English dropdown-ico

Manual Moog Videolarm WS2C-50NA-X2

16 pages Not applicable
Download

Go to site of 16

Summary
  • Moog Videolarm WS2C-50NA-X2 - page 1

    PR ODUCT INSTR UCTIONS INST ALLA TION PREP ARA TION 1. Determine the mounting location. Be sure that you'll be mounting to a secure wall or ceiling. W e also recommend that for outdoor applications the housing be mounted in a protected area. 2. Complete all wire and conduit runs prior to installation. 3. The WS2 and WS4 are designed to be moun ...

  • Moog Videolarm WS2C-50NA-X2 - page 2

    - 2 - CAMERA BRA CKET SETUP (Figure 5) Reattach the brack et assembly to the back bo x using the two 10-32 x 3/8" screws . NO TE: For ceiling mount applications do not fully tighten immediately . Figure 2 1. Connect the output of your Class 2 P ower Supply to the terminal connectors on the PC Board inside the housing. Refer to the T roubleshoo ...

  • Moog Videolarm WS2C-50NA-X2 - page 3

    - 3 - Figure 6 CAMERA FOCUSING Fixed Lens: Loosen the set screw in the lens mount and to manually rotate the lens until a clear picture is achie ved. Once the focus is set, retighten the set scre w (Figure 6). Set screw Fixed lens V ari-Focal Lens: First, adjust the Magnifi cation Lock Screw to the desired magnifi cation (telephoto to wide angle) ...

  • Moog Videolarm WS2C-50NA-X2 - page 4

    - 4 - The operational settings f or the camera are defi ned by ten dip switches located on the PC Board (Figure 9). Moving the switches to the on position will activate each setting. Factory defaults are pictured below (Figure 10 and 11). F A CT OR Y DEF A UL T FIXED AND FIXED V ARI-FOCAL LENSES: Dip Switches 5 and 7 on, all others off. Figure 10 ...

  • Moog Videolarm WS2C-50NA-X2 - page 5

    - 5 - NO TE: This hi-res color camera uses a 1/4" chip and a 3-6mm auto iris lens. It is comparable to a 1/3" chip using a 4-9mm auto iris lens. The operational settings are defi ned by f our dip switches located on the side of the PC Board (Figure 12 and 13). Moving the switches to the UP position will activate specifi c settings. Refe ...

  • Moog Videolarm WS2C-50NA-X2 - page 6

    - 6 - Wiring Notes Wire — What to DO 1. DO use point-to-point Unshielded T wisted P air wire, gauge 24 or thick er , stranded or solid, Categor y 2, 3, 4, or 5. 2. The video signal may co-e xist in the same wire bundle as other video , telephone, data, control signals , or low-v oltage power . It is also OK to run NVT video signals in or near ele ...

  • Moog Videolarm WS2C-50NA-X2 - page 7

    250 ft 250 ft 3 4 5 8 13 1 300 ft 300 ft 4 5 6 10 16 1 400 ft 400 ft 5 6 8 13 21 1 500 ft 500 ft 6 8 10 16 26 1 600 ft 600 ft 8 10 12 19 31 1 800 ft 800 ft 10 13 16 25 42 1 1 0 0 0 f t 13 16 20 32 52 1 1 2 5 0 f t 16 20 25 40 65 1 1 5 0 0 f t 19 24 30 48 78 1 1 7 5 0 f t 23 28 35 55 91 1 2 0 0 0 f t 26 32 40 63 104 1 2 5 0 0 f t 32 40 49 79 131 1 3 ...

  • Moog Videolarm WS2C-50NA-X2 - page 8

    ! CAUTION RISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE. SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read befor e the unit is operated. 2. Retain Instructions - The safety and operating instructions should ...

  • Moog Videolarm WS2C-50NA-X2 - page 9

    P ower Supply P ower A P ower B Camera Assembly Primar y Po w e r Video Signal Video Shield Monitor - 10 - (Ground Return) Figure A Ground Loop TR OUBLESHOO TING If you e xper ience problems with the camera picture please chec k these simple troubleshooting procedures f or possible solutions before calling technical suppor t. IMPORT ANT NO TE: If y ...

  • Moog Videolarm WS2C-50NA-X2 - page 10

    AC V oltmeter Camera Monitor Bridge Tap NV-213 A NV-213 A - 11 - NVT TROUBLESHOO TING If you are e xper iencing problems , attempt to simplify your setup . T est each cable segment separately . F or example , test the camera and monitor together without the other equipment. Then add in the NVT transceiv ers, bac k-to-back. T est each segment of a l ...

  • Moog Videolarm WS2C-50NA-X2 - page 11

    - 12 - Depending on the voltage being used, ref er to one of the formulas below to select the correct pow er supply for camer as connected in parallel (positive to positiv e, negative to negativ e): T otal current for a 12 VDC system: T O T AL CURRENT = (350mA x total number of cameras) Example: 350mA x 5 total cameras = 1750mA T otal current for a ...

  • Moog Videolarm WS2C-50NA-X2 - page 12

    6 5 4 3 2 1 7 - 13 - WS2 - Exploded Diagram ...

  • Moog Videolarm WS2C-50NA-X2 - page 13

    - 14 - WS2 - Replacement P ar ts List Part Number Description 1 RPWS2010 W ARRIOR 2 & 4 BASE ASSEMBL Y 2 RPWS2020 W ARRIOR 2 & 4 CARRIAGE ASSEMBL Y KIT NTSC BOARD CAMERAS 3 RPWS1041F W ARRIOR 1 & 2 ST ANDARD RES, BLACK & WHITE, FIXED CAMERA KIT RPWS1041V WARRIOR 1 & 2 ST ANDARD RES, BLACK & WHITE, V ARIFOCAL CAMERA KIT RPWS1 ...

  • Moog Videolarm WS2C-50NA-X2 - page 14

    7 6 5 4 3 2 1 - 15 - WS4 - Exploded Diagram ...

  • Moog Videolarm WS2C-50NA-X2 - page 15

    - 16 - WS4 - Replacement P ar ts List Part Number Description 1 RPWS2010 W ARRIOR 2 & 4 BASE ASSEMBL Y 2 RPWS2020 W ARRIOR 2 & 4 CARRIAGE ASSEMBL Y KIT NTSC BOARD CAMERAS 3 RPWS3041F W ARRIOR 3 & 4 ST ANDARD RES, BLACK & WHITE, FIXED CAMERA KIT RPWS3041V W ARRIOR 3 & 4 ST ANDARD RES, BLACK & WHITE, V ARIFOCAL CAMERA KIT RPWS ...

  • Moog Videolarm WS2C-50NA-X2 - page 16

    Pr oduct Registr ation / W arr anty Thank y ou f or choosing Videolarm. W e value y our patr onage and ar e solely committ ed to pr oviding y ou with only the highest quality pr oducts av ailable with unmatched customer service lev els that ar e second-t o-none in the security industr y . Should a pr oblem arise, r est assure that Videolarm stands ...

Manufacturer Moog Videolarm Category Security camera

Documents that we receive from a manufacturer of a Moog Videolarm WS2C-50NA-X2 can be divided into several groups. They are, among others:
- Moog Videolarm technical drawings
- WS2C-50NA-X2 manuals
- Moog Videolarm product data sheets
- information booklets
- or energy labels Moog Videolarm WS2C-50NA-X2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Moog Videolarm WS2C-50NA-X2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Moog Videolarm WS2C-50NA-X2, service manual, brief instructions and user manuals Moog Videolarm WS2C-50NA-X2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Moog Videolarm WS2C-50NA-X2.

Similar manuals

A complete manual for the device Moog Videolarm WS2C-50NA-X2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Moog Videolarm WS2C-50NA-X2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Moog Videolarm WS2C-50NA-X2.

A complete Moog Videolarm manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Moog Videolarm WS2C-50NA-X2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Moog Videolarm WS2C-50NA-X2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Moog Videolarm WS2C-50NA-X2, that we can find in the current document
3. Tips how to use the basic functions of the device Moog Videolarm WS2C-50NA-X2 - which should help us in our first steps of using Moog Videolarm WS2C-50NA-X2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Moog Videolarm WS2C-50NA-X2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Moog Videolarm WS2C-50NA-X2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Moog Videolarm WS2C-50NA-X2?

Use the form below

If you did not solve your problem by using a manual Moog Videolarm WS2C-50NA-X2, ask a question using the form below. If a user had a similar problem with Moog Videolarm WS2C-50NA-X2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)