jeep Liberty (2005) - page 402

    Caution, Exhaust Gas ................... 73,141 CD Changer ........................ 187,193 CD Player .................. 184,189,191,195,198 CD Player Maintenance ................... 2 1 1 Cellular Phone ........................ 85,21 1 Center High Mounted Stop Light ............ 3 5 5 Chains, T ire ............................ 2 7 4 Changing A Fla ...

  • Jeep Liberty (2005) - page 403

    Selection of Coolant .................. 326,356 T emperature Gauge ..................... 1 7 1 Crankcase Emission Control System .......... 3 1 9 Cruise Contr ol (Speed Control) .............. 1 2 7 Cruise Light ........................... 1 7 2 Cup Holder ............................ 1 5 0 Customer Assistance ..................... 3 9 0 Cylinder , ...

  • Jeep Liberty (2005) - page 404

    Electronic Thr ottle Control W arning Light ...... 1 7 5 Electronic V ehicle Information Center ......... 1 3 1 Emergency , In Case of Freeing V ehicle When Stuck ............... 2 3 6 Hazard W arning Flasher ................. 2 9 2 Jacking ............................. 2 9 4 Jump Starting ......................... 2 9 9 T ow Hooks ................ ...

  • Jeep Liberty (2005) - page 405

    Exhaust Gas Caution ................... 73,280 Exhaust System ......................... 3 2 4 Exterior Finish Care ...................... 3 3 8 Filters Air Cleaner .......................... 3 1 9 Engine Oil ........................... 3 1 6 Finish Care ............................ 3 3 8 Flashers Hazard W arning ....................... 2 9 2 T urn ...

  • Jeep Liberty (2005) - page 406

    Requirements ................... 276,280,356 T ank Capacity ........................ 3 5 6 Fuel System Caution ................... 279,283 Fuses ................................ 3 4 2 Garage Door Opener ..................... 1 3 9 G a s C a p ........................... 281,309 Gasoline .............................. 2 7 6 Gasoline, Reformulated .. ...

  • Jeep Liberty (2005) - page 407

    Identifying Y our Engine ................ 306,307 Ignition K e y ................................. 1 4 W iring System ........................ 3 1 9 Illuminated Entry ........................ 1 9 Inflation Pressur e T ires .................... 2 6 3 Information Center , V ehicle ................. 1 3 1 Inside Rearview Mirror .................... 8 ...

  • Jeep Liberty (2005) - page 408

    Anti-Lock ........................... 1 7 0 Back-Up ............................. 3 5 5 Battery Saver ......................... 1 2 0 Brake W arning ........................ 1 7 3 Bulb Replacement ...................... 3 5 1 C a r g o ............................ 1 17,151 Center Mounted Stop ................... 3 5 5 Cruise ....................... ...

  • Jeep Liberty (2005) - page 409

    T ransmission W arning ................... 1 7 2 T urn Signal .................. 1 19,168,352,355 W arning (Instrument Cluster Description) ..... 1 6 8 Loading V ehicle T i r e s ............................... 2 5 8 Locks Automatic Door ........................ 2 3 Child Protection ........................ 2 4 Door ................................ ...

  • Jeep Liberty (2005) - page 410

    Heated .............................. 8 4 Outside .............................. 8 2 Rearview ............................. 8 1 V anity ............................... 8 4 Modifications/Alterations, V ehicle ............. 9 Monitor , T ire Pressur e System ............... 2 6 8 Mopar Parts ......................... 3 1 1,395 Multi-Function Control ...

  • Jeep Liberty (2005) - page 411

    Owner’s Manual ........................ 3 9 6 Paint Care ............................. 3 3 7 Paint Damage .......................... 3 3 7 Panic Alarm ............................ 2 7 Parking Brake .......................... 2 4 5 Passing Light ........................... 1 1 9 PCV V alve ............................ 3 1 9 Pets .................. ...

  • Jeep Liberty (2005) - page 412

    Rear W iper/W asher ...................... 1 5 6 Rearview Mirrors ........................ 8 1 Reclining Front Seats ..................... 1 0 9 Recommended Fluids, Lubricants and Genuine Parts ............................... 3 5 7 Recreational T owing ...................... 2 8 7 Shifting into T ransfer Case Neutral (N) ....... 2 8 7 Shifting out ...

  • Jeep Liberty (2005) - page 413

    Seat Belts Adjustable Upper Shoulder Anchorage ........ 4 3 And Pregnant W omen ................... 4 7 Child Restraint ....................... 63,70 Extender ............................. 4 8 Inspection ............................ 7 4 Maintenance .......................... 3 4 1 Operating Instructions ................... 3 9 Pretensioners ....... ...

  • Jeep Liberty (2005) - page 414

    Snow Plow ............................ 2 8 9 Spare T ire ............................. 2 9 5 Spark Plugs ............................ 3 1 7 Specifications Fuel ................................ 2 7 6 O i l .............................. 314,315 Speed Control .......................... 1 2 7 Speedometer ........................... 1 6 8 Starting .... ...

  • Jeep Liberty (2005) - page 415

    T iming Belt ............................ 3 1 9 T ire and Loading Information Placard ...... 258,259 T ire Identification Number (TIN) ............. 2 5 7 T ire Markings .......................... 2 5 4 T ire Safety Information .................... 2 5 4 T i r e s ................................. 2 6 2 Air Pressur e .......................... 2 6 ...

  • Jeep Liberty (2005) - page 416

    Maintenance ....................... 333,335 Manual ............................. 2 2 7 Shifting ............................. 2 2 7 W arning Light ........................ 1 7 2 T ransmitter Battery Service .................. 2 9 T ransmitter , Garage Door Opener ............ 1 3 9 T ransmitter Programming ................... 2 8 T ransporting Pets ...

  • Jeep Liberty (2005) - page 417

    W ind Buffeting .......................... 3 6 W indow Fogging ........................ 2 1 4 W indows .............................. 3 5 Power ............................... 3 5 W indshield W ashers ...................... 1 2 4 Fluid ............................... 3 2 4 W indshield W iper Blades .................. 3 2 3 W indshield W ipers ..... ...

  • Jeep Liberty (2005) - page 418

    NOTES ...

  • Jeep Liberty (2005) - page 419

    NOTES ...

  • Jeep Liberty (2005) - page 420

    NOTES ...

  • Jeep Liberty (2005) - page 421

    NOTES ...

  • Jeep Liberty (2005) - page 422

    NOTES ...

  • Jeep Liberty (2005) - page 423

    NOTES ...

  • Jeep Liberty (2005) - page 424

    NOTES ...

Manufacturer Jeep Category Car

Documents that we receive from a manufacturer of a Jeep Liberty (2005) can be divided into several groups. They are, among others:
- Jeep technical drawings
- Liberty (2005) manuals
- Jeep product data sheets
- information booklets
- or energy labels Jeep Liberty (2005)
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jeep Liberty (2005).

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jeep Liberty (2005), service manual, brief instructions and user manuals Jeep Liberty (2005). Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jeep Liberty (2005).

Similar manuals

A complete manual for the device Jeep Liberty (2005), how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jeep Liberty (2005) by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jeep Liberty (2005).

A complete Jeep manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jeep Liberty (2005) - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jeep Liberty (2005), FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jeep Liberty (2005), that we can find in the current document
3. Tips how to use the basic functions of the device Jeep Liberty (2005) - which should help us in our first steps of using Jeep Liberty (2005)
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jeep Liberty (2005)
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jeep Liberty (2005) in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jeep Liberty (2005)?

Use the form below

If you did not solve your problem by using a manual Jeep Liberty (2005), ask a question using the form below. If a user had a similar problem with Jeep Liberty (2005) it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)