English dropdown-ico

Manual Vista Ademco N7227V5

100 pages 0.65 mb
Download

Go to site of 100

Summary
  • Vista Ademco N7227V5 - page 1

    N7227V5 10/00 9 9 , , 6 6 7 7 $ $       6 6 ( ( 6HFXULW6VWHP  ,QVWDOODWLRQDQG6HWXS*XLGH • • • • • • • • • • • • • • • • • • • * ARMED READY PANIC OFF AWAY STAY MAX TEST BYPASS INSTANT CODE CHIME READY 1 2 3 6 5 4 89 7 0 * # ALARM CHECK FIRE AWAY STAY INSTANT BYPASS NO AC CHIME ...

  • Vista Ademco N7227V5 - page 2

    ii RECOMMENDATIONS FOR PROPER PROTECTION The following recom mendations for the location of fire and burg lary detection dev ices help provide proper coverag e for the protected premises. Recommendations f or Smoke and Heat Detectors With regard t o the number and pl acement of smok e/heat det ectors, we s ubscribe t o the recommen dations con tain ...

  • Vista Ademco N7227V5 - page 3

    iii Table of Contents •••••••••••••••••••••••••••••••••••••••••••••••••• SECTION 1. Introduction ......................................................................................................... ................... 1–1 Description ......... ...

  • Vista Ademco N7227V5 - page 4

    iv SECTION 11. Final Power-Up ...................................................................................................... .............. 11 – 1 Earth Ground Co nnections ....................................................................................................... ..................... 11-1 Wiring the AC Transfor mer ......... ...

  • Vista Ademco N7227V5 - page 5

    1–1 SECTION 1 Introduction •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Description ♦ Features •••••••••••••••••••••••••••••••••••••••••? ...

  • Vista Ademco N7227V5 - page 6

    VISTA -10SE Installat ion and Setup Guide 1-2 Security Codes • One Master code for ent ire system (Us er 2). Installer code is Us er 1. • 4 secon dary user co des ( User s 3 – 6). • One duress code (Us er 8). Duress Code: An emergency code that, when used to disarm or arm the system, will send a silent duress message to the c entral station ...

  • Vista Ademco N7227V5 - page 7

    Section 1 - Int roduction 1-3 Alarm Output • Provide s a 12VDC, 2 AMP outp ut that can driv e the compatible so unde rs listed in th e EXTERNAL SOUNDERS section (ass umes a fully charged battery is connected). • Steady o utput fo r burg lary/panic , or tem poral p ulse sou nding output f or fir e notif ication, as required by UL. • Uses curre ...

  • Vista Ademco N7227V5 - page 8

    VISTA -10SE Installat ion and Setup Guide 1-4 ...

  • Vista Ademco N7227V5 - page 9

    2 – 1 SECTION 2 Installing the Control •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Mounting the Cabinet ♦ Installing the Lock ♦ Mounting the Control's Circuit Board Alone in the Cabinet ♦ Mounting the Control a ...

  • Vista Ademco N7227V5 - page 10

    VISTA -10SE Installat ion and Setup Guide 2-2 Mounting the Control's Circuit Board Alone in the Cabinet To mount the ci rcuit boa rd alone in t he cabinet, follow thes e steps : 1. Hang two mounting clips* (prov ided) on the raised cabin et tabs (see Detail B in Figure 2 below) . 2. Insert the top of t he circuit board between the rows of slot ...

  • Vista Ademco N7227V5 - page 11

    Section 2 - Inst alling t he Control 2-3 MOUNTING CLIP CABINET DET AIL D ANTENNA AND GROUNDING LUG INST ALLA TION ANTENNA MOUNT (2 PLACES) ANTENNA (2) SCREW (2) MOUNTING CLIP CONTROL CIRCUIT BOARD BOARD SUPPORTING SLO TS HOLES FOR ANTENNAS AND GROUNDING LUGS RECEIVER CIRCUIT BOARD (See Detail D) + + + + RCVR BRD DET AIL A SIDE VIEW OF BOARD SUPPORT ...

  • Vista Ademco N7227V5 - page 12

    VISTA -10SE Installat ion and Setup Guide 2-4 TERMINALS ON CONTROL EARTH GROUND INCOMING TELECOM LINE HANDSET TIP RING RJ31X JACK PLUG DIRECT CONNECT CORD TIP RING GROUND PREMISES PHONES BROWN (TIP) GREY (RING) GREEN (TIP) RED (RING) 17 18 19 20 21 INCOMING TELECOM LINE V10SE-024-V0 Figure 4. Standa rd Telephone Li ne Connections ...

  • Vista Ademco N7227V5 - page 13

    3 – 1 SECTION 3 Remote Keypads •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Keypads That May Be Used ♦ Wiring to th e Keypad s ♦ Mounting the Keypads ♦ Supplementary Power for Additional Keypads ♦ Preliminary Check ...

  • Vista Ademco N7227V5 - page 14

    VISTA -10SE Installat ion and Setup Guide 3-2 Wiring Run Chart for Devic es* Drawing Aux Power From the Control ( 12V+ & 12V – ) TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED T O A SINGL E WIRE RUN Wire Size 50mA or less 100mA 300mA 500mA #22 500 ft (152m) 250 ft (76m) 80 ft (24m) 50 ft (15m) #20 750 ft (228.6m) 380 ft (116m) 130 ft (39.6m) 80 ...

  • Vista Ademco N7227V5 - page 15

    Section 3 - Inst alling Remote Keypads 3-3 Keypads powered fr om supplies that do not have a backup batter y will not function when AC power is lost. Therefore, be sure to power at least one keypad fr om the Control's aux iliary power output. Conne ct the add itional key pads as sho wn in Figure 6 , using the keypad wire colors shown. Be sure ...

  • Vista Ademco N7227V5 - page 16

    VISTA -10SE Installat ion and Setup Guide 3-4 If the “ Ready ” mess age is not displa yed on any of the k eypads in t he system, or a “ Not Ready ” messa ge is displayed, check the keypad wiring connections, and make sure each of the 6 basic hardw ired zon es has a 1000 oh m resistor co nnected across its terminals. Do not remove the EOL re ...

  • Vista Ademco N7227V5 - page 17

    4 – 1 SECTION 4 Basic Hardwired Zones 1 – 6 •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Installing the Hardwired Zones ♦ Programming Hardwired Zones ••••••••••••••••••••••? ...

  • Vista Ademco N7227V5 - page 18

    VISTA -10SE Installat ion and Setup Guide 4-2 3. To meet NFP A 72 req uirements, you must us e a supervisory module to supervise power (e.g., Sy stem Senso r No. A77-716B Re lay module ). + + 1000 OHMS EOLR HEAT DETECTOR HEAT DETECTOR ZONE 5 RED EOL POWER SUPERVISION RELAY MODULE A77-716B VIOLET 4-WIRE SMOKE OR COMBUSTION DETECTORS T O HI SIDE OF T ...

  • Vista Ademco N7227V5 - page 19

    5 – 1 SECTION 5 Wireless Expansion (5800 System) •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About Wireless Expansion ♦ Installing the 5881/5882 Receiver ♦ Installing the 5800TM Module ♦ About Jam Det ection and Rep ...

  • Vista Ademco N7227V5 - page 20

    VISTA -10SE Installat ion and Setup Guide 5-2 Installing the 5881/5882 Receiver RF System Installat ion Advisories Follow th e guide lines belo w whe n installing th e RF receiv er. (Disre gard if the receive r is mounted in the cont rol cabinet .) • Pla ce the RF receiver in a high, cent rally locat ed area for best reception. • Do not locate ...

  • Vista Ademco N7227V5 - page 21

    Section 5 - Wireless Expansion 5-3 Installing the 5800TM Module Installation of this module is necessary only if y ou are usin g one o r more 5827BD Wireless Bi-directio nal keyp ads, 5804 or 5804BD Tran smitters (wire less keys) . Mounting the 5800TM Module The 5800TM must be located n ext to th e RF receiv er (be tween one and two fe et fro m the ...

  • Vista Ademco N7227V5 - page 22

    VISTA -10SE Installat ion and Setup Guide 5-4 For button transmitters (RF ke ys), such as th e 5801, 5804, and 5804BD , you mu st assign a unique zone n umber to each in dividu al button u sed on th e transm itter. Each bu tton on the transmitter also h as a pre-d esignate d loo p or inp ut numbe r, which is au tomatically disp layed on the keypad ...

  • Vista Ademco N7227V5 - page 23

    Section 5 - Wireless Expansion 5-5 The wir eless sy stem can id entify a true lo w-batte ry situatio n, thus allo wing th e de aler or user of the s ystem ti me to arrange a cha nge of batt ery a nd mainta in protection for t hat point within th e syste m. Some transmitte rs (e.g., 5802, 5802CP, and 5804) contain lo ng-lif e but non replace able ba ...

  • Vista Ademco N7227V5 - page 24

    VISTA -10SE Installat ion and Setup Guide 5-6 5800 Series Transmitters Table ( c ontinued) Model Description Input Type and Special Notes 5817 (cont'd.) Multi-Point Universal Transmitter (cont'd.) DIP Switches: Set all DIP switches to the OFF position when enrolling the serial number. NOTE: All loops must be assigned the same input type. ...

  • Vista Ademco N7227V5 - page 25

    6 – 1 SECTION 6 Relay Output Devices •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Relay Device Basics ♦ 4204 Relay Modul es ♦ Programming Options •••••••••••••••••••••••• ...

  • Vista Ademco N7227V5 - page 26

    VISTA -10SE Installat ion and Setup Guide 6-2 4204 Setup 1 2 3 4 5 OF F ON ON The 4204 unit can be mounted either remo tely or in the control panel. Th e fo llowing steps should be taken to prop erly se t up the 4204: 1. Connect the 4204 t o the contr ol's remote k eypad ter minals (4 – 7), using the conne ctor supplied with the 4204. U se s ...

  • Vista Ademco N7227V5 - page 27

    7 – 1 SECTION 7 4285 and 4286 VIP Module •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Installing the VIP Module ♦ Programmin g the 4285/4286 VIP Mod ule ♦ Checking 4285/4286 VIP Mo dule Op eration ••••••• ...

  • Vista Ademco N7227V5 - page 28

    VISTA -10SE Installat ion and Setup Guide 7-2 VIP Module Wiring The VI P M odule is wired between the cont rol panel and t he premises handset(s ). It lis tens for touch-tones on t he phone line and report s them to t he control panel . During on-premises phone acces s, i t powers the premises phones; during off-premis es phone acces s, it seizes t ...

  • Vista Ademco N7227V5 - page 29

    Section 7 - 4285/4286 VIP Module 7-3 4285/4286 VIP Module W IRING NOTES : 1. Wire the VIP Module exact ly as shown, using a direc t-connect c ord and RJ31X jack . 2. If you do no hear tones when pr essing keys after ac cessing the secu rity system v ia an on-premises phone, try reversing t he pair of wir es connected t o terminals 3 and 4 on the V ...

  • Vista Ademco N7227V5 - page 30

    VISTA -10SE Installat ion and Setup Guide 7-4 Programming the Control for Phone Access To prog ram the con trol for ph one acce ss using the 4285/4286 VIP Module , you must assig n a VIP Module access code ( ✱ 26 ) a nd ring detection count ( ✱ 95). Also, you may optionally select words and/or form cus tom words th a t would be dis played on th ...

  • Vista Ademco N7227V5 - page 31

    8 – 1 SECTION 8 External Sounders •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Compatible Sounders ♦ NFPA Requirements ♦ Sounder Connections and Power ♦ Sounder Supervision ♦ Testing the Sounder ••••••? ...

  • Vista Ademco N7227V5 - page 32

    VISTA -10SE Installat ion and Setup Guide 8 – 2 Sounder Connections and Power The VISTA-10SE pr ovides a 12VD C output, w hich can po wer ex ternal alarm soun ders, be lls, or sirens (s ee tabl e of compatib le sounders on a previ ous page). T his output acti va tes a sounde r when an alarm occurs. Make conne ctions to alarm o utput termin als 3 ...

  • Vista Ademco N7227V5 - page 33

    9 – 1 SECTION 9 Long-Range Radio •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About L ong-Range Radio ♦ Wiring Connections ♦ Programming for Long-Range Radio ♦ Dynamic Signaling Feature •••••••••• ...

  • Vista Ademco N7227V5 - page 34

    VISTA -10SE Installat ion and Setup Guide 9-2 Dynamic Signaling Feature This VISTA-10SE control panel features Dynamic Signaling Delay (DSD) and Dynamic Signaling Priority (D SP) mes sage reporti ng when Long-Range Ra dio is us ed. Thes e message outp uts are ac cesse d thro ugh d ata fiel d ✱ 93. The Dy namic Signaling featur e is designed to re ...

  • Vista Ademco N7227V5 - page 35

    10 – 1 SECTION 10 Audio Alarm Verification (AAV) Unit •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About A udio Alarm Verificat ion ♦ Wiring Connections ••••••••••••••••••••••? ...

  • Vista Ademco N7227V5 - page 36

    VISTA -10SE Installat ion and Setup Guide 10-2 CONTROL/ DIALER HEADER NOTE: REFER TO AA V MODULE INSTRUCTIONS FOR CONNECTIONS TO AUDIO SPEAKERS AND MICROPHONE. • • • • • EA GLE 1250 4 5 18 17 19 20 21 DIP Switch 1 2 3 4 5 6 ON CONTROL EARTH GROUND RED (R) GREEN (T) GREY (R) BRO WN (T) INCOMING PHONE LINE RJ31X YELLOW RED BRO WN TIP RING E ...

  • Vista Ademco N7227V5 - page 37

    11 – 1 SECTION 11 Final Power-Up •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Earth Ground Connections ♦ Wiring the AC Transformer ♦ AC Power-Up ♦ Calculating the Battery Size Needed ♦ Connecting the Backup Battery ...

  • Vista Ademco N7227V5 - page 38

    VISTA -10SE Installat ion and Setup Guide 11-2 AC Power-Up To turn on AC power, perform the following s teps: 1. Plug the 1321/1321CN into a 24-hour, unsw itched 120VAC outlet. Followi ng power-up, one of the foll owi ng is dis played on t he keypad: AC , dI (disa bled); BUSY STANDBY (on alp ha keyp ads); or NOT READY (on fixed-word keypads ). The ...

  • Vista Ademco N7227V5 - page 39

    Section 11 – F inal Power-Up 11-3 Connecting the Backup Battery In the ev ent of an AC powe r loss, the co ntrol pane l is supporte d by a backup, re chargeable Sealed Le ad Acid battery. Th e range of battery sizes recomme nded are : 12VDC; 4AH- 17.2AH. See "Calculating the Battery Size Needed" earlier in th is section. Th e battery is ...

  • Vista Ademco N7227V5 - page 40

    VISTA -10SE Installat ion and Setup Guide 11-4 ...

  • Vista Ademco N7227V5 - page 41

    12 – 1 SECTION 12 Mechanics of Programming •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About P rogramming ♦ Entering Program Mode ♦ Progr ammi ng a D ata Fie ld ♦ Reviewing a Data Field/Erasing an Ent ry ♦ Interac ...

  • Vista Ademco N7227V5 - page 42

    VISTA -10SE Installat ion and Setup Guide 12-2 If a diffe rent Installer co de is subse quently pr ogrammed , use it instead o f 4111 to gain access to t he P rogramming mode. When you enter the P rogram mode, dat a field ✱ 20 is dis played (thi s is t he first da ta fiel d in the sy stem). The sy stem no w acc epts e ntries f or f ield ✱ 20. P ...

  • Vista Ademco N7227V5 - page 43

    13 – 1 SECTION 13 Zone Response Type Definitions •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Zone Type Definitions •••••••••••••••••••••••••••••••••••? ...

  • Vista Ademco N7227V5 - page 44

    VISTA -10SE Installat ion and Setup Guide 13-2 Type 05 Trouble by Day/ Alarm by Night Zone type 05 is usually a s signed to a zone that conta ins foil-prot ected doors or windows; or covers a sensi tive area (e.g., st ock room, drug su ppl y room, etc.) It ca n a lso be us ed on a sensor or cont act in an a rea where immedia te notifica tion of an ...

  • Vista Ademco N7227V5 - page 45

    Section 13 – Zone Response Type Definitions 13-3 Type 20 Arm – STAY Zone type 20 is a special-p urpose zone ty pe use d with 5800 Se ries wire less pushbu tton tran smitters. Zone Characterist ics: • Exit delay re gardless o f the arming mode se lected. • System is arm ed in th e STAY mod e whe n the zo ne is activ ated. • Zone number is ...

  • Vista Ademco N7227V5 - page 46

    VISTA -10SE Installat ion and Setup Guide 13-4 ...

  • Vista Ademco N7227V5 - page 47

    14-1 SECTION 14 Data Field Descriptions •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Descriptions of System Data Fields ••••••••••••••••••••••••••••••••••? ...

  • Vista Ademco N7227V5 - page 48

    VISTA -10SE Installat ion and Setup Guide 14-2 ✱ 26 VOIC E (PHONE) MODULE ACCESS CODE (2-Digit Entry) The use o f a 4285 or 4286 VIP (Pho ne) Mo dule re quires a 2- digit co de. Enter a 2-digit phone access code a s follows : For first digit, enter any digit from 1 to 9; for second digit, enter # +11 for ✱ , or # +12 for #. Example: If t he des ...

  • Vista Ademco N7227V5 - page 49

    Section 14 – Data Field Descriptions 14-3 ✱ 39 AUDIBLE EXIT WARNING (1-Digit Entry) If enabl ed, t his fiel d provides exit warning sound when a rmed AWAY or MAXI MUM. Warning s ound consist s of sl ow continuous beeps until l ast 5 seconds, when it change s to fast be eps. The warning sound will en d at the termination o f Exit time. 0 = no; 1 ...

  • Vista Ademco N7227V5 - page 50

    VISTA -10SE Installat ion and Setup Guide 14-4 For an ex planation o f these forma ts, s ee the SYSTEM COMMUNICATION section . ✱ 46 REPORT FORMAT (1-Digit Entry) Determine which format is to be used t o report to the central station. Ente r 1 digit (0 – 9). 0 = 3+1; 4+1 ADEMCO Lo Sp eed Stan dard (th is is the de fault) 1 = 3+1; 4+1 Radionics S ...

  • Vista Ademco N7227V5 - page 51

    Section 14 – Data Field Descriptions 14-5 A 10-digit code is s ent to the pager t hat is coded in the foll owing format: 4-digit Subscribe r No. SSSS – EEE – NNN 3 -dig it User or Zone No. (as entered i n field ✱ 43) 3-Digit Event Code (EEE), as follows: 911 = Alarm (NNN = Zone No.) 001 = Open, System disarmed (NNN = Us er No.) 002 = Close, ...

  • Vista Ademco N7227V5 - page 52

    VISTA -10SE Installat ion and Setup Guide 14-6 ✱ 52 ZONE 3 RESPONSE TIME TO OPEN (1-Digit Entry) 0 = 400mS nominal; 1 = 10mS no minal. ✱ 56 ZONE ASSIGNMENT/ALARM REPORT CODES This is an Interactiv e Menu mode th at is used to p rogram zone numbers , zone types , and alarm and report codes , and to identi fy the ty pe of lo op inpu t devic e . T ...

  • Vista Ademco N7227V5 - page 53

    Section 14 – Data Field Descriptions 14-7 SYSTEM STATUS REPORT CODES ( ✱ 60 – ✱ 68) ✱ 60 TRO UBLE REPORT CODE (See box abo ve.) (2-Digit Entry) ✱ 61 BYPAS S REPORT CODE (See box above .) (2-Digit Entry) ✱ 62 AC LOSS REPORT CO DE (See bo x above .) (2-Digit Entry) Reports wit h Subscriber No. Timing of this report is random wit h up to ...

  • Vista Ademco N7227V5 - page 54

    VISTA -10SE Installat ion and Setup Guide 14-8 RESTORE REPORT CODES ( ✱ 70 – ✱ 75) ✱ 70 ALARM RESTORE REPORT CODE (See box on previous page). For expanded or 4+2 reporting, a 2nd digit is automatically sent, and is the same as th e 2nd digit o f the zone Alarm Report code progra mmed i n field ✱ 56. ✱ 71 TR OUB LE RESTORE REPORT C ODE ( ...

  • Vista Ademco N7227V5 - page 55

    Section 14 – Data Field Descriptions 14-9 ✱ 93 DYNAMIC SIGNALING DELAY (DSD) ( 1st en try) This field enabl es you to s elect the t ime the panel should wait for acknowledgment from the first reporting dest inati on before it attempts to send a messag e to th e seco nd d estination . Delay s can be selecte d from 0 to 225 second s, in 15-seco n ...

  • Vista Ademco N7227V5 - page 56

    VISTA -10SE Installat ion and Setup Guide 14-10 Importan t Note: If “ 15 ” is entered in fiel d ✱ 95 to bypass an answ ering machine, and a 4285/4286 VIP Mod ule is includ ed in the installation , yo u sho uld note the follow ing: When calling in from an off-p remises phone (to receive a statu s report or exe cute a command), the user should ...

  • Vista Ademco N7227V5 - page 57

    15 – 1 SECTION 15 Zone Programming ( ✱ 56/ ✱ 58 Menu Mode) •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About Z one Programming ♦ ✱ 56 Zone Programming M ode Procedures ♦ ✱ 58 Expert Programming Mode Procedures ...

  • Vista Ademco N7227V5 - page 58

    VISTA -10SE Installat ion and Setup Guide 15 – 2 Zone Number 10 Zone Type Perimeter 03 Zone Type Zone Ty pe (ZT): Enter the Zone Type response (or change it, if necessary). Each zone must be assign ed to a zo ne type, w hich defines the way in which the sy stem re spond s to faults in that zone . Enter the Zone Type code (or change it, if neces s ...

  • Vista Ademco N7227V5 - page 59

    Section 15 - Z one Programming 15 – 3 10 INPUT S/N: L A022-4064 1 Note: The [A] and [B] ke ys may be u sed to mo ve the cursor to the r ight ( A) or le ft (B) withi n t he s erial number field, t hus allowi ng y ou to corr ect any e ntry e rror s that may have been m ade. Serial number Entry and Loop Number Entry. Used only when enrolling wireles ...

  • Vista Ademco N7227V5 - page 60

    VISTA -10SE Installat ion and Setup Guide 15 – 4 5800 Series Transmitter Input Loop Identification All of the transmitters illustrate d on this p age hav e one or more unique f actory- assigned input (loop) ID codes . Each of the i nput loops req uires i t s own programming z one (e.g., a 5804's four in put loo ps require f our pr ogramming ...

  • Vista Ademco N7227V5 - page 61

    Section 15 - Z one Programming 15 – 5 XMIT TO CONFIRM PRESS ✱ TO SKIP Confirmation Opt ion: This prompt appears only if you answered Yes to the first prompt in this section. T he syst em enters a confir mation mode s o that t h e opera tion of the actual pro gramme d inpu t can be co nfirme d. Activate the loo p inpu t or butto n that cor respo ...

  • Vista Ademco N7227V5 - page 62

    VISTA -10SE Installat ion and Setup Guide 15 – 6 ✱ 58 Expert Programming Mode Procedures Enter the P rogram mode and follow t he step-by-s tep ins tructions below. NOTE: Before proceeding, you must program fiel d ✱ 22 (RF Syste m) as require d. SET TO CONFIRM? 0 = NO 1 = YES 0 Press ✱ 58. This disp lay appe ars upon entry in to this mod e. ...

  • Vista Ademco N7227V5 - page 63

    Section 15 - Z one Programming 15 – 7 10 INPUT S/N: L A022-4064 1 Note: The [A ] and [ B] k ey s may be used t o move t he cursor to the r ight (A) or le ft (B) withi n t he s erial number field, t hus allowi ng you to correct any entry errors that may have been m ade. Serial Number entr y and Loop Number entry. Used only when enrolling wireless ...

  • Vista Ademco N7227V5 - page 64

    VISTA -10SE Installat ion and Setup Guide 15 – 8 To Remove a Zone To eithe r tempor arily or pe rmanently remove a zone f rom the 5800 system: 1. Enter the programming mode: Key Ins ta ller Code + 8 + 0 and press ✱ 56 . SET TO CONFIRM? 0 = NO 1 = YES 0 2. The displ a y at left appears . Enter 0 for No; 1 for Y es. Enter Zn Num. (00 = Quit) 10 3 ...

  • Vista Ademco N7227V5 - page 65

    Section 15 - Z one Programming 15 – 9 If you want to replac e t he serial number cont inue to step 4 ; otherwise, s kip to st ep 7 . A display f or the new transmitte r numbe r appe ars. 10 INPUT S/N: L A XXX - XXXX 1 4. Key th e transm itter. Th e new transmitte r serial n umber replac es the X ’ s in the d isplay. 5. The ne w summ ary disp la ...

  • Vista Ademco N7227V5 - page 66

    VISTA -10SE Installat ion and Setup Guide 15 – 10 10. If ne cessary , press th e [#] key to bac k up with out savi ng, and re- enter the serial number. If you are manuall y entering the seria l number, use the [A] k ey to mov e fo rward w ithin the scree n, and th e [B] ke y to m ove backward. XMIT TO CONFIRM PRESS ✱ TO SKIP 11. If you e ntered ...

  • Vista Ademco N7227V5 - page 67

    Section 15 - Z one Programming 15 – 11 Wireless Key Predefined Default Templates Y OU MUST PROGRAM THIS BUTTON LOOP 4 LOOP 3 ENROLL AS "BR" LOOP 1 LOOP 2 ON OFF LOOP 3 LOOP 1 LOOP 2 LOOP 4 (Y OU MUST PROGRAM THIS BUTTON) RED/YELLOW LED • • • • • • • • • • • • • • • • • • • GREEN/YELLOW LED ENROLL AS ...

  • Vista Ademco N7227V5 - page 68

    VISTA -10SE Installat ion and Setup Guide 15 – 12 ...

  • Vista Ademco N7227V5 - page 69

    16 – 1 SECTION 16 Output Device Programming ( ✱ 80 Menu Mode) •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Programming Options Defined ♦ Programming Output Devices •••••••••••••••••• ...

  • Vista Ademco N7227V5 - page 70

    VISTA -10SE Installat ion and Setup Guide 16 – 2 • TRO UBLE Relay action beg ins upo n any tro uble co ndition in an assigned zone in the zone list. • NOT USED Relay act ion is not dependent upon one of the a bove events. 2. ZONE LIST (ZL) is a group of zones to whi ch the “ EVENT ” applies in o rder to activate a particular re lay. No te ...

  • Vista Ademco N7227V5 - page 71

    Section 16 - Output Device Programming 16 – 3 If a relay is energized before a 4-wire smok e detector is r eset, the relay will be stopped by the interr uption of Aux. Power that resets the smoke detec tor. If this is not desired, the power to the relay unit should be supplied from another 12V power sourc e (e.g., the same sour ce that is powerin ...

  • Vista Ademco N7227V5 - page 72

    VISTA -10SE Installat ion and Setup Guide 16 – 4 02 Start: Zn List No List 0 If a zone list will be used to START the relay action, en ter the zo ne list number (to be programmed in field ✱ 81): 1, 2, or 3. If no t used, en ter 0. Press the [ ✱ ] key to continue. 02 Start: Zn Typ Not Used 00 If a zone type o r system oper ation will be used t ...

  • Vista Ademco N7227V5 - page 73

    17 – 1 SECTION 17 Zone Lists ( ✱ 81 Menu Mode) •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About Zone L ist Menu Mode ♦ Zone Li st Dis play s ••••••••••••••••••••••••• ...

  • Vista Ademco N7227V5 - page 74

    VISTA -10SE Installat ion and Setup Guide 17 – 2 Notes: • Any lis t may include a ny or all of the s ystem's zone numbers. • A zone lis t can be as signed to more t han one output rel ay. • If you only want to review what has been programmed previously , press #81. The rev iew can be advance d by using the ✱ key. When fini shed, pres ...

  • Vista Ademco N7227V5 - page 75

    18 – 1 SECTION 18 Alpha Descriptor Programming ( ✱ 82 Menu Mode) •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About Alpha Descriptor P rogramming ♦ Zone Descriptors ♦ Programming Zone Descriptors ♦ Adding Custom Wo ...

  • Vista Ademco N7227V5 - page 76

    VISTA -10SE Installat ion and Setup Guide 18-2 Program Alpha ? 0 = No, 1 = Yes 0 2. Enter ✱ 82. The “ Prog ram Alp ha ? ” prompt appears. If you press 0 (No), proceed to step 4 . Custom Words ? 0 = No, 1 = Yes 0 3. By pressing 1 (Yes) in step 2 above: The “ Cu stom Wo rds ? ” prompt appears. Proceed to t he six steps fo r Add ing C ustom ...

  • Vista Ademco N7227V5 - page 77

    Section 18 – Alpha Descriptor Programming 18-3 ✱ ZN 01 BACK DOOR A ↑ Flashing Cursor if “ 6 ” is pressed (system is ready for n ext word). 9. Press [6] to accept the selected word . NOTE: If thes e are the only words you are usi ng for the descriptor, press [8] inst ead of [6] to s ave them in memory. 10. The two words in our example have ...

  • Vista Ademco N7227V5 - page 78

    VISTA -10SE Installat ion and Setup Guide 18-4 5. Repeat st eps 3 an d 4 to create t he desired word(s). Note that the [4] key can b e used to move the curs or to the left . Use the [6 ] key to make a space be tween characters. Reme mber, no word or word- string can exceed 10 characters includ ing spaces. 6. Press the [ 8] ke y to sav e th e c u st ...

  • Vista Ademco N7227V5 - page 79

    Section 18 – Alpha Descriptor Programming 18-5 ALPHA VOCABULARY LIST (For Entering Zone Desc riptors) NOTE: Some rar e ly use d words appearing in previously publishe d lists have be en delete d fro m the list belo w. Use o nly this list for selecting zone descriptors. 000 (Word Space) A • 001 AIR • 002 ALARM 004 ALLEY 005 AMBUS H • 006 ARE ...

  • Vista Ademco N7227V5 - page 80

    VISTA -10SE Installat ion and Setup Guide 18-6 ...

  • Vista Ademco N7227V5 - page 81

    19 – 1 SECTION 19 Remote Programming and Control (Downloading) •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ About Remot e Programming ♦ Equipment Required •••••••••••••••••••••? ...

  • Vista Ademco N7227V5 - page 82

    VISTA -10SE Installat ion and Setup Guide 19-2 Equipment Required At the premises: VISTA – 10SE and keyp ad. At the inst aller's office/hom e: An IBM PC -compa tible comput er. Either a SMARTMODEM 1200 (Leve l 1.2 or highe r exte rnal or Lev el 1.1 or h igher [with 4 pos ition DIP switch] i n t ernal st yle), or an Optima 24 Plus FAX96 Modem ...

  • Vista Ademco N7227V5 - page 83

    20 – 1 SECTION 20 System Communication ••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Panel Communication with Central S tation ♦ Report Code Formats ♦ System Communication Programming ••••••••••••? ...

  • Vista Ademco N7227V5 - page 84

    VISTA -10SE Installat ion and Setup Guide 20-2 The following describes each fo rmat in greater detail. 3+1 and 4+1 S tandard Formats Comprise a 3- (o r 4-) digit su bscriber numbe r and a single -digit report code (e.g., A larm, T rouble, Res tore, Open, Cl ose, etc. ). 3+1 and 4+1 Exp anded Format s Comprise a 3- (or 4-) digit subscribe r number, ...

  • Vista Ademco N7227V5 - page 85

    21 – 1 SECTION 21 System Operation •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Security Codes ♦ Keypad Functions ♦ 4285/4286 VIP Modul e ♦ Exit Error Alarm Displays ♦ Trouble Conditions ••••••••• ...

  • Vista Ademco N7227V5 - page 86

    VISTA -10SE Installat ion and Setup Guide 21-2 Duress Code This feature is intended for use when you are forced to dis arm or arm the s ystem under threat. Whe n used, th e syste m will act no rmally, but can silently no tify the central station of your situa tion, if t hat s ervice has b een provided. Important: Thi s code is us eful only when the ...

  • Vista Ademco N7227V5 - page 87

    Section 21 – System Operation 21-3 Arming INSTANT .............. Enter cod e + INSTANT [7] . Arming MAXIMUM ............ Enter co de + MAXIMUM [ 4]. Quick Arming ..................... Simply press [#] ke y in place o f code, the n press (if enabled) AWAY , STAY, INSTANT, or MAXIMUM to arm system as desired. Note tha t the [#] k ey cannot be used ...

  • Vista Ademco N7227V5 - page 88

    VISTA -10SE Installat ion and Setup Guide 21-4 4285/4286 VIP Module (if used) Refer to the s eparate inst ructions s upplied with t he VIP Module for informa tion concerning its opera ting procedures. Relay Outpu ts (if used) If relay output s are us ed, two keypad ent ries a vailab le to the us er are included among the syst em operation choices ( ...

  • Vista Ademco N7227V5 - page 89

    Section 21 – System Operation 21-5 • A display of BAT (on fixed-word keypa ds) or SYSTEM LO BAT (on alp ha key pads) with no zone numbe r indicates th at the syste m's main standby battery is w eak. • A display of "BAT" (on fixed-word keypads) or “ LO BAT ” (on alp ha key pads) w ith a zone number and a once per minut e &qu ...

  • Vista Ademco N7227V5 - page 90

    VISTA -10SE Installat ion and Setup Guide 21-6 ...

  • Vista Ademco N7227V5 - page 91

    22-1 SECTION 22 Testing the System •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Test Procedures ♦ Transmitter Sniffer Mode ♦ Go/No Go Test ••••••••••••••••••••••••••• ...

  • Vista Ademco N7227V5 - page 92

    VISTA -10SE Installat ion and Setup Guide 22-2 If a key (or key pai r) has been progra mmed for fire, the keypa d and external s ounder will emit an inte rrupted alarm so und, and ALARM, FIRE and zone number will be displa yed. Silence alarms by entering the s ecurity code and pressing [OFF ] key. 9. If Outpu t Relay Units h ave bee n installed , t ...

  • Vista Ademco N7227V5 - page 93

    23 – 1 SECTION 23 Specifications & Accessories •••••••••••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Specifications ♦ Accessories •••••••••••••••••••••••••••••••? ...

  • Vista Ademco N7227V5 - page 94

    VISTA -10SE Installat ion and Setup Guide 23-2 Accessories (Compatible Devices) No. 1321 16.5VAC, 25VA Plug-In Transformer (in USA) No. 1321CN 16.5VAC, 25VA Plug-In Transformer (in Canada) Sounders ADEMCO AB-12M 10 ” Motoriz ed Be ll & Box Motor bell & box . UL Grade A. 100mA cu rrent draw. ADEMCO 1011BE12M 10 ” Motoriz ed Be ll & B ...

  • Vista Ademco N7227V5 - page 95

    A-1 APPENDIX A Regulatory Agency Statements •••••••••••••••••••••••••••••••••••••••••••••••••• FEDERAL COMMUNICATIONS COMMISSION (FC C) PART 15 STATEMENT Thi s equi pment h as b een tested to FC C requ iremen ts and h as b een foun d acceptabl e for ...

  • Vista Ademco N7227V5 - page 96

    VISTA -10SE Installat ion and Setup Guide A-2 UL NOTICES 1. This is a "Grade A" reside ntial system . 2. The 4285/4286 VIP Module an d 7720PLUS or 7820 Lo ng-R ange Rad ios have not bee n UL tested a nd cannot, t herefore, be used i n a UL ins talla tion. 3. The Entry Delay (field ✱ 38) cannot be gre ater than 45 se conds f or UL instal ...

  • Vista Ademco N7227V5 - page 97

    B-1 APPENDIX B Limitations and Warranties •••••••••••••••••••••••••••••••••••••••••••••••••• WARNIN G THE LIMITATIONS OF THIS ALARM SYS TEM While thi s Syst em is an a dvan ced desi gn securit y system, i t does not offer guara nteed protect ion agai ...

  • Vista Ademco N7227V5 - page 98

    VISTA -10SE Installat ion and Setup Guide B-2 ADEMCO LI M I TED WARRANTY Alarm Device Manufacturing Company, a Division of Pittway Corporation, and it s divisions , subsidiaries and affiliat es ( “ Seller ” ), 165 Eileen W ay, Syoss et, New York 11791, w arrant s its product s to be in conf ormanc e with its own plans and s pecifi cations and t ...

  • Vista Ademco N7227V5 - page 99

    TO DETERMINE TO T AL ST ANDBY LOAD ON BA TTER Y , ADD 100mA TO TO T AL OF AUX. POWER OUTPUT AND REMOTE KEYP AD CURRENTS. USE UL LISTED LIMITED ENERGY CABLE FOR CONNECTIONS CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQU ARTERS OR A CENTRAL ST A TION SHALL BE PERMITTED ONL Y WITH THE PERMISSION OF THE LOCAL A UTHORITY HA VING JURISDICTION ...

  • Vista Ademco N7227V5 - page 100

    ¬19Wl N7227V5 10/00 165 Eileen Way, Syosset, New Yo rk 11791 Copyright © 2000 P I TTWAY CORPORA TION ...

Manufacturer Vista Category Home Security System

Documents that we receive from a manufacturer of a Vista Ademco N7227V5 can be divided into several groups. They are, among others:
- Vista technical drawings
- Ademco N7227V5 manuals
- Vista product data sheets
- information booklets
- or energy labels Vista Ademco N7227V5
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vista Ademco N7227V5.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vista Ademco N7227V5, service manual, brief instructions and user manuals Vista Ademco N7227V5. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vista Ademco N7227V5.

Similar manuals

A complete manual for the device Vista Ademco N7227V5, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vista Ademco N7227V5 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vista Ademco N7227V5.

A complete Vista manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vista Ademco N7227V5 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vista Ademco N7227V5, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vista Ademco N7227V5, that we can find in the current document
3. Tips how to use the basic functions of the device Vista Ademco N7227V5 - which should help us in our first steps of using Vista Ademco N7227V5
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vista Ademco N7227V5
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vista Ademco N7227V5 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vista Ademco N7227V5?

Use the form below

If you did not solve your problem by using a manual Vista Ademco N7227V5, ask a question using the form below. If a user had a similar problem with Vista Ademco N7227V5 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)