Manual Zenoah HEZ2500F

36 pages 1.26 mb
Download

Go to site of 36

Summary
  • Zenoah HEZ2500F - page 1

    OWNER / OPERA T OR MANUAL STICK EDGERS 848-A41-93A1 (501) HE225F HEZ2500F The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our product, please read this manual carefully to understand the proper use of your unit. W ARNING (HE225F ...

  • Zenoah HEZ2500F - page 2

    ...

  • Zenoah HEZ2500F - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • Zenoah HEZ2500F - page 4

    2. Specifications ■ HE225F/HEZ2500F Overall size(LxWxH) ································ 68.1(1730)x12.3(313)x12.3(312) / 69.8(1773)x12.6(320)x12.3(312) in(mm) Dry weight w/o acc. ···································································· ...

  • Zenoah HEZ2500F - page 5

     5  3. W arning labels on the machine (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning/Attention (4) Keep all children, bystanders and helpers 15 meters away from the machine. If warning label peel off or become soiled and impossible to read, you should contact the dealer from whic ...

  • Zenoah HEZ2500F - page 6

     6  For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: AIR CLEANER COVER (c) The direction to open the choke Position: ...

  • Zenoah HEZ2500F - page 7

    5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. ...

  • Zenoah HEZ2500F - page 8

     8  b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the produ ...

  • Zenoah HEZ2500F - page 9

    ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more persons, ca ...

  • Zenoah HEZ2500F - page 10

     10  the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Red Max servicing dealer for repair. ■ USING THE PRODUCT Cut only materials recommended by the manufacturer. And use only for tasks explained in ...

  • Zenoah HEZ2500F - page 11

    ■ MAINTENANCE 1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals. 2. Always be sure to turn off the engine before performing any maintenance or checking procedures. The metallic parts reach high temperatures immediately after stopping the engin ...

  • Zenoah HEZ2500F - page 12

     12  5. For safe operation ■ HANDLING FUEL 1. The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire whi ...

  • Zenoah HEZ2500F - page 13

    SE4 ■ MOUNTING ENGINE (SE1) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult ...

  • Zenoah HEZ2500F - page 14

     14  7. Fuel ■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 • Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion. • These engines are certified to operate on ...

  • Zenoah HEZ2500F - page 15

    7. Fuel  15  again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication on t ...

  • Zenoah HEZ2500F - page 16

     16  8. Operation OP2 (1) (2) (3) OP1 (1) (2) (3) OP3 (4) (7) (5) (6) OP4 The RedMax stick edgers are designed for edging lawn in gardens, parks, roadsides and so on. Before starting the engine, take the operating position and adjust the handle position and the wheel height as necessary. ■ ADJUSTING WHEEL HEIGHT 1. Loosen the wing nut and c ...

  • Zenoah HEZ2500F - page 17

    8. Operation  17  • Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 6. Move the choke lever downward to open the choke. And restart engine. (OP3) 7. Allow the engine to warm up for a several minutes before starting operation. 1. When restarting the engine immediately after st ...

  • Zenoah HEZ2500F - page 18

     18  8. Operation ■ HOW TO USE 1 Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2 Keep the blade guard and the mad guard attached in place at all times when the unit is operated. 3 Before starting a job, ...

  • Zenoah HEZ2500F - page 19

    •A lways be sure to stop the engine before inspecting the stick edger for problems or performing maintenance. • Never alter the stick edger or take the engine apart. •W hen replacing parts, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax stick edger. WARNING 9. Maintenance  ...

  • Zenoah HEZ2500F - page 20

     20  •M ake sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry co ...

  • Zenoah HEZ2500F - page 21

    ■ MUFFLER • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire. ■ SPARK ARRESTER • The muffler is equipped with a spark arrester to prevent re ...

  • Zenoah HEZ2500F - page 22

     22  9. Maintenance ■ BLADE (MA7) • Place the blade between holders (A) and (B) while locking the gear shaft by putting the bar, through the key holes on the holder(A) and the gearcase. Use the socket and the screwdriver to tighten the blade mounting bolt. (1) Blade mounting nut (Left-handed) Tightning Torque: 130~150in-lbs(15~20N.m.) (2) ...

  • Zenoah HEZ2500F - page 23

    10. Storage • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.  23  9. Maintenance • If waste gets stuck and causes blockage a ...

  • Zenoah HEZ2500F - page 24

     24  11 . T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug is fouled/wet ➞ clean/dry ? ...

  • Zenoah HEZ2500F - page 25

    12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and th ...

  • Zenoah HEZ2500F - page 26

    12. Parts list  26  Fig.1 DRIVE UNIT (S/N 200001 and up) ...

  • Zenoah HEZ2500F - page 27

    Fig.1 DRIVE UNIT (S/N 200001 and up) Key# Description Part Number Q'ty 1P IPE COMP. T3207-12100 1 2 SHAFT COMP. T3207-12200 1 3 GEARCASE ASSY T3207-13000 1 4• GEARCASE T3207-13110 1 5• HOLDER-B 6129-13250 1 6• HOLDER-A 6129-13240 1 7• SHAFT 6129-13211 1 8• PINION T3207-13310 1 9• GEAR 6129-13220 1 10 • BEARING 06004-06201 1 11 ? ...

  • Zenoah HEZ2500F - page 28

    12. Parts list  28  Fig.2 ENGINE UNIT HE225F (S/N 50100000 and up) ...

  • Zenoah HEZ2500F - page 29

    Fig.2 ENGINE UNIT HE225F (S/N 50100000 and up) Key# Description Part Number Q'ty 1 CYLINDER 5580-12110 1 2 GASKET, base 5500-12213 1 3 BOLT 1850-12130 2 4 PLUG RCJ-6Y 3699-90419-10 1 5 CRANKCASE COMP. 5500-21100 1 6• PIN 2629-21130 3 7 GASKET 5500-21141 1 8 BEARING 06030-06001 2 9 SEAL 2169-21210 1 10 SEAL 1850-21220 1 11 SNAP RING 04065-028 ...

  • Zenoah HEZ2500F - page 30

    Fig.3 ENGINE UNIT HEZ2500F (S/N 50100000 and up)  30  12. Parts list ...

  • Zenoah HEZ2500F - page 31

    Fig.3 ENGINE UNIT HEZ2500F (S/N 50100000 and up)  31  Key# Description Part Number Q'ty 1 CYLINDER 848-F30-12A2 1 2 GASKET, base 4810-12210 1 3 BOLT 1850-12130 2 4 INSULATOR 4810-13162 1 5 GASKET, insulator 4810-13120 1 6G ASKET, carburetor 4810-13130 1 7 SCREW 0263-90520 1 8 REEDVALVE (S) ASSY 848-F30-1602 1 10 • REEDVALVE 4810-16120 ...

  • Zenoah HEZ2500F - page 32

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: TH ...

  • Zenoah HEZ2500F - page 33

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

  • Zenoah HEZ2500F - page 34

    ...

  • Zenoah HEZ2500F - page 35

    ...

  • Zenoah HEZ2500F - page 36

    KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 ©P rinted in Japan ...

Manufacturer Zenoah Category Trimmer

Documents that we receive from a manufacturer of a Zenoah HEZ2500F can be divided into several groups. They are, among others:
- Zenoah technical drawings
- HEZ2500F manuals
- Zenoah product data sheets
- information booklets
- or energy labels Zenoah HEZ2500F
All of them are important, but the most important information from the point of view of use of the device are in the user manual Zenoah HEZ2500F.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Zenoah HEZ2500F, service manual, brief instructions and user manuals Zenoah HEZ2500F. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Zenoah HEZ2500F.

A complete manual for the device Zenoah HEZ2500F, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Zenoah HEZ2500F by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Zenoah HEZ2500F.

A complete Zenoah manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Zenoah HEZ2500F - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Zenoah HEZ2500F, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Zenoah HEZ2500F, that we can find in the current document
3. Tips how to use the basic functions of the device Zenoah HEZ2500F - which should help us in our first steps of using Zenoah HEZ2500F
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Zenoah HEZ2500F
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Zenoah HEZ2500F in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Zenoah HEZ2500F?

Use the form below

If you did not solve your problem by using a manual Zenoah HEZ2500F, ask a question using the form below. If a user had a similar problem with Zenoah HEZ2500F it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)