English dropdown-ico

Manual EMC FC4500

110 pages 3.44 mb
Download

Go to site of 110

Summary
  • EMC FC4500 - page 1

    EMC Enterpr ise Storage EMC Corporation 171 South Street, Hopkinton, MA 01748-9103 Cor por ate Headquar ters : (508) 435-1000, (800 ) 4 24-EMC2 Fax : (508) 435-5374 Ser vice : (800 ) SVC-4EMC EMC Fibr e Channel Disk -Array P roc essor Enclos ure (DP E) Rackmo u nt FC4500 HARDWARE REFERE NCE P/N 0140029 01-04 ...

  • EMC FC4500 - page 2

    EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference ii Copyright © EMC Corporation 20 00, 2001. A ll rights rese rved. Printe d Februar y 2001 No part of this pub lication may be repr oduced o r distrib uted in an y form or by any means, or stored in a datab ase or retriev al syst em, with out the pri or wri tten consen t ...

  • EMC FC4500 - page 3

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e iii Regulatory Notices This device c omplies with P art 15 of the FCC rules. Operation is subject to the following tw o conditions: (1) this device may not cause harmful interference, and (2) this device must ac cept any interference received, including interference tha ...

  • EMC FC4500 - page 4

    EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference iv ...

  • EMC FC4500 - page 5

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e v Preface ........................ ........... ........... ................. ........... ................. ............ ................ ....... x i Cha pter 1 About th e Rac kmou nt Disk-Array Processo r Enclosure Introduction ............... ........... .............. ...

  • EMC FC4500 - page 6

    EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference vi Contents Chap ter 3 Ser vicing and Upgr ading a DPE Monitoring DPE Status ..................... ................. ........... ................. .. 3-1 Handling CRUs ...................... ................. ............ ................. ........... .. 3-4 Power Issues ...

  • EMC FC4500 - page 7

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e vii 1-1 DAE ........ ................. ........... ........... ................. ............ ................. ........... ........ 1-2 1-2 DPE Front View ................ ........... ................. ............ ................. ........... ........ 1-5 1-3 DPE Fro ...

  • EMC FC4500 - page 8

    viii EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference Figures 3-6 Closing and Locking the Front Door ...... ................. ........... ................. ..... 3-13 3-7 Removing the SP Fan Pack Cover .... ............ ................. ................. .......... 3-14 3-8 Removing the SP Fan Pack ................ ... ...

  • EMC FC4500 - page 9

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e ix 3-1 Status Lights Color Codes, Front of DPE .............. ........... ................. ........ 3-2 3-2 Status Lights Color Codes, Back of DPE ................... ............ ................ ... 3-3 Ta b l e s ...

  • EMC FC4500 - page 10

    x EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference Ta b l e s ...

  • EMC FC4500 - page 11

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e xi Preface This manual describes how to install the EM C Fibre Channel Disk-Array Pr ocessor Enclosur e (DPE) Rackmount Model FC4 500, and how to replace and add custom er-repl aceable unit s (CRUs). If you will install and service the rack mount DPE, you should read th ...

  • EMC FC4500 - page 12

    xii EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference Preface Conv entions Used in This Manual EMC uses the follow ing conventions for no tes, c aution s, warnings, and danger n otices. A no te pr esent s inf ormat ion th at is im portan t, b ut not hazar d-r elated. CAUTION ! A caution contains infor mation essent ial t ...

  • EMC FC4500 - page 13

    About the Rackmount Disk-Array Processor Enclosure 1-1 1 T o pics in this chapter include: • Intro duction ................. ........... ................. ........... ................. ........... .... 1-2 • DPE Components ................... ................. ........... ................. ........... .... 1-4 • Link Contr ol Cards ( LCCs) .. ...

  • EMC FC4500 - page 14

    1 1-2 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure Intr oduction The DPE is a high ly available, high-p er formance, hi gh-capacity , disk-array storage system that uses a Fibr e Channel Arbi trated Loop (FC-AL) as its interconnect int e rface. Its modula r , sca ...

  • EMC FC4500 - page 15

    1 Introduction 1-3 About the Rackmount Disk-Array Processor E nclosure Y ou can place the DAEs in the same cabinet as the DPE, or in one or more separa te cabinets. The DPE connects to the external Fibre Channel enviro nment using GBIC connectors on the storage processor . High-availa bility features are standar d. The EMC Access Log ix ™ option ...

  • EMC FC4500 - page 16

    1 1-4 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure DPE Co mponents The DPE components include: • A sheet-metal enclos ur e with a midplane, front door , and SP fan pack cover • One or two S Ps • One or two lin k contr ol cards (LCCs) • Up to ten disk modul ...

  • EMC FC4500 - page 17

    1 DPE Com ponents 1-5 About the Rackmount Disk-Array Processor E nclosure identical compo nents, the component in slot A is ca lled component-name A. If th ere is a s ec on d co mp on en t, it is in s l ot B an d i s called comp onen t-name B, as follows. If you have one power supply , it can be in either slot A or s lot B. If you have one SP and o ...

  • EMC FC4500 - page 18

    1 1-6 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure Figure 1-3 DPE Front V iew wit h SP Fan Co ver and Door Remo v ed SP fan pack SP fan pack cover F ront panel with door removed for clarity ...

  • EMC FC4500 - page 19

    1 DPE Com ponents 1-7 About the Rackmount Disk-Array Processor E nclosure Figure 1-4 DPE Back View Figure 1-5 DPE Back V iew wit h Drive Fan P ac k Remo ved Drive fan pac k LCC B with e xpansio n connector (m arked EXP) SP ejector (2 per SP) SP retainin g screw (2 per SP) SP A SP B LCC A with expan sion connec tor (marked EXP ) ac line cord connec ...

  • EMC FC4500 - page 20

    1 1-8 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure SP A work s with LCC A to run SP A ’ s disk modules; SP B works with LCC B to run SP B ’ s disk mod ule s. Front P anel The fr ont panel contains the enclosure ad dress (EA) light, two status lights f or each ...

  • EMC FC4500 - page 21

    1 DPE Com ponents 1-9 About the Rackmount Disk-Array Processor E nclosure Figure 1-6 Front Door The front door has a locki ng latch and an EMI shield. The la tch is a push button w ith a r emovable locking key that you can use in an y DPE or DAE. When the door is open, you can r emove or install disk modules. Storag e Processor s (SPs) The SP is th ...

  • EMC FC4500 - page 22

    1 1-10 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure Figure 1-7 SP Back P anel As shown in the figure , the SP has 4 connectors for DIMMs that comprise both r ead and write caches. Th ese DIMMs come in 12 8-, 256-, or 512-M byte capacity . Memory allo cation is han ...

  • EMC FC4500 - page 23

    1 Link Con tr ol Cards (LC Cs) 1-11 About the Rackmount Disk-Array Processor E nclosure visible from the back of the DPE. For a defin ition of these light colo rs, see the “ Monitoring DPE St atus ” section in Chapt e r 3. If a DPE has on e SP , you can insta ll a second one while the DPE is running.When both S Ps ar e installed, you can r epla ...

  • EMC FC4500 - page 24

    1 1-12 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure Each LCC has two status lights visible from the back of the DPE. For definitions of these light colors, see the “ Moni toring DPE Stat us ” section in Chap ter 3. A latch on the LCC locks it into place to ens ...

  • EMC FC4500 - page 25

    1 Link Con tr ol Cards (LC Cs) 1-13 About the Rackmount Disk-Array Processor E nclosure within the sam e DPE, subject to the restrictions imposed by the Core Softwar e runnin g in the DPE ’ s SPs. Drive Carr ier The disk-drive carrier is a plastic assembly that slides into the enclosure slot guid es and midplane connectors. It has a handle with a ...

  • EMC FC4500 - page 26

    1 1-14 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure Each power supply h a s status li ghts. These status lights are partially visible through the drive fan pack, and fully visible with the drive fan pack r emoved. The status lights are de scribed in the “ Monito ...

  • EMC FC4500 - page 27

    1 Link Con tr ol Cards (LC Cs) 1-15 About the Rackmount Disk-Array Processor E nclosure Figur e 1-12 Drive F an Pack The drive fan pack has one stat us light. The status lig ht is described in the “ Monitoring DPE Stat us ” section of Chapt er 3. Latches on the drive fan pack hold the pa ck in place. Y ou c an r emove the drive fan pack wh ile ...

  • EMC FC4500 - page 28

    1 1-16 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure Figur e 1-13 SP Fa n Pack Latc hes o n the SP fan pa ck ho ld the pack i n plac e. The SP fan pack has one status light visible when the SP fan pack cover is removed. The status light is desc ribed in the “ Mon ...

  • EMC FC4500 - page 29

    1 Red unda nc y in Conf igur ations 1-17 About the Rackmount Disk-Array Processor E nclosure Redundanc y in Conf igurations Mirror ed storage-s ystem write caching requires : • T wo SPs with equal memo ry of at least 128 Mbytes • T w o power supplies • T w o LCCs in the DPE and each DAE • Disks i n slots 0:0 through 0:8 • SPS (standby pow ...

  • EMC FC4500 - page 30

    1 1-18 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence About the Rackmount Dis k-Array Processor Enc losure What Ne xt? Continue to th e next chapter , whi ch explains how to install a DP E. ...

  • EMC FC4500 - page 31

    Installin g a Rackmount DPE 2-1 2 This chapter des cr ibes the DPE installation requirements and proce dures. T opics in this chapter include: • Requirem ents .......................... ........... ................. ............ ................ .... 2-1 • Installing a DPE in a Cabinet................. ................. ........... ............ ...

  • EMC FC4500 - page 32

    2 2-2 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE remaining supply and cord support th e f ull load . Y ou must u se a rackmount cabinet with ac power distribution, and have main branch ac distribution that can handle these values for the num ber of DPEs and DAE s that you will intercon ...

  • EMC FC4500 - page 33

    2 Installing a DP E in a Cabinet 2-3 Installing a Rac kmount DPE Loop Envir onments In an FC-AL en vironment, the DPE is addressed using the FC-AL addres s ID and the e nclosure addr ess (EA). Fibre Channel Arbitrated Loop Address ID (FC- AL Address I D) Each node (such as an SP) on the Fibre Channel fr ont-end loop must have a unique Fibre Channel ...

  • EMC FC4500 - page 34

    2 2-4 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE Y ou install each DPE on two L-shaped mounting rails connected to the cabinet ’ s vertical chann els. • Installin g the cabinet itself is explained in another ma nual. For some standar d cabinets, the information is in a cabinet inst ...

  • EMC FC4500 - page 35

    2 Installing a DP E in a Cabinet 2-5 Installing a Rac kmount DPE 4. Open the DPE front door a s shown below . Figure 2-1 Opening the Fr ont Door C. Lower the door until it is perpendicular to the front of the enclosure. A. If the door is locked: Insert the key in the door’s latch. T urn the key 180 o clockwise. Remove the key from the latch, if d ...

  • EMC FC4500 - page 36

    2 2-6 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE 5. Secure the DPE to the vertical channels of the cabinet a s shown next. Figure 2-2 Securing the DPE to the Cabinet Front Channel 6. Secure the re ar mounts of the DPE to the back channels of the cabinet, as sho wn in Figure 2-3. NOTE: ...

  • EMC FC4500 - page 37

    2 Installing a DP E in a Cabinet 2-7 Installing a Rac kmount DPE Figure 2-3 Securing the DPE to the Cabinet Back Channel 7. Close the DPE fro nt door , as shown in Figure 2-4. The door must b e closed for EMI complia nce. Open the door only to service the DPE. Fast en the brac ket a t the back of each rail to the bottom left and righ t of th e DPE ...

  • EMC FC4500 - page 38

    2 2-8 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE Figure 2-4 Closing and Lock ing the Front Door B. If desired, lock the door as follows: Insert the key in the door ’ s latch. T urn the key 180 o counterclockwise. Remove the key , if desired. A. Raise the door until it latches into pl ...

  • EMC FC4500 - page 39

    2 Installing a DP E in a Cabinet 2-9 Installing a Rac kmount DPE 8. Perform this step on ly if you are installi ng the DPE into an FC-AL environment. Otherwise, continue to the next step. T o c ommunicate in an FC-AL enviro nment, each SP r equires a unique FC-AL ad dress ID (the fr ont-end addr ess). The FC-AL protocol translates the address ID in ...

  • EMC FC4500 - page 40

    2 2-10 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE Figure 2-5 SP Fibre Channel Arbitrated Loop Addr ess ID Switches (Back of SP) FC-AL a dd ress ID (decimal) Left switch setting Right switch setting 000 101 . . . . . . . . . 15 0 F 16 1 0 . . . . . . . . . 31 1 F 32 2 0 . . . . . . . . ...

  • EMC FC4500 - page 41

    2 Installing a DP E in a Cabinet 2-11 Installing a Rac kmount DPE 9. For access to the ac power inlets, you must remove the drive fan pack. Remove the drive fa n pack as shown below . Figure 2-6 Remo ving the Drive Fa n Pac k 10. From the back of the cabinet, plug the ac line cor d into each power supply and turn on the s upply ’ s power , as sho ...

  • EMC FC4500 - page 42

    2 2-12 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE Figure 2-7 Plugging the A C Line Cord into the P ow er Supply and T ur ning on the Po w er Switch Chan nel ac power c ord (right-angl e plug) ac inlet Power swit ch and circuit bre aker Power swit ch and circuit b reaker ac i nlet ac po ...

  • EMC FC4500 - page 43

    2 Installing a DP E in a Cabinet 2-13 Installing a Rac kmount DPE 1 1. Reinstall the drive fan pack on the back of the DPE. Y ou can install the drive fan pack in either horizontal position. However , for a consistent image with DAEs, we r ecommend you install it with th e check light in the upper right corner , as sh own below . Figure 2-8 Install ...

  • EMC FC4500 - page 44

    2 2-14 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE • A void tight bends. If yo u need to make a 90 º bend, do it over 6 to 12 inches. • Do not use optical cables to support weight. That includes long cable runs witho ut support. • Do not pull lo ng runs of cable. It is best to la ...

  • EMC FC4500 - page 45

    2 Installing a DP E in a Cabinet 2-15 Installing a Rac kmount DPE 13. T o expa nd th is DPE , cabl e its L CC EXP conn ector t o the n ext corre sponding DAE ’ s PRI (prim ary) connector , as shown below . Figur e 2-10 Cabling a DPE to a D AE 14. If the DPE ha s another SP , LCC, and DAE, connect the DPE ’ s other LC C and the DA E ’ s other ...

  • EMC FC4500 - page 46

    2 2-16 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE DPE Po w erup and Initialization The only power switches on a DPE ar e those on the power supply , which a r e normally cover ed by the driv e fan pack. As a r esult, a DPE is always a ctive . When ac powe r is initial ly applied to a D ...

  • EMC FC4500 - page 47

    2 DPE P ow erdo wn 2-17 Installing a Rac kmount DPE 4. If the DPE has SPS pr otection, use the power switch on each SPS to turn off power . Wh en yo u t ur n o ff p ow er to a s tor ag e s ys te m w it h an S PS , th e O n Battery light ma y come on for a maximum of 90 seconds during which time th e DPE will contin ue to ru n. This is a normal cond ...

  • EMC FC4500 - page 48

    2 2-18 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Installing a Rackmou n t DPE Binding Disk Modules into Groups After cabling a DPE and an y DAEs, you can bind dis k modules into gr oup s and set up st orage- sys tem cac hing. T o bind disk modul es and set up caching, you wil l use a utility described in the serv ...

  • EMC FC4500 - page 49

    Ser vicing and Upgrading a DPE 3- 1 3 This chapter describes how to mo nitor DPE status, handle CRUs, and replace o r add a CRU. T opics in this chapter include: • Monitoring DPE Status ... ............ ................. ........... ................. ......... 3-1 • Handling CRUs ........... ................. ........... ................. ..... ...

  • EMC FC4500 - page 50

    3 3-2 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE The Check st atus light for the SP fan pa ck is not visible with t he fan pack cover in place. If the DPE s ystem Check light is on with n o other Che ck light on, r emove t he fan pac k cover , as shown on page 3 -14, to ex amine ...

  • EMC FC4500 - page 51

    3 Monitoring DPE Status 3-3 Ser vicing and Upgrading a DPE Disk Active 1 per disk m odule slot Green Off when the mo dule slot is empty or contains a fill er module. Flashing (mostly off) when the drive is powered up but not spinning; this is a nor mal par t of the spin-up sequence, occurr ing during the spin-up del a y of a slot. Flashing (a t a c ...

  • EMC FC4500 - page 52

    3 3-4 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE • If the DPE Check light is on, you shoul d look at the other Check lights to determin e which CRU(s) are faulty . If the Check ligh t for a CRU r emains on, r eplace the CRU as soon as possible. • If a CRU fails in a D PE that ...

  • EMC FC4500 - page 53

    3 Handling CRUs 3-5 Ser vicing and Upgrading a DPE Since you can replace or add any CRU without slid ing the DPE out of the cabinet, you do not have to u se cabinet anti-tip dev ices when you upgrade or service a DPE. If you need to power down a D PE, either: • Shut down the main ac lines to the DPE, or • Remove the drive fan pack (described on ...

  • EMC FC4500 - page 54

    3 3-6 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE A voiding Electr ostatic Discharge (ESD) Damage When you replace or install CR Us, you can inadvertentl y damage the sensitive electronic circuits in the equipm ent by simply touching them. Electrostatic charge that has accumulat e ...

  • EMC FC4500 - page 55

    3 Precautions W hen Removing, Installing, or Stor ing CRUs 3-7 Ser vicing and Upgrading a DPE • Befor e t ouchi ng any CRU, t ouch a bar e (u npain ted) met al su rface of the enclosure. • Befor e removing any CRU fr om its antistatic bag, place one hand firmly on a bar e metal surface of the en closure, and at the same time, pick up the CRU wh ...

  • EMC FC4500 - page 56

    3 3-8 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Precauti ons When Handling Optical Cables When working with optical cables, observe the following precautions: • Keep the covers on all optical cables and o ptical GBICs until you are r eady to insert the cables . The covers pr o ...

  • EMC FC4500 - page 57

    3 Replacing or Adding a Disk M odule 3-9 Ser vicing and Upgrading a DPE Replacing or Adding a Disk Module CAUTION ! When replaci ng or adding a d isk module, o bserve the foll owing: • Remove or install d isk modules only while the st orage system is powered up. • Do not move a disk module that is part of an existin g LUN to another slot i n th ...

  • EMC FC4500 - page 58

    3 3-10 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Y ou must open the DPE ’ s front door to access the disk modules. The door must be closed for EM I compliance w hen the DPE is power ed up. Open it only to repl ace or add a disk module. Remo ving a Dis k or Disk Filler Module 1 ...

  • EMC FC4500 - page 59

    3 Replacing or Adding a Disk M odule 3-11 Ser vicing and Upgrading a DPE 2. Locate the slot wher e you want to install the new or replacement disk module. 3. Remove the disk o r disk filler module from the slot as shown below . Figure 3-3 Remo ving a Disk Filler Module Figure 3-4 Remo ving a Disk Module After r emov ing a disk module, wait for th e ...

  • EMC FC4500 - page 60

    3 3-12 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Continue to the next sectio n to install the new or replacement disk module. Installing a Disk Module 1. Gen tly insert the module as follows: Figure 3-5 Installing a Disk Module The disk module A ctive light flashes to reflect th ...

  • EMC FC4500 - page 61

    3 Replacing or Adding a Disk M odule 3-13 Ser vicing and Upgrading a DPE 3. Close and lock the fro nt door as shown below . Figure 3-6 Closing and Lock ing the Front Door B. If desired, lock the door as follows: Insert the key in the door ’ s latch. T urn the key 180 o counterclockwise. Remove the key , if desired. A. Raise the door until it latc ...

  • EMC FC4500 - page 62

    3 3-14 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Replacing the SP Fan P ac k CAUTION ! Handle a fa n pack gently a nd use an ES D wristband. Do not remove a faulty fan pa ck until you hav e a repla cement avai lable. Y ou can remov e the fan p ack while the DPE is po wered up. I ...

  • EMC FC4500 - page 63

    3 Replacing the SP Fan P ack 3-15 Ser vicing and Upgrading a DPE Figure 3-8 Remo ving the SP F an Pac k Installing the SP F an Pack 1. At the front of the DPE, insert the replacement fan pack into the enclosure, and push gently until the latches engage as shown next. A. Slide the latches on the fan pack inward as shown, and hold them in. B. Grasp t ...

  • EMC FC4500 - page 64

    3 3-16 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figure 3-9 Installing the Replacement SP F an P ack 2. At the fr ont of the deskside DPE, grasp the SP fan pack cover at its sides an d push it onto its bal lstud mounts w ith the louvers slante d down war d as sho wn next. LED ...

  • EMC FC4500 - page 65

    3 Replacing an Op tical GBIC 3-17 Ser vicing and Upgrading a DPE Figur e 3-10 Installing the SP F an Pac k Co v er Replacing an Optical GB IC CAUTION ! Use an ESD wristband. Remo ving an Op tical GBIC Connector Before removi ng any cables, ma ke note of whi ch cables ar e connected to which SP por ts. 1. Remove any optical cables fr om the SP , as ...

  • EMC FC4500 - page 66

    3 3-18 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-11 Remo ving an Optical Cable fr om an SP B A Fibre op tic ca ble Cover Optic al GBIC connec tor Cover A. Unpl ug the f ibre opti c cable from P or t A and/ or P or t B on the SP . B. Install protectiv e cov ers on each ...

  • EMC FC4500 - page 67

    3 Replacing an Op tical GBIC 3-19 Ser vicing and Upgrading a DPE 2. Remove the optical GBIC connector(s) fr om the SP as shown below . Figur e 3-12 Remo ving an Optical GBIC Connector fr om an SP Inst al ling an Optic al GBIC Co nnector 1. Ins ta ll the optica l GBIC connector(s) on the SP as shown next. A B While pres sing in ward on th e retainin ...

  • EMC FC4500 - page 68

    3 3-20 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-13 Installing an Optical GBIC Connector on an SP A B A. Position the op tical GBIC connec tor with the alig nment sl ot toward the bottom . Alignmen t slot Optical GBIC connec tor B. Push the opti cal GBIC connector into ...

  • EMC FC4500 - page 69

    3 Removi ng an SP or a n SP Filler Module 3-21 Ser vicing and Upgrading a DPE 2. Install the appr opriate optical cable(s) on the SP ’ s optical GB IC connector(s) as pr eviously noted and as shown below . Figur e 3-14 Installing an Optical Cable on an SP 3. Remove an d stor e the ESD wristband. Remo ving an SP or an SP Filler Module CAUTION ! Ha ...

  • EMC FC4500 - page 70

    3 3-22 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE board. Before you install a new o r r eplacement SP , you must insta ll a memory module (a new one or one you r emoved fr om a r eturned SP and saved). When r eturning a faulty SP , you must remove the memory modules an d optical ...

  • EMC FC4500 - page 71

    3 Removi ng an SP or a n SP Filler Module 3-23 Ser vicing and Upgrading a DPE Figur e 3-15 Remo ving an SP or Filler Module Retain ing sc rew (one each side) Ejector (one each sid e) A. Loosen th e retain ing scre ws . B. Simulta neously open th e ejectors as f ar as the y will go . C. Gen tly pul l the SP or filler module fro m the enclosur e, s u ...

  • EMC FC4500 - page 72

    3 3-24 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Installing or Replacing an SP Memor y Module SPs, GBICs , and memo ry modules are separate CRU s. New or replacem ent SPs are shipped without memory modules or GBICs. When a memory module and/or GBICs are or der ed with the SP , t ...

  • EMC FC4500 - page 73

    3 Installing or Replacin g an SP Memor y Module 3-25 Ser vicing and Upgrading a DPE Figur e 3-16 Remo ving the Memor y M odule from the SP Aft er r emovi ng the m emor y mod ule, if yo u wa nt to ship the S P , stor e it in its antistat ic bag and special sh ipping package. Then r emove and store the ESD wristband. Installing an SP Memor y Module D ...

  • EMC FC4500 - page 74

    3 3-26 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-17 Installing the Memory Module on the SP 3. If you want to install the SP , contin ue to the next section. Installing an SP or SP Filler Module SPs, GBICs, and memory modu l es are separate CRUs. New or replacement SPs ...

  • EMC FC4500 - page 75

    3 Installing an SP or SP Filler Module 3-27 Ser vicing and Upgrading a DPE Inst al ling a n SP or SP Filler Mod ul e CAUTION ! Handle an SP gently and use an ESD wrist band. 1. Perform this step on ly if you are installi ng the DPE into an FC-AL environment. Otherwise, continue to the next step. If the DPE is operating in a Fibr e Channel Arbitrate ...

  • EMC FC4500 - page 76

    3 3-28 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-18 Setting the SP Address ID 4 3 2 1 0 F E D C B A 9 8 7 6 5 4 3 2 1 0 8 7 6 5 FC-AL address ID (decimal) Left switch setting Right switch setting 0 0 0 1 0 1 . . . . . . . . . 15 0 F 16 1 0 . . . . . . . . 31 1 F 32 2 0 ...

  • EMC FC4500 - page 77

    3 Installing an SP or SP Filler Module 3-29 Ser vicing and Upgrading a DPE 2. At the back of the deskside DP E, gently insert the SP or filler module as sho wn below . Figur e 3-19 Installing an SP or SP Filler Module A. Open t he ejec tors a s f ar as possib le ; then gen tly pu sh the modu le int o the enclos ure guides , supporting it at bo th s ...

  • EMC FC4500 - page 78

    3 3-30 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE If you just install e d an SP filler module, yo u ar e done. Remove and stor e the ESD w ristband. If you just i nstalled a r eplacement or add-on SP , continue to the next step. 3. I nst all or r einst all the G BIC con nec tor( ...

  • EMC FC4500 - page 79

    3 Replacing or Ad ding an LCC Mod ule 3-31 Ser vicing and Upgrading a DPE Figur e 3-20 Remo ving an LCC Filler Module Proceed to the LCC installation procedure (page 3-32) a n d install the new add-o n LCC. 2. If r equired, r emove any cable from the LCC expansion (EXP) port as sho wn below . Figur e 3-21 Remo ving a Copper Cable fr om an LCC B. Gr ...

  • EMC FC4500 - page 80

    3 3-32 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE 3. Remove the LCC fr om its slot, as shown below . After removing an LCC, wait 6 second s befor e inserting it or another LCC. The wait allows the Core Softwar e to discover that the LCC has been r emoved. Continue to the next sec ...

  • EMC FC4500 - page 81

    3 Replacing or Ad ding an LCC Mod ule 3-33 Ser vicing and Upgrading a DPE Figur e 3-22 Installing an LCC Module The LCC Active light turn s on. The activity lights of any affected disk modu les should resume a steady f licker . If the disk activit y lights do not flicker w ithin 6 secon ds, r emove the LCC and insert it agai n. 2. If you are instal ...

  • EMC FC4500 - page 82

    3 3-34 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-23 Reconnecting a Copper Cable to an Expansion LC C 3. Y ou have replaced the LCC. Re move and stor e the ESD wristband . Replacing the Dr iv e Fan P ack CAUTION ! Handle a fa n pack gently a nd use an ES D wristband. Do ...

  • EMC FC4500 - page 83

    3 Replacing the Drive F an Pack 3-35 Ser vicing and Upgrading a DPE Removing the Drive Fan Pa ck Figur e 3-24 Remo ving the Drive Fa n Pac k As soon as the pack is disconnected fr om each power supply , the drive fan pack Check lig ht turns off, if it was not al r eady off; the DPE Check light on the front panel turns on, if it wa s not alr eady on ...

  • EMC FC4500 - page 84

    3 3-36 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-25 Installing the Drive F an Pac k A s s o o n a s t he p ac k i s i n p la c e, t he f a ns s t ar t s pi n ni n g ; t h e D P E Ch e c k light turns off if no oth er CRUs ar e faulty; and the Co oling Check light on ea ...

  • EMC FC4500 - page 85

    3 Replac ing or Adding a P ow er -Supply Mod ule 3-37 Ser vicing and Upgrading a DPE If one power supply is of f and th e other is on, do not turn one on and immediat ely tur n off t he other . I nstead, tu rn one on and wait five secon ds befor e turni ng the other off. If you ar e adding a new power supply , remove the power-supply filler module ...

  • EMC FC4500 - page 86

    3 3-38 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-27 Remo ving the T op Filler Module 3. Ins tall a power supply in the empty slo t as explain ed on page 3-41. Remo ving a Po we r -Supply Mo dule CAUTION ! T urn of f the power supply before unplugging the ac line cord f ...

  • EMC FC4500 - page 87

    3 Replac ing or Adding a P ow er -Supply Mod ule 3-39 Ser vicing and Upgrading a DPE Figur e 3-28 T urning off a Supply ’s Po wer and Unplugging the AC Lin e Cord Bottom power supply Top power s upply Power swit ch ac inle t ac inlet Power switch Channel ac power cord (right-angle plug) For each pow er supply to be removed: a . Set the power supp ...

  • EMC FC4500 - page 88

    3 3-40 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE 3. Remove the pow er -supply mod ule, as shown in Fig ur es 3-29 and 3-30. Figur e 3-29 Remo ving the T op Pow er -Supply Module Latch A. With your thumb , push the latch up and then right as far as possib le. B. Grasp the handle ...

  • EMC FC4500 - page 89

    3 Replac ing or Adding a P ow er -Supply Mod ule 3-41 Ser vicing and Upgrading a DPE Figur e 3-30 Remo ving the Bottom P ow er -Supply Module Inst al lin g a Powe r - S up pl y Module The top power supply i s inverted with r espect to the bottom power supply . A. With your thumb , push the latch down, and then left, as f ar as possible . B. Grasp t ...

  • EMC FC4500 - page 90

    3 3-42 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE Figur e 3-31 Installing the Bottom P ow er Supply Slot Latch C. With your thumb, push the latch right until it snaps up. B. Align the supply with the enclosure slot and gently push it into the slot until the latch moves to the mid ...

  • EMC FC4500 - page 91

    3 Replac ing or Adding a P ow er -Supply Mod ule 3-43 Ser vicing and Upgrading a DPE Figur e 3-32 Installing the T op Pow er Supply Latch Slot B. Align the module with the slot and gently push it into the slot until the latch moves to the middle of the slot. A. Make sure the module ’ s latch is as far right in its slot as possible. C. With your t ...

  • EMC FC4500 - page 92

    3 3-44 EMC Fibre Channel D isk-Array Pr ocessor Encl osure (DPE) Hardware Ref erence Servic in g an d Upgr adi ng a DPE 4. Plug the ac line cord into the new supply , and turn on its power as shown be low . 5. Rei nstall the drive fan pa ck as show n on page 3-35. Figur e 3-33 Plugging in the A C Line Cord and T ur ning on P ow er Bottom power supp ...

  • EMC FC4500 - page 93

    T e chnical Specifications and Ope r ating Limits A-1 A Invisible Body T ag This appendix d e scribes the DPE techn ical specifications, operating limits, and sh ipping and storage requirements. T echnical Specifications T e chnical specifications include power requirements, size, drive, interface, and st andards informatio n. AC Po we r Requiremen ...

  • EMC FC4500 - page 94

    A A-2 EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference T echnical Specification s and Operating Limits Size and W eight Requirement Des crip tion ac line voltage 100 to 240 V ac + 10%, single phas e , 47 to 63 Hz ac line curren t 8.0 A max estimate at 100 V (fully configured) P ower consumption 800 V A max estimate (ful ...

  • EMC FC4500 - page 95

    A T echnical Spec if ications A-3 T echnical Specifications and Operating Limits Drive Type 3.5-inch drives, Fibr e Channel interface, 2.54 cm (1.0-inches) or 4.06 cm (1.6-in ches) tall. SP Optical Ca bling The SP optical cable interface to the external Fibre Channel environment is as fo llows: LCC Coppe r Cabling The DPE ’ s LCC expansion port i ...

  • EMC FC4500 - page 96

    A A-4 EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference T echnical Specification s and Operating Limits Safety Standards EMI Standards Fibre Channel Related Standards St anda r d De scri pti on CSA 22.2 No . 950 Safety of Inf ormation T echnology Equipment including Electrical Bus ine ss E qui pm ent UL 1950 Safety of In ...

  • EMC FC4500 - page 97

    A Oper a ting Li mit s A-5 T echnical Specifications and Operating Limits Operating Limits The ambient temperature specification is measured at the fr ont door inlet. The site must have air conditioning of the corr ect size and placement to maintain the specified ambient temperatur e range. The air conditioning must be able to handle the BTU r equi ...

  • EMC FC4500 - page 98

    A A-6 EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference T echnical Specification s and Operating Limits Shipping and Sto rage Requirements Requirement Des crip tion Ambient temperatur e -40 ° C to 65 ° C ( -40 ° F to 149 ° F) T emperature gradient 25 ° C/hr (77 ° F/ hr) Relative humidity 10% to 90% nonco ndensing E ...

  • EMC FC4500 - page 99

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e g-1 Glossar y The terms defined her e are important to installin g and maintai ning a storage system. A ALP A (arbitrated loop ph ysical address) An 8-bit address that uniquely identifies an SP (or other device) on an F C-AL lo op. bind In the context of a disk-array st ...

  • EMC FC4500 - page 100

    g-2 EMC Fi bre Channel Disk-Array Processor Enclosure (DPE) Hardware Reference Glossa ry DPE (Disk-Arra y Processor Enclosure) A storage device that includes an en closure, up to 10 disk module s, one or two S Ps, one or two Fibre Ch annel LCCs, and one or two power supplies. A DPE can support up to 1 1 DAEs (each with up to 10 disk modules) in add ...

  • EMC FC4500 - page 101

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e g-3 Glossar y Fibre Channel host bus adapter (FC adapter) The name for the printed-circuit boar d within the computer chassis that allows the server to acce ss the Fibre Channel loop and thus the SP(s). field-replaceable unit See FRU (field-replaceable un it) . FRU (fie ...

  • EMC FC4500 - page 102

    g-4 EMC Fi bre Channel Disk-Array Processor Enclosure (DPE) Hardware Reference Glossa ry N node Any d evice wi th a Fibre Cha nnel inte rface (su ch as an HBA i n a server or a storage s ystem ’ s SP) that connects to a Fibre Channel loop. P PDU (power distribution unit) A device for the distribution of ac li ne power fr om one inlet to multiple ...

  • EMC FC4500 - page 103

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e g-5 Glossar y SP (stor age processor) A printed-cir cuit boar d with proces sor memory modules and control logic that manages the storage-system I/O between the server FC ada pter and the disk modules. SP memo ry module A m e mo ry m od u le (DI MM ) th at pro vi des t ...

  • EMC FC4500 - page 104

    g-6 EMC Fi bre Channel Disk-Array Processor Enclosure (DPE) Hardware Reference Glossa ry ...

  • EMC FC4500 - page 105

    EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e i-1 A ac line c ord attac hing to powe r supply 2-12 , 3-44 removing from power supply 3-39 ac power , current draw A-1 Active light , DPE compon ents 3-2, 3-3 adding disk modu le 3-9 LCC 3- 30 power supply 3-36 SP 3-26 addr essing r equir ements 2-2 ALP A (Arbitrated L ...

  • EMC FC4500 - page 106

    EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference i-2 Index adding 3-30 description 1-11 installin g 3-32 repl acing 3-3 0 memory modules installin g 3-24 removi ng 3-24 power issues 3-4 power supply adding 3-36 repl acing 3-3 6 power supply, description 1-13 SP adding 3-26 installin g 3-27 SP fa n pack description 1-14 ...

  • EMC FC4500 - page 107

    i-3 EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e Inde x replac ing 3-34 statu s ligh t 3-4 drives, disk 1-12 E EA (enclosu re a ddress ) about 2- 2, 2-3 defined g-2 ligh ts 1-8, 3-2 EMI (elec troma gnetic inte rfer ence) defined g-2 standa rds, cert ificatio n/compl iance A -4 enclosure 1-4 description 1-4 front p ...

  • EMC FC4500 - page 108

    EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference i-4 Index lights 1-12 reatta ching copper cables to 3-34 removing copper cables fr om 3 -31 repl acing 3-3 0 length r est rictions copper cabling A-3 lights DPE stat us 3-3 LCC 3-33 SP 1-9 lights, DPE status 3-2 loop envir onment 2-3 loos e cable 2-2, 2-1 3 M memory modul ...

  • EMC FC4500 - page 109

    i-5 EMC Fibre Chan nel Disk- Arr ay Proces sor Enc losure (DPE) Hardware Referenc e Inde x installi ng 3-27 lights 1-10 memory module locatio n of 1-10 memory modules g-5 installi ng 3-24 remo ving 3-2 4 optical cab ling, specs A-3 setting the addr ess ID 3-28 statu s ligh ts 3-3 spe cificat ions, D PE A-1 SPS (standby power supply) defined g-5 sta ...

  • EMC FC4500 - page 110

    EMC Fibre Cha nnel Disk-Array Pr ocessor En c losure (DPE) Hardware Reference i-6 Index ...

Manufacturer EMC Category TV DVD Combo

Documents that we receive from a manufacturer of a EMC FC4500 can be divided into several groups. They are, among others:
- EMC technical drawings
- FC4500 manuals
- EMC product data sheets
- information booklets
- or energy labels EMC FC4500
All of them are important, but the most important information from the point of view of use of the device are in the user manual EMC FC4500.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals EMC FC4500, service manual, brief instructions and user manuals EMC FC4500. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product EMC FC4500.

Similar manuals

A complete manual for the device EMC FC4500, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use EMC FC4500 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of EMC FC4500.

A complete EMC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual EMC FC4500 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the EMC FC4500, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the EMC FC4500, that we can find in the current document
3. Tips how to use the basic functions of the device EMC FC4500 - which should help us in our first steps of using EMC FC4500
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with EMC FC4500
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of EMC FC4500 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning EMC FC4500?

Use the form below

If you did not solve your problem by using a manual EMC FC4500, ask a question using the form below. If a user had a similar problem with EMC FC4500 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)