English dropdown-ico

Manual SkyLink SA-001S

20 pages 0.61 mb
Download

Go to site of 20

Summary
  • SkyLink SA-001S - page 1

    Model: SA-001S User’ s Instructions W ireless External Alarm ...

  • SkyLink SA-001S - page 2

    1 TABLE OF cONTENT INTRODUCTION ................................................................................................... INSTALLATION .............................................................................................. PROGRAMMING – LEARN REMOTE OR SENSORS OR CONTROL PANEL ....................... ERASE REMOTE OR SENSOR OR CON ...

  • SkyLink SA-001S - page 3

    2 INTrOducTION Congratulations on purchasing the Skylink Wireless External Alarm SA-001 Series. The SA-001 Series provide you with a piercing siren and powerful features yet ease to use. You will nd the installation to be simple and be able to get the unit up and running easily. The following items are included in this package: - One Wireless Ex ...

  • SkyLink SA-001S - page 4

    3 - Set Compatibility Jumper: Refer to the following table to setup the Wireless External Alarm to work with different Skylink’s Security System or Sensors. To select, you will see a jumper connector marked “J2” as shown below. Use a paper clip to remove the jumper connector and re-locate to the proper posts. - Insert 3 AA-size batteries (not ...

  • SkyLink SA-001S - page 5

    4 cAuTION: The adaptor as a disconnect devices: − the socket-outlet shall be installed near the equipment and shall be easily accessible. In order for the remote or sensor or control panel to communicate with the Exter- nal Wireless Alarm properly, this need be programmed into the Wireless External Alarm previously. Follow the brief instructions ...

  • SkyLink SA-001S - page 6

    5 3B – Learn motion sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the motion sensor by pressing the “Test/Set” button on the motion sensor. This “Test/Set” button is located inside the battery compartment. - ...

  • SkyLink SA-001S - page 7

    6 Mute button 3C – Learn door/window sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the Door/Window Sensor, by separating the magnets to send the signal. - You will hear 2 beeps and the LEDs will ash twice indicati ...

  • SkyLink SA-001S - page 8

    7 To erase unwanted remote(s) or sensor(s) or control panel(s) from the Wireless External Alarm will erase all learned devices from the Wireless External Alarm. - Press and hold the Learn/Set button on the Wireless External Alarm for 8 seconds. - While holding the Learn/Set button on the Wireless External Alarm until the Learn/Set LEDs turn on. You ...

  • SkyLink SA-001S - page 9

    8 The Wireless External Alarm can be programmed to react 2 arming sequences when it receives the signal from the sensor. In order to arm the Wireless External Alarm, the remote (optional) must be programmed to the Wireless External Alarm. You may arm the Wireless External Alarm in 2 different sequences: 6A – Arm Home Sequence: This setting is use ...

  • SkyLink SA-001S - page 10

    9 - You will hear 1 beep and the LEDs will ash once indicating the Wireless External Alarm is being counted to Away mode. - After 30 seconds, you will hear 2 beeps and the LEDs will ash twice indicating the Wireless External Alarm in Away mode. 6C – Disarm - Pressing the DISARM button on the remote will disarm the Wireless External Alarm in ...

  • SkyLink SA-001S - page 11

    10 The Wireless External Alarm is designed to work with the Skylink security control panel such as AM-001, ML-001 and SC-001. Put the control panel that you plan to program into programming mode. Refer to the User’s Instructions of that control panel. 7A – Learn control panel AM-001 or ML-001 to the Wireless External Alarm: - Press and hold the ...

  • SkyLink SA-001S - page 12

    11 You may connect your existing alarm system with the Wireless External Alarm so that the Wireless External Alarm will be triggered by your alarm system. There are 2 ways you can connect your Wireless External Alarm with your existing alarm system. The input terminals (INPUT1 or INPUT2) can be a Normally Open (NO) momentary dry contact or the DC v ...

  • SkyLink SA-001S - page 13

    12 You can enable or disable the Alert Notication. When it is set to enable, the Wireless External Alarm will beep when arm or disarm or during the entry/exit countdown period. When it is set to disable, the Wireless External Alarm will not beep when arm or disarm or during the entry/exit countdown period. However, the LED will remain ashing ...

  • SkyLink SA-001S - page 14

    13 When the battery power is being reduced, the Wireless External Alarm will emit 3 beeps when the remote arm or disarm the unit. It is time to replace the batteries or recharge the battery pack (rechargeable battery only) as soon as the low battery signal appears. Ensure all the batteries are replaced altogether at the same time. The Wireless Exte ...

  • SkyLink SA-001S - page 15

    14 Your Wireless External Alarm requires few simple maintenance to ensure its con - tinued reliability and operation. - The solar panel on the top housing should be cleaned using the soft and damp cloth. This will ensure the solar panel receives all the available light. - Test the Wireless External Alarm periodically to ensure the unit is working. ...

  • SkyLink SA-001S - page 16

    15 Questions Solutions Why the Wireless External Alarm does not respond to the sensors or remote? You must program the sensors or remote to the Wireless External Alarm before they can work together. Why I can’t arm my system? Make sure none of the sensors are trig- gered. For example, the door/window sensor should be in close status. Why isn’t ...

  • SkyLink SA-001S - page 17

    16 Fcc This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WArNINg: Changes or modications to this unit not expressly appro ...

  • SkyLink SA-001S - page 18

    17 WArrANTy If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization Number are required. Ic Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux ap- ...

  • SkyLink SA-001S - page 19

    18 cusTOmEr sErVIcE If you would like to - nd out the up-to-date specications - know more about features and applications - download documents, i.e. user’s instructions - order Skylink products or if you have difculty getting the products to work, please: 1. visit our FAQ section at www.skylinkhome.com, or 2. email us at support@skylinkh ...

  • SkyLink SA-001S - page 20

    19 101Y035 DEC,2012 ...

Manufacturer SkyLink Category Medical Alarms

Documents that we receive from a manufacturer of a SkyLink SA-001S can be divided into several groups. They are, among others:
- SkyLink technical drawings
- SA-001S manuals
- SkyLink product data sheets
- information booklets
- or energy labels SkyLink SA-001S
All of them are important, but the most important information from the point of view of use of the device are in the user manual SkyLink SA-001S.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals SkyLink SA-001S, service manual, brief instructions and user manuals SkyLink SA-001S. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product SkyLink SA-001S.

Similar manuals

A complete manual for the device SkyLink SA-001S, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use SkyLink SA-001S by users. Manuals are usually written by a technical writer, but in a language understandable to all users of SkyLink SA-001S.

A complete SkyLink manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual SkyLink SA-001S - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the SkyLink SA-001S, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the SkyLink SA-001S, that we can find in the current document
3. Tips how to use the basic functions of the device SkyLink SA-001S - which should help us in our first steps of using SkyLink SA-001S
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with SkyLink SA-001S
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of SkyLink SA-001S in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning SkyLink SA-001S?

Use the form below

If you did not solve your problem by using a manual SkyLink SA-001S, ask a question using the form below. If a user had a similar problem with SkyLink SA-001S it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)