English dropdown-ico

Manual Bryant 362AAN

12 pages 0.16 mb
Download

Go to site of 12

Summary
  • Bryant 362AAN - page 1

    NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. Index Page SAFETY CONSIDERATIONS ..................................................1-2 Minimum Clearance to Combustibles ......................................2 INTRODUCTION ............................................ ...

  • Bryant 362AAN - page 2

    Only the latest issues of above codes should be used, and are available from either The National Fire Protection Agency, Bat- terymarch Park, Quincy, MA 02269 or The Canadian Standards Association, 178 Rexdale Blvd., Rexdale, Ontario M9W 1R3 Recognize safety information. This is the safety-alert symbol . When you see this symbol on the furnace and ...

  • Bryant 362AAN - page 3

    3. Caulking or sealants are applied to areas such as joints around window and door frames; between sole plates and floors; between wall-ceiling joints; between wall panels; at penetrations for plumbing, electrical, and fuel lines; and at other openings. If combustion and ventilation air must be supplied to an uncon- fined space from outside, an ope ...

  • Bryant 362AAN - page 4

    VENTING INSTRUCTIONS Venting of furnace should be to the outside and in accordance with local codes or requirements of local utility. OIL-FIRED APPLIANCES SHALL BE CONNECTED TO FLUES HAVING SUFFICIENT DRAFT AT ALL TIMES TO ENSURE SAFE AND PROPER OPERATION OF APPLIANCE. For additional venting information, refer to ANSI/NFPA 211 Chimney, Fireplaces, ...

  • Bryant 362AAN - page 5

    ELECTRICAL The appliance must be installed in accordance with current ANSI/NFPA 70 National Electrical Code, CSA C22.1 Canadian Electrical Code Part 1, and/or local codes. The control system depends on correct polarity of power supply. Connect HOT wire (H) and NEUTRAL wire (N) as shown in Fig. 7. A separate line voltage supply MUST be used with a f ...

  • Bryant 362AAN - page 6

    c. Tighten purge fitting. Allow oil to run to nozzle and fire burner. d. If purging takes longer than 30 sec and no flame has been established, burner stops. Push reset button on top of primary control to restart burner. e. For detailed information on operation of primary control, refer to instructions included with furnace. III. FAN ADJUSTMENT CHE ...

  • Bryant 362AAN - page 7

    The procedure for nozzle installation and/or replacement is out- lined in oil burner instruction manual which came with furnace. For ease of maintenance, the oiling procedure for burner motor, as outlined in burner manual, should be performed at this time. After replacement of nozzle, burner should be adjusted in accor- dance with Combustion Check ...

  • Bryant 362AAN - page 8

    17. Use a stiff brush and vacuum cleaner to clean inside of primary drum. CAUTION: Never use incendiary type cleaners (smoke sticks) for cleaning! WARNING: For all heat exchanger plates that have been removed, the gaskets MUST be replaced. Failure to replace gaskets could lead to heat exchanger leakage, sooting, and a hazardous condition which coul ...

  • Bryant 362AAN - page 9

    INSULATION INTERMEDIATE PANEL FILTER B A G D ELECTRICAL CONNECTIONS OIL INLET F 12 1 ⁄ 16 ″ EH 1 ″ INSULATION PARTITION PANEL SUPPLY DUCT CLEAN-OUT PORTS RETURN DUCT 1 ″ 3 ″ C A96309 DIMENSIONS (IN.) UNIT SIZE UNIT DIMENSIONS DUCT SUPPLY OPENING FLUE DIAMETER RETURN DUCT Width Depth Height AB C D E F G H 036105 22 52 ...

  • Bryant 362AAN - page 10

    Fig. 6—Barometric Damper Locations A95117 FIG. A FIG. G FIG. D FIG. L FIG. B FIG. C FIG. J FIG. H FIG. K POOR WRONG WRONG WRONG WRONG WRONG BAROMETRIC DAMPER LOCATIONS GOOD LOCATIONS BAD LOCATIONS —10— ...

  • Bryant 362AAN - page 11

    → Fig. 7—Wiring Diagram A96380 INDOOR BLOWER MOTOR BR BR CAP T GND LINE V 24 V LINE V 24 V BK BL BR GR OR RD RD/BK VI WH YL F T CAP AL L GND BLACK BLUE BROWN GREEN ORANGE RED RED/BLACK STRIPE VIOLET WHITE YELLOW LOW SPEED FAN SWITCH TRANSFORMER START ...

  • Bryant 362AAN - page 12

    USER’S INFORMATION I. HERE’S HOW YOUR HEATING SYSTEM WORKS The furnace operates automatically. It is controlled by a thermostat which you set at the temperature most comfortable to you. When the inside temperature drops below this setting, your thermostat will turn on heating system. When thermostat calls for heat, power from transformer energi ...

Manufacturer Bryant Category Furnace

Documents that we receive from a manufacturer of a Bryant 362AAN can be divided into several groups. They are, among others:
- Bryant technical drawings
- 362AAN manuals
- Bryant product data sheets
- information booklets
- or energy labels Bryant 362AAN
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bryant 362AAN.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bryant 362AAN, service manual, brief instructions and user manuals Bryant 362AAN. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bryant 362AAN.

Similar manuals

A complete manual for the device Bryant 362AAN, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bryant 362AAN by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bryant 362AAN.

A complete Bryant manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bryant 362AAN - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bryant 362AAN, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bryant 362AAN, that we can find in the current document
3. Tips how to use the basic functions of the device Bryant 362AAN - which should help us in our first steps of using Bryant 362AAN
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bryant 362AAN
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bryant 362AAN in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bryant 362AAN?

Use the form below

If you did not solve your problem by using a manual Bryant 362AAN, ask a question using the form below. If a user had a similar problem with Bryant 362AAN it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)