English dropdown-ico

Manual Weed Eater WE261

40 pages 8.04 mb
Download

Go to site of 40

Summary
  • Weed Eater WE261 - page 1

    Operator’s Manual 532 43 32-03 Rev . 10 26" RIDING MOWER SIDE DISCHARGE ELECTRIC ST ART IMPORT ANT : Read and follow all Safety Rules and Instructions before operating this equipment. Catalog No. WE261 Patents P ending ...

  • Weed Eater WE261 - page 2

    2 T ABLE OF CONTENTS WARRANTY Warranty ................................................. 2 Safety Rules ........................................... 3 Product Specifications ............................ 6 Assembly/Pre-Operation ........................ 7 Operation .............................................. 10 Maintenance Schedule ............... ...

  • Weed Eater WE261 - page 3

    3 SAFETY RULES DANGER: This cutting machine is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury or death. I. GENERAL OPERA TION • Read,understand,andfollowallinstruc - tions on the machine and in the manual before starting. • Do? ...

  • Weed Eater WE261 - page 4

    4 SAFETY RULES II. SL OPE OPERA TION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mowupanddownslopes (15°Max),not acro ...

  • Weed Eater WE261 - page 5

    5 SAFETY RULES • Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner . Always place containers on the ground away from your vehicle when filling. • Remove gas-powered equ ipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel ...

  • Weed Eater WE261 - page 6

    6 UNASSEMBLED P ARTS PRODUCT SPECIFICA TIONS CUSTOMER RESPONSIBILITIES • Readandobservethesafetyrules. • Follow a regular schedule in maintaining, caring for and using your riding mower . • F ollow the instructions under “Mainte - nance” and “Storage” sections of thi ...

  • Weed Eater WE261 - page 7

    7 Y our new riding mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. T o ensure safe and proper operation of your riding mower all parts and hardware you assemble must be tightened securely . Use the correct tools as necessary to insure proper tightness. ASSEMBL Y/PRE-OPERA TION TOOLS ...

  • Weed Eater WE261 - page 8

    8 NOTE: Y ou may now roll your riding mower off the skid. Follow the appropriate instruction below to remove the riding mower from the skid. CHECK TIRE PRESSURE The tires on your riding mower were overinflated at the factory for shipping pur - poses. Correct tire pressure is important for best cutting performance. • Reducetirepressure ...

  • Weed Eater WE261 - page 9

    9  CHECKLIST Before you operate your new riding mower , we wish to assure that you receive the best performance and satisfaction from this Quality Product. Please review the following checklist:  All assembly instructions have been completed.  No remaining loose parts in carton.  Battery is properly connected.  Seat is adjusted comfo ...

  • Weed Eater WE261 - page 10

    10 OPERA TION These symbols may appear on your riding mower or in literature supplied with the prod- uct. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY OVER TEMP LIGHT KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF OIL PRESSURE FUEL CHOKE MOWER HEIGHT PARK ...

  • Weed Eater WE261 - page 11

    11 KNOW YOUR RIDING MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR RIDING MOWER Compare the illustrations with your riding mower to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Our riding mowers conform to the applicable safety standards of the Ameri ...

  • Weed Eater WE261 - page 12

    12 The operation of any riding mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your riding mower or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. 00155 HOW TO USE YOUR ...

  • Weed Eater WE261 - page 13

    13 TO OPERA TE MOWER Y our riding mower is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the deck clutch engaged will shut off the engine. Y ou must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your ...

  • Weed Eater WE261 - page 14

    14 ADD GASOLINE • Fillfuel tankto bottomof fillerneck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used withi ...

  • Weed Eater WE261 - page 15

    15 MOWING TIPS • Mower should be properly leveled for best mowing performance.  See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are ...

  • Weed Eater WE261 - page 16

    16 MAINTENANCE IMPORT ANT : Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self-lubricating bearings. If you feel they must be lubricated, use only a dry , powdered graphite type lu- bricant sparingly . GENERAL RECOMMENDA TIONS The warranty on ...

  • Weed Eater WE261 - page 17

    17 RIDING MOWER Always observe safety rules when performing any maintenance. BRAKE OPERA TION If riding mower requires more than four (4) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake mustbe serviced. (See “TOADJUST BRAKE” in the Service and Adjustments section of this m ...

  • Weed Eater WE261 - page 18

    18 BA TTERY Y our riding mower has a battery charging system which is sufficient for normal use. • Keepbatteryandconnectorsclean. •  Only recharge  battery with charger  approved for a 12V 2.8 amp. hour battery . • Charging with any other charger or an automotive style charger can cause ...

  • Weed Eater WE261 - page 19

    19 MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SP ARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICA TIONS”? ...

  • Weed Eater WE261 - page 20

    20 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Placedeckclutchin“DISENGAGED”position. 4. T urnignitionkeyto“STOP ”andremo ...

  • Weed Eater WE261 - page 21

    21 TO LEVEL MOWER HOUSING Adjust the mower while riding mower is parked on level ground or driveway . Make sure tires are properly inflated (See side of tire for proper PSI). If tires are over or underinflated, you will not properly adjust your mower . SIDE- TO-SIDEADJUSTMENT • Raisemowertoitshighestposition. • Measur ...

  • Weed Eater WE261 - page 22

    22 TO ADJUST BRAKE Y our riding mower is equipped with an adjustable brake system which is mounted on the right side of the transaxle. If riding mower requires more than (4) feet stop- ping distance in highest gear on a lever dry concrete or paved surface, then brake must be adjusted. 1. Park riding mower on a level surface. 2. Release brake/parkin ...

  • Weed Eater WE261 - page 23

    23 F ender Battery Battery Bracket 1. Lift seat for bolt access. 2. Disconnect BL ACK battery cable then RED battery cable. 3. Remove battery bracket bolt. 4. Install new battery with terminals facing to the right, and away from seat as shown. 5. Reinstall battery bracket and bolt. 6. First connect RED battery cable to posi- tive (+) battery termin ...

  • Weed Eater WE261 - page 24

    24 STORAGE Immediately prepare your riding mower for storage at the end of the season or if the riding mower will not be used for 30 days or more. WARNING: Never store the riding mower with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. MOWER Remove deck ...

  • Weed Eater WE261 - page 25

    25 PROBLEM CAUSE CORRECTION Will not start 1 Out of fuel. 1 Fill fuel tank. 2 Bad spark plug. 2 Replace spark plug. 3 Dirty air filter . 3 Clean/replace air filter . 4 Water in fuel. 4 Empty fuel tank and carburetor , refill tank with fresh gasoline and replace fuel filter . 5 Loose or damaged wiring. 5 Check all wiring. 6 Engine valves out of adju ...

  • Weed Eater WE261 - page 26

    26 PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with atta- chment clutch engaged 1 F aulty operator-safety presence control system. 1 Check wiring, switches and connections. If not corrected, contact a qualified service center . Poor cut - uneven cutting 1 Worn, bent or loose blade. 1 Replace blade. Tighten blade bolt. ...

  • Weed Eater WE261 - page 27

    27 RIDING MOWER - -CA T ALOG NO . WE261 SCHEMA TIC BATTERY FUSE-40A RED RED WHITE BLACK/WHITE RED GREEN YELLOW BLACK/WHITE BLACK BLACK GRAY BLACK RELAY M STARTER CLUTCH / BRAKE (PEDAL UP) SEAT SWITCH (NOT OCCUPIED) IGNITION UNIT S M B G A1 A2 L REVERSE SWITCH SPARK PLUG GAP NOT IN REVERSE SHORTING CONNECTOR ATTACHMENT CLUTCH (CLUTCH OFF) REMOVABLE ...

  • Weed Eater WE261 - page 28

    28 RIDING MOWER - -CA T ALOG NO . WE261 ELECTRICAL 11 LRV1 10 9 8 12 13 7 1 2 3 4 6 5 ...

  • Weed Eater WE261 - page 29

    29 RIDING MOWER - -CA T ALOG NO . WE261 ELECTRICAL 1 532 43 70-70 BA TTERY 2 532 42 54-16 FOAM, POL YURETHANE 3 532 19 33-50 SWITCH, IGN, DL T A , P -IN, ROS 4 532 41 19-33 KEY , MOLDED ENGLISH/SP ANISH - - 532 41 19-35 KEY , MOLDED ENGLISH/FRENCH/INTERNA TIONAL 5 532 43 33-30 FUSE, 5A 6 532 42 59-37 FUSE, 40A 7 532 16 07-84 SWITCH, PLUNGER, NO , O ...

  • Weed Eater WE261 - page 30

    30 RIDING MOWER - -CA T ALOG NO . WE261 CHASSIS 10 11 3 4 5 7 9 8 1 2 12 13 49 14 15 16 17 18 19 20 21 22 23 24 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 39 40 40 41 41 42 43 44 45 45 50 50 45 45 45 45 45 45 6 46 46 45 45 45 46 48 46 48 46 46 47 LRV-Chassis_1_r2 ...

  • Weed Eater WE261 - page 31

    31 RIDING MOWER - -CA T ALOG NO . WE261 CHASSIS 1 532 42 80-48 WELDMENT , CHASSIS 2 532 42 82-47 SUPPORT , AXEL LH 3 532 42 82-44 SUPPORT , AXEL RH 4 532 42 83-46 SHIELD, TRANSAXLE FRONT 5 532 42 81-10 BRACE, AXLE CROS S 6 532 42 81-09 COVER, FRICTION DRIVE 7 532 42 80-40 PL A TE, ENGINE 8 532 42 85-76 BRACKET , CHASSIS FRONT 9 532 42 88-56 BRACKET ...

  • Weed Eater WE261 - page 32

    32 RIDING MOWER - -CA T ALOG NO . WE261 DRIVE LRV-Drive_1_r3 10 11 11 3 1 2 2 3 4 5 6 7 72 8 8 1 2 2 3 4 5 6 7 8 73 8 12 13 13 70 70 14 14 15 71 15 16 17 18 19 20 21 22 23 24 24 25 26 27 28 29 30 31 32 33 34 35 36 37 37 38 38 38 39 40 41 42 43 70 45 46 47 48 49 50 51 52 53 54 55 56 57 58 58 58 70 70 70 59 70 70 70 60 61 62 63 63 64 64 65 66 67 68 6 ...

  • Weed Eater WE261 - page 33

    33 KEY P ART NO. NO . DESCRIPTION KEY P ART NO. NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm RIDING MOWER - -CA T ALOG NO . WE261 DRIVE – – 532 43 61-44 SERVICE KIT , TRANSAXLE 1 532 43 64-98 WHEEL ASM (REAR) 2 532 12 17-48 WASHER, 16 GA . 3 812 00 00-01 E-CLIP 4 532 12 35-83 KEY . SQUARE 5 532 42 79-39 ...

  • Weed Eater WE261 - page 34

    34 RIDING MOWER - -CA T ALOG NO . WE261 STEERING 10 11 2 2 4 6 6 7 7 9 9 9 1 2 30 3 1 2 30 3 4 4 5 29 8 8 8 12 13 14 15 16 17 18 19 19 20 21 22 28 23 24 25 26 27 LRV-Steering_1_r2 ...

  • Weed Eater WE261 - page 35

    35 RIDING MOWER - -CA T ALOG NO . WE261 STEERING 1 532 43 65-00 WHEEL ASM (FRONT) 2 812 00 00-01 E-CLIP 3 532 18 89-67 WASHER, HARDENED 4 532 12 17-49 WASHER, 1/4 X 3/4 5 532 42 80-34 SPINDLE, RH 6 532 12 49-31 WASHER, HARDENED THRUST 7 532 12 49-37 BUSHING, STEERING COL UMN 8 532 42 10-76 PIN, 5/64 X 3/4 COTTER 9 819 13 14-14 WASHER 10 532 42 80-5 ...

  • Weed Eater WE261 - page 36

    36 RIDING MOWER - -CA T ALOG NO . WE261 MOWER DECK 10 11 1 2 3 4 5 7 9 8 12 13 41 14 15 16 16 17 17 17 40 17 45 18 18 19 19 19 19 20 20 21 22 23 42 24 25 26 27 27 28 29 30 31 32 33 34 35 36 37 37 38 39 39 LRV-Deck_1_r4 44 43 46 6 36 ...

  • Weed Eater WE261 - page 37

    37 RIDING MOWER - -CA T ALOG NO . WE261 MOWER DECK 1 532 42 81-93 DECK, 26" 2 532 19 28-70 MANDREL ASM 3 532 43 25-20 KEEPER, BEL T 4 532 43 25-94 PULLEY , MANDREL 5 532 42 85-78 BEL T 6 532 42 82-42 COVER, MANDREL 7 532 42 93-95 LIFT ASM, DECK 8 532 42 91-95 LINK, DECK LIFT 9 5324293-97 LINK,ADJUST ABLE 10 532 43 89-23 DEFLECTO ...

  • Weed Eater WE261 - page 38

    38 RIDING MOWER - -CA T ALOG NO . WE261 DECALS 1 532 43 05-88 DECAL, STEERING WHEEL 2 532 43 35-96 DECAL, V -BEL T SCH 30" 3 532 42 51-13 DECAL, WARN. DEFLECT/CTFGR 4 532 43 05-89 DECAL, DECK/DEFLECTOR 5 532 43 44-57 DECAL, WARNING ENGINEGUARD 6 532 43 53-48 DECAL, STRBRCKT INST ALL BOOT - - 532 43 24-79 DECAL, B YP AS S - - 532 43 32-03 MANU ...

  • Weed Eater WE261 - page 39

    39 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Weed Eater WE261 - page 40

    10.04.10 CL Printed in the U.S.A. This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. For P arts and service, contact our authorized distributor: call 1-800-849-1297 • Forreplaceme ...

Manufacturer Weed Eater Category Lawn Mower

Documents that we receive from a manufacturer of a Weed Eater WE261 can be divided into several groups. They are, among others:
- Weed Eater technical drawings
- WE261 manuals
- Weed Eater product data sheets
- information booklets
- or energy labels Weed Eater WE261
All of them are important, but the most important information from the point of view of use of the device are in the user manual Weed Eater WE261.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Weed Eater WE261, service manual, brief instructions and user manuals Weed Eater WE261. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Weed Eater WE261.

Similar manuals

A complete manual for the device Weed Eater WE261, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Weed Eater WE261 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Weed Eater WE261.

A complete Weed Eater manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Weed Eater WE261 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Weed Eater WE261, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Weed Eater WE261, that we can find in the current document
3. Tips how to use the basic functions of the device Weed Eater WE261 - which should help us in our first steps of using Weed Eater WE261
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Weed Eater WE261
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Weed Eater WE261 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Weed Eater WE261?

Use the form below

If you did not solve your problem by using a manual Weed Eater WE261, ask a question using the form below. If a user had a similar problem with Weed Eater WE261 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)