English dropdown-ico

Manual Powercom 425A

17 pages 0.05 mb
Download

Go to site of 17

Summary
  • Powercom 425A - page 1

    U P S Uninterruptible Power System Line Interactive UPS 325A/425A/525A/625A Line Interactive Network UPS 425AP/525AP/625AP USER ‘ S MANUAL ...

  • Powercom 425A - page 2

    Important safety instructions __________________________________________________________ _____ Thank you for selecting this uninterruptible power system (UPS). It provides you with better protection for connected equipment. Please read this manual! This manual provides safety, installation and operating instructions that will help you derive the fu ...

  • Powercom 425A - page 3

    Table of contents __________________________________________________________ ____ 1. Introduction ……… ……… ………… ……… … ..1 2. Safety ………… …………… ………… ………… 2 3. Presentation Front Panel. … ……………… ……………… 3 Rear Panel. ………… …………… ………… .4 4. I ...

  • Powercom 425A - page 4

    1. INTRODUCTION __________________________________________________________ _____ The product is line interactive UPS with the newest technology and powerful function. The LINE INTERACTIVE ups is with AVR function allows input voltage range from 75% to 125%, including on line voltage boost-up & buck down. An ideal protection equipment for critic ...

  • Powercom 425A - page 5

    2. Safety __________________________________________________________ _____ CAUTION ! ● To reduce the risk of electric shock, disconnect the UPS from the mains supply before installing a computer interface signal cable. Reconnect the power cord only after signaling interconnections have been made. ● T he internal energy source(the battery) canno ...

  • Powercom 425A - page 6

    3. Presentation __________________________________________________________ ____ FRONT PANEL 3.1 "REPLACE BATTERY" indicator (RED LED) The LED illuminates when the UPS's battery is no longer useful and must be replaced. Note : When replace battery, disconnect the utility power then open the case and take notice of the battery's p ...

  • Powercom 425A - page 7

    __________________________________________________________ __ REAR PANEL 3.5 COMPUTER INTERFACE (425AP/525AP/625AP models only) Provide both RS-232 and relay signal to support NOVELL, UNIX, DOS, WINDOWS and other operating systems. 3.6 OUTPUT POWER RECEPTACLES 3.7 AC INPUT POWER RECEPTACLE 3.8 TEL./MODEM SURGE PROTECTION (425AP/525AP/625AP models o ...

  • Powercom 425A - page 8

    4. Installation __________________________________________________________ ____ 4.0 Inspection Inspect the UPS upon receipt. The packaging is recyclable; save it for reuse or dispose of it properly. 4.1 Placement Install the UPS in a protected area with adequate air flow and free of excessive dust. Do not operate the UPS where the temperature and h ...

  • Powercom 425A - page 9

    4.5 Connect the loads Plug the loads into the output connectors on the rear of the UPS. To use the UPS as a master on/off switch, make sure all of the loads are switched on. Caution: Never connect a laser printer or plotter to the UPS with other computer equipment. A laser printer or plotter periodically draws significantly more power than when idl ...

  • Powercom 425A - page 10

    5. Operation __________________________________________________________ ____ 5.1 Switch on With the UPS plugged in, press and hold the on/off/test/silence button more than 1 second until "LINE NORMAL" LED lit to switch the ups on. The UPS will perform self-testing each time when it is switched on. Note : When switched off the UPS maintain ...

  • Powercom 425A - page 11

    6. Alarm __________________________________________________________ _____ 6.1 "BACK UP" (slow alarm) When in BACK UP mode, the YELLOW LED illuminates and the UPS sounds an audible alarm. The alarm stops when the UPS returns to LINE NORMAL operation. Press the on/off/test/silence button during on-battery alarms to stop the beeping. 6.2 &qu ...

  • Powercom 425A - page 12

    7. Software options __________________________________________________________ ____ 7.1 UPSMON Software The UPSMON software is applied standard RS-232 interface to perform monitoring functions, and then provides an orderly shutdown of a computer in the event of power failure. Moreover, UPSMON displays all the diagnostic symptoms on monitor, such as ...

  • Powercom 425A - page 13

    8. Computer Interface Port __________________________________________________________ ____ The computer interface port has the following characteristics: ...

  • Powercom 425A - page 14

    9. Battery Replacement __________________________________________________________ ____ Your battery should run any where from 3-5 years before eve needing to be replaced. Please follow the instructions below for easy battery replacement. 1) Unplug unit from AC power source and disconnect all connected equipment. 2) Disconnect AC power cord from uni ...

  • Powercom 425A - page 15

    10. Troubleshooting __________________________________________________________ ____ PROBLEM POSSIBLE CAUSE ACTION TO TAKE On/off/test/silence button not pushed or push too short Press the on/off/test/silence button more than 1 second Battery voltage less than 10V Recharge the ups at least 4 hours PCB failure Replace the PCB, call for service UPS no ...

  • Powercom 425A - page 16

    11. Storage __________________________________________________________ ____ 10.1 Storage conditions Store the UPS covered and upright in a cool , dry location, with its battery fully charged. Before storing, charger the UPS for at least 4 hours. Remove any accessories in the accessory slot and disconnect any cables connected to the computer interfa ...

  • Powercom 425A - page 17

    Typical Recharge Time 4 hours (to 90% of full capacity) Protection Automatic self-test & discharge protection, replace battery indicator Back up Time 10 - 30 minutes (depending on computer load) Net Weight Kg(lbs) 4.7(10.4) 5.8(12.8) 6.2(13.7) 6.5(14.3) Shipping Weight Kg(lbs) 5.0(11.0) 6.1(13.4) 6.5(14.3) 6.9(15.2) Dimension(mm) WxDxH 97x260x1 ...

Manufacturer Powercom Category Power Supply

Documents that we receive from a manufacturer of a Powercom 425A can be divided into several groups. They are, among others:
- Powercom technical drawings
- 425A manuals
- Powercom product data sheets
- information booklets
- or energy labels Powercom 425A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Powercom 425A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Powercom 425A, service manual, brief instructions and user manuals Powercom 425A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Powercom 425A.

Similar manuals

A complete manual for the device Powercom 425A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Powercom 425A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Powercom 425A.

A complete Powercom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Powercom 425A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Powercom 425A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Powercom 425A, that we can find in the current document
3. Tips how to use the basic functions of the device Powercom 425A - which should help us in our first steps of using Powercom 425A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Powercom 425A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Powercom 425A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Powercom 425A?

Use the form below

If you did not solve your problem by using a manual Powercom 425A, ask a question using the form below. If a user had a similar problem with Powercom 425A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)