English dropdown-ico

Manual Cub Cadet 526 WE

24 pages 1.76 mb
Download

Go to site of 24

Summary
  • Cub Cadet 526 WE - page 1

    CUB CADET LLC, P .O. BO X 36 1 1 3 1 CLEVEL AND, OHIO 44 1 36 - 00 1 9 Print ed In USA O p e r a t O r ’ s M a n u a l Safe Ope ration Practices • Set- Up • Operation • M aintenance • Ser vice • T rou bleshooting • Warranty W ARNING READ AND FOL LOW A LL SA FET Y RULES A ND I NSTR UC TIONS IN THIS MANU AL BEFORE A T TEMPTING TO OPERA ...

  • Cub Cadet 526 WE - page 2

    T o The Owne r 1 2 Record Product Infor mation Befo re set ting up and o perating yo ur new equip ment, pl ease loc ate the model p late on the equ ipment and re cord the infor mation in the pr ovided are a to the right. Y ou c an locate th e mode l plate by sta nding at the op erator ’ s p osition and l ooki ng at the lower, rear sec tion of the ...

  • Cub Cadet 526 WE - page 3

    Im por tant Safe Op erat ion Pr ac tic es 2 3 T raining Read, u nders tand, an d follow all ins truc tions on the machine an d in the manual(s) before at tempting to assemb le and op erate. Keep this manu al in a safe p lace for futur e and regula r referen ce and for orde ring rep lacement par ts . Be fam iliar with all contro ls and their p roper ...

  • Cub Cadet 526 WE - page 4

    4 s ecti On 2 — i MpOr t ant s afe O per a tiOn p r actices Safe Handling of Gasoline T o avoid per sonal injur y or p roper t y damage us e ex treme ca re in handli ng gasolin e. Gasolin e is ex tremel y flam mable and th e vapo rs are ex plosive. Se rious pe rsona l injur y can occur wh en gasol ine is spille d on yours elf or you r clothes whi ...

  • Cub Cadet 526 WE - page 5

    5 s ecti On 2 — i MpOr t ant s afe O per a tiOn p r actices Maintenance & S torage Never tam per with s afet y devices . Check their p roper ope ration re gularly. Refer to the mainten ance and adjust ment sec tions of this m anual. Befo re cleaning , repairin g, or inspe ctin g machine diseng age all control l evers and s top the engin e. W ...

  • Cub Cadet 526 WE - page 6

    Assembly Handle Place the shif t lever in t he For ward- 6 p osition Obse rve the l ower rear area of th e snow thrower to be sur e both ca bles are ali gned with r oller gui des befo re pivoting the handl e upward. S ee Fig. 3- 1. NOTE: M ake cert ain the upp er ends of each c able are seated p roperl y in its br acket. Secu re the handle by ti gh ...

  • Cub Cadet 526 WE - page 7

    Finish sec uring chute contro l assembly to chute sup por t bracket w ith wing nut an d hex screw re moved earlie r . See S ee Fig. 3- 4. Check that al l cables ar e prope rly routed th rough the c able guide o n top of the engi ne. See Fig. 3 -5. 3. 4. Figur e 3- 4 Set -Up Shear Pins A pair of re placeme nt auger shear p ins and bow tie cot ter pi ...

  • Cub Cadet 526 WE - page 8

    Tire Pressure Befo re oper ating, check t ire pressure an d reduce pressu re in both tire s to bet ween 1 5 psi and 20 psi. NOTE: I f the tire pressu re is not equal i n both tires, th e machine may not travel in a st raight path and th e shave plate may wear unevenl y . Gas & Oil Fill-Up W AR NIN G! Use ex treme c are when ha ndling gasol ine. ...

  • Cub Cadet 526 WE - page 9

    Auger C ontrol W AR NIN G! Prior to op erating you r snow thrower , caref ully read a nd follow all i nstruc tions b elow. Per form all adj ustment s to verif y your snow throwe r is ope rating saf ely and pro perl y . Check the a djustment o f the auger contro l as follows: When th e auger contro l is release d and in the dise ngaged “up” posi ...

  • Cub Cadet 526 WE - page 10

    Snow thrower contro ls and feature s are describ ed be low and illust rated in Fig. 4 - 1 . NOTE: Fo r detaile d inform ation on all en gine controls , refer to the sep arate T ecumse h Engine Op erator ’ s Manua l. Shif t Le ver The shi f t lever is locate d in the right sid e of the handl e panel and is us ed to determ ine ground spe ed and dir ...

  • Cub Cadet 526 WE - page 11

    Throttle Control The thr ottle contr ol is locate d on the rear of th e engin e. It regulates th e spee d of the engin e and will shut o ff th e engine wh en moved into the STOP pos ition. Primer Pressing the p rimer fo rces fuel dire ctl y into the engi ne’ s c arbureto r to aid in cold- weather sta rtin g. Oil Fill Engine oi l level can be ch e ...

  • Cub Cadet 526 WE - page 12

    Chute Direc tional Con tr ol The chute di rec tional contro l is located o n the lef t side o f the dash pan el. T o change the d irec tion in which s now is thrown, squ eeze the but ton on the j oy-sti ck and pivot the joy -stick to the right or to th e lef t. T o change the a ngle/distance whi ch snow is thrown, pi vot the joy- stick for war d or ...

  • Cub Cadet 526 WE - page 13

    Starting The Engine Atta ch spark plu g wire to spark p lug. Make cer tain th e meta l loop on th e end of the sp ark plug wi re (inside the rubb er boot) is f astened s ecurel y over the metal ti p on the spark p lug. Make cer tain b oth the auger contro l and drive contro l are in the dise ngaged (rele ased) posi tion. Move throt tle control up t ...

  • Cub Cadet 526 WE - page 14

    T o Engage Driv e With the th rottl e control in the Fast (rabbit) positi on, move shif t lever into on e of the six fo rwar d (F) positio ns or two revers e (R) positions. S elec t a spe ed appr opriate for th e snow conditi ons and a pace you ’ re comf ort able wi th. Sque eze the dri ve control against t he handle the s now thrower wil l move. ...

  • Cub Cadet 526 WE - page 15

    Maintenance Engine Refe r to the T ecumseh Eng ine manual pa cked with your machine fo r all engin e maintenance. Sha ve Plate an d Skid Shoes The shave plate an d skid sh oes on the b ottom o f the snow thrower are su bjec t to wear . They s hould be ch ecked pe riodic ally and rep laced when n ecessar y. T o remove sk id shoes: Remove the fo ur c ...

  • Cub Cadet 526 WE - page 16

    Auger Sh af t At least on ce a season, rem ove the shear pins f rom the auge r shaf t. Sp ray lubrica nt inside the shaf t and a round the sp acers and the f lang e bearings f ound at eithe r end of the sha ft . See Fig . 6-3. Adjustments Shif t Cable If the f ull range o f speed s ( f orw ard and rever se ) c annot be achieved , refer to the f igu ...

  • Cub Cadet 526 WE - page 17

    Drive Control When th e drive control is re leased an d in the disen gaged “up” positi on, the cab le shoul d have v e ry li ttle s lack. It s hould NOT be tight. NOTE: I f excessive slack is pr esent in the dri ve cable or i f the snow thrower ’ s d rive is disenga ging intermit tently dur ing ope ration, the c able may be in n eed of a djus ...

  • Cub Cadet 526 WE - page 18

    Belt Replacement Auger Belt T o remove and re place your snow throwe r’s auger be lt, proce ed as foll ows: T o prevent spil lage, place a pi ece of plast ic wrap und er the gas cap an d tighten secu rely . Remove the p lastic b elt cover on the fro nt of the engin e by removin g the two s elf-ta pping scr ews. See Fig . 7 - 1 . Roll th e auger b ...

  • Cub Cadet 526 WE - page 19

    Remove the b elt fro m around the au ger pull ey , and slip th e bel t bet ween the sup por t bracket a nd the auger p ulley . See Fig . 7 -5. Reassem ble auge r belt by fo llowing ins truc tions in revers e orde r . NOTE: D o not forge t to reinsta ll the shoul der screw and re connec t the sprin g to the frame a fter i nstallin g a repla cement a ...

  • Cub Cadet 526 WE - page 20

    Slip the dr ive belt of f the p ulley and b etwe en fric tion whee l and fri ctio n wheel dis c. Se e Fig. 7 - 7 . Remove and re place be lt in the revers e order. NOTE: En gaging the dr ive control will eas e reassembl y of the be lt. 6. 7. F ric tion Wheel Removal If the sn ow thrower fails to dr ive with the drive contr ol engage d, and pe rf or ...

  • Cub Cadet 526 WE - page 21

    Caref ully remove the h ex nut which s ecures the h ex shaf t to the snow thrower f rame and l ightly tap the s haf t ’ s end to dislod ge the ball b earing f rom the right si de of the fram e. See Fig. 7-9. NOTE: B e caref ul not to damage the t hreads on the sh aft . Caref ully posi tion the he x shaf t downward and to th e lef t bef ore caref ...

  • Cub Cadet 526 WE - page 22

    T ro ublesh ooti ng 7 22 Pr oblem Cause Remedy Engi ne fails to start Chok e not in ON position. Spark plug wir e disc onnec ted. F uel tank empt y or stale fuel. Engi ne not primed. F aulty spark plug. Blocked fuel line . Safety ke y not in ignit ion on en gine. 1. 2. 3. 4. 5. 6. 7. Mov e choke to ON position. Conn e ct wi re to spark plug. Fil l ...

  • Cub Cadet 526 WE - page 23

    C omponent Pa r t Number a nd Descrip tion 9 29 - 007 1 Ex tention Cord, 1 1 0V 954- 0 4050 Auger Drive Belt 7 54 - 036 7 Wheel D rive Belt 68 4- 0 4 1 53 Friction Whee l Assembly 93 5- 0 4054 F r iction Whe el Rubber 9 25 - 042 1 3 Lamp, 1 2. 5V , 3 7 . 5W 738- 04 1 2 4A Shear Pin, 1 .50 7 1 4 - 04 040 Bow- tie C ot ter Pin 790 - 00 1 4 1 Stainles ...

  • Cub Cadet 526 WE - page 24

    Th e limi te d war ra nt y s et f or th b elo w is gi ven by Cu b Cad et L LC wi th re spe ct t o new m erc han dise p urc has ed a nd us ed in th e Uni ted S t at es, it s po ss ess ions a nd te rr ito rie s, an d by M TD Pr odu ct s Li mit ed wi th re spe ct t o new m erc han dise p urc has ed a nd us ed in C ana da an d / or it s ter ri tor ie s ...

Manufacturer Cub Cadet Category Snow Blower

Documents that we receive from a manufacturer of a Cub Cadet 526 WE can be divided into several groups. They are, among others:
- Cub Cadet technical drawings
- 526 WE manuals
- Cub Cadet product data sheets
- information booklets
- or energy labels Cub Cadet 526 WE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cub Cadet 526 WE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cub Cadet 526 WE, service manual, brief instructions and user manuals Cub Cadet 526 WE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cub Cadet 526 WE.

Similar manuals

A complete manual for the device Cub Cadet 526 WE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cub Cadet 526 WE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cub Cadet 526 WE.

A complete Cub Cadet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cub Cadet 526 WE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cub Cadet 526 WE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cub Cadet 526 WE, that we can find in the current document
3. Tips how to use the basic functions of the device Cub Cadet 526 WE - which should help us in our first steps of using Cub Cadet 526 WE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cub Cadet 526 WE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cub Cadet 526 WE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cub Cadet 526 WE?

Use the form below

If you did not solve your problem by using a manual Cub Cadet 526 WE, ask a question using the form below. If a user had a similar problem with Cub Cadet 526 WE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)