English dropdown-ico

Manual Carrier Thermidistat

12 pages 0.09 mb
Download

Go to site of 12

Summary
  • Carrier Thermidistat - page 1

    Thermidistat™ Control Installation, Start-Up, and Operating Instructions NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. INDEX Page SAFETY CONSIDERATIONS .....................................................1 INTRODUCTION .......................................... ...

  • Carrier Thermidistat - page 2

    INSTALLATION Step 1—Thermidistat Control Location Thermidistat Control should be mounted: • Approximately 5 ft (1.5m) from floor. • Close to or in a frequently used room, preferably on an inside partitioning wall. • On a section of wall without pipes or duct work. Thermidistat Control should NOT be mounted: • Close to a window, on an outs ...

  • Carrier Thermidistat - page 3

    3. A2—for 2-speed air conditioner 4. H2—for 2-speed heat pump 5. dF—for 1-speed dual fuel 6. d2—for 2-speed dual fuel 7. HS—for 1-speed heat pump with Intelligent Heat Staging (3-stage auxiliary heat with 40FK, FK4C, or FV4A Series fan coils.) When this identifier disappears, normal operation begins. The MODE control should be set to OFF ...

  • Carrier Thermidistat - page 4

    3. Use up and down buttons to move between F and C on large display. 4. Press SET TIME/TEMP button again to flash upper small display for selection of another option, or press END to exit configuration mode. Option 4—Fan (G) On With W This selection determines whether fan (G) output is to be ON or OFF when any W (furnace or strip heat) output is ...

  • Carrier Thermidistat - page 5

    Option 10—Dual Fuel Equipment All dual fuel installations must be equipped with a high pressure switch to turn off compressor under a high indoor coil pressure condition. The high pressure switch protects compressor and indoor coil from overpressure which would occur if a failure or wiring error resulted in the heat pump and furnace operating at ...

  • Carrier Thermidistat - page 6

    will be supplied, resulting in additional outputs being turned on. If room overheats, specified outputs will not turn off, guaranteeing a sufficiently warm leaving air temperature during defrost. Tempera- ture overshoot during defrost can occur, but is almost never noticeable because of the short duration of the defrost cycle (4 minutes typical, 10 ...

  • Carrier Thermidistat - page 7

    3. Use up and down buttons to move between OF and ON on large display. Factory default is OF. 4. Press SET TIME/TEMP button again to flash upper small display for selection of another option, or press END to exit configuration mode. Option 17—Enable Non-Programmable Operation This option converts the programmable Thermidistat Control to a non-pro ...

  • Carrier Thermidistat - page 8

    TO TEST COOLING AND DEHUMIDIFICATION: Press MODE button until COOL icon turns on. Cooling begins within 10 sec and remains on for 4 minutes. If system is 2-speed, low speed comes on for first 2 minutes, followed by high speed for second 2 minutes. At the end of 4-minute run, cooling stops, and MODE reverts back to OFF. At any time during 4-minute r ...

  • Carrier Thermidistat - page 9

    4. Auto and Fan Humidify The 2 choices of AUTO and FAN can be selected together. This provides both functions simultaneously. 5. Humidify Off The humidify function can be turned off completely. This does not require changing existing set points. To Select Humidification (Between NORMAL, FAN, AUTO, FAN and AUTO, or OFF) (See Table 4.) Press HUMIDITY ...

  • Carrier Thermidistat - page 10

    humidity removal is desired, this should be done, if possible. Fan coils have the capability of removing this off delay, furnaces do not. On FK or FV Fan Coils, set delay tap to 0/0. On standard fan coils, a jumper can be cut to disable off delay. Refer to fan coil Installation Instructions for details. If FAN is set for continuous operation (fan O ...

  • Carrier Thermidistat - page 11

    Vacation Dehumidification Normal Dehumidify, Cool to Dehumidify, and Dehumidify OFF, are all available in vacation mode, and selection of 1 of these can be different from that of occupied. Vacation dehumidification selection and set points are remembered the next time vacation is used. Cool to dehumidify operates slightly differently, allowing the ...

  • Carrier Thermidistat - page 12

    THERMIDIST A T CONTROL CONFIGURA TION RECORD Date Owner/Operator A) Hardware Configuration Switch A ____ AC/HP Select. (OFF = AC) Switch B ____ 1 or 2-Speed Compressor . (OFF = 1-Speed) Switch C ____ Smar t Recov ery . (OFF = Enable) Switch D ____ Installer T est. (OFF = Disab le) Thermidistat Model No. B) Mode Settings ____ Hold (On or Off) ____ M ...

Manufacturer Carrier Category Thermostat

Documents that we receive from a manufacturer of a Carrier Thermidistat can be divided into several groups. They are, among others:
- Carrier technical drawings
- Thermidistat manuals
- Carrier product data sheets
- information booklets
- or energy labels Carrier Thermidistat
All of them are important, but the most important information from the point of view of use of the device are in the user manual Carrier Thermidistat.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Carrier Thermidistat, service manual, brief instructions and user manuals Carrier Thermidistat. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Carrier Thermidistat.

Similar manuals

A complete manual for the device Carrier Thermidistat, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Carrier Thermidistat by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Carrier Thermidistat.

A complete Carrier manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Carrier Thermidistat - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Carrier Thermidistat, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Carrier Thermidistat, that we can find in the current document
3. Tips how to use the basic functions of the device Carrier Thermidistat - which should help us in our first steps of using Carrier Thermidistat
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Carrier Thermidistat
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Carrier Thermidistat in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Carrier Thermidistat?

Use the form below

If you did not solve your problem by using a manual Carrier Thermidistat, ask a question using the form below. If a user had a similar problem with Carrier Thermidistat it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)