English dropdown-ico

Manual MaxTech NX-16

14 pages 0.04 mb
Download

Go to site of 14

Summary
  • MaxTech NX-16 - page 1

    User's Guide NX-16 Series High Performance Software Configurable 16-bit ISA NE-2000 compatible Ethernet Adapters Part #MAN005 Rev. 1.1 ...

  • MaxTech NX-16 - page 2

    Please take a moment to note the following infor- mation. Include this form in the unlikly event that you need to return the product for warranty service. Refer to Section Eight for complete Warranty information and procedures on returning your product. Product: _________________________ Serial Number: ____________________ Purchase Date: __________ ...

  • MaxTech NX-16 - page 3

    1 Contents Section One - Introduction ......................... 1 Section Two - Installation ........................... 2 Section Three - Driver Installation .............. 7 Section Four - Troubleshooting .................. 7 Section Five - Cable Information .............. 9 Section Six - Specifications ..................... 10 Section Seven - Te ...

  • MaxTech NX-16 - page 4

    2 Minimum hardware requirements are an IBM PC/XT (or better) fully compatible PC with 512K RAM running DOS 3.3 or higher. The network operating system you use may have higher requirements. Section Two - Installation This section will provide step by step in- structions on how to install your new Maxtech network adapter. Installation of this network ...

  • MaxTech NX-16 - page 5

    3 2.2 Hardware Installation Installation of this adapter card requires opening and manipulating your PC. Exercise cau- tion at all times when working with AC powered and static-sensitive equipment. Turn off and un- plug your PC before installation. Discharge any static electricity from your body by touching any metal surface. 1. Turn off your compu ...

  • MaxTech NX-16 - page 6

    4 6. Carefully install the adapter by firmly press- ing the card into the slot you have chosen, applying even pressure until the adapter is completely seated in the slot. 7. Fasten the retaining bracket with the screw from the slot cover. Make sure the adapter is properly aligned. Store the slot cover for future use. 8. Replace the computer cover a ...

  • MaxTech NX-16 - page 7

    5 Running the SETUP program 1. Insert the installation diskette into your drive, log on to that drive, and run the SETUP program in the DIAG subdirectory. Assuming that your have inserted the dis- kette in drive A, you would type the follow- ing at the DOS C: drive prompt: A: [ENTER] DIAGSETUP [ENTER] 2. Select the network adapter that you would ...

  • MaxTech NX-16 - page 8

    6 2.4 Testing The Adapter The SETUP program provides an option in its main menu for adapter diagnostics. One or more PCs on the network can run the test simulta- neously. The Test Adapter option runs several tests and the results are indicated by either PASS or FAIL. Make sure that the network cable is attached (and properly terminated if using a B ...

  • MaxTech NX-16 - page 9

    7 sure that the notch on the ROM matches that on the socket (refer to Figure 2). 2. Configure the adapter using the SETUP program to enable the Boot ROM function by selecting the appropriate address from the Boot ROM Base Address option. Refer to Section 2.3 for more information on running the SETUP program. 3. Follow the Remote Boot Workstation in ...

  • MaxTech NX-16 - page 10

    8 README.TXT file describing the driver. Refer to the RELEASE.TXT file on the installation diskette for more information on the available drivers. Section Four - Troubleshooting This section describes some of the com- mon problems you may encounter while using your network adapter. When troubleshooting, you should make sure that the network you are ...

  • MaxTech NX-16 - page 11

    9 4.2 Cable Problems A) Observe the green Link Status LED if you are using a 10Base-T network. Turn on the computer. Connect the network cable and observe the green LINK LED. If the LED is ON, then the system is connected. Otherwise check for a proper RJ-45 connection. B) Make sure the coaxial cable is prop- erly terminated if you are using a 10Bas ...

  • MaxTech NX-16 - page 12

    10 must use solid copper conductors and UL codes CM, CMR, and CMP are required. The computer on the network is connected via a star topology (i.e. each node is connected to a HUB, not to each other). Maximum cable length is 300' (100 m). 10Base-2 networks uses a single conduc- tor coaxial cable and BNC connectors. Use only RG-58A/U or RG-58C/U ...

  • MaxTech NX-16 - page 13

    11 Section Seven - Technical Support In the unlikely event you experience difficulty in the use of the product, or if it does not operate as described, we suggest you: (1) consult the Troubleshooting section of this guide and (2) consult with your dealer. If you have not referred to the Troubleshooting section, there is a good chance the solution t ...

  • MaxTech NX-16 - page 14

    12 (also enclose a check for out-of-warranty repair). En- close your check or Postal Money Order for $7.50 to cover the cost of return shipping/handling. Please do not send cash or stamps. 4. After wrapping the package securely for shipping, print your name, return address and the RMA # clearly on the outside of your package. 5. Ship the unit prepa ...

Manufacturer MaxTech Category Network Card

Documents that we receive from a manufacturer of a MaxTech NX-16 can be divided into several groups. They are, among others:
- MaxTech technical drawings
- NX-16 manuals
- MaxTech product data sheets
- information booklets
- or energy labels MaxTech NX-16
All of them are important, but the most important information from the point of view of use of the device are in the user manual MaxTech NX-16.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals MaxTech NX-16, service manual, brief instructions and user manuals MaxTech NX-16. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product MaxTech NX-16.

Similar manuals

A complete manual for the device MaxTech NX-16, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use MaxTech NX-16 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of MaxTech NX-16.

A complete MaxTech manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual MaxTech NX-16 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the MaxTech NX-16, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the MaxTech NX-16, that we can find in the current document
3. Tips how to use the basic functions of the device MaxTech NX-16 - which should help us in our first steps of using MaxTech NX-16
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with MaxTech NX-16
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of MaxTech NX-16 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning MaxTech NX-16?

Use the form below

If you did not solve your problem by using a manual MaxTech NX-16, ask a question using the form below. If a user had a similar problem with MaxTech NX-16 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)