English dropdown-ico

Manual Perle Systems 5500208-41

93 pages 1.46 mb
Download

Go to site of 93

Summary
  • Perle Systems 5500208-41 - page 1

    IOLAN DS1/TS2 Command Line Interface Reference Guide Version 4.1 Part #5500208-41 October 2009 ...

  • Perle Systems 5500208-41 - page 2

    Copyright S tatement This document must not be repro duced in any way whatsoever , either printed or electronicall y , without the consent of: Perle Systems Limi ted, 60 Renfrew Drive Markham, ON Canada L3R 0E1 Perle reserves the right to make change s without further notice, to any products to improve reliability , function, or design. Perle, the ...

  • Perle Systems 5500208-41 - page 3

    IOLAN DS1/TS2 CLI Refere nce Guide, V ersion 4.1 3 Preface ........................ ....................................................... 11 About This Book .............. .................................... ...................... 11 Intended Audience .......... .................................... ...................... 11 Typeface Conventions ...

  • Perle Systems 5500208-41 - page 4

    4 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 Show Server ............. ................................................. ................ .............. 20 Hardware Commands ........... .............................. ........................ 20 Set Ethernet ......... ........................................................... .............. .. ...

  • Perle Systems 5500208-41 - page 5

    5 Show Sessions ................... ............................ .............. ............... ........... 30 Show Termtype .......... ................ .................................................. ........... 30 Start ................ ................................. .............................. ............... ........... 30 Telnet ..... ...

  • Perle Systems 5500208-41 - page 6

    6 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 Show Interface ......... ................ ................................................. .............. 55 Show Modbus............. ................................................. ................. ........... 55 Show Telnet-Client..... ................................. ........................ ...

  • Perle Systems 5500208-41 - page 7

    7 Set Gateway .......... ............................ ............................ ............... ........... 65 Show Gateways ........... ................................. ................ ............... ........... 65 Logging Commands .............. .............................. ...................... 66 Set Syslog ........... ................ ...

  • Perle Systems 5500208-41 - page 8

    8 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 Set MOTD ......... ................................................. ............................ ........... 73 Show MOTD ................ ................. ................................ ................. ........... 73 Chapter 8 Statistic Commands ........................................ 75 Con ...

  • Perle Systems 5500208-41 - page 9

    9 Set IOChannel IOExtension ..... ............... ................................. .............. 88 Set IOChannel Multihost ......... ................................. ................ .............. 90 Show IOChannel Status ........ .......................................... .............. ......... 90 Kill IOChannel ............ ............... ...

  • Perle Systems 5500208-41 - page 10

    10 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 ...

  • Perle Systems 5500208-41 - page 11

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 1 1 Preface About This Book This guide provides the information you need to configure the IOLAN using the Comm and Line Interface (CLI). Intended Audience This guide is for adm inistrators who w ill be configuring th e IOLAN. Some prerequisite knowledge is needed to understand the concep ts and examp ...

  • Perle Systems 5500208-41 - page 12

    Contacting T echnical Support 12 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 Cont acting T echnical Support Making a T echnical Support Query Who T o Cont act Note: Perle offers free technical suppo rt to Perle Authori sed Distributors and Registered Perle Resellers. If you bought your produ ct from a registered Perle supplier , you must contac ...

  • Perle Systems 5500208-41 - page 13

    13 Contacting T echnical Support Rep air Procedure Before sending a IOLAN for repair, you must contact your Perle supplier . If, however , you bought your product directly from Perle you can contact direct ly . Customers who are in Europe, Afri ca or Middle East can submit repair d etails via a websit e form. This form is on the Perle website, www ...

  • Perle Systems 5500208-41 - page 14

    Contacting T ech nical Support 14 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 ...

  • Perle Systems 5500208-41 - page 15

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 15 Introduction Chapter 1 1 Introduction This chapter provides the command line interface (CLI) options availabl e for the IOLAN. The commands are grouped by function. CLI Conventions This section explains how to interp ret the CLI synt ax.If you are an existing T erminal Server customer and would li ...

  • Perle Systems 5500208-41 - page 16

    CLI Conventions 16 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 z Options —Provides an explanation of each of the op tions for a command and the default value if there is one. Some commands do not have any option s, so this category is absent. Command Shortcut s When you type a command, you can specify the shortest unique ve rsion of that comm ...

  • Perle Systems 5500208-41 - page 17

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 17 Server Commands Chapter 2 2 This chapter defines all the CLI commands asso ciated with co nfiguring the IOLAN’ s server parameters. Server Commands Set Custom-App Description Y ou can create a custom application that can run on the IOLAN using the Perle SDK. User Level Admin Syntax Options pr og ...

  • Perle Systems 5500208-41 - page 18

    Server Commands 18 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 banner This parameter concerns the b anner informa tion (product name/so ftware version). This banner information is presente d to a user with a login prompt. For security reasons, you can turn off the display of this information. The default is Off . break Enables/disables the exis ...

  • Perle Systems 5500208-41 - page 19

    19 Server Commands Set Service promp t-with-name Displays the Server Name field value instead of defau lt product name. When enabled, the Server Name is displaye d in the IOLAN login prompt, CLI prompt, W ebManager login screen, and the heading of the Menu. The default valu e is Off . single-telnet In this mode of operation, the IOLAN will only all ...

  • Perle Systems 5500208-41 - page 20

    Hardware Commands 20 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 Show Custom-App Description Shows the custom appli cation server settings. User Level Admin Syntax Show Modbus Description Shows the Modbus settings for the gateway . User Level Normal, Admin Syntax Show Server Description Shows the parameters set for the server . User Level Admin ...

  • Perle Systems 5500208-41 - page 21

    21 Modbus Commands Modbus Commands Set Modbus Gateway Description Sets the Modbus parameters for the IOLA N wh en it is operating as a Modbus Gateway . User Level Admin Syntax Options addr -mode broadcast char -timeout req-next -delay exceptions idle-timer mess-timeout port req-qu euing rem ap p ed -i d set modbus gateway [addr-mode embedded|re-map ...

  • Perle Systems 5500208-41 - page 22

    T ruePort Baud Commands 22 IOLAN DS1/TS2 CLI Reference Guide, V ersion 4.1 Show Modbus Description Displays the Modbus Gateway parameters. User Level Admin Syntax T ruePort Baud Commands Set T ruePort Remap-Baud Description This command allows for the remapping of th e baud rate being specified by the Serial application to a different value on th e ...

  • Perle Systems 5500208-41 - page 23

    23 IPv6 Commands IPv6 Commands Set IPv6 Description Configures the basic IPv6 settings. User Level Admin Syntax Options dhcpv6-settings ivp6-addr ess network-prefix enable-ipv 6-addr essing obtain-using auto-ipv6|dh cpv6 z auto-ipv6 —When enabled, the IOLAN will send out a Router Solicitation message. If a Router Advert isement message is receive ...

  • Perle Systems 5500208-41 - page 24

    IPv6 Commands 24 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Add Custom-IPv6 Description Adds a custom IPv6 address to the IOLAN. Y ou can specify either a complete IPv6 address or an IPv6 network address. User Level Admin Syntax Options met hod auto network-prefix prefix-bits (auto) method manual ipv6-addr ess prefix-bits (manual) Set Custom- ...

  • Perle Systems 5500208-41 - page 25

    25 IPv6 Commands Delete Custom-IPv6 Description Deletes the specified custom IPv6 address. T o see a list of configured IPv6 addresses, type the command delete custom-ipv6 ? . User Level Admin Syntax prefix-bits (auto) Specify the network prefix bits for the IPv6 address. Range: 0-64 Default: 64 method manual Specify this option when you want to en ...

  • Perle Systems 5500208-41 - page 26

    IPv6 Commands 26 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 ...

  • Perle Systems 5500208-41 - page 27

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 27 User Commands Chapter 3 3 This chapter defines all the CLI commands avai lable to users who are logged into the IOLAN. Commands for Users Logged Into the IOLAN Admin Description Changes a Normal-level user to the Admin user . When you press Enter after you type this command, you will be prompted f ...

  • Perle Systems 5500208-41 - page 28

    Commands for Users Logged Into the IOLAN 28 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Menu Description Switches from a command line based interface to Menu mode of operation. User Level Restricted, Normal, Admin Syntax Ping Description This command checks to see if a given host is reachable via an IP me ssage. The specific message used is ca ...

  • Perle Systems 5500208-41 - page 29

    29 Commands for Users Logged Into the IOLAN Set User Description Sets the current users settings. User Level Normal, Admin Syntax Options hotkey-p refix language password Set User Session Description Sets the current users session settings. User Level Normal, Admin Syntax Options sess ion Specifies the session number (or a ll, *) that you are confi ...

  • Perle Systems 5500208-41 - page 30

    Commands for Users Logged Into the IOLAN 30 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Show Line Users Description Shows the users who are on the line. User Level Admin Syntax Syslog Console Description Starts/stops or displays the status of the syslog console. User Level Admin Syntax Options start|stop Star t or stop console lo gging. Whe n ...

  • Perle Systems 5500208-41 - page 31

    31 Commands for Users Logged Into the IOLAN Te l n e t Description Starts a telnet session to the specified host/IP address. User Level Normal, Admin Syntax telnet < hostname/IP_address > [< tcp_por t >] [termtype < terminal_name >] [line-mode on|off] [map-cr-crlf on|off] [local-echo on|off] [echo <00-7f>] [eof <00-7f> ...

  • Perle Systems 5500208-41 - page 32

    Configuring Users 32 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Ve r s i o n Description Displays firmware version and build . User Level Normal, Admin Syntax Configuring Users Add User Description Adds a user . For units with 4 or less serial ports, you can configure up to 4 users. For units with 8 or mor e serial por ts, the maxi mum number ...

  • Perle Systems 5500208-41 - page 33

    33 Configu ring Users hotkey-pre fix The prefix that a user types to control the current session. The default value is hex 01 , which corresponds to Ctrl-a ( ^a ) (hex value 02 would be Ctrl-b (^b), etc. ): z ^a number —T o switch from one session to another , press ^a and then th e required session number . For example, ^a 2 would switch you to ...

  • Perle Systems 5500208-41 - page 34

    Configuring Users 34 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 line-access Specifies the user access rights to each IOLAN device line. Options are: z Read/Write —Users are given read an d write access to the line. z Read In —Users are given access to read only outbound dat a, data that is going from the IOLAN to the device. The on|off op ...

  • Perle Systems 5500208-41 - page 35

    35 Configu ring Users Set User Description Sets users settings. Normal-level users can configure only t heir own settings. Admin-level users can configure any users settin gs, including their own (with the exception of their User Level, which must st ay at Admin). User Level Normal, Admin Syntax set user . [hotkey-prefix <00 -7f>] [language e ...

  • Perle Systems 5500208-41 - page 36

    Configuring Users 36 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 level The access that a user is allowed: z Admin —The admin level user has total access to the IOLAN. Y ou can create more than one admin user account but we recomm end that you only have one. They can monitor and configure t he IOLAN. z Normal —The Normal level user has limi ...

  • Perle Systems 5500208-41 - page 37

    37 Configu ring Users Set User Session Description Configures a users session settings. See Set User Ses sion on page 29 for the options descriptions. User Level Admin Syntax Show Default User Description Shows the Default Users settings. When addi ng a new user , th e profile of the default user will be used to assign the values of the parame ters ...

  • Perle Systems 5500208-41 - page 38

    Configuring Users 38 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 ...

  • Perle Systems 5500208-41 - page 39

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 39 Line Commands Chapter 4 4 This chapter defines all the CLI commands associat ed with configuring the IOLAN ’ s line parameters. 1-Port vs. 2-Port Line Commands If you are using a DS1 IOLAN, the admin user does not have the option of using the number or all (*) options in the line comman ds, as t ...

  • Perle Systems 5500208-41 - page 40

    Line Commands 40 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Options br eak Specifies how a break is interpreted: z off —The IOLAN ignores the break key completely and it is not passed through to the host. This is the default setting. z local —The IOLAN deals with the break locally . If the user is in a session, the break key has the same ...

  • Perle Systems 5500208-41 - page 41

    41 Line Commands hotkey-pre fix The prefix that a user types to lock a line or redraw the Menu. The default value is h ex 01 , which corresponds to Ctrl-a ( ^a ) (hex value 02 would be Ctrl-b (^b), etc.): z ^a l —(Lowercase L) Locks the line until the us er unlocks it. The user is prompted for a password (any password, excluding spaces) and locks ...

  • Perle Systems 5500208-41 - page 42

    Line Commands 42 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 lock When enabled, the user can lock hi s terminal with a password using the Hotkey Prefix (default Ctrl-a) ^a l (lowercase L). The IOLAN prompts the user for a password and a confirmation. mode Enables/disables the line (ava ilable only on the TS2 model). The default is enabled. mod ...

  • Perle Systems 5500208-41 - page 43

    43 Line Commands sess-timer Enter a time, in seconds, for w hich the Session Timer will run. Use th is timer to forcibly close the session (connection). When the Session T imer expires, the IOLAN will end the connection. The default value is 0 seconds so the port will never timeout. The maximum value is 4294967 seconds (ab out 49 days). stop-bits S ...

  • Perle Systems 5500208-41 - page 44

    Line Commands 44 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set Line Interface Description Configures line interface (hardware) parameters. User Level Admin Syntax set line .|< number >|* interfa ce eia-232 [monitor-dcd on|off] [monitor-dsr on|off] [flow none|soft|hard|both] [speed 50|75|110|134|150|200|300|600| 1200|1800|2400|4800|9600 ...

  • Perle Systems 5500208-41 - page 45

    45 Line Commands Set Line Service echo-suppression This parameter applies only to EIA-485 Half Duplex mode. All characters will be echoed to the user and transmitted across the serial port s. Some EIA-485 applications require local echo to be enabled in order to monitor the loopback data to determine that line contentio n has occurred. If your appl ...

  • Perle Systems 5500208-41 - page 46

    Line Commands 46 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 < host_port > The port number the target host is listening on for incoming connections. direct Direct connections b ypass the IOLAN, enabling the user to log straight into a specific host. A direct connectio n is recommended where a user loggi ng in to the IOLAN is not required ...

  • Perle Systems 5500208-41 - page 47

    47 Line Commands Set Modem Description Sets the modem initialization string fo r a modem defined in the modem table. If you wish to add a new modem, use the add modem command. User Level Admin Syntax Options < mod em_name > Predefined modem name. < init_string > Specify the initialization string for the m odem. Th is c an b e up to 60 c ...

  • Perle Systems 5500208-41 - page 48

    Line Service Commands 48 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set T ermtype Description Sets the terminal type for th e current terminal session. term1, term2, and term3 refer to the user-uploadable custom terminal definitions . If these are not present, the default is wyse60. User Level Restricted, Normal, Admin Syntax Option wyse60|vt ...

  • Perle Systems 5500208-41 - page 49

    49 Line Service Commands Set T elnet-Client Description Configures the T elnet parameters for the sp ecified line. When the IOLAN initiates a T elnet connection to a host, it is acting as a T elnet client. User Level Normal, Admin Syntax Options termtype line-mode map-cr -crlf local-echo echo eof erase intr quit escape set telnet-client line .|< ...

  • Perle Systems 5500208-41 - page 50

    Line Service Commands 50 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set UDP Description Configures the UDP settings for the serial line. User Level Normal, Admin Syntax Options entry 1|2|3|4 Selects which of the 4 available entries we wish to define/modify . For each entry the user can specify a dif ferent IP address ra nge, UDP port and dire ...

  • Perle Systems 5500208-41 - page 51

    51 Line Service Commands Set Vmodem Description This command associates a phone number w ith an IP address and TCP p ort. This enables an existing modem application to i ssue a dial command with a phone number . The phone number will be searched in this table and if an exact match is found, the associated IP address and TCP port will be used to est ...

  • Perle Systems 5500208-41 - page 52

    Line Service Commands 52 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set Vmodem-Phone signals dtr Y ou can specify how the DTR signal pin acts during your modem application connection, as itself (DTR), as DCD, or as RI. signals rts Y ou can specify how the R TS signal pin acts duri ng your modem application connection, as itself (R TS), as DCD ...

  • Perle Systems 5500208-41 - page 53

    53 Line Service Commands Set Modbus-Slave Line Description Sets the Modbus slave pa rameters for the line. User Level Admin Syntax Options crlf protocol uid-range Set Modbus-Master Line < IP_address > Specify the IP address of the remote hos t that is receiving the vmodem connection. < TCP_port > Specify the TCP port that the remote hos ...

  • Perle Systems 5500208-41 - page 54

    Line Service Commands 54 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set Multihost Line Description Configures multiple hosts or a prim ary/back up host schema fo r Silent Raw , Reverse Raw , or Client-Initi ated T ruePort servi ce types (multihost must be enabled by the line service type for this to take effect, see Set Line Service on page 4 ...

  • Perle Systems 5500208-41 - page 55

    55 Line Service Commands Show Custom-App Description Shows the custom application line settings. User Level Admin Syntax Show Interface Description Shows the network interface information. User Level Admin Syntax Show Modbus Description Shows the Modbus settings for a line. User Level Admin Syntax Show T elnet-Client Description Shows the telnet cl ...

  • Perle Systems 5500208-41 - page 56

    Modem Commands 56 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Modem Commands Add Modem Description Adds a modem. User Level Admin Syntax Options < mod em_name > < initialization_ string > Delete Modem Description Deletes a modem. User Level Admin Syntax Option < config_modem_name > Y ou can see a the list of modems that can b ...

  • Perle Systems 5500208-41 - page 57

    57 Packet Forwarding Commands Packet Forwarding Commands Set Packet-Forwarding Line Description The Packet Forwarding feature allows you to control how the data coming from a serial device is packetized before forwarding the packet onto the LA N network. This command configures packet forw arding options for serial devi ces attached to the serial l ...

  • Perle Systems 5500208-41 - page 58

    Packet Forwarding Commands 58 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 custom-on-specific-events This section allows you to set a variety of packet definition options. The first criteria that is met causes the packet to be transmitted. For example, if you set a Force Tr a n s m i t T i m e r of 1000 ms and a Packet Size of 100 bytes, whiche ...

  • Perle Systems 5500208-41 - page 59

    59 Packet Forwarding Commands Show Packet-Forwarding Line Description Shows the packet-forwarding settings for the line. User Level Admin Syntax force-transmit-timer When the specified amount of time, in milliseconds, elapses after the first character is received from the serial port, th e packet is transmitted. After a packet is transmitted, the n ...

  • Perle Systems 5500208-41 - page 60

    Packet Forwarding Commands 60 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 ...

  • Perle Systems 5500208-41 - page 61

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 61 Network Commands Chapter 5 5 This chapter defines all the CLI commands asso ciated with co nfiguring the IOLAN’ s network parameters. SNMP Commands The IOLAN supports SNMP traps for restar t and SNMP communi ty authentication error . Add Community Description Adds an SNMP community (version 1 an ...

  • Perle Systems 5500208-41 - page 62

    SNMP Commands 62 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Delete Community Description Deletes an SNMP community (version 1 and version 2). User Level Admin Syntax Option < config_community_number > When you add an SNMP communi ty , it gets assigned to a number . T o delete the SNMP community , you need to specify the number of the co ...

  • Perle Systems 5500208-41 - page 63

    63 TFTP Commands TFTP Commands Set Server TFTP Description Configures the IOLANs TFTP client settings. User Level Admin Syntax Options retr y timeout Host s Commands Add Host Description Adds a host to the IOLAN host table. User Level Admin Syntax Options < hostname > < ip_address > Delete Host Description Deletes a host from the IOLAN ...

  • Perle Systems 5500208-41 - page 64

    Gateway Comma nds 64 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Show Host s Description Shows the IOLAN host table. User Level Normal, Admin Syntax Gateway Commands Add Gateway Description Adds a gateway . Y ou can configure up to twenty gateways. User Level Admin Syntax Options < config_host > default|host|network < dest_IP_addr > ...

  • Perle Systems 5500208-41 - page 65

    65 Gateway Commands Set Gateway Description Configures the gateway . User Level Admin Syntax Options < config_gateway_host > Y ou can view the configured gateways that can be d eleted by typing delete gateway ? . default|host|network < destinati on_ip > < prefixbits_mask > When the gateway is a Network gateway , you must specify t ...

  • Perle Systems 5500208-41 - page 66

    Logging Comma nds 66 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Logging Commands Set Syslog Description Configures the system log. User Level Admin Syntax Options level primary-host secondary-host Show Syslog Description Shows the syslog settings. User Level Admin Syntax set syslog [level emergency|alert|cr itical|error|warning|notice|info|de ...

  • Perle Systems 5500208-41 - page 67

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 67 T ime Commands Chapter 6 6 This chapter defines all the CLI commands a ssociated with configuring the IOLAN’ s time parameters. T ime Commands Set T ime Description Sets the IOLAN’ s system clock. User Level Admin Syntax Option < hh : mm [: ss ]> Sets the IOLAN’ s system time, using mi ...

  • Perle Systems 5500208-41 - page 68

    T ime/Date Setting Command s 68 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Show Date Description Shows the date, according to the IOLAN system clock. User Level Normal, Admin Syntax Show Time Description Shows the IOLAN’ s system clock. User Level Normal, Admin Syntax show date show time ...

  • Perle Systems 5500208-41 - page 69

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 69 Administration Commands Chapter 7 7 This chapter defines all the CLI commands associ ated with configuring the IOLAN ’ s ad ministration parameters. Bootup Commands Reboot Description Reboots the IOLAN. Y ou wi ll be prompted to save configurat ion to FLASH, if there have been unsaved configu ra ...

  • Perle Systems 5500208-41 - page 70

    Bootup Commands 70 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set Bootup Description Specifies remote the TFTP host and pathname for files to be loaded after a IOLAN reboot. User Level Admin Syntax Options firmwar e file configuration file host The host name or IPv4/IPv6 address of the se rver that contains t he configurati on or firmware fil ...

  • Perle Systems 5500208-41 - page 71

    71 TFTP File T ransfer Commands TFTP File T ransfer Commands Netload Description T ransfers a file from a remote host to the IOLAN using the TFTP protocol. User Level Admin Syntax Options text-config Specify this option i f you are uploading a text-based configuration file to the IOLAN from a TFTP server . factory-defa ult-config firmware Specifies ...

  • Perle Systems 5500208-41 - page 72

    Custom Factory Default 72 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Net save Description T ransfers a file from the IOLA N to a remote host using the TFTP protocol. User Level Admin Syntax Options configurat ion Specifies that you are going to upload a co nfiguration file from the IOLAN to the specified host or IP address. crash Specifies th ...

  • Perle Systems 5500208-41 - page 73

    73 MOTD Commands Set Description Sets the current configuration on IOLAN to act as the factory default configuration. See the User Guide for dir ections on ho w to rever t b ack to the original facto ry default configuration, if required. User Level Admin Syntax MOTD Commands Set MOTD Description Specifies the server/file that contains the mes sage ...

  • Perle Systems 5500208-41 - page 74

    MOTD Commands 74 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 ...

  • Perle Systems 5500208-41 - page 75

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 75 S t atistic Commands Chapter 8 8 This chapter defines all the CLI commands asso ciated with co nfiguring the IOLAN’ s statistic parameters. Configuration S t atistics Show Net stat Description Shows currently used TCP/UDP sockets/ports. User Level Admin Syntax Options all Displays all ports, inc ...

  • Perle Systems 5500208-41 - page 76

    Run-T i me S tatistics 76 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Show Net st at S tatistics Description Shows protocol (IP/IC MP/TCP/UDP) counters. User Level Admin Syntax Show Routes Description Shows current information about IPv4 or IPv6 network routes. User Level Admin Syntax Run-T ime St atistics Delete Arp Description Delete entries ...

  • Perle Systems 5500208-41 - page 77

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 77 I/O Commands Chapter 9 9 This chapter defines all the CLI commands associat ed with configuring the IOLAN’ s I/O parameters. Global I/O Commands Set IO UDP Description Sets the UDP settings fo r I/O unicast messages. User Level Admin Syntax Options mode broadcast-interval entry Y ou can specify ...

  • Perle Systems 5500208-41 - page 78

    Set Line 78 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set IO Failsafe Description Sets the failsafe (watchdog) settings for I/O. User Level Admin Syntax Options mode timeout Set IO Modbus Description Enabling the Modbus option makes the IOLAN act as a Modb us Slave, allowing Modbus Masters to communicat e with the IOLAN to control and/or ret ...

  • Perle Systems 5500208-41 - page 79

    79 Set IOChannel Set IOChannel Set IOChannel Mode Description Sets general I/O channel set tings for the sp ecified channel, these settings are available to all channels and I/O serial pins. User Level Admin Syntax Options i/o_channel Specify the channel number , for example, d2 or a4. T emperature models use Analog input, so the channel numbers ar ...

  • Perle Systems 5500208-41 - page 80

    Set IOChannel 80 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set IOChannel Digit al Input (Serial Pins) trigger When the trigger con dition is met, tr iggers the specified alarm action. T riggers can be: z Disabled —No alarm settings. This is the default. z Inactive —When the expected Digital input is active, going inactiv e will trigger a ...

  • Perle Systems 5500208-41 - page 81

    81 Set IOChannel Set IOChannel Digit al Output trigger When the trigger con dition is met, tr iggers the specified alarm action. T riggers can be: z Disabled —No alarm settings. This is the default. z Inactive —When the expected Digital input is active, going inactiv e will trigger an alarm. z Active —When the expected Digital input is in act ...

  • Perle Systems 5500208-41 - page 82

    Set IOChannel 82 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 type Specify the type of digital output: z Sink —Specifies that the channel will be grounded when active. z Sourc e —Specifies that the channel wi ll provide voltag e when active. z Sink and Sour ce —Specifies that channel will be grounded when it is inactive and will provide v ...

  • Perle Systems 5500208-41 - page 83

    83 Set IOChannel Set IOChannel Digit al Output (Serial Pins) Description Sets the Digital output for serial pins R TS and DTR. This option is only availa ble when the Line Service is set to Signal I/O . User Level Admin Syntax Options des cription failsafe-action mode Set IOChannel Relay set iochannel rts|dtr [descri ption < string >] [failsa ...

  • Perle Systems 5500208-41 - page 84

    Set IOChannel 84 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set IOChannel Analog (T rue Analog) active-to-inactive-delay When the I/O is commanded to an inactive state, this is the len gth of the delay b efore the command is executed. V alid values are 1-9999 x 10 0 ms. The default is 100 ms. inactive-to-active-delay When the I/O is commanded ...

  • Perle Systems 5500208-41 - page 85

    85 Set IOChannel alarm Configures alarm settings when the Analog input trigger is activated. level Y ou can specify up to five alarm tr igger/clear severity levels. If the Tr i g g e r Ty p e is Low , an alarm is triggered when th e input drops below the specified T rigger value; other severity level trigger va lues must decrease in value with each ...

  • Perle Systems 5500208-41 - page 86

    Set IOChannel 86 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set IOChannel Analog (T emperature) Description Sets the Analog input channel se ttin gs for T emperature models. User Level Admin Syntax set iochannel < analog_channel > type r td|thermocouple range < range_specifier > set iochannel < analog_channel > alarm [level ...

  • Perle Systems 5500208-41 - page 87

    87 Set IOChannel level Y ou can specify up to five alarm tr igger/clear severity levels. If the Tr i g g e r Ty p e is Low , an alarm is triggered when th e input drops below the specified T rigger value; other severity level trigger va lues must decrease in value with each subsequent level. If the Tr i g g e r Typ e is High , an alarm is triggered ...

  • Perle Systems 5500208-41 - page 88

    Set IOChannel 88 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set IOChannel IOExtension Description Configures the I/O extension options that allo w you to connect the Digital Input channel or input serial signal pin (when the line is confi gured for signal-io) to Digital Output/Relay channels or outp ut serial signal pins (when the line is con ...

  • Perle Systems 5500208-41 - page 89

    89 Set IOChannel connection-method The connection-metho d is one of the following: z Client-Initiated —When specified, the channel/seri al signal pin will wait for connections to be initiated by an othe r I/O channel or a TCP/IP application. z Server -Initiated —When specified, the channel/serial signal pin initiates communication to another I/ ...

  • Perle Systems 5500208-41 - page 90

    Set IOChannel 90 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 Set IOChannel Multihost Description Configures up to 49 hosts/IOLANs that the Di g ital input channel or input serial signal pins (DSR, DCD, or CTS-when the line is configured for signal -io) will connect to. T o see a list of configured hosts/IO LANs, enter the show iochannel < c ...

  • Perle Systems 5500208-41 - page 91

    91 Set IOChannel Show IO Description Shows global I/O information (for example, UDP , TruePort, Modbus). T emperature input is Analog. User Level Admin Syntax Options i/o_channel Specify the channel number , for example, d2 or a4. T emperature models use Analog input, so the channel numbers are a1-a4. rts|cts|dtr|dsr|dcd Specify the Digital output ...

  • Perle Systems 5500208-41 - page 92

    I/O Channel Control Commands 92 IOLAN DS1/TS2 CLI Reference Guide, V e rsion 4.1 I/O Channel Control Commands The I/O commands in this section are used to manual ly manage the I/O channels. Digit al Output Description Manages the Digital output channel status. No t all models have four digital channels, most have just two. User Level Admin Syntax O ...

  • Perle Systems 5500208-41 - page 93

    IOLAN DS1/TS2 CLI Referenc e Guide, V ersion 4.1 93 Glossary This chapter provides definitions for IOLAN terms. BOOTP (BOOT strap Protocol) An Internet protocol that enables a diskless workstation to discover its own IP address, the IP address of a BOOTP server on the network, and a file to be loaded into memory to boot the machine. This enables th ...

Manufacturer Perle Systems Category Server

Documents that we receive from a manufacturer of a Perle Systems 5500208-41 can be divided into several groups. They are, among others:
- Perle Systems technical drawings
- 5500208-41 manuals
- Perle Systems product data sheets
- information booklets
- or energy labels Perle Systems 5500208-41
All of them are important, but the most important information from the point of view of use of the device are in the user manual Perle Systems 5500208-41.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Perle Systems 5500208-41, service manual, brief instructions and user manuals Perle Systems 5500208-41. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Perle Systems 5500208-41.

Similar manuals

A complete manual for the device Perle Systems 5500208-41, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Perle Systems 5500208-41 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Perle Systems 5500208-41.

A complete Perle Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Perle Systems 5500208-41 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Perle Systems 5500208-41, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Perle Systems 5500208-41, that we can find in the current document
3. Tips how to use the basic functions of the device Perle Systems 5500208-41 - which should help us in our first steps of using Perle Systems 5500208-41
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Perle Systems 5500208-41
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Perle Systems 5500208-41 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Perle Systems 5500208-41?

Use the form below

If you did not solve your problem by using a manual Perle Systems 5500208-41, ask a question using the form below. If a user had a similar problem with Perle Systems 5500208-41 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)