-
Tanaka TED-210 - page 1
Owner’ Owner’ Owner’ Owner’ Owner’ s Man s Man s Man s Man s Man ual ual ual ual ual Model Numbers: TED-210, TED-262DH TED-210, TED-262DH TED-210, TED-262DH TED-210, TED-262DH TED-210, TED-262DH TED-262L/R/HS TED-262L/R/HS TED-262L/R/HS TED-262L/R/HS TED-262L/R/HS DRILL DRILL DRILL DRILL DRILL S S S S S P/N 24929 Date 01-24-04 Supplier T ...
-
Tanaka TED-210 - page 2
www.tanaka-usa.com 1 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Before using this unit: • Read the operator’s manual carefully. • Check that the cutt ing equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment. See “Maintenance”. WARNING Read, understand and follow ...
-
Tanaka TED-210 - page 3
www.tanaka-usa.com 2 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS 1. What is What? Since this manual coves several models, there ma y b e some difference between pictures and your unit. Use the instructions that apply to your unit. 1. Handle 2. Plug cap 3. Ignition Switch 4. Muffler 5. Chuck unit 6. Throttle trigger 7. Rec ...
-
Tanaka TED-210 - page 4
www.tanaka-usa.com 3 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS 2. Warnings and safety instruc tions Operator safety • Always wear a safety fac e shield or goggles. • Always wear heavy, long pants, boots and gloves. Do not wear loose clothing, jewelry, s h ort pants, sandals or go barefoot. Secure hair so it is above ...
-
Tanaka TED-210 - page 5
www.tanaka-usa.com 4 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Assembly procedures Assembling (Fig. 1-1, 1B, 1C) 1. Assemble the handle (1), which is su pplied with the unit to the gear case. 2. Screw the chuck unit (2) into the drive shaft (clockwise) after the collar B (3) has been installed. NOTE! The collar B(3) is ...
-
Tanaka TED-210 - page 6
www.tanaka-usa.com 5 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Starting 1. Set ignition switch (1) to (RUN) position. (Fi g. 2-2, 2B) *Push priming bulb (4) several ti mes so that fuel flows through the bulb or return pipe ( 5). (If so equipped) (Fi g. 2-2C) 2. Set choke lever to (CHOKE D) position. (Fig. 2-3, 3B) 3. Pu ...
-
Tanaka TED-210 - page 7
www.tanaka-usa.com 6 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Drilling (Fig. 2-5,5B) • Always hold unit firmly with both ha nds on handles and body well bal anced. • Operate at a high engine speed and let the drill bi t do the work. Do not force bit into the hole. • If materials become twisted around drill bit, s ...
-
Tanaka TED-210 - page 8
www.tanaka-usa.com 7 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS • To tighten the chuck more securely, set a 19mm spanner (1) between gear case and drill chuck to lock drive shaft. Turn on lock lever (2 ) first, then hit the m ounted chuck handle with a hammer to screw in (clockwise) the chuck. (T ED-262L~262DH) (Fig. 2 ...
-
Tanaka TED-210 - page 9
www.tanaka-usa.com 8 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Maintenance MAINTENANCE, REPLA CEMENT, OR REPAIR OF THE EMISSION CONTROL D EVICES AND SYSTEMS MA Y BE PERFORMED BY ANY NON ROAD ENGINE RE PAIR ESTABLISH MENT OR INDIVIDUAL . Carburetor adjustment (Fig. 3-1, 1 B) WARNING! The bit may be spinning during carbur ...
-
Tanaka TED-210 - page 10
www.tanaka-usa.com 9 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Air filter (Fig. 3-2, 2B) The air filter must be cleaned f rom dust and dirt in order to avoid: • Carburetor malfunctions. • Starting problems. • Engine power reduction. • Unnecessary wear on the engine parts. • Abnormal fuel consumption. Clean the ...
-
Tanaka TED-210 - page 11
www.tanaka-usa.com 10 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Cleaning the cylinder fins (Fig. 3-6) When wood chips are caught between cylinder fins (1 ), the engine may overheat, resulting in lower output. To avoid this, always keep cylinder fins and fan case clean. Every 1 00 Operat ing hours, or once a year (more o ...
-
Tanaka TED-210 - page 12
www.tanaka-usa.com 11 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Maintenance schedule Below you will find some general main tenance instructions. For further in formation, please contact your servicing dealer. Daily maintenance • Clean the exterior of th e unit. • Check that the drilling attachment is properly center ...
-
Tanaka TED-210 - page 13
www.tanaka-usa.com 12 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Specifications NOTE! Equivalent noise level/vibration level are calculated as the time-weighted en ergy t otal for noise/vibration levels under various working conditions with the followin g time distribution : ½ idle, ½ full speed. All data subject to ch ...
-
Tanaka TED-210 - page 14
www.tanaka-usa.com 13 contacttanaka@tanaka-ism.com Owner’s Manual TED-210/TED-262L/R/DH/HS Declaration of conformity Déclaration de conformité Dichiarazione di conform itá Konformitätser klärung Declaración de confor midad Konformitetsd eklaration We, Tanaka Kogyo Co., Ltd., 3-4- 29 Tsudanuma, Narashino, Chiba, Jap an Nous,soussignés, Noi, ...
Do you have a question concerning Tanaka TED-210?
Use the form below
If you did not solve your problem by using a manual Tanaka TED-210, ask a question using the form below. If a user had a similar problem with Tanaka TED-210 it is likely that he will want to share the way to solve it.